Why I did it
Support to build armhf/arm64 platforms on arm based system without qemu simulator.
When building the armhf/arm64 on arm based system, it is not necessary to use qemu simulator.
How I did it
Build armhf on armhf system, or build arm64 on arm64 system, by default, qemu simulator will not be used.
When building armhf on arm64, and you have enabled armhf docker, then it will build images without simulator automatically. It is based how the docker service is run.
Docker base image change:
For amd64, change from debian:to amd64/debian:
For arm64, change from multiarch/debian-debootstrap:arm64- to arm64v8/debian:
For armhf, change from multiarch/debian-debootstrap:armhf- to arm32v7/debian:
See https://github.com/docker-library/official-images#architectures-other-than-amd64
The mapping relations:
arm32v6 --- armel
arm32v7 --- armhf
arm64v8 --- arm64
Docker image armhf deprecated info: https://hub.docker.com/r/armhf/debian, using arm32v7 instead.
For multiasic, the back end asics use ip addresss of Loopback4096 for BGP router id. In VOQ multi-asic chassis there are no back end asics. All the asics are front end and the iBGP connections are established via Ethernet-IB of asics. Since these asics are not designated as BackEnd, the ip address of interface Loopback0 is used as BGP router id. Since the ip address of Loopback0 is same for all the asics in the line card, same router id is used for voq iBGP configurations and hence the iBGP connections are not established. Changes are done to fix this
Why I did it
There are scenarios that End-of-RIB comes from a part of the peers arrives after reconciliation. In such scenarios, if the route selection deferral timer has the default value of 360 seconds, FRR would not set up routes and all routes would be removed after reconciliation. This PR reduces the route selection deferral timer so that at least routes to parts of the peers get restored at the point of reconciliation.
Fix#7488
How I did it
Reduce route selection deferral timer for bgp graceful restart to 15 seconds.
Why I did it
the motivation for this PR is to add retry_call to several test cases in the community, for example, the following cases:
test_show_platform_fanstatus_mocked
test_show_platform_temperature_mocked
are executing a command once and comparing the output to the expected mock data,
sometimes differences between the mock and the actual are causing the tests to fail.
retry will make these tests more stable.
retry will also be more efficient than sleep which will cause the tests to run longer because sometimes it is not necessary to sleep all that time, retry will only run a function only until it passed.
How I did it
added retry to the docker file
How to verify it
I run the tests with retry on the docker after installing the retry package
Signed-off-by: Sharon Lutati <slutati@nvidia.com>
Why I did it
Currently SONiC use the 'isc-dhcp-relay' package to allow DHCP relay functionality on IPv4 networks only.
This will allow the IPv6 functionality along the IPv4 type.
How I did it
Edit supervisord template to start DHCPv6 instances when configured to do so on Config DB.
Align cfg unit test to the new change.
Add DHCPv6 relay minigraph parsing support and a suitable t0 topology xml file for UT.
How to verify it
Configure DHCPv6 agents as described on the feature HLD: Azure/SONiC#765
Test it with real client/server with IPv6 or use the dedicated automatic test: Azure/sonic-mgmt#3565
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
* Split docker-dhcp-relay.supervisord.conf.j2 template into several files for easier code maintenance
- Why I did it
Make DHCP relay docker an extension. DHCP relay now carries dhcp relay commands CLI plugin and has a complete manifest.
It is installed as extension if INCLUDE_DHCP_REALY is set to y.
DEPENDS on #5939
- How I did it
Modify DHCP relay docker makefile and dockerfile. Make changes to sonic_debian_extension.j2 to install sonic packages.
I moved DHCP related CLI tests from sonic-utilities to DHCP relay docker.
This PR introduces a way to write a plugin as part of docker image and run the tests from cli-plugin-tests directory under docker directory.
The test result is available in target/docker-dhcp-relay.gz.log:
[ REASON ] : target/docker-dhcp-relay.gz does not exist NON-EXISTENT PREREQUISITES: docker-start target/docker-config-engine-buster.gz-load target/python-wheels/sonic_utilities-1.2-py3-none-any.whl-in
stall target/debs/buster/python3-swsscommon_1.0.0_amd64.deb-install
[ FLAGS FILE ] : []
[ FLAGS DEPENDS ] : []
[ FLAGS DIFF ] : []
============================= test session starts ==============================
platform linux -- Python 3.7.3, pytest-3.10.1, py-1.7.0, pluggy-0.8.0 -- /usr/bin/python3
cachedir: .pytest_cache
rootdir: /sonic/dockers/docker-dhcp-relay/cli-plugin-tests, inifile:
plugins: cov-2.6.0
collecting ... collected 10 items
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_plugin_registration PASSED [ 10%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_nonexist_vlanid PASSED [ 20%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_invalid_vlanid PASSED [ 30%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_invalid_ip PASSED [ 40%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_exist_ip PASSED [ 50%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_del_dhcp_relay_dest PASSED [ 60%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_remove_nonexist_dhcp_relay_dest PASSED [ 70%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_remove_dhcp_relay_dest_with_nonexist_vlanid PASSED [ 80%]
test_show_dhcp_relay.py::TestVlanDhcpRelay::test_plugin_registration PASSED [ 90%]
test_show_dhcp_relay.py::TestVlanDhcpRelay::test_dhcp_relay_column_output PASSED [100%]
=============================== warnings summary ===============================
/usr/local/lib/python3.7/dist-packages/tabulate.py:7
/usr/local/lib/python3.7/dist-packages/tabulate.py:7: DeprecationWarning: Using or importing the ABCs from 'collections' instead of from 'collections.abc' is deprecated, and in 3.8 it will stop working
from collections import namedtuple, Iterable
-- Docs: https://docs.pytest.org/en/latest/warnings.html
==================== 10 passed, 1 warnings in 0.35 seconds =====================
NOTE: This is cherry-pick from 1911/2012 to master.
- Why I did it
To fix LAG IP configuration race
- How I did it
Extended timeout for teammgrd
- How to verify it
Add >80 router LAGs. Do config reload
Signed-off-by: Nazarii Hnydyn <nazariig@nvidia.com>
#### Why I did it
The process of config generation (sonic-cfggen) fails, but the services continue to run with invalid config
#### How I did it
* add exit with error on errors in start.sh script (because supervisord relies on start.sh return code).
* fix jinja template. Jinja use common python expressions under the hood and `has_key` method was removed from dict in py3, so use check by `in` operator as it is supported by both py2 and py3.
#### How to verify it
* compile sonic with enabled iccp.
* add mclag config to CONFIG_DB.
```
'MC_LAG|1' => {
"local_ip": "10.0.0.2",
"peer_ip": "10.0.0.3",
"peer_link": "Ethernet8",
"mclag_interface": "Ethernet12"
}
* unmaks, enable and start swss and iccpd services in sonic.
* log in into the iccpd container and check the config file `/etc/iccpd/iccpd.conf`
* expected config:
```
mclag_id:1
local_ip:10.0.0.2
peer_ip:10.0.0.3
peer_link:Ethernet8
mclag_interface:Ethernet12
system_mac:YOUR_SYSTEM_MAC
#### Description for the changelog
Fixed initial iccpd startup configuration.
#### Why I did it
ethtool can be used to query and change settings such as speed, auto- negotiation and checksum offload on many network devices, especially Ethernet devices.
#### How I did it
add package extension to docker-platform-monitor/Dockerfile.j2
#### Why I did it
The libpci library provides portable access to configuration registers of devices connected to the PCI bus.
#### How I did it
update dockers/docker-platform-monitor/Dockerfile.j2
A recent version of contextlib2 (https://pypi.org/project/contextlib2/21.6.0/#history) has broken Python2 compatibility, so the version picked up by netaddr when using Python2 must be specified, or else builds fail
Co-authored-by: Tom Zhu <tom.zhu@metaswitch.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
In the multi asic platforms all the ASIC are advertising the same IPv6 /64 network from Loopback4096.
Therefore, the IPv6 loopback address of backend asic is not learnt on the frontend asic.
Change the bgpd.conf.main.conf.j2 template file to advertise the Loopback4096 ipv6 address as /128
Why I did it
Quagga is no longer being used. Remove quagga-related code (e.g., docker-fpm-quagga, sonic-quagga, etc.).
How I did it
Remove quagga-related code.
Why I did it
Quagga is no longer being used. Remove quagga-related code (e.g., docker-fpm-quagga, sonic-quagga, etc.).
How I did it
Remove quagga-related code.
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
Currently we leveraged the Supervisor to monitor the running status of critical processes in each container and it is more reliable and flexible than doing the monitoring by Monit. So we removed the functionality of monitoring the critical processes by Monit.
How I did it
I removed the script process_checker and corresponding Monit configuration entries of critical processes.
How to verify it
I verified this on the device str-7260cx3-acs-1.
- Why I did it
migrate to python3 support
add dependent packages for Klish
allow login as non-root user
- How I did it
update sonic-cli script to start Klish with user name, system name and timeout
update the Dockerfile.j2 to resolve dependent packages
add python3-dev for Klish use
- How to verify it
Incremental buster build with Azure/sonic-mgmt-framework#76 and verify the sonic-cli
- Description for the changelog
Migrate to python3.7 support, update sonic-cli script and resolve package dependencies
#### Why I did it
To avoid the following error
```
Traceback (most recent call last):
File "/usr/local/bin/flush_unused_database", line 10, in <module>
if 'PONG' in output:
TypeError: a bytes-like object is required, not 'str'
```
`communicate` method returns the strings if streams were opened in text mode; otherwise, bytes.
In our case text arg in Popen is not true and that means that `communicate` return the bytes
#### How I did it
Set `text=True` to get strings instead of bytes
#### How to verify it
run `/usr/local/bin/flush_unused_database` inside database container
I added `chassis_db_init` to the startup tasks for the `docker-platform-monitor` docker so that the script is run on startup of the switch and the chassis info is correctly provisioned to STATE_DB.
Depends on https://github.com/Azure/sonic-platform-daemons/pull/183
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
This PR aims to monitor the memory usage of streaming telemetry container and restart streaming telemetry container if memory usage is larger than the pre-defined threshold.
How I did it
I borrowed the system tool Monit to run a script memory_checker which will periodically check the memory usage of streaming telemetry container. If the memory usage of telemetry container is larger than the pre-defined threshold for 10 times during 20 cycles, then an alerting message will be written into syslog and at the same time Monit will run the script restart_service to restart the streaming telemetry container.
How to verify it
I verified this implementation on device str-7260cx3-acs-1.
- Why I did it
To give SONiC Application Extension developers an environment to run and develop their apps.
- How I did it
Created sonic-sdk and sonic-sdk-buildenv dockers and their dbg versions.
- How to verify it
Build:
$ make -f slave target/sonic-sdk.gz target/sonic-sdk-buildenv.gz
#### Why I did it
To avoid the following logs
```
Mar 15 15:52:04.599302 igk-dut-04 INFO database#/supervisord: flushdb /bin/bash: /usr/local/bin/flush_unused_database: /usr/bin/python: bad interpreter: No such file or directory
Mar 15 15:52:04.599947 igk-dut-04 INFO database#supervisord 2021-03-15 15:52:04,599 INFO exited: flushdb (exit status 126; not expected)
```
#### How I did it
Fix shebang
#### How to verify it
Check the logs
fuser support is required since new cisco hardware watchdog plugin uses them to check anyone else use's /dev/watchdogX resource. The actual validation happens in the platform code, but the package is required for pmon container. Currently the /dev/watchdogX is being used by cisco platform-monitor service. Cisco chassis level watchdog plugin uses "fuser" to claim the watchdog release from platform-monitor service.
#### Why I did it
MSN4700 A1/A0 used different sensor chip but keep the existing platform name *x86_64-mlnx_msn4700-r0*, this is a workaround to replace the sensor conf on MSN4700 A1/A0
#### How I did it
Use a shell script to get the sensor conf path and copy that files to /etc/sensors.d/sensors.conf
Why I did it
ndppd by default reads /proc/net/ipv6_route ever 30 seconds. Since T1s advertise so many routes to ToRs, this file is extremely large, and reading it causes ndppd's CPU usage to spike every 30 seconds
How I did it
Increase the delay for reading this file to the maximum possible value (max integer value), which will result in CPU spikes every ~24 days instead of every 30 seconds
How to verify it
Start ndppd with the new config file, confirm that no CPU spikes are seen except at startup
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
The aiohttp package is required by azure.kusto.data which is used by sonic-mgmt/test_reporting.
This change is to ensure that the dependent package is installed in the sonic-mgmt docker.
Signed-off-by: Xin Wang <xiwang5@microsoft.com>
Why I did it
Support readonly version of the command vtysh
How I did it
Check if the command starting with "show", and verify only contains single command in script.
* Why I did it
Upgrade to the latest ixnetwork-restpy and ixnetwork-open-traffic-generator pypi packages
* How I did it
Updated the pip install entries for the packages in the Dockerfile.j2
* How to verify it
pip show ixnetwork-restpy
pip show ixnetwork-open-traffic-generator
Co-authored-by: Neetha John <nejo@microsoft.com>
For the split mode, the config files, like bgpd.conf, zebra.conf and so on, were provided by outside. But the docker_init.sh will overwrite the outside config files if restart bgp service.
How I did it
Add a split mode checking in docker_init.sh, if docker_routing_config_mode is split, don't overwrite the existing routing config files.
How to verify it
Set split mode in config db
{
"DEVICE_METADATA": {
"localhost": {
"hwsku": "Force10-S6000",
"platform": "x86_64-kvm_x86_64-r0",
"docker_routing_config_mode": "split"
...
}
}
}
Replace your bgpd.conf to /etc/sonic/frr/bgpd.conf
Restart bgp service by sudo service bgp restart
The /etc/sonic/frr/bgpd.conf your provided shouldn't be overwritten
Signed-off-by: Ze Gan <ganze718@gmail.com>
- Support compile sonic arm image on arm server. If arm image compiling is executed on arm server instead of using qemu mode on x86 server, compile time can be saved significantly.
- Add kernel argument systemd.unified_cgroup_hierarchy=0 for upgrade systemd to version 247, according to #7228
- rename multiarch docker to sonic-slave-${distro}-march-${arch}
Co-authored-by: Xianghong Gu <xgu@centecnetworks.com>
Co-authored-by: Shi Lei <shil@centecnetworks.com>
This commit has following changes:
* Add templates and code to support VoQ chassis iBGP peers
* Add support to convert a new VoQChassisInternal element in the
BGPSession element of the minigraph to a new BGP_VOQ_CHASSIS_NEIGHBOR
table in CONFIG_DB.
* Add a new set of "voq_chassis" templates to docker-fpm-frr
* Add a new BGP peer manager to bgpcfgd to add neighbors from the
BGP_VOQ_CHASSIS_NEIGHBOR table using the voq_chassis templates.
* Add a test case for minigraph.py, making sure the VoQChassisInternal
element creates a BGP_VOQ_CHASSIS_NEIGHBOR entry, but not if its
value is "false".
* Add a set of test cases for the new voq_chassis templates in
sonic-bgpcfgd tests.
Note that the templates expect the new
"bgp bestpath peer-type multipath-relax" bgpd configuration to be
available.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
With the latest 201911 image, the following error was seen on staging devices with TSB command ( for both single asic, multi asic ). Though this err message doesn't affect the TSB functionality, it is good to fix.
admin@STG01-0101-0102-01T1:~$ TSB
BGP0 : % Could not find route-map entry TO_TIER0_V4 20
line 1: Failure to communicate[13] to zebra, line: no route-map TO_TIER0_V4 permit 20
% Could not find route-map entry TO_TIER0_V4 30
line 2: Failure to communicate[13] to zebra, line: no route-map TO_TIER0_V4 deny 30
In addition, in this PR I am fixing the message displayed to user when there are no BGP neighbors configured on that BGP instance. In multi-asic device there could be case where there are no BGP neighbors configured on a particular ASIC.
Avoid the following error messages while dynamic buffer calculation is enabled
```
ERR monit[491]: 'swss|buffermgrd' status failed (1) -- '/usr/bin/buffermgrd -l' is not running in host
```
Change /usr/bin/buffermgrd -l to /usr/bin/buffermgrd. The buffermgrd is started by -l for traditional model or -a for dynamic model. So we need to use the common section of both.
Signed-off-by: Stephen Sun <stephens@nvidia.com>
The default bgp connect retry timer is 120 seconds. A reconnection will happen 120 seconds if the initial connection fails. This PR aims to allow a more frequent retry.
Why I did it
It was observed that on a multi-asic DUT bootup, the BGP internal sessions between ASIC's was taking more time to get ESTABLISHED than external BGP sessions. The internal sessions was coming up almost exactly 120 secs later.
In multi-asic platform the bgp dockers ( which is per ASIC ) on switch start are bring brought up around the same time and they try to make the bgp sessions with neighbors (in peer ASIC's) which may be not be completely up. This results in BGP connect fail and the retry happens after 120sec which is the default Connect Retry Timer
How I did it
Add the command to set the bgp neighboring session retry timer to 10sec for internal bgp neighbors.
#### Why I did it
It is possible to have DHCP relay configuration with no servers/
helpers which result in DHCP container to crash. This PR fixes this
issue by not starting DHCP relay for vlans with no DHCP helpers.
resolves: #6931closes: #6931
#### How I did it
Do not add program group for dhcp relay with not dhcp helpers
#### How to verify it
Unit test
1. Made the command next-hop-self force only applicable on back-end asic bgp. This is done so that BGPL iBGP session running on backend can send e-BGP learn nexthop. Back end asic FRR is able to recursively resolve the eBGP nexthop in its routing table since it knows about all the connected routes advertise from front end asic.
2. Made all front-end asic bgp use global loopback ip (Loopback0) as router id and back end asic bgp use Loopbacl4096 as ruter-id and originator id for Route-Reflector. This is done so that routes learnt by external peer do not see Loopback4096 as router id in show ip bgp <route-prerfix> output.
3. To handle above change need to pass Loopback4096 from BGP manager for jinja2 template generation. This was missing and this change/fix is needed for this also https://github.com/Azure/sonic-buildimage/blob/master/dockers/docker-fpm-frr/frr/bgpd/templates/dynamic/instance.conf.j2#L27
4. Enhancement to add mult_asic specific bgpd template generation unit test cases.
Enable BBR config allowas-in 1 for internal peers
Why I did:
To advertise BBR routes learnt via e-BGP peer in one asic/namespace to another iBGP asic/namespace via Route Reflector.
adding noTLS mode for debugging purpose
Removing config-set for port 8080. It fails to start telemetry if docker restarts in case on noTLS mode because it expects log_level config to be present as well.
- Introduced TS common file in docker as well and moved common functions.
- TSA/B/C scripts run only in BGP instances for front end ASICs.
In addition skip enforcing it on route maps used between internal BGP sessions.
admin@str--acs-1:~$ sudo /usr/bin/TSA
System Mode: Normal -> Maintenance
and in case of Multi-ASIC
admin@str--acs-1:~$ sudo /usr/bin/TSA
BGP0 : System Mode: Normal -> Maintenance
BGP1 : System Mode: Normal -> Maintenance
BGP2 : System Mode: Normal -> Maintenance
The requirement for zebra to be ready to accept connections is a generic problem that is not
specific to bgpd. Making the script to wait for zebra socket a separate script and let bgpd and
staticd to wait for zebra socket.
- combine docker-ptf-saithrift into docker-ptf docker
- build docker-ptf under platform vs
- remove docker-ptf for other platforms
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Recent changes brought l2 vlan concept which do not have DHCP
clients behind them and so DHCP relay is not required. Also,
dhcpmon fails to launch on those vlans as their interfaces
lack IP addresses. This PR limit launch of both DHCP relay
and dhcpmon to L3 vlans only.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
- Support for non-template based FRR configurations (BGP, route-map, OSPF, static route..etc) using config DB schema.
- Support for save & restore - Jinja template based config-DB data read and apply to FRR during startup
**- How I did it**
- add frrcfgd service
- when frr_mgmg_framework_config is set, frrcfgd starts in bgp container
- when user changed the BGP or other related table entries in config DB, frrcfgd will run corresponding VTYSH commands to program on FRR.
- add jinja template to generate FRR config file to be used by FRR daemons while bgp container restarted
**- How to verify it**
1. Add/delete data on config DB and then run VTYSH "show running-config" command to check if FRR configuration changed.
1. Restart bgp container and check if generated FRR config file is correct and run VTYSH "show running-config" command to check if FRR configuration is consistent with attributes in config DB
Co-authored-by: Zhenhong Zhao <zhenhong.zhao@dell.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan arlakshm@microsoft.com
- Why I did it
This PR has the changes to support having different swss.rec and sairedis.rec for each asic.
The logrotate script is updated as well
- How I did it
Update the orchagent.sh script to use the logfile name options in these PRs(Azure/sonic-swss#1546 and Azure/sonic-sairedis#747)
In multi asic platforms the record files will be different for each asic, with the format swss.asic{x}.rec and sairedis.asic{x}.rec
Update the logrotate script for multiasic platform .
**- Why I did it**
Ledd is the last daemon that is not enabled to run in python3.
Even though there is a plan to deprecate this daemon and to replace it by something else it's one simple step toward python2 deprecation.
**- How I did it**
Changed the `command=` line for `ledd` in the `supervisord` configuration of `pmon`.
Copied what was done for other daemons.
**- How to verify it**
Booting a product that has a `led_control.py` should now show the ledd running in python3.
I ran `python3 -m pylint` on all `led_control.py` plugin which means that most of them should be python3 compliant.
There is however still a risk that some might not work.
- Why I did it
Initially, we used Monit to monitor critical processes in each container. If one of critical processes was not running
or crashed due to some reasons, then Monit will write an alerting message into syslog periodically. If we add a new process
in a container, the corresponding Monti configuration file will also need to update. It is a little hard for maintenance.
Currently we employed event listener of Supervisod to do this monitoring. Since processes in each container are managed by
Supervisord, we can only focus on the logic of monitoring.
- How I did it
We borrowed the event listener of Supervisord to monitor critical processes in containers. The event listener will take
following steps if it was notified one of critical processes exited unexpectedly:
The event listener will first check whether the auto-restart mechanism was enabled for this container or not. If auto-restart mechanism was enabled, event listener will kill the Supervisord process, which should cause the container to exit and subsequently get restarted.
If auto-restart mechanism was not enabled for this contianer, the event listener will enter a loop which will first sleep 1 minute and then check whether the process is running. If yes, the event listener exits. If no, an alerting message will be written into syslog.
- How to verify it
First, we need checked whether the auto-restart mechanism of a container was enabled or not by running the command show feature status. If enabled, one critical process should be selected and killed manually, then we need check whether the container will be restarted or not.
Second, we can disable the auto-restart mechanism if it was enabled at step 1 by running the commnad sudo config feature autorestart <container_name> disabled. Then one critical process should be selected and killed. After that, we will see the alerting message which will appear in the syslog every 1 minute.
- Which release branch to backport (provide reason below if selected)
201811
201911
[x ] 202006
Fix#5026
There is a race condition between zebra server accepts connections and bgpd tries to connect. Bgpd has a chance to try to connect before zebra is ready. In this scenario, bgpd will try again after 10 seconds and operate as normal within these 10 seconds. As a consequence, whatever bgpd tries to sent to zebra will be missing in the 10 seconds. To avoid such a scenario, bgpd should start after zebra is ready to accept connections.
**- Why I did it**
Earlier today we found a bug in the SONiC TSA implementation.
TSC shows incorrect output (see below) in case we have a route-map which contains TSA route-map as a prefix.
```
admin@str-s6100-acs-1:~$ TSC
Traffic Shift Check:
System Mode: Not consistent
```
The reason is that TSC implementation has too loose regexps in TSA utilities, which match wrong route-map entries:
For example, current TSC matches following
```
route-map TO_BGP_PEER_V4 permit 200
route-map TO_BGP_PEER_V6 permit 200
```
But it should match only
```
route-map TO_BGP_PEER_V4 permit 20
route-map TO_BGP_PEER_V4 deny 30
route-map TO_BGP_PEER_V6 permit 20
route-map TO_BGP_PEER_V6 deny 30
```
**- How I did it**
I fixed it by using egrep with `^` and `$` regexp markers which match begin and end of the line.
**- How to verify it**
1. Add follwing entry to FRR config:
```
str-s6100-acs-1#
str-s6100-acs-1# conf t
str-s6100-acs-1(config)# route-map TO_BGP_PEER_V4 permit 200
str-s6100-acs-1(config-route-map)# end
```
2. Use the TSC command and check output. It should show normal.
```
admin@str-s6100-acs-1:~$ TSC
Traffic Shift Check:
System Mode: Normal```
fix platform driver breakage due to python3 upgrade and fix load minigraph errors with config load_minigraph -y
**- How I did it**
added python3-smbus to the pmon docker template since the previous was python2 specific
fixed additional "ord" python2 specific code
fixed the jinja templates used by qos reload - the template logic required data to be parsed
**- How to verify it**
run "show platform XXX" commands and verify output
run "sudo config load_minigraph -y" and verify configuration
run "show interfaces XXX" and verify output
Co-authored-by: Carl Keene <keene@nokia.com>
The HLD about MACsec feature is at :
https://github.com/Azure/SONiC/blob/master/doc/macsec/MACsec_hld.md
- How to verify it
This PR doesn't set MACsec container automatically start, You should manually start the container by docker run docker-macsec
wpa_supplicant binary can be found at MACsec container.
This PR depends on the PR, WPA_SUPPLICANT, and The MACsec container will be set as automatically start by later PR.
Signed-off-by: zegan <zegan@microsoft.com>
* Use 20 and 30 route-map entries instead of 2 and 3 for TSA
* Added support for dynamic "Allow list" default action.
Co-authored-by: Pavel Shirshov <pavel.contrib@gmail.com>
- Make PDDF code compliant with both Python 2 and Python 3
- Align code with PEP8 standards using autopep8
- Build and install both Python 2 and Python 3 PDDF packages
Enable the notify mode of rsyslogd imfile module used for supervisord
logs in docker container.
Setup the mode="inotify" when loading imfile, made sure we are are getting
supervisord logs in host immediately.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
**- Why I did it**
I'm updating the jinja2 template to support getting SNMP information from the redis configdb.
I'm using the format approved here:
https://github.com/Azure/SONiC/pull/718
This will pave the way for us to decrement using the snmp.yml in the future.
Right now we will still be using both the snmp.yml and configdb to get variable information in order to create the snmpd.conf via the sonic-cfggen tool.
**- How I did it**
I first updated the SNMP Schema in PR #718 to get that approved as a standardized format.
Then I verified I could add snmp configs to the configdb using this standard schema. Once the configs were added to the configdb then I updated the snmpd.conf.j2 file to support the updates via the configdb while still using the variables in the snmp.yml file in parallel. This way we will have backward compatibility until we can fully migrate to the configdb only.
By updating the snmpd.conf.j2 template and running the sonic-cfggen tool the snmpd.conf gets generated with using the values in both the configdb and snmp.yml file.
Co-authored-by: trvanduy <trvanduy@microsoft.com>
Mellanox already supports multiple destination IPs in IPinIP tunnel configuration, thus removing mellanox
exception for IPinIP configuration.
- How I did it
Removed "dst_ip" field generation in mellanox platform condition.
Sorted the "dst_ip" list, so that it is easier to test against sample configuration in unit tests.
Aligned unit test sample.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
This PR is in preparation to move from snmp.yml to configdb. This will more closely align with other commands in sonic and use configdb as the source of truth for snmp configuration.
Note: This is the first of 2 PR's to enable this. This PR will not change any functionality but will allow the snmp.yml file info to be put into the configdb.
Created a script that takes the snmp.yml variables and converts them to the configdb format.
Added file to dockerfile.j2 so that file is copied in the container.
Updated start.sh file to automatically run the python conversion script each time the docker container is restarted.
frr does not advertise route if local route is not reachable, as a result
loopback route /64 is not advertised to the neighbors. Add static route
allows frr to advertise the route to its peers
Signed-off-by: Guohan Lu <lguohan@gmail.com>
**- Why I did it**
python2 is end of life and SONiC is going to support python3. This PR is going to support:
1. Build pmon daemons with python3
2. Install and run python3 version pmon daemons
**- How I did it**
1. Change pmon daemons make files to build bothe python2 and python3 whl
2. Change docker-platform-monitor make files to install both python2 and python3 whl
3. Change pmon docker startup files to start pmon daemons according to the supported platform API version
Introduce tunnel manager daemon. Start the process as part of swss container
Submodule update for swss:
9ed3026 - 2020-12-24 : [NAT] ACL Rule with DO_NOT_NAT action is getting failed. (#1502) [Akhilesh Samineni]
c39a4b1 - 2020-12-23 : Mux/IPTunnel orchagent changes (#1497) [Prince Sunny]
bc8df0e - 2020-12-23 : Add support for headroom pool watermark (#1567) [Neetha John]
**- Why I did it**
As part of migrating SONiC codebase from Python 2 to Python 3
**- How I did it**
- No longer install Python 2 in docker-base-buster or docker-config-engine-buster.
- Install Python 2 and pip2 in the following containers until we can completely eliminate it there:
- docker-platform-monitor
- docker-sonic-mgmt-framework
- docker-sonic-vs
- Pin pip2 version <21 where it is still temporarily needed, as pip version 21 will drop support for Python 2
- Also preform some other cleanup, ensuring that pip3, setuptools and wheel packages are installed in docker-base-buster, and then removing any attempts to re-install them in derived containers
