During ISSU, "mlxsw_minimal" driver still trying to access firmware, in some cases FW could return some wrong critical threshold value which will cause switch shutdown.
**- How I did it**
In order to prevent "mlxsw_minimal" driver from accessing ASIC during ISSU, SDK will raise "OFFLINE" 'udev' event
at the early beginning of such flow. When this event is received, hw-management will remove "mlxsw_minimal" driver.
There is no need to implement the opposite "ONLINE" event since this flow is ended up with "kexec".
**- How to verify it**
repeatedly perform warm reboot, make sure there is no switch shutdown occurred.
Bugs fixes:
All | Kernel | During system reload when CPU is loaded with heavy traffic, a Kernel Panic may occur.
All | Modules, Port split | FW stuck when device rebooted with locked Optical Transceivers in split mode
Spectrum-3 | PFC | On Spectrum-3 systems, slow reaction time to Rx pause packets on 40GbE ports may lead to buffer overflow on servers.
Spectrum-3 | SN4700, Port Split | On rare occasion SN4700, conducting 100G split (4x25G) in NRZ when splitter port 1 or 2 are down, ports 3 and 4 will also go down.
Enahncments:
All | Kernel | new notification on ISSU start, so other kernel drivers can disable any interface to ASIC
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Check #6483
add test to make sure default route change in eth0 does not
affect the default route in the default vrf
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Fixes#6445
Because the ipmihelper.py script in the 9332 folder is slightly different than the common one (due to LGTM fixes), when the common one gets copied during build time it causes the workspace/build to become dirty.
Signed-off-by: Danny Allen <daall@microsoft.com>
- Why I did it
Initially, we used Monit to monitor critical processes in each container. If one of critical processes was not running
or crashed due to some reasons, then Monit will write an alerting message into syslog periodically. If we add a new process
in a container, the corresponding Monti configuration file will also need to update. It is a little hard for maintenance.
Currently we employed event listener of Supervisod to do this monitoring. Since processes in each container are managed by
Supervisord, we can only focus on the logic of monitoring.
- How I did it
We borrowed the event listener of Supervisord to monitor critical processes in containers. The event listener will take
following steps if it was notified one of critical processes exited unexpectedly:
The event listener will first check whether the auto-restart mechanism was enabled for this container or not. If auto-restart mechanism was enabled, event listener will kill the Supervisord process, which should cause the container to exit and subsequently get restarted.
If auto-restart mechanism was not enabled for this contianer, the event listener will enter a loop which will first sleep 1 minute and then check whether the process is running. If yes, the event listener exits. If no, an alerting message will be written into syslog.
- How to verify it
First, we need checked whether the auto-restart mechanism of a container was enabled or not by running the command show feature status. If enabled, one critical process should be selected and killed manually, then we need check whether the container will be restarted or not.
Second, we can disable the auto-restart mechanism if it was enabled at step 1 by running the commnad sudo config feature autorestart <container_name> disabled. Then one critical process should be selected and killed. After that, we will see the alerting message which will appear in the syslog every 1 minute.
- Which release branch to backport (provide reason below if selected)
201811
201911
[x ] 202006
**- Why I did it**
On the Mellanox platform, reboot cause is fetched from some certain sysfs which is created by the hw-management service. So determine-reboot-cause service shall start after hw-management, otherwise it could fail due to the related sysfs is not available yet.
**- How I did it**
Add a patch to the hw-management service to make sure determine-reboot-cause service should start after it.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
**- Why I did it**
- The thermalctld daemon on the Pmon docker requires support from the thermal manager API.
**- How I did it**
- Removed the old function for detecting a faulty fan.
- Removed the old function for detecting excess temperature.
- Implement thermal_manager APIs based on ThermalManagerBase
- Implement thermal_conditions APIs based on ThermalPolicyConditionBase
- Implement thermal_actions APIs based on ThermalPolicyActionBase
- Implement thermal_info APIs based on ThermalPolicyInfoBase
- Add thermal_policy.json
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
1. Fixes the missing DPKG file for gbsyncd-vs package
2. Fixes the softlink issue on the Platform-common and ztp package
3. Fixes the PYTHNON_DEBS list is missing for DBG dockers.
- Improve random number generation during early Sonic initialization by providing SW updates to Linux entropy value.
- Improve handling of platform In-Band management port
This commit provides the following updates to the Nokia ixs7215 platform
1. The Marvell Armada-38x SOC requires SW assistance to improve the system
entropy value available early on in the Sonic boot sequence.
2. The Nokia ixs7215 platform does not have a dedicated Out-Of-Band (OOB) mgmt
port and thus requires additional logic to optionally support configuring
front panel port 48 as an In-Band mgmt port. This commit provides additional
logic to manage and maintain the operation of this In-Band mgmt port.
fix platform driver breakage due to python3 upgrade and fix load minigraph errors with config load_minigraph -y
**- How I did it**
added python3-smbus to the pmon docker template since the previous was python2 specific
fixed additional "ord" python2 specific code
fixed the jinja templates used by qos reload - the template logic required data to be parsed
**- How to verify it**
run "show platform XXX" commands and verify output
run "sudo config load_minigraph -y" and verify configuration
run "show interfaces XXX" and verify output
Co-authored-by: Carl Keene <keene@nokia.com>
Centec syncd have beend upgraded to buster, docker-syncd-centec-rpc do not need generate stretch based docker.
Co-authored-by: Xianghong Gu <xgu@centecnetworks.com>
In rare case can see that xcvrd failed due to "UnboundLocalError: local variable 'label_port' referenced before assignment"
Init "label_port" as None at the beginning of the function, to avoid the case that "label_port" not assigned.
Fix#119
when parallel build is enable, multiple dpkg-buildpackage
instances are running at the same time. /var/lib/dpkg is shared
by all instances and the /var/lib/dpkg/updates could be corrupted
and cause the build failure.
the fix is to use overlay fs to mount separate /var/lib/dpkg
for each dpkg-buildpackage instance so that they are not affecting
each other.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* Enable telemetry for ARM64 by default
* [Centec]Upgrade Centec syncd docker to buster; libjemalloc2 have been installed in docker-base-buster, remove libjemalloc1 from docker-syncd-centec's Dockerfile.j2
Co-authored-by: Gu Xianghong <xgu@centecnetworks.com>
- Make PDDF code compliant with both Python 2 and Python 3
- Align code with PEP8 standards using autopep8
- Build and install both Python 2 and Python 3 PDDF packages
Starting from build (master) 176 the warm reboot on BRCM Platform started to experience syncd crash. Upon further debug by Ying it was determined that the crash was related to the following new change:
[Dynamic buffer calc] Support dynamic buffer calculation (#1338)
Ying also debugged further and found The crash was caused by buffer pool profile setting operation SAI_BUFFER_PROFILE_ATTR_SHARED_DYNAMIC_TH
A case has filed with BRCM while a potential fix was tried by Ying that seems to have addressed this issue and we are making this change available in master branch so that it will allow further feature validation/testing especially in the warm reboot area.
Once an official fix is provided by BRCM, we will then remove this in house fix and apply the official fix.
- How to verify it
Just perform warm reboot with any master code 175 or above you should see this issue or issue the following cmd will also cause the crash: "mmuconfig -p egress_lossy_profile -a 0"
- Dynamically change EEPROM driver based on media type.
- Otherwise, EEPROM INFO and DOM INFO might not be fetched properly and will result in erroneous output.
combine multiple same operation into one operation to reduce
the build steps. this is to avoid max depth exceeded issue
in the build.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Add a systemd dependency to make platform-modules service as a prerequisite for determine-reboot-cause service to ensure platform initialization is complete before determine-reboot-cause.service executes.
the control file version is 4.2.1.5-7
sonic$ sudo dpkg -i target/debs/buster/libsaibcm-dev_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm-dev_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm-dev (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm-dev (4.2.1.5-7) ...
lgh@491d842369cf:/sonic$ sudo dpkg -i target/debs/buster/libsaibcm_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm (4.2.1.5-7) ...
Processing triggers for libc-bin (2.28-10) ...
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
Features:
Spectrum-3 | Systems | Added GA-level support for SN4700 A0 system
All | Shared headroom | Added GA-level support for Shared headroom between PGs
Bugs fixes:
All | Counters | Sent traffic in certain size is wrongly increase to a smaller size counter, because port extended counter has a counter for sent traffic per packet-size range
All | Shared buffer | Configuring shared buffer on the fly may, on occasion, cause the chip to get stuck
Spectrum-2 | Modules | On occasion, link down is experienced with INPHI COLORZ PAM4 100G optic cables on SN3700 systems
- Why I did it
Make EEPROM platform APIs Python3 compliant in Nokia platform.
- How I did it
Handle bytearray type returned by read_eeprom and read_eeprom_bytes methods.
- How to verify it
Boot Nokia ixs7215 and verify PMON docker running and show platform syseeprom
Co-authored-by: Carl Keene <keene@nokia.com>
Introduce tunnel manager daemon. Start the process as part of swss container
Submodule update for swss:
9ed3026 - 2020-12-24 : [NAT] ACL Rule with DO_NOT_NAT action is getting failed. (#1502) [Akhilesh Samineni]
c39a4b1 - 2020-12-23 : Mux/IPTunnel orchagent changes (#1497) [Prince Sunny]
bc8df0e - 2020-12-23 : Add support for headroom pool watermark (#1567) [Neetha John]
**- Why I did it**
As part of migrating SONiC codebase from Python 2 to Python 3
**- How I did it**
- No longer install Python 2 in docker-base-buster or docker-config-engine-buster.
- Install Python 2 and pip2 in the following containers until we can completely eliminate it there:
- docker-platform-monitor
- docker-sonic-mgmt-framework
- docker-sonic-vs
- Pin pip2 version <21 where it is still temporarily needed, as pip version 21 will drop support for Python 2
- Also preform some other cleanup, ensuring that pip3, setuptools and wheel packages are installed in docker-base-buster, and then removing any attempts to re-install them in derived containers
* [Mellanox] Update SAI to 1.18.0
* [Mellanox] Update SDK to 4.4.2112
* Updated Mellanox SAI to 1.18.0.2
* Updated bcmsai debians to use SAI 1.7.1
* Updated Mellanox to use SAI 1.7.1
* Updated submodule sonic-sairedis using SAI 1.7.1
Co-authored-by: Vineet Mittal <vmittalmittal@microsoft.com>
Co-authored-by: Nazarii Hnydyn <nazariig@nvidia.com>
bug fix: #5914
Validated for tx_disable function of SFP+ on AS7312-54X, AS5812-54X, AS5712-54x, and AS5812-54x.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
- Why I did it
To upgrade brcm syncd to buster
- How I did it
Updated BCM SAI using kernel version 4.19.0-12 and debian 10 to support buster.
Updated syncd docker from stretch to buster in sonic-buildimage
- How to verify it
Ensured docker is running synd buster.
After upgrade, ensured all BGP peers and ip interfaces are up.
Ping to BGP neighbors is working fine.
Install the necessary python3 dependent packages to convert restore_neighbor.py
to support python3 as python2 is EOL. See: Azure/sonic-swss#1542
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
In marvell_et644m platform scripts, I have added a check to confirm the file availability before accessing it.
Signed-off-by: Sabareesh Kumar Anandan <sanandan@marvell.com>
**- Why I did it**
To support dynamic buffer calculation.
This PR also depends on the following PRs for sub modules
- [sonic-swss: [buffermgr/bufferorch] Support dynamic buffer calculation #1338](https://github.com/Azure/sonic-swss/pull/1338)
- [sonic-swss-common: Dynamic buffer calculation #361](https://github.com/Azure/sonic-swss-common/pull/361)
- [sonic-utilities: Support dynamic buffer calculation #973](https://github.com/Azure/sonic-utilities/pull/973)
**- How I did it**
1. Introduce field `buffer_model` in `DEVICE_METADATA|localhost` to represent which buffer model is running in the system currently:
- `dynamic` for the dynamic buffer calculation model
- `traditional` for the traditional model in which the `pg_profile_lookup.ini` is used
2. Add the tables required for the feature:
- ASIC_TABLE in platform/\<vendor\>/asic_table.j2
- PERIPHERAL_TABLE in platform/\<vendor\>/peripheral_table.j2
- PORT_PERIPHERAL_TABLE on a per-platform basis in device/\<vendor\>/\<platform\>/port_peripheral_config.j2 for each platform with gearbox installed.
- DEFAULT_LOSSLESS_BUFFER_PARAMETER and LOSSLESS_TRAFFIC_PATTERN in files/build_templates/buffers_config.j2
- Add lossless PGs (3-4) for each port in files/build_templates/buffers_config.j2
3. Copy the newly introduced j2 files into the image and rendering them when the system starts
4. Update the CLI options for buffermgrd so that it can start with dynamic mode
5. Fetches the ASIC vendor name in orchagent:
- fetch the vendor name when creates the docker and pass it as a docker environment variable
- `buffermgrd` can use this passed-in variable
6. Clear buffer related tables from STATE_DB when swss docker starts
7. Update the src/sonic-config-engine/tests/sample_output/buffers-dell6100.json according to the buffer_config.j2
8. Remove buffer pool sizes for ingress pools and egress_lossy_pool
Update the buffer settings for dynamic buffer calculation
python2 is end of life and SONiC is going to support python3. This PR is going to support:
1. Mellanox SONiC platform API python3 support
2. Install both python2 and python3 verson of Mellanox SONiC platform API or pmon and host side
- Enhance eeprom parsing robustness on corrupted fields
- Add chassis provisioning service
- Disable CPU sleep state on some systems
- Complete refactor for FanSlots
- Fix module unload while still in use
Barefoot platform vendors' sonic_platform packages import the Python 'thrift' library. Previously, our custom-built package was being installed in the PMon container and host OS. However, we are only building a Python 2 version of that package, which was only intended for use with saithrift.
Fixes#6077
Changes for supporting vstest for VOQ system ports. The changes include:
(1)Use of chassis_db.json is avoided since the SYSTEM_PORT is made
available in virtual chassis linecard's default_config.json which will
be loaded during bootup
(2)Core port index map file is introduced and is copied from virtual chassis
directory to hwsku direcory by start.sh
(3)vs sai profile is modified to include core port index map file name
Signed-off-by: vedganes <vedavinayagam.ganesan@nokia.com>
- Why I did it
For determining reboot-cause while running newer BIOS, SMF firmware.
- How I did it
Made changes in reboot-cause determination script to add support for behavior of newer firmware.
- How to verify it
Performed different type of resets and verified "show reboot-cause" provides the correct reason.
Logs: UT_logs.txt
- Description for the changelog
DellEMC S6100: Update reboot-cause determination to support new firmware
EEPROM cache file is not refreshed after install a new ONIE version even if the eeprom data is updated. The current Eeprom class always try to read from the cache file when the file exists. The PR is aimed to fix it.
- Change return type of SFP methods to match specification in sonic_platform_common/sfp_base.py
- Use init methods of base classes to initialize common instance variables
- Handle negative timeout values in S6100's watchdog ‘arm’ method
- Return appropriate values for 'get_target_speed', 'set_status_led' to avoid false warnings
- Implement platform module API
- Implement platform drawer API
- Complete and fix a few other platform API
- Add psu and fan support for chassis
- Fix dependency issue with determine-reboot-cause
* Update 50-ttyUSB-C0.rules
Remove some debug codes
* Update popmsg.sh
remove the debug info
* Update udev_prefix.sh
remove debug info
* Update platform-modules-haliburton.postinst
To enable the execute permission of udev scripts
* Update 50-ttyUSB-C0.rules
Fix port 13 - 48 plug out but not pop out message issue.
Signed-off-by: Jing Kan jika@microsoft.com
- Why I did it
Fix the i2c device to address conflicts behind the PCA9548 switch.
- How I did it
Load the i2c-mux-pca954x with parameter force-deselect-on-exit=1.
Submodule updates include the following commits:
* src/sonic-utilities 9dc58ea...f9eb739 (18):
> Remove unnecessary calls to str.encode() now that the package is Python 3; Fix deprecation warning (#1260)
> [generate_dump] Ignoring file/directory not found Errors (#1201)
> Fixed porstat rate and util issues (#1140)
> fix error: interface counters is mismatch after warm-reboot (#1099)
> Remove unnecessary calls to str.decode() now that the package is Python 3 (#1255)
> [acl-loader] Make list sorting compliant with Python 3 (#1257)
> Replace hard-coded fast-reboot with variable. And some typo corrections (#1254)
> [configlet][portconfig] Remove calls to dict.has_key() which is not available in Python 3 (#1247)
> Remove unnecessary conversions to list() and calls to dict.keys() (#1243)
> Clean up LGTM alerts (#1239)
> Add 'requests' as install dependency in setup.py (#1240)
> Convert to Python 3 (#1128)
> Fix mock SonicV2Connector in python3: use decode_responses mode so caller code will be the same as python2 (#1238)
> [tests] Do not trim from PATH if we did not append to it; Clean up/fix shebangs in scripts (#1233)
> Updates to bgp config and show commands with BGP_INTERNAL_NEIGHBOR table (#1224)
> [cli]: NAT show commands newline issue after migrated to Python3 (#1204)
> [doc]: Update Command-Reference.md (#1231)
> Added 'import sys' in feature.py file (#1232)
* src/sonic-py-swsssdk 9d9f0c6...1664be9 (2):
> Fix: no need to decode() after redis client scan, so it will work for both python2 and python3 (#96)
> FieldValueMap `contains`(`in`) will also work when migrated to libswsscommon(C++ with SWIG wrapper) (#94)
- Also fix Python 3-related issues:
- Use integer (floor) division in config_samples.py (sonic-config-engine)
- Replace print statement with print function in eeprom.py plugin for x86_64-kvm_x86_64-r0 platform
- Update all platform plugins to be compatible with both Python 2 and Python 3
- Remove shebangs from plugins files which are not intended to be executable
- Replace tabs with spaces in Python plugin files and fix alignment, because Python 3 is more strict
- Remove trailing whitespace from plugins files
Some syncd containers are still based on Debian Stretch, and thus do not have Python 3 available. For these containers, we must still rely on Python 2 to run supervisord_dependent_startup and supervisor-proc-exit-listener.
Fix 259 alerts reported by the LGTM tool:
- 245 for Unused import
- 7 for Testing equality to None
- 5 for Duplicate key in dict literal
- 1 for Module is imported more than once
- 1 for Unused local variable
**- Why I did it**
We were building a custom version of Supervisor because I had added patches to prevent hangs and crashes if the system clock ever rolled backward. Those changes were merged into the upstream Supervisor repo as of version 3.4.0 (http://supervisord.org/changes.html#id9), therefore, we should be able to simply install the vanilla package via pip. This will also allow us to easily move to Python 3, as Python 3 support was added in version 4.0.0.
**- How I did it**
- Remove Makefiles and patches for building supervisor package from source
- Install Python 3 supervisor package version 4.2.1 in Buster base container
- Also install Python 3 version of supervisord-dependent-startup in Buster base container
- Debian package installed binary in `/usr/bin/`, but pip package installs in `/usr/local/bin/`, so rather than update all absolute paths, I changed all references to simply call `supervisord` and let the system PATH find the executable to prevent future need for changes just in case we ever need to switch back to build a Debian package, then we won't need to modify these again.
- Install Python 2 supervisor package >= 3.4.0 in Stretch and Jessie base containers
We are facing some compilation issue while compiling mgmt framework for arm.
So, disabling Mgmt framework for marvell-armhf. We will enable it after fixing the compilation issues
Signed-off-by: Sabareesh Kumar Anandan <sanandan@marvell.com>
This release includes changes for supporting Debian Buster, fixes for internally found issues and more enhancement related to spec coverage and feature parity for Broadcom ASICs.
Additional fixes included:
CS00011465498 - Warm reboot
CS00011465061 - interfaces not coming up
CS00011396506 - nexthop resource leak
CS00011452080 - BCM SAI crash while getting lane count
In order to support SONiC physical entity mib extension, a few new platform API are added to sonic-platform-common, this PR is to provide an mellanox platform implementation for those new APIs.
* LIBSAIREDIS isn't depend on CENTEC_SAI remove this dependence
* Build depends are optimized in PR #4880 and #5039. Merge these optimization to Centec ARM64 platform.
pick up new functions and bug fixes:
- New Features
- Add dynamic minimum tables for MSN3700X, MSN3800, MSN3420, MSN4600, MSN4700 systems
- Split hw-management to one-shot init hw-management service and thermal control services.
- Bug fixes
HW Mgmt core:
- Move PSU EEPROM configuration from kernel to user space for Spectrum 2 / Spectrum 3 system
This change introduces PDDF which is described here: https://github.com/Azure/SONiC/pull/536
Most of the platform bring up effort goes in developing the platform device drivers, SONiC platform APIs and validating them. Typically each platform vendor writes their own drivers and platform APIs which is very tailor made to that platform. This involves writing code, building, installing it on the target platform devices and testing. Many of the details of the platform are hard coded into these drivers, from the HW spec. They go through this cycle repetitively till everything works fine, and is validated before upstreaming the code.
PDDF aims to make this platform driver and platform APIs development process much simpler by providing a data driven development framework. This is enabled by:
JSON descriptor files for platform data
Generic data-driven drivers for various devices
Generic SONiC platform APIs
Vendor specific extensions for customisation and extensibility
Signed-off-by: Fuzail Khan <fuzail.khan@broadcom.com>
* [Juniper] Platform bug fixes / improvements
This patch set introduces the following changes for
the two platforms.
- QFX5210
- Fixes a driver bug related to reboot notifier
- Disable pcied
- Introduces a wrapper script for fast / warm reboots
for unloading the driver containing reboot handler
- Support for PSM4 optics in media_settings
- QFX5200
- BCM configuration file updates
- Bug fixes for EM policy
- Fixes a driver bug related to reboot notifier
- Introduces a wrapper script for fast / warm reboots
for unloading the driver containing reboot handler
- Disable pcied
- Support for PSM4 optics
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
In case of non-GA SDK version there is '-' symbol in Mellanox SDK version name. (For example: 4.4.1306-006)
In appropriate .deb packet there is '.' instead of '-'. Because of this there was problem while building SDK
Signed-off-by: Andriy Yurkiv <ayurkiv@nvidia.com>
The original code tried to initialize PCA9541 without having the
driver loaded. As result the initialization didn't take effect.
Recently PCA9541 driver was added to the kernel and since then
the initialization takes effect and has negatively impacted the
platform stability.
Commenting the initialization code out to restore the original
behavior while analyzing further.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
New driver support fetching additional pages from the cable EEPROM.
There are additional information to parse now: RX/TX power, TX bias, TX fault and RX LOS.
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
Prevent intermittent build failures when building Sonic for the ARM platform architecture due to version upgrades of the redis-tools and redis-server packages.
Modify select Dockerfile templates to download the redis-tools and redis-server packages from sonicstorage rather than from debian.org.
This PR has been made possible by the inclusion of ARM versions of redis-tools and redis-server into sonicstorage as described in Issue# 5701
Why/How I did:
Make sure first error syslog is triggered based on FAULT TOLERANCE condition.
Added support of repeat clause with alert action. This is used as trigger
for generation of periodic syslog error messages if error is persistent
Updated the monit conf files with repeat every x cycles for the alert action
- Change `/run/arista` mount to pmon by `/var/run/platform_cache`
- Python3 by default for Arista platform initialisation
- Fix outstanding py2/3 compatibility issues (eeprom mostly)
- Use pytest for unit testing
- Miscellaneous modular fixes
- Implement FanDrawer and get_high_critical_threshold Platform API for S6000, S6100, Z9100 and Z9264F.
- Fix incorrect fan direction values in S6100, Z9100
The orchagent and syncd need to have the same default synchronous mode configuration. This PR adds a template file to translate the default value in CONFIG_DB (empty field) to an explicit mode so that the orchagent and syncd could have the same default mode.
When detecting a new SFP insertion, read its SFP type and DOM capability from EEPROM again.
SFP object will be initialized to a certain type even if no SFP present. A case could be:
1. A SFP object is initialized to QSFP type by default when there is no SFP present
2. User insert a SFP with an adapter to this QSFP port
3. The SFP object fail to read EEPROM because it still treats itself as QSFP.
This PR fixes this issue.
- Enable thermalctld support for our platforms
- Fix Chassis.get_num_sfp which had an off by one
- Implement read_eeprom and write_eeprom in SfpBase
- Refactor of Psus and PsuSlots. Psus they are now detected and metadata reported
- Improvements to modular support
Co-authored-by: Zhi Yuan Carl Zhao <zyzhao@arista.com>
**- Why I did it**
Install all host services and their data files in package format rather than file-by-file
**- How I did it**
- Create sonic-host-services Python wheel package, currently including procdockerstatsd
- Also add the framework for unit tests by adding one simple procdockerstatsd test case
- Create sonic-host-services-data Debian package which is responsible for installing the related systemd unit files to control the services in the Python wheel. This package will also be responsible for installing any Jinja2 templates and other data files needed by the host services.
Now we are reading base mac, product name from eeprom data, and the data read from eeprom contains multiple "\0" characters at the end, need trim them to make the string clean and display correct.
The `get_serial_number()` method in the ChassisBase and ModuleBase classes was redundant, as the `get_serial()` method is inherited from the DeviceBase class. This method was removed from the base classes in sonic-platform-common and the submodule was updated in https://github.com/Azure/sonic-buildimage/pull/5625.
This PR aligns the existing vendor platform API implementations to remove the `get_serial_number()` methods and ensure the `get_serial()` methods are implemented, if they weren't previously.
Note that this PR does not modify the Dell platform API implementations, as this will be handled as part of https://github.com/Azure/sonic-buildimage/pull/5609
Example of syslog message from Mellanox SAI:
"Oct 7 15:39:11.482315 arc-switch1025 INFO syncd#supervisord: syncd Oct 07 15:39:11 NOTICE SAI_BUFFER: mlnx_sai_buffer.c[3893]- mlnx_clear_buffer_pool_stats: Clear pool stats pool id:1"
There is a log INFO from supervisord which actually printed NOTICE and
date again. This confusion happens becuase if SAI is not built to log
to syslog it will log everything to stdout with format "[date] [level]
[message]" so supervisord sends it to syslog with level INFO.
New logs look like:
"Oct 7 15:40:21.488055 arc-switch1025 NOTICE syncd#SDK [SAI_BUFFER]: mlnx_sai_buffer.c[3893]- mlnx_clear_buffer_pool_stats: Clear pool stats pool id:17"
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
- Make DellEMC platform modules Python3 compliant.
- Change return type of PSU Platform APIs in DellEMC Z9264, S5232 and Thermal Platform APIs in S5232 to 'float'.
- Remove multiple copies of pcisysfs.py.
- PEP8 style changes for utility scripts.
- Build and install Python3 version of sonic_platform package.
- Fix minor Platform API issues.
- The issue is that the SAI package content is changed without changing its version. The DPKG caches the wrong version of SAI package.
- The fix is to include the SAI package content header for SHA calcaulation. This will detect if there is any change in the SAI package.
It should no longer be necessary to explicitly install the 'wheel' package, as SONiC packages built as wheels should specify 'wheel' as a dependency in their setup.py files. Therefore, pip[3] should check for the presence of 'wheel' and install it if it isn't present before attempting to call 'setup.py bdist_wheel' to install the package.
bring up chassisdb service on sonic switch according to the design in
Distributed Forwarding in VoQ Arch HLD
Signed-off-by: Honggang Xu <hxu@arista.com>
**- Why I did it**
To bring up new ChassisDB service in sonic as designed in ['Distributed forwarding in a VOQ architecture HLD' ](90c1289eaf/doc/chassis/architecture.md).
**- How I did it**
Implement the section 2.3.1 Global DB Organization of the VOQ architecture HLD.
**- How to verify it**
ChassisDB service won't start without chassisdb.conf file on the existing platforms.
ChassisDB service is accessible with global.conf file in the distributed arichitecture.
Signed-off-by: Honggang Xu <hxu@arista.com>
We were building our own python-click package because we needed features/bug fixes available as of version 7.0.0, but the most recent version available from Debian was in the 6.x range.
"Click" is needed for building/testing and installing sonic-utilities. Now that we are building sonic-utilities as a wheel, with Click specified as a dependency in the setup.py file, setuptools will install a more recent version of Click in the sonic-slave-buster container when building the package, and pip will install a more recent version of Click in the host OS of SONiC when installing the sonic-utilities package. Also, we don't need to worry about installing the Python 2 or 3 version of the package, as the proper one will be installed as necessary.
- SN3800 vs Cisco9236 - no link copper or optics - start sending IDLE before PHY_UP for specific OPNs
Signed-off-by: Nazarii Hnydyn <nazariig@nvidia.com>
During platform deinitialization, dell_ich is not removed properly and when we do initialize s6100 platform, ICH driver sysfs attributes are not attached. Because of this, get_transceiver_change_event returns error and this leads xcvrd to crash.
Make Python3-swsscommon available in image.
```
admin@str-s6000-acs-13:~$ sudo apt-cache search swss
libswsscommon - This package contains Switch State Service common library.
python-swsscommon - This package contains Switch State Service common Python2 library.
python3-swsscommon- This package contains Switch State Service common Python3 library.
admin@str-s6000-acs-13:~$
```
Some platforms don't leverage the brcm led coprocessor.
However ledinit will try to load a non existing file and exit with an
error code.
This change is a cosmetic fix mostly.
- How to verify it
Boot a platform without the configuration and verify in the syslog that the exit status of ledinit is 0
Boot a platform with the configuration and verify in the syslog that the exit status of ledinit is 0 and the leds are working.
Verified by adding a dumb led_proc_init.soc on an Arista platform which usually doesn't use it.
**- Why I did it**
- Platform API implementation using sonic-cfggen to get platform name and SKU name, which will fail when the database is not available.
- Chassis name is not correctly assigned, it shall be assigned with EEPROM TLV "Product Name", instead of SKU name
- Chassis model is not implemented, it shall be assigned with EEPROM TLV "Part Number"
**- How I did it**
1. Chassis
> - Get platform name from /host/machine.conf
> - Remove get SKU name with sonic-cfggen
> - Get Chassis name and model from EEPROM TLV "Product Name" and "Part Number"
> - Add function to return model
2. EEPROM
> - Add function to return product name and part number
3. Platform
> - Init EEPROM on the host side, so also can get the Chassis name model from EEPROM on the host side.
* buildimage: Add gearbox phy device files and a new physyncd docker to support VS gearbox phy feature
* scripts and configuration needed to support a second syncd docker (physyncd)
* physyncd supports gearbox device and phy SAI APIs and runs multiple instances of syncd, one per phy in the device
* support for VS target (sonic-sairedis vslib has been extended to support a virtual BCM81724 gearbox PHY).
HLD is located at b817a12fd8/doc/gearbox/gearbox_mgr_design.md
**- Why I did it**
This work is part of the gearbox phy joint effort between Microsoft and Broadcom, and is based
on multi-switch support in sonic-sairedis.
**- How I did it**
Overall feature was implemented across several projects. The collective pull requests (some in late stages of review at this point):
https://github.com/Azure/sonic-utilities/pull/931 - CLI (merged)
https://github.com/Azure/sonic-swss-common/pull/347 - Minor changes (merged)
https://github.com/Azure/sonic-swss/pull/1321 - gearsyncd, config parsers, changes to orchargent to create gearbox phy on supported systems
https://github.com/Azure/sonic-sairedis/pull/624 - physyncd, virtual BCM81724 gearbox phy added to vslib
**- How to verify it**
In a vslib build:
root@sonic:/home/admin# show gearbox interfaces status
PHY Id Interface MAC Lanes MAC Lane Speed PHY Lanes PHY Lane Speed Line Lanes Line Lane Speed Oper Admin
-------- ----------- --------------- ---------------- --------------- ---------------- ------------ ----------------- ------ -------
1 Ethernet48 121,122,123,124 25G 200,201,202,203 25G 204,205 50G down down
1 Ethernet49 125,126,127,128 25G 206,207,208,209 25G 210,211 50G down down
1 Ethernet50 69,70,71,72 25G 212,213,214,215 25G 216 100G down down
In addition, docker ps | grep phy should show a physyncd docker running.
Signed-off-by: syd.logan@broadcom.com
We want to let Monit to unmonitor the processes in containers which are disabled in `FEATURE` table such that
Monit will not generate false alerting messages into the syslog.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
libzmq5 is tcp/ipc communication library, needed by sairedis/syncd to communicate, as a new way (compared to current REDIS channel) to exchange messages which is faster than REDIS library and allows synchronous mode
this library is required in sairedis repo, swss repo, sonic-buildimage and sonic-build-tools to make it work
- Why I did it
For fixing PCA MUX attachment issue in Dell S6100 platform.
- How I did it
Wait till IOM MUX powered up properly and start I2C enumeration.
We are moving toward building all Python packages for SONiC as wheel packages rather than Debian packages. This will also allow us to more easily transition to Python 3.
Python files are now packaged in "sonic-utilities" Pyhton wheel. Data files are now packaged in "sonic-utilities-data" Debian package.
**- How I did it**
- Build and install sonic-utilities as a Python package
- Remove explicit installation of wheel dependencies, as these will now get installed implicitly by pip when installing sonic-utilities as a wheel
- Build and install new sonic-utilities-data package to install data files required by sonic-utilities applications
- Update all references to sonic-utilities scripts/entrypoints to either reference the new /usr/local/bin/ location or remove absolute path entirely where applicable
Submodule updates:
* src/sonic-utilities aa27dd9...2244d7b (5):
> Support building sonic-utilities as a Python wheel package instead of a Debian package (#1122)
> [consutil] Display remote device name in show command (#1120)
> [vrf] fix check state_db error when vrf moving (#1119)
> [consutil] Fix issue where the ConfigDBConnector's reference is missing (#1117)
> Update to make config load/reload backward compatible. (#1115)
* src/sonic-ztp dd025bc...911d622 (1):
> Update paths to reflect new sonic-utilities install location, /usr/local/bin/ (#19)
This PR limited the number of calls to sonic-cfggen to one call
per iteration instead of current 3 calls per iteration.
The PR also installs jq on host for future scripts if needed.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Refactor SFP reset, low power get/set API, and plugins with new SDK SX APIs. Previously they were calling SDK SXD APIs which have glibc dependency because of shared memory usage.
Remove implementation "set_power_override", "tx_disable_channel", "tx_disable" which using SXD APIs, once related SDK SX API available, will add them back based on new SDK SX APIs.
- Merge chassis codebase upstream
- Add support for Otterlake supervisor
- Add support for NorthFace and Camp chassis
- Add support for Eldridge, Dragonfly and Brooks fabrics
- Add support for Clearwater2 and Clearwater2Ms linecards
- Add new arista Cli to power on/off cards
- Add new arista show Cli to inspect supervisor, chassis, fabrics and linecards
- Finish the refactor of the smbus backend (huge performance enhencement)
- Split scd-hwmon kernel module in multiple source files
- Add new scd-uart driver to manage linecard consoles within a chassis
- Bootstrap of thermal platform API implementation
- Fix psud led error message
- Fix fan led color on Smartsville
When stopping the swss, pmon or bgp containers, log messages like the following can be seen:
```
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,061 ERRO pool dependent-startup event buffer overflowed, discarding event 34
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,063 ERRO pool dependent-startup event buffer overflowed, discarding event 35
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,064 ERRO pool dependent-startup event buffer overflowed, discarding event 36
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,066 ERRO pool dependent-startup event buffer overflowed, discarding event 37
```
This is due to the number of programs in the container managed by supervisor, all generating events at the same time. The default event queue buffer size in supervisor is 10. This patch increases that value in all containers in order to eliminate these errors. As more programs are added to the containers, we may need to further adjust these values. I increased all buffer sizes to 25 except for containers with more programs or templated supervisor.conf files which allow for a variable number of programs. In these cases I increased the buffer size to 50. One final exception is the swss container, where the buffer fills up to ~50, so I increased this buffer to 100.
Resolves https://github.com/Azure/sonic-buildimage/issues/5241
* [redis] Use redis-server and redis-tools in blob storage to prevent
upstream link broken
* Use curl instead of wget
* Explicitly install dependencies
Copying platform.json file into an empty /usr/share/sonic/platform directory does not mimic an actual device. A more correct approach is to create a /usr/share/sonic/platform symlink which links to the actual platform directory; this is more like what is done inside SONiC containers. Then, we only need to copy the platform.json file into the actual platform directory; the symlink takes care of the alternative path, and also exposes all the other files in the platform directory.
sonic-py-common package relies on the `PLATFORM` environment variable to be set at runtime in the SONiC VS container. Exporting the variables in the start.sh script causes the variables to only be available to the shell running start.sh and any subshells it spawns. However, once the script exits, the variable is lost. This is resulting in the failure of tests which are run in the VS container, as they call applications which in turn call sonic-py-common functions which rely on PLATFORM to be set.
Setting the environment variables in the Dockerfile allows them to persist through the entire runtime of the container.
Add a master switch so that the sync/async mode can be configured.
Example usage of the switch:
1. Configure mode while building an image
`make ENABLE_SYNCHRONOUS_MODE=y <target>`
2. Configure when the device is running
Change CONFIG_DB with `sonic-cfggen -a '{"DEVICE_METADATA":{"localhost": {"synchronous_mode": "enable"}}}' --write-to-db`
Restart swss with `systemctl restart swss`
- Reverts commit 457674c
- Creates "platform.json" for vs docker
- Adds test case for port breakout CLI
- Explicitly sets admin status of all the VS interfaces to down to be compatible with SWSS test cases, specifically vnet tests and sflow tests
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
As part of migrating all Python-based package installers to wheel format rather than Debian packages. Also to allow for easily building a Python 3 version of the package in the near future.
- Also remove some references to sonic-daemon-base which I previously missed and add missing sonic-py-common dependency for sonic-pcied.
Original converting from register is wrong, it makes the fan speed much higher than it is. Change the way fan speed is calculated from CPLD.
Signed-off-by: roy_lee <roy_lee@accton.com>
HW set qsfp port to reset at default. so need SW to set to normal when boot.
1. Modify cpld driver to invert reset offset value
2. Set to normal when boot.
Swap order of orchagent and portsyncd in start.sh and fix priorities
Many docker virtual switch tests are failing at the moment because orchagent never finishes initializing. After doing some searching I figured out that Ethernet24 is never published to State DB, which is reminiscent of #4821
Signed-off-by: Danny Allen <daall@microsoft.com>
summary of E530 platfrom:
- CPU: CTC5236, arm64
- LAN switch chip set: CENTEC CTC7132 (TsingMa). TsingMa is a purpose built device to address the challenge in the recent network evolution such as Cloud computing. CTC7132 provides 440Gbps I/O bandwidth and 400Gcore bandwidth, the CTC7132 family combines a feature-rich switch core and an embedded ARM A53 CPU Core running at 800MHz/1.2GHz. CTC7132 supports a variety of port configurations, such as QSGMII and USXGMII-M, providing full-rate port capability from 100M to 100G.
- device E530-48T4X: 48 * 10/100/1000 Base-T Ports, 4 * 10GE SFP+ Ports.
- device E530-24X2C: 24 * 10 GE SFP+ Ports, 2 * 100GE QSFP28 Ports.
add new files in three directories:
device/centec/arm64-centec_e530_24x2c-r0
device/centec/arm64-centec_e530_48t4x_p-r0
platform/centec-arm64
Co-authored-by: taocy <taocy2@centecnetworks.com>
Co-authored-by: Gu Xianghong <gxh2001757@163.com>
Co-authored-by: shil <shil@centecnetworks.com>
1. remove container feature table
2. do not generate feature entry if the feature is not included
in the image
3. rename ENABLE_* to INCLUDE_* for better clarity
4. rename feature status to feature state
5. [submodule]: update sonic-utilities
* 9700e45 2020-08-03 | [show/config]: combine feature and container feature cli (#1015) (HEAD, origin/master, origin/HEAD) [lguohan]
* c9d3550 2020-08-03 | [tests]: fix drops_group_test failure on second run (#1023) [lguohan]
* dfaae69 2020-08-03 | [lldpshow]: Fix input device is not a TTY error (#1016) [Arun Saravanan Balachandran]
* 216688e 2020-08-02 | [tests]: rename sonic-utilitie-tests to tests (#1022) [lguohan]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* Moving BRCM SAI from 3.7.5.1-1 to 3.7.5.1-2 to pick up the stubbed SAI API that were present in the header but missing in SAI implementation that cause link error during build.
In SAI header 1.5.2 there are defined SAI APIs such as "sai_query_attribute_capability()" and few other APIs that were missing the stub code in BRCM 3.7.5.1 SAI code delivery. This causes linking issue during build when we implemented the common handler to support "sai_query_attribute_capability()" that other platform supports. The expectation is that all SAI vendors must implement all the SAI header defined SAI APIs by stubbing those that they don't have the actual code support to return "SAI_STATUS_NOT_IMPLEMENTED". This allows common code for all platforms to be developed without having linking issue during build for all platforms. BRCM has provided the patch code and this PR moves the BRCM SAI from 3.7.5.1-1 to 3.7.5.1-2 to pick up those missing stubbed SAI APIs.
See BRCM case CS00010790550 for more details
Applications running in the host OS can read the platform identifier from /host/machine.conf. When loading configuration, sonic-config-engine *needs* to read the platform identifier from machine.conf, as it it responsible for populating the value in Config DB.
When an application is running inside a Docker container, the machine.conf file is not accessible, as the /host directory is not mounted. So we need to retrieve the platform identifier from Config DB if get_platform() is called from inside a Docker
container. However, we can't simply check that we're running in a Docker container because the host OS of the SONiC virtual switch is running inside a Docker container. So I refactored `get_platform()` to:
1. Read from the `PLATFORM` environment variable if it exists (which is defined in a virtual switch Docker container)
2. Read from machine.conf if possible (works in the host OS of a standard SONiC image, critical for sonic-config-engine at boot)
3. Read the value from Config DB (needed for Docker containers running in SONiC, as machine.conf is not accessible to them)
- Also fix typo in daemon_base.py
- Also changes to align `get_hwsku()` with `get_platform()`
- Created the VS setup to test DPB functionality
- Created "platform.json" for VS docker
- Added test case for Breakout CLI
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
As part of consolidating all common Python-based functionality into the new sonic-py-common package, this pull request:
1. Redirects all Python applications/scripts in sonic-buildimage repo which previously imported sonic_device_util or sonic_daemon_base to instead import sonic-py-common, which was added in https://github.com/Azure/sonic-buildimage/pull/5003
2. Replaces all calls to `sonic_device_util.get_platform_info()` to instead call `sonic_py_common.get_platform()` and removes any calls to `sonic_device_util.get_machine_info()` which are no longer necessary (i.e., those which were only used to pass the results to `sonic_device_util.get_platform_info()`.
3. Removes unused imports to the now-deprecated sonic-daemon-base package and sonic_device_util.py module
This is the next step toward resolving https://github.com/Azure/sonic-buildimage/issues/4999
Also reverted my previous change in which device_info.get_platform() would first try obtaining the platform ID string from Config DB and fall back to gathering it from machine.conf upon failure because this function is called by sonic-cfggen before the data is in the DB, in which case, the db_connect() call will hang indefinitely, which was not the behavior I expected. As of now, the function will always reference machine.conf.
* [platform] Add Support For Environment Variable
This PR adds the ability to read environment file from /etc/sonic.
the file contains immutable SONiC config attributes such as platform,
hwsku, version, device_type. The aim is to minimize calls being made
into sonic-cfggen during boot time.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
virtual-chassis test uses multiple vs instances to simulate a
modular switch and a redis-chassis service is required to run on
the vs instance that represents a supervisor card.
This change allows vs docker start redis-chassis service according
to external config file.
**- Why I did it**
To support virtual-chassis setup, so that we can test distributed forwarding feature in virtual sonic environment, see `Distributed forwarding in a VOQ architecture HLD` pull request at https://github.com/Azure/SONiC/pull/622
**- How I did it**
The sonic-vs start.sh is enhanced to start new redis_chassis service if external chassis config file found. The config file doesn't exist in current vs environment, start.sh will behave like before.
**- How to verify it**
The swss/test still pass. The chassis_db service is verified in virtual-chassis topology and tests which are in following PRs.
Signed-off-by: Honggang Xu <hxu@arista.com>
(cherry picked from commit c1d45cf81ce3238be2dcbccae98c0780944981ce)
Co-authored-by: Honggang Xu <hxu@arista.com>
when parallel build is enabled, both docker-fpm-frr and docker-syncd-brcm
is built at the same time, docker-fpm-frr requires swss which requires to
install libsaivs-dev. docker-syncd-brcm requires syncd package which requires
to install libsaibcm-dev.
since libsaivs-dev and libsaibcm-dev install the sai header in the same
location, these two packages cannot be installed at the same time. Therefore,
we need to serialize the build between these two packages. Simply uninstall
the conflict package is not enough to solve this issue. The correct solution
is to have one package wait for another package to be uninstalled.
For example, if syncd is built first, then it will install libsaibcm-dev.
Meanwhile, if the swss build job starts and tries to install libsaivs-dev,
it will first try to query if libsaibcm-dev is installed or not. if it is
installed, then it will wait until libsaibcm-dev is uninstalled. After syncd
job is finished, it will uninstall libsaibcm-dev and swss build job will be
unblocked.
To solve this issue, _UNINSTALLS is introduced to uninstall a package that
is no longer needed and to allow blocked job to continue.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Consolidate common SONiC Python-language functionality into one shared package (sonic-py-common) and eliminate duplicate code.
The package currently includes three modules:
- daemon_base
- device_info
- logger
Added required packages to enabled YANG dependency check for Dynamic Port Breakout in VS container.
[sonic-utilities PR #766](https://github.com/Azure/sonic-utilities/pull/766) has a dependency on it.
Getting error like the following without this fix: `ImportError: No module named yang - required module not found`
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
the command kills all exabgp processes on the host.
since the namespaces are newly added, there should
be no prior exabgp processes.
if it is existing namespace, it is also the dvs
framework job to clean up all prior processes.
Align SFP key names with new standard defined in https://github.com/Azure/sonic-platform-common/pull/97
- hardwarerev -> hardware_rev
- serialnum -> serial
- manufacturename -> manufacturer
- modelname -> model
- Connector -> connector
Added xmltodict and jsondiff packages needed to run vs test cases successfully for DPB.
sonic-utilities PR #766 has a dependency on these packages.
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
1) Fixing the issues while applying platform TxCTLE settings in sfputil.py for QFX5200
2) Adding the support for transceiver dom threshold info in sfputil.py for both QFX5210 & QFX5200 platforms
3) Updating the sfputil.py for QFX5210 & QFX5200 platforms
4) Adding a new platform specific command 'show_thresholds' to display the FAN dutycycle percentage for various temperature ranges (for both AFI & AFO QFX5200 systems).
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
System health feature needs to set/get system led status
- Add a led object in chassis class and initialize it when the API is called on host side
- Read/write system led system fs to get/set the status
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
This PR has changes to support accessing the bcmsh and bcmcmd utilities on multi ASIC devices
Changes done
- move the link of /var/run/sswsyncd from docker-syncd-brcm.mk to docker_image_ctl.j2
- update the bcmsh and bcmcmd scripts to take -n [ASIC_ID] as an argument on multi ASIC platforms
- Xilinx/pericom peripherals are not actively used in DellEMC S6100 switch.
- These peripherals are throwing PCIE corrected messages in some of the units and filling syslog.
- Since it is not usable disabling it at startup.
make swss build depends only on libsairedis instead of syncd. This allows to build swss without depending
on vendor sai library.
Currently, libsairedis build also buils syncd which requires vendor SAI lib. This makes difficult to build
swss docker in buster while still keeping syncd docker in stretch, as swss requires libsairedis which also
build syncd and requires vendor to provide SAI for buster. As swss docker does not really contain syncd
binary, so it is not necessary to build syncd for swss docker.
* [submodule]: update sonic-sairedis
* ccbb3bc 2020-06-28 | add option to build without syncd (HEAD, origin/master, origin/HEAD) [Guohan Lu]
* 4247481 2020-06-28 | install saidiscovery into syncd package [Guohan Lu]
* 61b8e8e 2020-06-26 | Revert "sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624)" (#630) [Danny Allen]
* 85e543c 2020-06-26 | add a README to tests directory to describe how to run 'make check' (#629) [Syd Logan]
* 2772f15 2020-06-26 | sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624) [Syd Logan]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
1. Upgrade SAI headers to v1.6.3
2. Fix traffic lost during FFB related to buffer config + optimize buffer config timing for FB
3. Add ACL fields BTH, IP flags
4. Add ACL infrastructure of different fields per ASIC type
**- Why I did it**
System health feature requires to read ASIC temperature and threshold from platform API
**- How I did it**
Implement Chassis.get_asic_temperature and Chassis.get_asic_temperature_threshold by getting value from system fs.
This patch addresses the following issues:
1) Platform drivers were not loading in the latest images. Fixed
the intialization script to make sure that all the drivers are
loaded.
2) Getting rid of "pstore: crypto_comp_decompress failed, ret = -22!"
messages during the kernel boot, after moving to 4.19 kernel. The
solution is to remove the files under '/sys/fs/pstore' directory.
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
**- Why I did it**
Initially, the critical_processes file contains either the name of critical process or the name of group.
For example, the critical_processes file in the dhcp_relay container contains a single group name
`isc-dhcp-relay`. When testing the autorestart feature of each container, we need get all the critical
processes and test whether a container can be restarted correctly if one of its critical processes is
killed. However, it will be difficult to differentiate whether the names in the critical_processes file are
the critical processes or group names. At the same time, changing the syntax in this file will separate the individual process from the groups and also makes it clear to the user.
Right now the critical_processes file contains two different kind of entries. One is "program:xxx" which indicates a critical process. Another is "group:xxx" which indicates a group of critical processes
managed by supervisord using the name "xxx". At the same time, I also updated the logic to
parse the file critical_processes in supervisor-proc-event-listener script.
**- How to verify it**
We can first enable the autorestart feature of a specified container for example `dhcp_relay` by running the comman `sudo config container feature autorestart dhcp_relay enabled` on DUT. Then we can select a critical process from the command `docker top dhcp_relay` and use the command `sudo kill -SIGKILL <pid>` to kill that critical process. Final step is to check whether the container is restarted correctly or not.
**- Why I did it**
After discussed with Joe, we use the string "/usr/bin/syncd\s" in Monit configuration file to monitor
syncd process on Broadcom and Mellanox. Due to my careless, I did not find this bug during the
previous testing. If we use the string "/usr/bin/syncd" in Monit configuration file to monitor the
syncd process, Monit will not detect whether syncd process is running or not.
If we ran the command `sudo monit procmactch “/usr/bin/syncd”` on Broadcom, there will be three
processes in syncd container which matched this "/usr/bin/syncd": `/bin/bash /usr/bin/syncd.sh
wait`, `/usr/bin/dsserve /usr/bin/syncd –diag -u -p /etc/sai.d/sai.profile` and `/usr/bin/syncd –diag -
u -p /etc/sai.d/said.profile`. Monit will select the processes with the highest uptime (at there
`/bin/bash /usr/bin/syncd.sh wait`) to match and did not select `/usr/bin/syncd –diag -u -p
/etc/sai.d/said.profile` to match.
Similarly, On Mellanox Monit will also select the process with the highest uptime (at there
`/bin/bash /usr/bin/syncd.sh wait`) to match and did not select `/usr/bin/syncd –diag -u -p
/etc/sai.d/said.profile` to match.
That is why Monit is unable to detect whether syncd process is running or not if we use the string “/usr/bin/syncd” in Monit configuration file. If we use the string "/usr/bin/syncd\s" in Monit configuration file, Monit can filter out the process `/bin/bash /usr/bin/syncd.sh wait` and thus can correctly monitor the syncd process.
**- How I did it**
**- How to verify it**
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Change port index in port_config.ini to 1-based
* Add default port index to port_config.ini, change platform plugins to accept 1-based port index
* fix port index in sfp_event.py
**- Why I did it**
The tx_disable function isn't work for the accton_ax5835-54x device.
**- How I did it**
Fix the incorrect path of the sfp node path inside the util file.
**- How to verify it**
Test with
"sudo accton_as5835_54x_util.py show"
"sudo accton_as5835_54x_util.py set sfp"
There should see correct value for module_present and module_tx_disable. And should able to set it.
Signed-off-by: kuanyu_chen <kuanyu_chen@edge-core.com>
The `-sv2` suffix was used to differentiate SNMP Dockers when we transitioned from "SONiCv1" to "SONiCv2", about four years ago. The old Docker materials were removed long ago; there is no need to keep this suffix. Removing it aligns the name with all the other Dockers.
Also edit Monit configuration to detect proper snmp-subagent command line in Buster, and make snmpd command line matching more robust.
- Add .gitignore files in each subdirectory of src/, so as to reduce the size of the .gitignore file in the project root, and also make it easier to maintain (i.e., if a directory in src/ is removed, there will not be outdated entries in the root .gitignore file.
- Also add missing .gitignore entries and remove outdated entries and duplicates.
The -sv2 suffix was used to differentiate SNMP Dockers when we transitioned from "SONiCv1" to "SONiCv2", about four years ago. The old Docker materials were removed long ago; there is no need to keep this suffix. Removing it aligns the name with all the other Dockers.
**- Why I did it**
For decoding system EEPROM of S6000 based on Dell offset format and S6000-ON’s system EEPROM in ONIE TLV format.
**- How I did it**
- Differentiate between S6000 and S6000-ON using the product name available in ‘dmi’ ( “/sys/class/dmi/id/product_name” )
- For decoding S6000 system EEPROM in Dell offset format and updating the redis DB with the EEPROM contents, added a new class ‘EepromS6000’ in eeprom.py,
- Renamed certain methods in both Eeprom, EepromS6000 classes to accommodate the plugin-specific methods.
**- How to verify it**
- Use 'decode-syseeprom' command to list the system EEPROM details.
- Wrote a python script to load chassis class and call the appropriate methods.
UT Logs: [S6000_eeprom_logs.txt](https://github.com/Azure/sonic-buildimage/files/4735515/S6000_eeprom_logs.txt), [S6000-ON_eeprom_logs.txt](https://github.com/Azure/sonic-buildimage/files/4735461/S6000-ON_eeprom_logs.txt)
Test script: [eeprom_test_py.txt](https://github.com/Azure/sonic-buildimage/files/4735509/eeprom_test_py.txt)
- Sensor and Fan information added to primary platforms for thermal API.
- Refactors involving better abstractions, code reuse and dead code removal.
- Improvements to the diag capabilities
- Pylintrc added to improve code quality. Will become fatal at a later time.
Co-authored-by: Baptiste Covolato <baptiste@arista.com>
Cleanup description string
First port (management port) are excluded from general port naming scheme.
Management port are excluded from general port naming scheme.
before:
|on GNS3 |in SONiC |
|---------|---------|
|Ethernet0|eth0 |
|Ethernet1|Ethernet0|
|Ethernet2|Ethernet4|
|Ethernet3|Ethernet8|
after:
|on GNS3 |in SONiC |
|---------|---------|
|eth0 |eth0 |
|Ethernet0|Ethernet0|
|Ethernet1|Ethernet4|
|Ethernet2|Ethernet8|
Signed-off-by: Masaru OKI <masaru.oki@gmail.com>
* Update sonic-sairedis (sairedis with SAI 1.6 headers)
* Update SAIBCM to 3.7.4.2, which is built upon SAI1.6 headers
* missed updating BRCM_SAI variable, fixed it
* Update SAIBCM to 3.7.4.2, updated link to libsaibcm
* [Mellanox] Update SAI (release:v1.16.3; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* Update sonic-sairedis pointer to include SAI1.6 headers
* [Mellanox] Update SDK to 4.4.0914 and FW to xx.2007.1112 to match SAI 1.16.3 (API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* ensure the veth link is up in docker VS container
* ensure the veth link is up in docker VS container
* [Mellanox] Update SAI (release:v1.16.3.2; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* use 'config interface startup' instead of using ifconfig command, also undid the previous change'
Co-authored-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
- Skip thermalctld in DellEMC S6000, S6100, Z9100 and Z9264 platforms.
- Change the return type of thermal Platform APIs in DellEMC S6000, S6100, Z9100 and Z9264 platforms to 'float'.
* [platform]: Add a new supported platform, Delta-agc032
Switch Vendor: Delta
Switch SKU: Delta-agc032
CPU: BROADWELL-DE
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk3, BCM56980
Port Configuration: 32x400G + 2x10G
- What I did
Add a new Delta platform Delta-agc032.
- How I did it
Add files by following SONiC Porting Guide.
- How to verify it
1. decode-syseeprom
2. sensors
3. psuutil
4. sfputil
5. show interface status
6. bcmcmd
Signed-off-by: zoe-kuan <ZOE.KUAN@deltaww.com>
3y Power YPEB-1200am PSU doens't support read fan_dir from pmbus register
Check with vendor this PUS type only support F2B fan direction. So add to show "F2B"
when red psu_fan_dir sysfs.
* Trigger thermal action log only if thermal condition changes
* test file existence before read file content
* fix error for set psu fan speed
* Remove logs because it print too frequently
- bug fix : Fixed an issue which the nps ko file was not loaded due to the wrong service file name
- Optimize the code to reduce changes due to the kernel upgrade
- Remove nephos ko file loaded in swss.service.j2 because it has loaded at syncd.service.j2
For detecting transceiver change events through xcvrd in DellEMC S6000, S6100 and Z9100 platforms.
- In S6000, rename 'get_transceiver_change_event' in chassis.py to 'get_change_event' and return appropriate values.
- In S6100, implement 'get_change_event' through polling method (poll interval = 1 second) in chassis.py (Transceiver insertion/removal does not generate interrupts due to a CPLD bug)
- In Z9100, implement 'get_change_event' through interrupt method using select.epoll().
This patchset implement the following:
- Setting the FAN frequency
- Corrections to the EM policy with respect to platform
defined temperature / fan values
- Updates to the platform monitorng script logging
- Fixes to platform initialization script
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
Update SAI/SDK/FW and MSN4700 device files to support 8 lanes 400G
Update SAI to 1.16.3
Update SDK to 4.4.0914
Update FW to *.2007.1112
Update MSN4700 device files to support 8 lanes 400G
currently, vs docker always create 32 front panel ports.
when vs docker starts, it first detects the peer links
in the namespace and then setup equal number of front panel
interfaces as the peer links.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
- Add Makefile rules to build debug containers for SWI images
- Fix some platform API implementation for xcvrd and thermalctld
- Improvements to arista diag command
- Miscellaneous refactors
Co-authored-by: Maxime Lorrillere <mlorrillere@arista.com>
* New SKU support for MSN3420
Signed-off-by: Shlomi Bitton <shlomibi@mellanox.com>
Conflicts:
device/mellanox/x86_64-mlnx_msn2700-r0/plugins/sfputil.py
* Add CPLD's
* Symlink fixes and semantics
* Adding new platform at end of lines
This patch set implements the following:
- Fixes the conflicts in chassis.py / platform.py in sonic_platfrom
- Consolidating the common library files in sonic_platform
- Moving QFX5210 specific drivers to qfx5210/modules
- Moving Juniper common fpga drivers to common/modules
- Cleaning up the platform driver files
- Bug fixes in QFX5210 platform monitor & initialiazation script
- Fixing the bugs in QFX5210 eeprom parsing
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
[baseimage]: upgrade base image to debian buster
bring up the base image to debian buster 4.19 kernel.
using the merge commits to preserve the individual commits to better track the history.
Currently we port SONiC to buster in a way that base image is on buster and
other dockers based on stretch. The benefit is that tasks can be carried out
simultaneously.
The build procedure can be treated as 2 stages.
The first stage is to build the stretch-based debs and dockers and the second
stage is to build the buster-based ones.
One thing we have to pay attention to is some debs depend on kernel should not
be built at stretch stage because the kernel isn't available at that time.
The idea is to move that kind of debs out of SONIC_STRETCH_DEBS. Meanwhile,
any dependency explicitly put on the stretch based dockers on kernel should be
removed.
1. undefine led_classdev_register as it is defined in leds.h
2. header file location change
a. linux/i2c/pmbus.h -> linux/pmbus.h
b. linux/i2c-mux-gpio.h -> linux/platform_data/i2c-mux-gpio.h
c. linux/i2c/pca954x.h -> linux/platform_data/pca954x.h
- build SONIC_STRETCH_DOCKERS in sonic-slave-stretch docker
- build image related module in sonic-slave-buster docker.
This includes all kernels modules and some packages
Signed-off-by: Guohan Lu <lguohan@gmail.com>
This is a 1RU switch with 32 QSFP28 (40G/100G) ports on
Broadcom Tomahawk I chipset. CPU used in QFX5200-32C-S
is Intel Ivy Bridge. The machine has Redundant and
hot-swappable Power Supply (1+1) and also has Redundant
and hot swappable fans (5).
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
Signed-off-by: Ashish Bhensdadia <bashish@juniper.net>
FPGA driver crash fix for stale buffer in i2c transfer
LED firmware load issue fix.
10G port swapfix
psu/sfp bug fixes to report correct states/status of hw
libpython2.7, libdaemon0, libdbus-1-3, libjansson4 are common
across different containers. move them into docker-base-stretch
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* [thermal control] Fix pmon docker stop issue on 3800
* [thermal fix] Fix QA test issue
* [thermal fix] change psu._get_power_available_status to psu.get_power_available_status
* [thermal fix] adjust log for PSU absence and power absence
* [thermal fix] add unit test for loading thermal policy file with duplicate conditions in different policies
* [thermal] fix fan.get_presence for non-removable SKU
* [thermal fix] fix issue: fan direction is based on drawer
* Fix issue: when fan is not present, should not read fan direction from sysfs but directly return N/A
* [thermal fix] add unit test for get_direction for absent FAN
* Unplugable PSU has no FAN, no need add a FAN object for this PSU
* Update submodules
Co-authored-by: Stephen Sun <5379172+stephenxs@users.noreply.github.com>
* add MSN4700 device files
* update ACS-MSN4700 sai profile
* update buffer pool size, headroom, sensor conf, port config and reboot scripts
* fix ident
* update sensor conf and buffer pool
* [sn4700] add sku 4700 to chassis.py
* [Mellanox-4700] Add 4700 info to psu and thermal platform API
* update buffer config file template to the latest.
update SAI profile to use 100G X 4lanes for now
update port_config.ini according to the SAI profile
* [Mellanox]Update the buffer configurations for 4700
* fix alignment in pg_profile_lookup.ini
* add platform components file for new sku
* Update device/mellanox/x86_64-mlnx_msn4700-r0/ACS-MSN4700/pg_profile_lookup.ini
Co-Authored-By: Nazarii Hnydyn <nazariig@mellanox.com>
* remove redundant line
* [Mellanox]Correct type, buffer size
Co-authored-by: Nazarii Hnydyn <nazariig@mellanox.com>
Co-authored-by: junchao <junchao@mellanox.com>
Co-authored-by: Stephen Sun <stephens@mellanox.com>
In the file "files/build_templates/docker_image_ctl.j2", it adds the option
"--net" to the docker create command through the commit
"abe7ef7e2e2e1215c97cee19a83aab0b130cebe5" (#3856).
Remove the "--net" option in "docker-syncd-brcm-rpc.mk" to avoid
specifying duplicated "--net" options.
Signed-off-by: charlie_chen <charlie_chen@edge-core.com>
DPKG caching framework provides the infrastructure to cache the sonic module/target .deb files into a local cache by tracking the target dependency files.SONIC build infrastructure is designed as a plugin framework where any new source code can be easily integrated into sonic as a module and that generates output as a .deb file. The source code compilation of a module is completely independent of other modules compilation. Inter module dependency is resolved through build artifacts like header files, libraries, and binaries in the form of Debian packages. For example module A depends on module B. While module A is being built, it uses B's .deb file to install it in the build docker.
The DPKG caching framework provides an infrastructure that caches a module's deb package and restores it back to the build directory if its dependency files are not modified. When a module is compiled for the first time, the generated deb package is stored at the DPKG cache location. On the subsequent build, first, it checks the module dependency file modification. If none of the dependent files is changed, it copies the deb package from the cache location, otherwise, it goes for local compilation and generates the deb package. The modified files should be checked-in to get the newer cache deb package.
This provides a huge improvement in build time and also supports the true incremental build by tracking the dependency files.
- How I did it
It takes two global arguments to enable the DPKG caching, the first one indicates the caching method and the second one describes the location of the cache.
SONIC_DPKG_CACHE_METHOD=cache
SONIC_DPKG_CACHE_SOURCE=
where SONIC_DPKG_CACHE_METHOD - Default method is 'cache' for deb package caching
none: no caching
cache: cache from local directory
Dependency file tracking:
Dependency files are tracked for each target in two levels.
1. Common make infrastructure files - rules/config, rules/functions, slave.mk etc.
2. Per module files - files which are specific to modules, Makefile, debian/rules, patch files, etc.
For example: dependency files for Linux Kernel - src/sonic-linux-kernel,
SPATH := $($(LINUX_HEADERS_COMMON)_SRC_PATH)
DEP_FILES := $(SONIC_COMMON_FILES_LIST) rules/linux-kernel.mk rules/linux-kernel.dep
DEP_FILES += $(SONIC_COMMON_BASE_FILES_LIST)
SMDEP_FILES := $(addprefix $(SPATH)/,$(shell cd $(SPATH) && git ls-files))
DEP_FLAGS := $(SONIC_COMMON_FLAGS_LIST) \
$(KERNEL_PROCURE_METHOD) $(KERNEL_CACHE_PATH)
$(LINUX_HEADERS_COMMON)_CACHE_MODE := GIT_CONTENT_SHA
$(LINUX_HEADERS_COMMON)_DEP_FLAGS := $(DEP_FLAGS)
$(LINUX_HEADERS_COMMON)_DEP_FILES := $(DEP_FILES)
$(LINUX_HEADERS_COMMON)_SMDEP_FILES := $(SMDEP_FILES)
$(LINUX_HEADERS_COMMON)_SMDEP_PATHS := $(SPATH)
Cache file tracking:
The Cache file is a compressed TAR ball of a module's target DEB file and its derived-target DEB files.
The cache filename is formed with the following format
FORMAT:
<module deb filename>.<24 byte of DEP SHA hash >-<24 byte of MOD SHA hash>.tgz
Eg:
linux-headers-4.9.0-9-2-common_4.9.168-1+deb9u3_all.deb-23658712fd21bb776fa16f47-c0b63ef593d4a32643bca228.tgz
< 24-byte DEP SHA value > - the SHA value is derived from all the dependent packages.
< 24-byte MOD SHA value > - the SHA value is derived from either of the following.
GIT_COMMIT_SHA - SHA value of the last git commit ID if it is a submodule
GIT_CONTENT_SHA - SHA value is generated from the content of the target dependency files.
Target Specific rules:
Caching can be enabled/disabled on a global level and also on the per-target level.
$(addprefix $(DEBS_PATH)/, $(SONIC_DPKG_DEBS)) : $(DEBS_PATH)/% : .platform $$(addsuffix -install,$$(addprefix $(DEBS_PATH)/,$$($$*_DEPENDS))) \
$(call dpkg_depend,$(DEBS_PATH)/%.dep )
$(HEADER)
# Load the target deb from DPKG cache
$(call LOAD_CACHE,$*,$@)
# Skip building the target if it is already loaded from cache
if [ -z '$($*_CACHE_LOADED)' ] ; then
.....
# Rules for Generating the target DEB file.
.....
# Save the target deb into DPKG cache
$(call SAVE_CACHE,$*,$@)
fi
$(FOOTER)
The make rule-'$(call dpkg_depend,$(DEBS_PATH)/%.dep )' checks for target dependency file modification. If it is newer than the target, it will go for re-generation of that target.
Two main macros 'LOAD_CACHE' and 'SAVE_CACHE' are used for loading and storing the cache contents.
The 'LOAD_CACHE' macro is used to load the cache file from cache storage and extracts them into the target folder. It is done only if target dependency files are not modified by checking the GIT file status, otherwise, cache loading is skipped and full compilation is performed.
It also updates the target-specific variable to indicate the cache is loaded or not.
The 'SAVE_CACHE' macro generates the compressed tarball of the cache file and saves them into cache storage. Saving into the cache storage is protected with a lock.
- How to verify it
The caching functionality is verified by enabling it in Linux kernel submodule.
It uses the cache directory as 'target/cache' where Linux cache file gets stored on the first-time build and it is picked from the cache location during the subsequent clean build.
- Description for the changelog
The DPKG caching framework provides the infrastructure to save the module-specific deb file to be cached by tracking the module's dependency files.
If the module's dependency files are not changed, it restores the module deb files from the cache storage.
- Description for the changelog
- A picture of a cute animal (not mandatory but encouraged)
DOCUMENT PR:
https://github.com/Azure/SONiC/pull/559
Take advantage of an SDK environment variable to customize the location where sdk_socket exists.
In the latest SDK sdk_socket has been moved from /tmp to /var/run which is a better place to contain this kind of file.
However, this prevents the subdirs under /var/run from being mapped to different volumes. To resolve this, we take advantage of an SDK variable to designate the location of sdk_socket.
This requires every process that requires to access sdk_socket have this environment variable defined. However, to define environment variable for each process is less scalable. We take advantage of the docker scope environment variable to avoid that.
It depends on PR 4227
* [Mellanox]Integrate hw-mgmt 7.0000.3012
* [sonic-linux-kernel]Advance the submodule head
Advance the sonic-linux-kernel
[sFlow]: Patch to fix skb_over_panic in psample driver (#120)
Added support in the kernel for fullcone 3-tuple unique nat. (#100)
Adding support to compile ARM architecture (#102)
[ixgbe] Support bcm54616s external phy in ixgbe (#122)
Fix i2c ISMT DMA buffer alignment issue (#123)
[mellanox]: Add SN4700 patches. (#126)
* Add new CIG device CS6436-54P and CS5435-54P, also update code for CS6436-56P
* security kernel update to 4.9.189 for CIG devices
* security kernel update to 4.9.189 for CIG devices
* Update rules
Update rule file
update FW to xx_2000_3298
update SAI to 1.16.0
update Spectrum-1 and Spectrum-2 buffer pool size according to the new SDK default config change.
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t1.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t1.j2
modified: fw.mk
modified: mlnx-sai.mk
modified: mlnx-sai/SAI-Implementation
modified: sdk-src/sx-kernel/Switch-SDK-drivers
modified: sdk.mk
signed-off by kebol@mellanox.com
Due to linux create hwmonN node number, N isn't fixed. So modify to use "" to let thermal.py can correct sysfs. For example, use /sys/bus/i2c/devices/55-0048/hwmon/hwmon/temp1_input to instead of /sys/bus/i2c/devices/55-0048/hwmon/hwmon4/temp1_input
This patch upgrade the kernel from version
4.9.0-9-2 (4.9.168-1+deb9u3) to 4.9.0-11-2 (4.9.189-3+deb9u2)
Co-authored-by: rajendra-dendukuri <47423477+rajendra-dendukuri@users.noreply.github.com>
- Fix for Azure/sonic-buildimage#4095
- Exit status from failed make command(action) didnt reached parent target because the make command is inside the "for" loop.
- Only the exit status of the last command in the last iteration of the for loop is read by parent target.
- This is the reason why dpkg-buildpackage ignored the make error.
- Fixed the issue with help of "set -e".
- Added support for Thermal event in Last Reboot Reason "show reboot-cause" command.
- Added support for sending log message in case of thermal shutdown.
sonic NOTICE root: Shutting down due to over temperature (40 degree, 30 degree, 34 degree)
* Changes in sonic-buildimage for the NAT feature
- Docker for NAT
- installing the required tools iptables and conntrack for nat
Signed-off-by: kiran.kella@broadcom.com
* Add redis-tools dependencies in the docker nat compilation
* Addressed review comments
* add natsyncd to warm-boot finalizer list
* addressed review comments
* using swsscommon.DBConnector instead of swsssdk.SonicV2Connector
* Enable NAT application in docker-sonic-vs
Implement classes IpmiSensor, IpmiFru to obtain platform sensors information for Platform2.0 APIs in DellEMC Z9264 platform.
Add a new file ipmihelper.py with the implementation for IpmiSensor, IpmiFru classes.
- move single instance services into their own folder
- generate Systemd templates for any multi-instance service files in slave.mk
- detect single or multi-instance platform in systemd-sonic-generator based on asic.conf platform specific file.
- update container hostname after creation instead of during creation (docker_image_ctl)
- run Docker containers in a network namespace if specified
- add a service to create a simulated multi-ASIC topology on the virtual switch platform
Signed-off-by: Lawrence Lee <t-lale@microsoft.com>
Signed-off-by: Suvarna Meenakshi <Suvarna.Meenaksh@microsoft.com>
- Sfp,Eeprom,Chassis(transceiver change event) support added for z9264f Platform 2.0 API
- Added Interrupt handler to SFP change event in dell_z9264f_fpga_ocores.c
- Fixed few indentation and offset issues in sfputil.py for z9264f
- Implemented fancontrol service to monitor S6000 fans and adjust fan speed w.r.t temperature.
- fancontrol.service starts the fancontrol script at startup.
- This script takes the average temperature by reading three sensors and configure FANS to appropritate RPM against the temperature.
- When the temperature is adjusted script will log in syslog for future reference.
- Also, script checks for faulty fans and report the status in syslog.
Since the syncd process running on different platforms will have the different full path names, we
change the full path name of process syncd in the monit config file such that it will be universal and is not for a specific vendor.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [MultiDB] (except ./src and ./dockers dirs): replace redis-cli with sonic-db-cli and use new DBConnector
* update comment for a potential bug
* update comment
* add TODO maker as review reqirement
* Update arista driver submodule
* Add support for 7260CX3-64E in boot0
* Refactor boot0 platform specific definition
Make it easier to manage new sku
* Add support for 7050CX3-32S in boot0
Just contains the required boot0 information
* Add basic plugin support for DCS-7050CX3-32S
* Add port config for Arista-7050CX3-32S-C32
Co-authored-by: yurypm <yurypm@arista.com>
Co-authored-by: byu343 <byu@arista.com>
* [initramfs] Updated reuired tools for initramfs
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* [initramfs] Updated required tools for initramfs
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* [Platform] [Marvell] Platform specific debian package for et6448m device
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* Removed auto-generated files
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* [initramfs] Added mtd and uboot firmware tools package required for arm arch
Its been enabled to all arch including amd64
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* [initramfs] Added mtd and uboot firmware tools package required for arm arch
Its been enabled to all arch including amd64
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* [initramfs] Marvell arm modules update and platform config update
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* [iniramfs] add initramfs uboot-utils hook script only for ARM
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* Add a monit config file for teamd container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file in teamd container
into base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for snmp container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of snmp container into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for dhcp_relay container in the dir
base_image_files.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of dhcp_relay
container into base image under /etc/monit/conf.d.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for router advertiser container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of router advertiser
contianer into base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Pmon] Add a monit config file for pmon container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Pmon] Add a copy mechanism to put the monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Add a monit config file for lldp container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Add a copy mechanism to put the monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Add a monit config file for BGP container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Add a copy mechanism to put monit config file into the base
image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Add a monit config file for the swss container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Add a copy mechanism to put monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on barefoot
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-centec] Add a monit config file for syncd container on centen
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on centen
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit conifg file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on
marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on
marvell-armhf.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on nephos.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Add a monit config file for sflow container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Add a copy mechanism to put the monit conifg file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Add a monit config file for telemetry container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Add a copy mechanism to put the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Add a monit config file for database container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Dhcprelay] Change a typo.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Dhcprelay] Change the process name in monit config file to
dhcrelay.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no desserve process in syncd container on
barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process desserve in syncd container on
cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process named desserve in syncd on centec.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process named desserve in syncd on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Should not delete the process desserve in syncd container
on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
marvell-armhf.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Radv] Change the process name to radvd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Correct a typo in monit_telemetry.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-teamd] Delete the monit config file for teamd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-teamd] Delete the mechanism to copy the monit config file into
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-dhcprelay] Delete the monit config file for dhcp_relay
container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-dhcprelay] Delete the mechanism to copy the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-radv] Delete the monit config file foe radv container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-radv] Delete the mechanism to copy the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] change the monit config file for BGP container such that
monit only generates alert if the process is not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-snmp] Change the monit config file for snmp container such that
monit only generates alret if the process is not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Change the monit config file for pmon container such that
monit only generates alert if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Change the monit config file for lldp container such that
monit only generates alerts if some processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Delete the monit config file for pmon container since some
of processes are not running depended on the type of box.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Delete the copy mechanism to copy the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Change the matching name for the process lldpd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Change the monit config file for swss container such that
monit only generates alerts if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
barefoot such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Correct a typo in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
broadcom such that monit only generates alerts if the processes are not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
cavium such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container such
that monit only generates alerts if the process is not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell-arm64 such that monit only generates alerts if the process is
not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell-armhf such that monit will generate alert if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
mellanox such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sycnd] Change the monit config file for syncd container such
that monit only generates alerts if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Change the monit config file for sflow container such
that monit only generates alerts if the process is not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Change the monit config file for telemetry container
such that monit only generates alerts if the processes are not running
for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Change the monit config file for database container
such that monit only generates alerts if the process is not running for
5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Use 4 spcess to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Use 4 spaces to replace 2 space in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-snmp] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Use 4 spaces to replace 2 spaces in monit config
file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on centec.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to repalce 2 spaces in the monit config file
on nephos.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Remove the trailing extra spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
As part of this commit, there are a few enhancements being
made for EM policy implementation: a) Introduced hysteresis
algorithm to prevent fan hunting b) Reading ASIC temperature
to make decision for fan speed.
As part of the PR# 3599, Workaround for the boot problem
from secondary bios was addressed. When the SONiC image is
upgraded, this resulted in creating multiple entries for
BOOTX64.EFI. To fix the problem, as part of this changeset,
introducing a check to see if there is already an UEFI entry
for BOOTX64.EFI and accordingly creating / skipping the UEFI
entry.
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
* [Mellanox]Update hw-mgmt to V7.0000.2308
sonic-linux-kernel should be updated accordingly with necessary patches uploaded.
* [sub-module]Advance submodule head for sonic-linux-kernel
This common utility would set next boot option as onie mode and
when reboot is triggered it would reboot the box into that specific onie mode.
Current support modes are rescue/install/uninstall
Fix the issue when an SFP module is plugged into a QSFP port via an adapter.
- How I did it
Originally the type of an SFP module is determined according to the SKU dictionary. However, it's possible that as SFP module is plugged into a QSFP port via an adapter. In this case, the EEPROM content will be parsed in the wrong format.
To address that we fetch the identifier value of an xSFP module and then get the type by parsing it.
- Updated buffers config;
- Set eth2 as CPU port;
- Added systemd service file to load bf_fpga.ko
Signed-off-by: Andriy Kokhan <akokhan@barefootnetworks.com>
* [sonic_platform.sfp] support get_transceiver_dom_threshold_info_dict
* [platform/sfp]qsfp threshold and beautify code
1. qsfp threshold: tx power
2. beautify code, removing some magic numbers
3. optimize get_present by only reading one byte.
* This method is used to update firmware components such as CPLD,FPGA,BIOS,SMF
* This uses ONIE firmware upgrade design to stage firmware update from NOS.
a) Copy latest firmware updater image to target running sonic.
b) Run “./fw-updater -u onie-firmware-x86_64-dellemc_s5200_c3538-r0.3.40.5.1-9.bin”.
c) This would automatically reboot ONIE into update mode and update firmware components to latest and reboot back to sonic without any user intervention.
Signed-off-by: Srideep Devireddy <srideep_devireddy@dell.com>
- optoe driver truncates invalid pages(ff) but sff driver doesn't truncate.so,the DOM related calculation made by sff8436 driver will show incorrect data.
- Few optics doesn't support DOM.
- SFP plugins currently returns None for unreadable pages and this'd throw the below mentioned error in sfpshow eeprom --dom.
Add the same mechanism I developed for the SwSS service in #2845 to the syncd service. However, in order to cause the SwSS service to also exit and restart in this situation, I developed a docker-wait-any program which the SwSS service uses to wait for either the swss or syncd containers to exit.
AS7326-56X and AS7726-56X use the same design so both devices have the same problem.
The detailed description below takes AS7326-56X as the example to explain.
Original implementation:
- In platform/broadcom/sonic-platform-modules-accton/as7326-56x/service/as7326-platform-handle_mac.service,
it executes the script file "accton_handle_idt.sh".
- In "accton_handle_idt.sh", it modifies the content of the script file "/etc/init.d/opennsl-modules"
to insert the lines to execute "idt_init.sh" before the command to load broadcom linux kernel module "linux-kernel-bde.ko".
- The script "idt_init.sh" cannot be executed at the first boot of SONiC after installing SONiC under ONIE. This is the reason why all of the ports does not work.
New implementation:
- Let "as7326-platform-handle_mac.service" execute "idt_init.sh".
- Change the content of "as7326-platform-handle_mac.service" to define the service type as "oneshot". Add the settings to ensure "as7326-platform-handle_mac.service" is executed before "opennsl-modules.service".
By setting the service type as "oneshot", it is guaranteed that "opennsl-modules.services" is started only when the forked process to execute the script file "idt_init.sh" is terminated
Signed-off-by: charlie_chen <charlie_chen@edge-core.com>
Implement Watchdog platform2.0 API for DellEMC S6100 platform.
- Added new file watchdog.py in sonic_platform directory.
- Enabled API support to Enable/disable watchdog.
Implement part of the Chassis and Fan related APIs.
- Chassis APIs
get_base_mac()
get_serial_number()
get_serial_number()
get_system_eeprom_info()
get_reboot_cause()
- Fan APIs
get_direction()
get_speed()
get_target_speed()
get_speed_tolerance()
set_speed()
set_status_led()
get_target_speed()
- Fan APIs base on Device API
get_name()
get_presence()
get_model()
get_serial()
get_status()
Signed-off-by: Wirut Getbamrung wgetbumr@celestica.com
* Preemphasis values for various optics
This patch adds the preemphasis values for the various supported
optics for qfx5210 platform
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
Fixed the fpga crash issue which we see in 15-20 mins time frame after onie-install. Accessing stale i2c transfer message buffer causes this crash. Te message buffer becomes stale due to race between i2c transfer and fpga interrupt handler.
This new state STATE_STOP will not be exposed for the wake up call till all the ISR of previous transfer is completed successfully.
[Makefile] Kill arm march docker service before every run to avoid stale entries
[Platform] Marvell - add dtb deb pkg
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
The following changes are done as part of this commit:
- Adding the system reboot handler
- Adding swizzle reset case for the reboot reason
- Workaround for the boot problem from Golden bios
- Adding the logging messages for platform scripts
- EEPROM parsing and library routines
[submodule]: update sonic-sairedis
1f4a1d7 2019-09-24 | Add warm boot support with removed/created port (#515) (HEAD, origin/master, origin/HEAD) [Kamil Cudnik]
59e530a 2019-09-20 | Add support for debug counters (#517) [Danny Allen]
1ed09e0 2019-09-20 | fully support bulk_remove in sairedis (#516) [Dong Zhang]
6cb1b31 2019-09-17 | Add support for port remove and port create (no warm boot) (#500) [Kamil Cudnik]
83d86ed 2019-09-17 | Fix c_str() in printf for string (#514) [Kamil Cudnik]
11b44b5 2019-09-16 | Advance SAI reference pointer to v1.5.0 (#509) [Wenda Ni]
38c6945 2019-09-14 | support sflow on virtual switch (#498) [Rakesh Datta]
e7d766e 2019-09-09 | Add acl counter match logic based on acl entry field (#511) [Kamil Cudnik]
58845ce 2019-09-06 | Add extra check for warm boot discovered RIDs (#502) [Kamil Cudnik]
b4893ef 2019-09-05 | [flex counter]: Lower the severity of log during rif counter support check (#504) [shikenghua]
b859344 2019-09-03 | fix found typo in new added syncMode related codes (#506) [Dong Zhang]
also update broadcom and mellanox SAI
* [sonic_platform]remove the handling of reset_sw_reset which indicates rebooted by software.
* [sonic_platform]Check "reset_sw_reset"
Also check reboot cause file "reset_sw_reset" which indicates the system was rebooted due to software requesting.
* Makefile: ARM kernel support from sonic-linux-kernel
* Fix for multiarch build docker spawn
Platform: Install the DTB deb for the platform
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
* Update driver and Add new platform API implementation for Inventec D6356
* Update Platform API (SFP)
* Update Platform API (QSFP)
* Update Platform API (FAN, THERMAL)
Signed-off-by: David Xiao <xiao.david@inventec.com>
*Currently get_firmware_version implementated by using chassis.get_firmware_version and chassis._component_name_list which are not supported in the latest sonic_platform_common, causing chassis broken. Update this part so that it aligns to the latest sonic_platform_common
*Support component API
The script sonic-gns3a.sh creates a GNS3 appliance flle, that points to a sonin-vs.img (SONiC Virtual Switch).
The appliance file (and sonic-vs.img file) can subsequently be imported into a GNS3 simulation environment.
Adjust the SDK makefiles so that it reflects the dependencies among libraries in SDK 4.3.2104.
This is a supplement of PR [Mellanox]Update SDK(4.3.2104), SAI-Implementation(1.15) and firmware 2162. It doesn't impact the sonic-mellanox.bin image but makes the future SDK-integration easier.
* Remove the divide by 4 operation to the under the hood SAI
This is to avoid the need and thus the confusion for application program to know
the mmu internal architecture
This change must have support from SAI change to reach the correct
config
Signed-off-by: Wenda <wenni@microsoft.com>
* Relegate the divide by 4 operation to the under the hood SAI for egress
lossless pool
Extend to 7060 and 6100
Signed-off-by: Wenda <wenni@microsoft.com>
* Add more TH/TH2 hwskus
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Update config test
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Add TH2 ingress lossy profile
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Move the divide by 4 operation to SAI internal
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* [bcm SAI] Upgrade Broadcom SAI to version 3.5.3.1-15
- Broadcom SAI 3.5 GA release 20190924.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
slave.mk: add SONIC_PLATFORM_API_PY2 as dependency of host
sonic_debian_extension.j2: install sonic_daemon_base and Mellanox-specific sonic_platform on host
mlnx-platform-api.mk: export mlnx_platform_api_py2_wheel_path for sonic_debian_extension.j2
sonic-daemon-base.mk: export daemon_base_py2_wheel_path for sonic_debian_extension.j2
daemon_base.py: hind unnecessary dependency of swss_common on host
Introduce a new "sflow" container (if ENABLE_SFLOW is set). The new docker will include:
hsflowd : host-sflow based daemon is the sFlow agent
psample : Built from libpsample repository. Useful in debugging sampled packets/groups.
sflowtool : Locally dump sflow samples (e.g. with a in-unit collector)
In case of SONiC-VS, enable psample & act_sample kernel modules.
VS' syncd needs iproute2=4.20.0-2~bpo9+1 & libcap2-bin=1:2.25-1 to support tc-sample
tc-syncd is provided as a convenience tool for debugging (e.g. tc-syncd filter show ...)
* Use dot1p to tc mapping for backend switches
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Do not write DSCP to TC mapping into CONFIG_DB or config_db.json for
storage switches
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Adding platform support for Juniper QFX5210
This switch has 64 QSFP28 (40G/100G) ports, 2 SFP+ (1G/10G) ports
on Broadcom Tomahawk II chipset. CPU used in QFX5210-64C-S is
Intel Broadwell-DE. The machine has Redundant and hot-swappable
Power Supply (1+1) and also has Redundant and hot swappable fans (3+1).
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
* [Juniper][QFX5210] Optoe driver for SFP management
This commit implements the following changes
- Moving to optoe driver for sfp management
- Removing the old sfp driver
- Updating the port-config.ini to add the index field
- Correction in sfputil.py to incorporate optoe driver
- Platform support for 'poweroff' command
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
Implemented remaining APIs in s6100,z9100,s6000
Removed soft link in s6100,s6000,z9100 and implemented seperately
Implemented get_transceiver_change_event in S6000
This switch has 64 QSFP28 (40G/100G) ports, 2 SFP+ (1G/10G) ports
on Broadcom Tomahawk II chipset. CPU used in QFX5210-64C-S is
Intel Broadwell-DE. The machine has Redundant and hot-swappable
Power Supply (1+1) and also has Redundant and hot swappable fans (3+1).
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
optimize SFP module operations and fix issues.
- split initialization of variant categories of devices and initialize each category of devices only when needed, so that unnecessary dependencies can be avoided.
- update watchdog logic, only initializing watchdog when referenced.
- support platform.py and enable to initialize variant devices on a host/docker basis
- update init so that sonic_platform can be imported as a whole.
- Improve smbus reliability for all platforms
- Delay processing of the reboot cause to reduce critical path
- Add support of get_change_event for PSUs
* Change psu driver to comfort to lm-sensors.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Duplicate fan attributes with naming conforming to lm-sensors.
Replace psu drivers.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Revise cpr_4011_4mxx.c to support lm-sensors.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [DELL][Z9100,S6100,S6000] Platform 2.0 SFP Changes
Added support in sfp.py file which will be generic. Send the eeprom path and sfp_control path from chassis.py
* fix sfpd initialize issue
* fix review comments
* rephrase the output log
* fix retry counter
* change the retry time to 10, means set max waiting time 1024s
* fix mlnx-sfpd init flow with new solution
* [mlnx-sfpd] address comments
1. wait for 5 seconds * 30 times, 150 seconds totally. use constant wait time for each retry.
2. use try/except structure so that error can be handled in a graceful way
* [mlnx-sfpd] wait 5 seconds after SDK_DAEMON_READY_FILE exists to make sure SDK is fully up.
* [mlnx-sfpd]simplify initialization by using deinitialize on initializing failure
This switch has 27 fiber ports, 4x25G, 20x10G , and 3x100G ports ports.
CPU: Intel ® Atom™ Processor C3508,1.6GHz
BMC: None
MAC: Broadcom BCM88470 (Qumran AX).
MISC: Support IEEE1588v2, hot-swappable PSU, hot-swappable fan tray.
But notice here, BCM88470 is not supported for SAI now.
So the syncd container is not running so far.
Signed-off-by: roy_lee <roy_lee@accton.com>
Add fan control for as7116-54x
Modify sfputil.py to support sfp insert and remove events for as7116-54x
Modify port_config.nps to set port default admin down
Modify port_config.ini for add speed attr
Code format optimization like remove newline
Modify buffers_defaults_t0 and t1, change ingress_lossless_pool mode from dynamic to static
Add nephos_dac.nps and nephos_opt.nps for support difference dac and fiber module
* [Makefile/slave docker] ARM arch doesn't support few packages
iproute2 is missing for ARM sonic-slave docker
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
Add platform support for delta ag9032v2a
CPU: Broadwell-DE
ASIC: BMC56870 with <100Gx32 + 10Gx1>
BMC: AST2520:
- What I did
add the new platform of delta ag9032v2a
- How I did it
1.provide the QSFP and SWPLD attributes and create the virtual buses of I2C
2. provide the port configuration
- How to verify it
1. psuutil.py
2. sfputil.py
3. bcmcd
- Known issue
The port LED is not ready. We noticed that BCM chip had the M0 FW initialization issue while bringing up SDK with "BRCM SAI ver: [3.5.2.3], OCP SAI ver: [1.4], SDK ver: [6.5.14]" and here is the information :
root@sonic:/home/admin# bcmcmd "M0 status"
M0 status
0:soc_iproc_data_send_wait: No response for msg 2
M0 FW is NOT Running
M0 FW Version is 0.0
Host FW Version is 1.0
Host and M0 FW Versions do not match!!!
Signed-off-by: hans-tseng <hans.tseng@deltaww.com>
I2c burst read may failed due to misoperation of ir3570a(A DC-to-DC converter IC).
As #2966, there are 3 more models have this symptom, as7326-56x, as7726-32x, and as9716-32d.
Also correct typo of naming on as7816-64x and as7716-32x.
Signed-off-by: roy_lee roy_lee@accton.com
What I did
Disabling i2c function of ir3570a which may failed i2c tranfer to others.
Close channel of mux after data transfered.
How I did it
Identify version of ir3570, if it's ir3570a, disable its alias i2c address.
Enable parameter of driver i2c_mux_pca954x to close channel on after every access.
How to verify it
Write 08 to offset 0xcf of systom eeprom and execute i2c block read.
It will return error.
plug-in several transceivers and run "show interfaces transceiver presence" and "sfputil show presence". You may see the different result. (But doing this requires updated xcvrd).
Signed-off-by: roy_lee <roy_lee@accton.com>
- What I did
Move the enabling of Systemd services from sonic_debian_extension to a new systemd generator
- How I did it
Create a new systemd generator to manually create symlinks to enable systemd services
Add rules/Makefile to build generator
Add services to be enabled to /etc/sonic/generated_services.conf to be read by the generator at boot time
Signed-off-by: Lawrence Lee <t-lale@microsoft.com>
* [Mellanox]refractor the sfp event change notification logic for new platform api
remove the standalong daemon which is in charge of polling sfp change event through sdk interface
and move the polling stuff to the event in the chassis daemon.
* rephase some comment
* fix typo in sfp_event.sfp_event.initialize
ARM Architecture support in SONIC
make configure platform=[ASIC_VENDOR_ARCH] PLATFORM_ARCH=[ARM_ARCH]
SONIC_ARCH: default amd64
armhf - arm32bit
arm64 - arm64bit
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
Added Reboot Reason for S6000 in platform 2.0
Fixed issue in process-reboot-cause
Added package uninstall code in platform de-init code for z9100, s6100
- How I did it
-> Added support for S6000 Reboot Reason
-> Added platform.py for all platforms
-> Verified show reboot-cause command with the code changes. Added UT logs with show reboot-cause
-> Modified process-reboot-cause service to start after pmon.service. In S6000, we have to wait for nvram to be loaded.
-> If reboot-cause service starts before pmon.service, show reboot-cause is showing incorrect reason.
-> Bug fix in process-reboot-cause file
- import sonic_platform
+ import sonic_platform.platform
* [as5712-54x]
Verified with index from 1.
Add qsfp_event() for command "show interaface trancerver".
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as6712-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7726-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7712-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5812-54x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5712-54x]
Update port-config with 1-based index.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5812-54x]
Somehow the service may block, use type=simple to work-around.
Add syslog function for monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7716-32x]
Update port-config with 1-based index.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7816-64x]
Update port-config with 1-based index.
Implement sfputil change_event.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7326-56x]
Update port-config with 1-based index.
Implement sfputil change_event.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Remove debug code.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7312-54x]
Update port-config with 1-based index and default port speed.
Signed-off-by: roy_lee <roy_lee@accton.com>
The following commit addresses the graceful unmounting of file
system and graceful shutdown of dockers before calling a
cold reboot which will cause a power cycle of SSD. This ensures
orderly shutdown and no corruption of files systems because
of the power cycle to SSD.
This commit will use the existing systemd-reboot service scripts
and override the configuration to do cold reboot for S6100 and
Z9100.
Unit tested the fix and graceful shutdown of file system and
dockers are done with cold reboot.
Signed-off-by: Harish Venkatraman <harish_venkatraman@dell.com>
* support new platform api, thermal and psu part
for psu, all APIs are supported.
for thermal, we support
get_temperature,
get_high_threshold
for the thermal sensors of cpu core, cpu pack, psu and sfp module
and get_temperature for the ambient thermal sensors around the asic, port, fan, comex and board.
* 1. address review comments
2. improve the handling of PSU inserting/removal
3. tolerance diverse psu thermal sensor file name conventions
* 1. adjust thermal code according to the latest version of hw-management
2. check power_good_status rather than whether file existing ahead of reading voltage, current and power of PSU
* [devices]: Add a new supported device DellEMC s5232f
* Switch Vendor: DellEMC
* Switch SKU: s5232F
* ASIC Vendor: Broadcom
* Swich ASIC: Trident3
* Port Configuration: 32x100G
* SONiC Image: sonic-broadcom.bin
* LED support for s5232f
* Changes Include ipmitool implementation for platform_sensors script is inclued in pmon startup
* Added 100G,25G,10G configruation ( 100G is default).
* s5232[device] PSU detecttion and default led state support
* Add driver and util for peripherals of as7312-54xs, most are copied from as7312-54s.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add default port speed and index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Update i2c addr of psus.
Add system logging for monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct syntax of module_dirs.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Validate sfputil after tested.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct the index of eeprom mapping.
Signed-off-by: roy_lee <roy_lee@accton.com>
Integrating official Mellanox SDK/FW release as a pre condition for getting new Mellanox SAI release with hash changes (inner field) and 3k VXLAN scale. As well as bug fix for Spectrum LP mode and Spectrum 2 PFC WD
Signed-off-by: Mykola Faryma <mykolaf@mellanox.com>
* fix the memory leak in on_pmpe. objects created via sx_api having convention new_<type_name> should be release explicitly via delete_<type_name>.
* avoid duplicate code.
Variables SFP_VLOT_OFFSET and QSFP_VLOT_OFFSET containing the typo are originally defined in repo sonic-platform-common. The typo has been fixed in PR #33. However, some Mellanox-specific code hasn't updated correspondingly, which results in xcvrd fail to start.
This PR updates the variable name in Mellanox-specific code correspondingly to fix that.
* new platform api, chassis part
* Inject mlnx mlx libs to platform monitor
* address the review comments
* remove some confusing naming.
* Adjust the minor cause to a more human-readable way when rebooted by firmware
* address review comments
* expose host dir /host/reboot-cause to pmon docker so that the reboot causing by user command can be identified
* 1. Revert "expose host dir /host/reboot-cause to pmon docker so that the reboot causing by user command can be identified"
Since the only hardware-causing reboot should be handled by get_reboot_cause and the logic of handling reboot cause is about to move to the host side, no need to mount this dir to pmon docker.
This reverts commit 3feb96869d.
2. adjust log output by using sonic_daemon_base.daemon_base.Logger.
3. remove the logic of verifying /host/reboot-cause/ files.
4. fix typo.
* implement get_firmware_version and adjust the interfaces regarding components' version retrieving according to the Azure/sonic-platform-common#34
* Switch Vendor: DellEMC
* Switch SKU: s5232F
* ASIC Vendor: Broadcom
* Swich ASIC: Trident3
* Port Configuration: 32x100G
* SONiC Image: sonic-broadcom.bin
* LED support for s5232f
* Changes Include ipmitool implementation for platform_sensors script is inclued in pmon startup
* Added 100G,25G,10G configruation ( 100G is default).
- What I did
Added Daemon to Log LPC bus degradation in Intel C2000 processor. Intel Rangeley C2000 processors with revision less than or equal to 2 have issue where LPC bus degrades over time in some processors. To identify the problem and to notify the issue, a daemon has been added which will log on encountering the issue.
- How I did it
Added a daemon which validates the CPLD scratch(0x102) and SMF scratch(0x202) registers by writing and reading values on regular polling intervals (300 seconds). If there is a discrepancy between read and write, a critical log will be thrown.
- How to verify it
The infra is verify by simulating the issue where between write and read, the value in register is modified and the log appearance is checked.
- Description for the changelog
Added Daemon to identify LPC bus degradation issue and notify using syslog in Dell S6100 and Z9100 platforms. This daemon will only run on processors with revision less than or equal to 2.
* Update sonic-quagga submodule
* Port some patches from sonic-quagga
* Fix Makefile
* Another patch
* Uncomment bgp test
* Downport Nikos's patch
* Add a patch to alleviate the vendor issue
* use patch instead of stg
- create a dockerfile-marcros.j2 file with all common operations
written as j2 macro
- use single dockerfile instruction for COPY and RUN commands
when possible to improve build time
- reorganize dockerfile instructions to make more cache friendly
(in case someday we will remove --no-cache to build docker images)
Signed-off-by: Stepan Blyschak <stepanb@mellanox.com>
- What I did
During boot/reload time, wait in a loop to check for bcm initialization.
Break the loop, once sdk is ready to process the 'bcmcmd' request (or) loop count reached the maximum value.
- How I did it
In the existing implementation during syncd start process will sleep for a fixed time (3 secs)
for sdk initialization to happen. But the time taken for sdk initialization is varying for different platforms.
To fix this issue, the syncd start process wait in a loop and check whether sdk is ready to process 'bcmcmd' command.
- How to verify it
Check for syncd process status and interface status.
Check for syslogs and no failures related to syncd should be present.
* [submodule] update sonic-linux-kernel
* update linux kernel version
* Fix many version strings
* update mellanox components (built with new kernel)
* [mlnx] add make files for SDK WJH libs
* Update arista driver submodule (#8)
Make the debian packaging point to a newer kernel version.
* Updated Makefile infrastructure to build debug images.
As a sample, platform/broadcom/docker-orchagent-brcm.mk is updated to add a docker-orchagent-brcm-dbg.gz target.
Now "BLDENV=stretch make target/docker-orchagent-brcm-dbg.gz" will build the debug image.
NOTE: If you don't specify NOSTRETcH=1, it implicitly calls "make stretch", which builds all stretch targets and that would include debug dockers too.
This debug image can be used in any linux box to inspect core file. If your module's external dependency can be suitably mocked, you my even manually run it inside.
"docker run -it --entrypoint=/bin/bash e47a8fb8ed38"
You may map the core file path to this docker run.
* Dropped the regular binary using DBG_PACKAGES and a small name change to help readability.
* Tweaked the changes to retain the existing behavior w.r.t INSTALL_DEBUG_TOOLS=y.
When this change ('building debug docker image transparently') is extended to all dockers, this flag would become redundant. Yet, there can be some test based use cases that rely on this flag.
Until after all the dockers gets their debug images by default and we switch all use cases of this flag to use the newly built debug images, we need to maintain the existing behavior.
* 1) slave.mk - Dropped unused Docker build args
2) Debug template builder: renamed build_dbg_j2.sh to build_debug_docker_j2.sh
3) Dropped insignifcant statement CMD from debug Docker file, as base docker has Entrypoint.
* Reverted some changes, per review comments.
"User, uid, guid, frr-uid & frr-guid" are required for all docker images, with exception of debug images.
* Get in sync with the new update that filters out dockers to be built (SONIC_STRETCH_DOCKERS_FOR_INSTALLERS) and build debug-dockers only for those to be built and debug target is available.
* Mkae a template for each target that can be shared by all platforms.
Where needed a platform entry can override the template.
This avoids duplication, hence easier to maintain.
* A small change, that can fit better with other targets too.
Just take the platform code and do the rest in template.
* Extended debug to all stretch based docker images
* 1) Combined all orchagent makefiles into one platform independent make under rules/docker-orchagent.mk
2) Extened debug image to all stretch dockers
* Changes per review comments:
1) Dropped LIBSAIREDIS_DBG from database, teamd, router-advertiser, telemetry, and platform-monitor docker*.mk files from _DBG_DEPENDS list
2) W.r.t docker make for syncd, moved DEPENDS from template to specific makefile and let the template has stuff that is applicable to all.
* 1) Corrected a copy/paste mistake
* Fixed a copy/paste bug
* The base syncd dockers follow a template, which defines the base docker as DOCKER_SYNCD_BASE instead of DOCKER_SYNCD_<platform code>. Fix the docker-syncd-<mlnx, bfn>.mk to use the new one.
[Yet to be tested locally]
* Fixed spelling mistake
* Enable build of dbg-sonic-broadcom.bin, which uses dbg-dockers in place of regular dockers, for dockers that build debug version. For dockers that do not build debug version, it uses the regular docker.
This debug bin is installable and usable in a DUT, just like a regular bin.
* Per review comments:
1) Share a single rule for final image for normal & debug flavors (e.g. sonic-broadcom.bin & sonic-broadcom-dbg.bin)
2) Put dbg as suffix in final image name.
3) Compared target/sonic-broadcom.bin.logs with & w/o fix to verify integrity of sonic-broadcom.bin
4) Compared target/sonic-broadcom.bin.logs with sonic-broadcom-dbg.bin.log for verification
This fix takes care of ONIE image only. The next PR will cover the rest.
The next PR, will also make debug image conditional with flag.
* Updated per comments.
Now that debug dockers are available, do not need a way to install debug symbols in regular dockers.
With this commit, when INSTALL_DEBUG_TOOLS=y is set, it builds debug dockers (for dockers that enable debug build) and the final image uses debug dockers. For dockers that do not enable debug build, regular dockers get used in the final image.
Note:
The debug dockers are explicitly named as <docker name>-dbg.gz. But there is no "-dbg" suffix for image.
Hence if you make two runs with and w/o INSTALL_DEBUG_TOOLS=y, you have complete set of regular dockers + debug dockers. But the image gets overwritten.
Hence if both regular & debug images are needed, make two runs, as one with INSTALL_DEBUG_TOOLS=y and one w/o. Make sure to copy/rename the final image, before making the second run.
These patches add support for the Broadcom XMC card (XLR/GTS). At this moment
only Tomahawk switch (BCM956960K) is supported. Add
device/broadcom/x86_64-bcm_xlr-r0 and
platform/broadcom/sonic-platform-modules-brcm-xlr-gts files
* Add new device accton_as5812_54x.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Rename 5812's config.bcm.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Change fan module to support lm-sensors.
Validate for thermal policy.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add bask reset and lpmode control of 6 QSFP ports.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Get currect duty of fan for comparing. Instead of by stored duty from previous iteration.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Roll back the mistakes to update mellanox submodules.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Rollback for misoperation on submodule platform/p4/SAI-P4-BM.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Change indexes of ports to start from 1, as them on the front panel.
Add low-power mode control of the transciever's eeprom, follows SFF-8436.
Signed-off-by: roy_lee <roy_lee@accton.com>
Since we move to FRR, we need to connect FRR with fpmsyncd via FPM.
Adding static routes is also required.
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
* Add boot0 support for the 7280CR3
* Add platform and plugins for 7280CR3
* Add port config for 7280CR3
* Add platform_reboot for 7280CR3
* Add support for 7280CR3-32D4 based on the 7280CR3-32P4
* Update arista driver submodules
- Introduce new 7280CR3-32P4
- Improve to the led plugin for OSFP
* [mlnx] fix mlnx-sfpd shutdown
Signed-off-by: Stepan Blyschak <stepanb@mellanox.com>
* fix type and handle only EINTR and EAGAIN errors from select
Signed-off-by: Stepan Blyschak <stepanb@mellanox.com>
* handle select.error as well during init/run
Signed-off-by: Stepan Blyschak <stepanb@mellanox.com>
- Update README.md
- Improve reboot cause reporting on all platform
- Refactor parts of the library toward sonic_platform API support
- Add abstraction for fans
- Export consistent sysfs entries for fan airflow direction
- Bootstrap python testing of the driver library.
- Fix miscellaneous bugs
* [platform/cel] Implement FAN APIs based on the new platform API
* [platform/cel] Move platform api to under device platform
* [platform/cel] Remove rule to build platform api python wheel
* catch signal SIGINT and SIGTERM to set all fans full-speed before end fan monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add fan_control monitor for as7816-64x.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Fix typo.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct typo and duty setting after verified.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [frr]: change frr as default sonic routing stack
* fix quagga configuration
* [vstest]: fix bgp test for frr
* [vstest]: skip bgp/test_invalid_nexthop.py for frr
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* Add bridge-utils to orchagent image
- Add vxlanmgrd to supervisorctl in docker -orchagent
Signed-off-by: Ze Gan zegan@microsoft.com
* Update submodule pointer for swss to include Vxlanmgrd changes
The base syncd dockers follow a template, which defines the base docker as DOCKER_SYNCD_BASE instead of DOCKER_SYNCD_. Fix the docker-syncd-<mlnx, bfn>.mk to use the new one.
This service (weekly) will let SSD firmware to do the garbage collection
after file-system deleted files. It could avoid slowness or
even READ-ONLY error due to SSD not being able to free the pages
even though the file system thinks there was a lot of space left.
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
Overall goal: Build debug images for every stretch docker.
An earlier PR (#2789) made the first cut, by transforming broadcom/orchagent to build target/docker-orhagent-dbg.gz.
Changes in this PR:
Made docker-orchagent build to be platform independent.
1.1) Created rules/docker_orchagent.mk
1.2) Removed platform//docker-orchagent-*.mk
1.3) Removed the corresponding entry from platform//rules.mk
Extended the debug docker image build to stretch based syncd dockers.
2.1) For now, only mellanox & barefoot are stretch based.
2.2) All the common variable definitions are put in one place platform/template/docker-syncd-base.mk
2.3) platform/[mellanox, bfn]/docker-syncd-[mlnx, bfn].mk are updated as detailed below.
2.3.1) Set platform code and include template base file
2.3.2) Add the dependencies & debug dependencies and any update over what base template offers.
Extended all stretch based non-platform dockers to build debug dockers too.
3.1) Affected are:
docker-database.mk,
docker-platform-monitor.mk,
docker-router-advertiser.mk,
docker-teamd.mk,
docker-telemetry.mk
Next: Build debug flavor of final images with regular dockers replaced with debug dockers where available.
* Add new device CIG CS6436-56P
* Delete minigraph.xml
It isn't necessary in the current system, just delete it
* Update qos.json.j2
* Update port_config.ini
Add the speed column. The cmd to show interface status as:
root@switch1:~# show interface status
Interface Lanes Speed MTU Alias Oper Admin Type Asym PFC
----------- --------------- ------- ----- ------------ ------ ------- ------ ----------
Ethernet0 8 25G 9100 Ethernet1/1 up up SFP N/A
Ethernet1 9 25G 9100 Ethernet2/1 up up SFP N/A
Ethernet2 10 25G 9100 Ethernet3/1 down down N/A N/A
Ethernet3 11 25G 9100 Ethernet4/1 down down N/A N/A
Ethernet4 12 25G 9100 Ethernet5/1 down down N/A N/A
Ethernet5 13 25G 9100 Ethernet6/1 down down N/A N/A
Ethernet6 14 25G 9100 Ethernet7/1 down down N/A N/A
Ethernet7 15 25G 9100 Ethernet8/1 down down N/A N/A
Ethernet8 16 25G 9100 Ethernet9/1 down down N/A N/A
Ethernet9 17 25G 9100 Ethernet10/1 down down N/A N/A
Ethernet10 18 25G 9100 Ethernet11/1 down down N/A N/A
Ethernet11 19 25G 9100 Ethernet12/1 down down N/A N/A
Ethernet12 20 25G 9100 Ethernet13/1 down down N/A N/A
Ethernet13 21 25G 9100 Ethernet14/1 down down N/A N/A
Ethernet14 22 25G 9100 Ethernet15/1 down down N/A N/A
Ethernet15 23 25G 9100 Ethernet16/1 down down N/A N/A
Ethernet16 32 25G 9100 Ethernet17/1 down down N/A N/A
Ethernet17 33 25G 9100 Ethernet18/1 down down N/A N/A
Ethernet18 34 25G 9100 Ethernet19/1 down down N/A N/A
Ethernet19 35 25G 9100 Ethernet20/1 down down N/A N/A
Ethernet20 40 25G 9100 Ethernet21/1 down down N/A N/A
Ethernet21 41 25G 9100 Ethernet22/1 down down N/A N/A
Ethernet22 42 25G 9100 Ethernet23/1 down down N/A N/A
Ethernet23 43 25G 9100 Ethernet24/1 down down N/A N/A
Ethernet24 48 25G 9100 Ethernet25/1 down down N/A N/A
Ethernet25 49 25G 9100 Ethernet26/1 down down N/A N/A
Ethernet26 50 25G 9100 Ethernet27/1 down down N/A N/A
Ethernet27 51 25G 9100 Ethernet28/1 down down N/A N/A
Ethernet28 56 25G 9100 Ethernet29/1 down down N/A N/A
Ethernet29 57 25G 9100 Ethernet30/1 down down N/A N/A
Ethernet30 58 25G 9100 Ethernet31/1 down down N/A N/A
Ethernet31 59 25G 9100 Ethernet32/1 down down N/A N/A
Ethernet32 64 25G 9100 Ethernet33/1 down down N/A N/A
Ethernet33 65 25G 9100 Ethernet34/1 down down N/A N/A
Ethernet34 66 25G 9100 Ethernet35/1 down down N/A N/A
Ethernet35 67 25G 9100 Ethernet36/1 down down N/A N/A
Ethernet36 68 25G 9100 Ethernet37/1 down down N/A N/A
Ethernet37 69 25G 9100 Ethernet38/1 down down N/A N/A
Ethernet38 70 25G 9100 Ethernet39/1 down down N/A N/A
Ethernet39 71 25G 9100 Ethernet40/1 down down N/A N/A
Ethernet40 72 25G 9100 Ethernet41/1 down down N/A N/A
Ethernet41 73 25G 9100 Ethernet42/1 down down N/A N/A
Ethernet42 74 25G 9100 Ethernet43/1 down down N/A N/A
Ethernet43 75 25G 9100 Ethernet44/1 down down N/A N/A
Ethernet44 76 25G 9100 Ethernet45/1 down down N/A N/A
Ethernet45 77 25G 9100 Ethernet46/1 down down N/A N/A
Ethernet46 78 25G 9100 Ethernet47/1 down down N/A N/A
Ethernet47 79 25G 9100 Ethernet48/1 down down N/A N/A
Ethernet48 84,85,86,87 100G 9100 Ethernet49/1 up up QSFP28 N/A
Ethernet49 80,81,82,83 100G 9100 Ethernet50/1 up up QSFP28 N/A
Ethernet50 92,93,94,95 100G 9100 Ethernet51/1 down down N/A N/A
Ethernet51 88,89,90,91 100G 9100 Ethernet52/1 down down N/A N/A
Ethernet52 108,109,110,111 100G 9100 Ethernet53/1 down down N/A N/A
Ethernet53 104,105,106,107 100G 9100 Ethernet54/1 down down N/A N/A
Ethernet54 116,117,118,119 100G 9100 Ethernet55/1 down down N/A N/A
Ethernet55 112,113,114,115 100G 9100 Ethernet56/1 down down N/A N/A
root@switch1:~#
* Updated Makefile infrastructure to build debug images.
As a sample, platform/broadcom/docker-orchagent-brcm.mk is updated to add a docker-orchagent-brcm-dbg.gz target.
Now "BLDENV=stretch make target/docker-orchagent-brcm-dbg.gz" will build the debug image.
This debug image can be used in any linux box to inspect core file. If your module's external dependency can be suitably mocked, you my even manually run it inside.
"docker run -it --entrypoint=/bin/bash e47a8fb8ed38"
You may map the core file path to this docker run.
* Dropped the regular binary using DBG_PACKAGES and a small name change to help readability.
* Tweaked the changes to retain the existing behavior w.r.t INSTALL_DEBUG_TOOLS=y.
When this change ('building debug docker image transparently') is extended to all dockers, this flag would become redundant. Yet, there can be some test based use cases that rely on this flag.
Until after all the dockers gets their debug images by default and we switch all use cases of this flag to use the newly built debug images, we need to maintain the existing behavior.
