Why I did it
Update the sonic-swss submodule for the 202012 branch. The following is the new commit in the submodule.
c1cb2ca [202012] Backport SAI failure handling to 202012 branch (#1880)
How I did it
Update the sonic-swss submodule pointer for the 202012 branch.
with state of tdport from previous warm-reboot.
In case LAG was down before reboot, lacp->wr is not cleared.
In lacp_event_watch_port_flush_data we incremented nr_of_tdports and add
tdport to lacp->wr.state. In case lacp->wr.state already had this tdport
we do not set new state for tdport but appened a new item in
lacp->wr.state. In case we preformed warm-reboot and PortChannel member
was down, after reboot PortChannel member became up next warm-reboot
will initialize teamd with PortChannel member in down state.
Fix this issue by calling stop_wr_mode() when LAG was down. This was probably intended but missed.
#### Why I did it
To fix an issue seen in warm-reboot-sad test cases.
#### How I did it
I fixed it in SONiC libteam patch that adds warm-reboot support. Details in commit description.
#### How to verify it
Run warm-reboot-sad test on t0-56 topology.
ef4b3ec [Y-Cable] add the definition inside setup.py to include sonic_y_cable.credo as a package (#211)
7d81488 [Y-Cable][Credo] Credo implementation of YCable class which inherits from YCableBase required for Y-Cable API's in sonic-platform-daemons (#203)
3efb093 [sonic_y_cable] add abstract class YCableBase required for Y-cable API support for multiple vendors (#186)
Signed-off-by: vaibhav-dahiya <vdahiya@microsoft.com>
caclmgrd: monitor mux_cable_table in state_db to update dhcp acl
- if the state changes to 'standby', add acl to block dhcp packets based on ingress interfaces
- if the state changes to 'active', delete acl
- if the state changes to 'unknown', also delete acl to avoid potential disconnect
- both addition and deletion follow checking the existence of the rules
The change has been verified on a virtual switch based testbed.
Port to 202012 branch from #8222
enable automated test suites to selectively run relevant tests ( or not run tests ) based upon a new port_type identifier in hwsku.json
How I did it
Modified the valid optional fields in validity check for hwsku.json per recommendation from Joe in
https://github.com/Azure/sonic-mgmt/pull/2654/files
Co-authored-by: Carl Keene <keene@nokia.com>
Signed-off-by: Rajkumar Pennadam Ramamoorthy rpennadamram@marvell.com
Why I did it
Install sonic image from ONIE. Once system is up, execute "config reload" command.
Root cause is that "determine-reboot-cause.service" was in failed state.
root@sonic:/host/reboot-cause# systemctl list-units --failed
UNIT LOAD ACTIVE SUB DESCRIPTION
● determine-reboot-cause.service loaded failed failed Reboot cause determination service
How I did it
Fixed the issue by setting default reason to "REBOOT_CAUSE_UNKNOWN" instead of "None".
How to verify it
Check " determine-reboot-cause.service' loaded successfully post image installation from ONIE.
Verify "reboot-cause.txt" file is created and config reload succeeds.
#### Why I did it
hostcfgd is starting at the same time as 'create_switch' method is called on orchagent process.
This introduce a degradation on the function execution time which eventually cause the fast-boot flow and a boot scenario in general to run slower (~6 seconds).
This change will delay the start time of this daemon.
90 seconds determined as the maximum allowed downtime for control plane to come back up on fast-boot flow.
#### How I did it
Add a timer for hostcfgd service in order to delay the startup of this service.
#### How to verify it
Install an image with this change and observe the daemon start 90 seconds after the system boot.
* 41dfaad 2021-08-02 | Bridge mac setting, fix statedb time format (#1844) (HEAD, origin/202012) [Prince Sunny]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* Update default cable len to 0m for TD2 (#8298)
* Update sonic-cfggen tests with the correct cable len
Signed-off-by: Neetha John <nejo@microsoft.com>
As part of the buffer reclamation efforts for TD2, setting the default cable len to 0m which means unused ports will have a cable len of 0m.
Why I did it
To align with the changes in Azure/sonic-swss#1830
How to verify it
- With the default cable len set to 0m and the associated changes in swss, CABLE_LENGTH table had '0m' set for unused ports and accordingly more space was reserved for the shared pool
- Cfggen tests passed with the cable len update
To include following changes:
* d84a8cc 2021-08-05 | [fast-reboot] revert the change of disabling counter polling before fast-reboot (#1744) (HEAD -> 202012, github/202012) [Ying Xie]
* e900bc5 2021-08-04 | Add script null_route_helper (#1718) [bingwang-ms]
* 85f14e1 2021-08-02 | disk_check updates: (#1736) [Renuka Manavalan]
* d68ac1c 2021-05-27 | [console][show] Force refresh all lines status during show line (#1641) [Blueve]
* a0e417f 2021-04-25 | [console] Display success message after line cleared (#1579) [Blueve]
* 0c6bb27 2021-04-07 | [console] Include Flow Control status in show line result (#1549) [Blueve]
I have been seeing intermittent (~40%) build failures with the same error described in PR https://github.com/Azure/sonic-buildimage/pull/6592, even with that fix present
```
/usr/bin/ld: mibgroup/ip-forward-mib/ipCidrRouteTable/.libs/ipCidrRouteTable_interface.o: file not recognized: file truncated
...
libtool: error: 'mibgroup/ip-forward-mib/inetCidrRouteTable/inetCidrRouteTable_interface.lo' is not a valid libtool object
make[5]: *** [Makefile:1020: libnetsnmpmibs.la] Error 1
make[5]: *** Waiting for unfinished jobs....
```
#### How I did it
Use `-j1` for the libsnmp build regardless of the value of `$(MULTIARCH_QEMU_ENVIRON)`
#### How to verify it
Performed 10 builds of the libsnmp target (`target/debs/buster/libsnmp-base_5.7.3+dfsg-5_all.deb`) with and without this change. Without the change, hit the error 40% of the time. With the change did not see the error at all
Signed-off-by: Justin Sherman <jusherma@cisco.com>
Update submodule for swss
f54b7d0b [Dynamic Buffer Calc][202012]Bug fix: Don't create lossless buffer profile for active ports without speed configured (Azure/sonic-swss#1820)
ac7f5cff Td2: Reclaim buffer from unused ports (Azure/sonic-swss#1830)
04105a4b [debugcounterorch] check if counter type is supported before querying (Azure/sonic-swss#1789)
a67d8af6 [202012][portsorch] fix errors when moving port from one lag to another. (Azure/sonic-swss#1819)
This PR updates the following commits
a9606fb [show] fix show muxcable metrics <port> for sorted output (#1731)
7355016 [minigraph][port_config] Use imported config.main and add conditional patch (#1728)
cc1d6e4 [configlet] Python3 compatible syntax for extracting a key from the dict (#1721)
Signed-off-by: vaibhav-dahiya <vdahiya@microsoft.com>
It can be that service is not enabled but UnitFilePreset=enabled (case
for Application Extension):
```
Loaded: loaded (/lib/systemd/system/cpu-report.service; disabled; vendor preset: enabled)
```
This makes existing logic skip enabling the service.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
Backport #7944
#### Why I did it
The current logic generates 'VLAN_SUB_INTERFACE' table if the device type is backend and cluster name contains 'str'. This is not a reliable method to determine a storage backend device
#### How I did it
Updated the logic to generate 'VLAN_SUB_INTERFACE' table if any of the following conditions hold true
1. device is of type backend and ResourceType attribute is None
2. device is of type backend and ResourceType attribute contains "Storage"
3. device is of type backend and graph contains "Subinterface" section
Also updated the logic to set "is_storage_device" to True
1. for Backend, if any of the above conditions hold true
2. for Frontend, if ResourceType attribute contains "Storage"
#### How to verify it
Added new tests to verify the code changes and built sonic_config_engine-1.0-py3-none-any.whl successfully
Update:
> 2ca493b 2021-07-13 create sniffer folder if not exist (Azure/sonic-utilities#1659)
> 1695104 2021-07-07 [show priority-group drop counters] Remove backup with cached PG drop counters after 'config reload' (Azure/sonic-utilities#1679)
> e99a3c5 2021-07-07 [show][config] support for interface alias for muxcable commands (Azure/sonic-utilities#1699)
Currently hostcfgd is implemented in a way each feature which is enabled/disabled triggering execution of systemctl enable/unmask commands which eventually trigger 'systemctl daemon-reload' command.
Each call like this cost 0.6s and overall add a overhead of ~12 seconds of CPU time.
This change will verify the desired state of a feature and the current state of this feature on systemd and trigger a system call only when must.
What is changed: Check each feature status on systemd before executing a system call to enable and reload the systemctl daemon.
How to verify: Build an image with this change and observe less system calls are executed.
Why I did it
Static route configuration should not depend on BGP_ASN. Remove the dependency on BGP_ASN for StaticRouteMgr.
Fix#8027
How I did it
Check if BGP_ASN field before configuring static route redistribution and wait until BGP_ASN is available to enable static route redistribution.
How to verify it
Add unit test to cover the scenario and verify the functionality on a virtual switch.
Update submodule for sonic-utilities to include the following PR:
[202012] [pfcwd] Fix the return code in invalid case (#1698)
Signed-off-by: Dror Prital <drorp@nvidia.com>
Advance submodule head for sonic-swss on 202012
bb383be2 [Dynamic Buffer Calc][Mellanox] Bug fixes and enhancements for the lua plugins for buffer pool calculation and headroom checking (Azure/sonic-swss#1781)
f949dfe9 [Dynamic Buffer Calc] Avoid creating lossy PG for admin down ports during initialization (Azure/sonic-swss#1776)
def0a914 Fix config prompt question issue (Azure/sonic-swss#1799)
21f97506 [ci]: Merge azure pipelines from master to 202012 branch (Azure/sonic-swss#1764)
a83a2a42 [vstest]: add dvs_route fixture
849bdf9c [Mux] Add support for mux metrics to State DB (Azure/sonic-swss#1757)
386de717 [qosorch] Dot1p map list initialization fix (Azure/sonic-swss#1746)
f99abdca [sub intf] Port object reference count update (Azure/sonic-swss#1712)
4a00042d [vstest/nhg]: use dvs_route fixture to make test_nhg more robust
Signed-off-by: Stephen Sun <stephens@nvidia.com>
Update submodule for sonic-utilities to include the following PRs:
80b7b54 Pcieutil to load the platform api first instead of using common api (sonic-utilities#1672)
3d5e93d [Mellanox] Update mellanox dump generation to include SDK dumps (sonic-utilities#1640)
a805efc [ci]: Fix config prompt question issue (sonic-utilities#1693)
33c6d79 [vnet_route_check] Fix logic for getting VNET routes from ASIC DB (sonic-utilities#1653)
Update submodule for sonic-sairedis to include the following PRs:
74b5808 [Mellanox] Update mellanoxs dump generation to include SDK dumps (sonic-sairedis#833)
5ff9305 Fix azure-pipelines branch reference error, change master to 202012 (sonic-sairedis#834)
#### Why I did it
To ensure any environment variables which are configured in the build/test environment do not influence the behavior of sonic-py-common during unit tests. For example, variables which might be set by continuous integration pipelines.
#### How I did it
Add class-scoped pytest fixture to `TestDeviceInfo` class which stashes the current environment variables, clears them and yields. Once all the test cases in the class finish, the fixture will restore the original environment variables.
Also remove unnecessary unittest-style setup and teardown functions from interface_test.py
A recent version of contextlib2 (https://pypi.org/project/contextlib2/21.6.0/#history) has broken Python2 compatibility,
so the version picked up by netaddr when using Python2 must be specified, or else builds fail
Co-authored-by: Tom Zhu <tom.zhu@metaswitch.com>
Update submodule for sonic-utilities to include the following PRs:
Make the soft-reboot available in the SONiC image on master (#1681)
[config]: Update environment file during config reload (#1673)
Enable pr checker form 202012 (#1649)
[config] support for configuring muxcable to manual mode of operation (#1642)
[config] Fix config int add incorrect ip (#1414)
Signed-off-by: Dror Prital <drorp@nvidia.com>
b0dad8c Add to check pcie configuration revision to get the right configuration. (#195)
f66ffc3 [eeprom_tlv_info] Optimize EEPROM data process by using visitor pattern (#193)
* Revert "fix"
This reverts commit 93585b0a0a.
* Revert "Version control git (#6562)"
This reverts commit 52b87753db.
* Revert "Revert "[files/build/versions]: support reproduceable build for git (#5774)""
This reverts commit 1cb8daf585.
* Revert "[files/build/versions]: support reproduceable build for git (#5774)"
This reverts commit 547aa9b2c7.
Add PG_DROP yang model and add check this field in unit test for yang model
How to verify it
Firstly try to do DPB (2x50G) for Ethernet0 port:
sudo config interface breakout Ethernet0 2x50G -f
After that try to do DPB (1x100G[40G]) for Ethernet0 port:
sudo config interface breakout Ethernet0 1x100G[40G] -f
Both commands should work correctly.
Signed-off-by: Mykola Gerasymenko <mykolax.gerasymenko@intel.com>
#### Why I did it
Recently, the build started failing with messages like
```
2021-06-16T16:55:02.8675603Z tests/hostcfgd/hostcfgd_test.py:5: in <module>
2021-06-16T16:55:02.8676208Z from parameterized import parameterized
2021-06-16T16:55:02.8677145Z E ModuleNotFoundError: No module named 'parameterized'
```
Unit tests for hostcfgd depend on the `parameterized` Python package, but it was never added as a dependency to the setup.py file. This dependency was added ~3 months ago. I'm not sure why we only started seeing this failure recently.
#### How I did it
Add 'parameterized' package as a test dependency in setup.py for sonic-host-services package
Why I did it
The SONiC switches get their docker images from local repo, populated during install with container images pre-built into SONiC FW. With the introduction of kubernetes, new docker images available in remote repo could be deployed. This requires dockerd to be able to pull images from remote repo.
Depending on the Switch network domain & config, it may or may not be able to reach the remote repo. In the case where remote repo is unreachable, we could potentially make Kubernetes server to also act as http-proxy.
How I did it
When admin explicitly enables, the kubernetes-server could be configured as docker-proxy. But any update to docker-proxy has to be via service-conf file environment variable, implying a "service restart docker" is required. But restart of dockerd is vey expensive, as it would restarts all dockers, including database docker.
To avoid dockerd restart, pre-configure an http_proxy using an unused IP. When k8s server is enabled to act as http-proxy, an IP table entry would be created to direct all traffic to the configured-unused-proxy-ip to the kubernetes-master IP. This way any update to Kubernetes master config would be just manipulating IPTables, which will be transparent to all modules, until dockerd needs to download from remote repo.
How to verify it
Configure a switch such that image repo is unreachable
Pre-configure dockerd with http_proxy.conf using an unused IP (e.g. 172.16.1.1)
Update ctrmgrd.service to invoke ctrmgrd.py with "-p" option.
Configure a k8s server, and deploy an image for feature with set_owner="kube"
Check if switch could successfully download the image or not.
Why I did it
Enable redistribution of static routes
How I did it
Enable redistribution of static routes when the first route is added to STATIC_ROUTE table of Config_DB and disable the redistribution when the last route is removed from STATIC_ROUTE table.
Advance submodule head for sonic-utilities
b894c5b5 Fix build test failure caused by error module name (Azure/sonic-utilities#1662)
5a7c06a0 [config]][tacacs+] Change tacacs+ minimum timeout value base on spec (Azure/sonic-utilities#1631)
080a689c [202012] [db_migrator] fix old 1911 feature config migration to a new one. (Azure/sonic-utilities#1636)
43fff88c Change to use rvtysh when calling the show commands (Azure/sonic-utilities#1646)
88a823f0 [db_migrator][Mellanox] Update Mellanox buffer migrator with 2km-cable supported (Azure/sonic-utilities#1564)
d096ff78 [config]Static routes to config_db (1534)
a68d8d09 route_check: Updates (Azure/sonic-utilities#1645)
Includes below comments:
```
fcf7cdc [patch] add patch "net: sch_generic: fix the missing new qdisc assignment bug" (#213)
```
#### Why I did it
To bring the fix "net: sch_generic: fix the missing new qdisc assignment bug".
#### How I did it
Updated submodule.
#### How to verify it
Build and run.
Verify that flapping a LAG member port does not lead to this member beeing stuck in disabled state.
Why I did it
ndppd by default reads /proc/net/ipv6_route ever 30 seconds. Since T1s advertise so many routes to ToRs, this file is extremely large, and reading it causes ndppd's CPU usage to spike every 30 seconds
How I did it
Increase the delay for reading this file to the maximum possible value (max integer value), which will result in CPU spikes every ~24 days instead of every 30 seconds
How to verify it
Start ndppd with the new config file, confirm that no CPU spikes are seen except at startup
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
Why I did it
The current code skips parsing bandwidth for DeviceMgmtLinks. We have a use case to set the speed for these type of links based on the bandwidth attribute in the minigraph
How to verify it
Ran sonic-cfggen on a minigraph and verified that interface of type DeviceMgmtLink has speed set in the PORT table from the bandwidth attribute in the minigraph
sonic-utilities:
* 8b98d45 2021-05-25 | [show] support for show muxcable firmware version of only active banks (#1629) (HEAD -> 202012) [vdahiya12]
* afd0975 2021-05-20 | [show] add support for muxcable metrics (#1615) [vdahiya12]
sonic-swss
* 7611df5 2021-05-27 | [tunneldecaporch] Set default MTU for the overlay loopback interface (#1756) (HEAD -> 202012) [Volodymyr Samotiy]
* 22fbb5c 2021-05-27 | [202012] Resolve neighbor when nexthop does not exist (#1759) (github/202012) [Shi Su]
* ec7710c 2021-05-27 | [Bulk mode] Limit the size of bulker (#1760) [Shi Su]
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
Why I did it
k8s handles in lower case, so the code ensures that it uses hostname in all lower case
How I did it
Wrapper for device_info.get_hostname that returns in lower case. This wrapper is used in all places that require hostname to use in kubectl commands.
How to verify it
Device joins successfully.
Why I did it
Currently, there is a bug in the ntp.conf jinja2 template where it will ignore the src_intf directive in CONFIG_DB if there are multiple IP addresses associated with an interface. This code change fixes that bug and allows the template to select the correct source interface for NTP.
How I did it
I did this by modifying the macro in ntp.conf.j2 which determines if there is an ip address associated with an interface to set a state variable when it detects a valid interface entry in CONFIG_DB instead of outputting "true" directly (which could result in multiple "trues" outputted for interfaces with multiple valid IP addresses).
How to verify it
Add two ipv4 addresses to an interface in SONiC
Add the following configuration to config_db.json
{
"NTP": {
"global": {
"src_intf": "Ethernet1"
}
}
}
Replace Ethernet1 with the interface name of the one you assigned the IP addresses to.
Run sudo config reload -y
Open /etc/ntp.conf and verify that the following line exists
...
interface listen Ethernet1
...
The interface specified should be the one set in the previous steps.
Description for the changelog
[ntp] Fix ntp.conf template to allow setting of source port in CONFIG_DB
Signed-off-by: Neetha John nejo@microsoft.comFixes#7531
Why I did it
To enable bgp sessions to be established over subinterfaces
How I did it
Listen to VLAN_SUB_INTERFACE table in config db
How to verify it
Bgp sessions were established successfully over subinterface
When FECDisabled is set to true in minigraph.py, push 'fec' 'none' explicitly to config_db. When 'fec' is defined in port_config.ini do not override it with 'rs' for 100G
Backport of #7667 to 202012 branch.
Why I did it
Skip to use the web proxy when the packages have been in the proxy server.
For sai packages or the other packages, we will upload the the proxy server directly, the reproducible will skip to check the site, not necessary to change the version files.
Why I did it
Add bgpcfgd support for static routes.
How I did it
Add bgpcfgd support to subscribe changes in STATIC_ROUTE table in CONFIG_DB and program via vtysh. The key of STATIC_ROUTE table is formatted as STATIC_ROUTE|vrf|ip_prefix, while the vrf is optional. If would be treated the same as "default" if no vrf is given.
Add unit tests.
Make sure Everflow always gets classified as Mirror table and not as Control Plane on multi-asic platforms.
Why I did:
In Multi-asic platforms we generate Everflow acl table data from minigraph for both host and namespace.
It is possible in multi-asic minigraph if there are no external port-channel (Only Router Port IP Interface) then Everflow table will have no binded interface in host and will gets classified as Control Plane ACL while in namespace gets classified as Mirror Table.
For ACL Rule generation we read global db as source of truth for acl table information and so for everflow rule generation if tables gets classified as Control plane we can generate rules with invalid action causing orchagent to throw runtime error.
How I did:
If the table is attach to erspan interface in minigraph then it always gets classified as mirror table.
1. Made the command next-hop-self force only applicable on back-end asic bgp. This is done so that BGPL iBGP session running on backend can send e-BGP learn nexthop. Back end asic FRR is able to recursively resolve the eBGP nexthop in its routing table since it knows about all the connected routes advertise from front end asic.
2. Made all front-end asic bgp use global loopback ip (Loopback0) as router id and back end asic bgp use Loopbacl4096 as ruter-id and originator id for Route-Reflector. This is done so that routes learnt by external peer do not see Loopback4096 as router id in show ip bgp <route-prerfix> output.
3. To handle above change need to pass Loopback4096 from BGP manager for jinja2 template generation. This was missing and this change/fix is needed for this also https://github.com/Azure/sonic-buildimage/blob/master/dockers/docker-fpm-frr/frr/bgpd/templates/dynamic/instance.conf.j2#L27
4. Enhancement to add mult_asic specific bgpd template generation unit test cases.
Enable BBR config allowas-in 1 for internal peers
Why I did:
To advertise BBR routes learnt via e-BGP peer in one asic/namespace to another iBGP asic/namespace via Route Reflector.
What I did:-
For multi-asic platforms added iptable v4 rule to communicate on docker bridge ip
For multi-asic platforms extend iptable v4 rule for iptable v6 also
For multi-asic program made all internal rules applicable for all protocols (not filter based on tcp/udp). This is done to be consistent same as local host rule
For multi-asic platforms made nat rule (to forward traffic from namespace to host) generic for all protocols and also use Source IP if present for matching
https://github.com/mbj4668/pyang/blob/master/pyang/repository.py#L93 throws an exception with pip 21.1
add ietf yang model explicitly to the build process fix the test failure.
tests/test_sonic_yang_models.py .F [ 66%]
tests/yang_model_tests/test_yang_model.py . [100%]
Failed: pyang -f tree ./yang-models/*.yang > ./yang-models/sonic_yang_tree
----------------------------- Captured stderr call -----------------------------
./yang-models/sonic-acl.yang:8: error: module "ietf-inet-types" not found in search path
./yang-models/sonic-device_metadata.yang:8: error: module "ietf-yang-types" not found in search path
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Previously, a brief sleep was necessary in order to get Python threads to progress. The root cause of this has since been found and fixed in sonic-swss-common: Azure/sonic-swss-common#477. The submodule was updated here, so we can now safely remove this sleep.
This PR should also be cherry-picked to the 202012 branch once the submodule is updated there to also include the fix.
* [202012] Add SOC property to enable AN/LT on some platforms
Why I did it
To enable autonegotiation/link training on some Broadcom-based platforms (Arista 7060CX, 7260CX3, 7050cx3, Celestica DX010)
How I did it
Add appropriate SOC property for enabling the feature to the Broadcom config files of appropriate platforms
Also convert line endings to UNIX format for one Celestica file
* Add 'phy_an_lt_msft' to BCM config file permitted list
68ea9efc Add pg-drop script to sonic filesystem (#1583)
b216bf0a Fixing serial number read to get from DB if it is populated (#1580)
fa7230c6 Handle the new db version which mellanox_buffer_migrator isn't interested (#1566)
Signed-off-by: Stephen Sun <stephens@nvidia.com>
Includes below commits:
```
3f8bc52 2021-05-05 | Relax the install_requires, no need to exact version as long as there are no broken changes with future versions (#1530) (#1592) [Qi Luo]
```
* [202012][swss/swss-common/utilities/kernel] Update submodule
sonic-swss:
- [Monitor Vlan] Fix a typo in hostif (#1722)
- Update pool sizes during initialization from timer only (#1708)
- [SflowMgr] SamplingRate Update by Speed Change Added (#1721)
sonic-swss-common:
- [swss-common] Add MUX Metrics Table (#482)
- [azp] Purge swss before installing the newly built deb package (#472)
sonic-utilities:
- disk_check: Check & mount RO as RW using tmpfs (#1569)
- No more IP validation as it is more likely a URL (#1555)
- Stop PMON docker before cold and soft reboots (#1514)
- Add soft-reboot reboot type (#1453)
- [acl] Use a list instead of a comma-separated string for ACL port list (#1519)
- sonic-installer: fix py3 issues in bootloader.aboot (#1553)
- Fix unsupported fs.squashfs extraction in sonic-installer (#1366)
- [show][config] cli support for firmware upgrade on Y-Cable (#1528) (#1558)
sonic-linux-kernel:
- [Mellanox] backport kernel patches for hw-management 7.0100.2303 (#211)
Signed-off-by: Danny Allen <daall@microsoft.com>
* Update utilities w/ build fix
- Support compile sonic arm image on arm server. If arm image compiling is executed on arm server instead of using qemu mode on x86 server, compile time can be saved significantly.
- Add kernel argument systemd.unified_cgroup_hierarchy=0 for upgrade systemd to version 247, according to #7228
- rename multiarch docker to sonic-slave-${distro}-march-${arch}
Co-authored-by: Xianghong Gu <xgu@centecnetworks.com>
Co-authored-by: Shi Lei <shil@centecnetworks.com>
adf5ab58 [vstest/subintf] Add vs test case to validate processing sequence of APPL DB keys (#1663)
8a732726 [intfsorch] Create subport with the entry contains necessary attributes (#1650)
7ba813b2 [vstest/subintf] Update vs tests to validate physical port host interface vlan tag attribute (#1634)
ed32e333 [portsorch] Configure hostif tagging for subports (#1573)
b5209c43 Handle IPv6 and ECMP routes to be programmed to ASIC (#1711)
515cc1a7 [Dynamic buffer calc][Mellanox] Fix bug: buffer over subscription in buffer pool size calculation (#1706)
0ad524b2 [202012] Allowing the first time FEC and AN configuration to be pushed to SAI (#1710)
Signed-off-by: Stephen Sun <stephens@nvidia.com>
1) Dropped non-required IP update in admin.conf, as all masters use VIP only (#7288)
2) Don't clear VERSION during stop, as it would overwrite new version pending to go.
3) subprocess, get return value from proc and do not imply with presence of data in stderr.
