Why I did it
Fix some unreliability seen on emmc device with some AMD CPUs
How I did it
Added a kernel parameter to add quirks to
It depends on a sonic-linux-kernel change to work properly but will be a no-op without it.
The quirk added is SDHCI_QUIRK2_BROKEN_HS200 used to downgrade the link speed for the eMMC.
Why I did it
On a supervisor card in a chassis, syncd/teamd/swss/lldp etc dockers are created for each Switch Fabric card. However, not all chassis would have all the switch fabric cards present. In this case, only dockers for Switch Fabrics present would be created.
system-health indicates errors in this scenario as it is expecting dockers for all Switch Fabrics (based on NUM_ASIC defined in asic.conf file).
system-health process error messages were also altered to indicate which container had the issue; multiple containers may run processes with the same name, which can result in identical system-health error messages, causing ambiguity.
How I did it
Port container_checker logic from #11442 into service_checker for system-health.
How to verify it
Bringup Supervisor card with one or more missing fabric cards. Execute 'show system-health summary'. The command should not report failure due to missing dockers for the asics on the fabric cards which are not present.
Why I did it
To address error sometimes seen when running sonic-mgmt test_stress_routes.py::test_announce_withdraw_route on 720DT-48S
How I did it
Update boot0 logic to set platform specific varlog size for 720DT-48S
How to verify it
Verified that /var/log size increased and error is no longer observed when running test
Why I did it
1. fix chassis test_set_fans_led case
2. fix chassis get_name case mismatch issue
3. fix fan_drawer test_set_fans_speed
4. fix component test_components test case
How I did it
Add corresponding configuration into chassis json file
How to verify it
Run platform tests cases to verify these failure cases
- Why I did it
In to-sonic and multi-asic KVM-test, pretest sometimes failed. Reason is rsyslogd process can not start in teamd container. Because rsyslog.conf is empty caused by sonic-cfggen execute failed
- How I did it
If sonic-cfggen -d execute failed, execute without -d because the template file has the default value.
- How to verify it
Build image and test it over 40 times, all passed pretest.
Signed-off-by: Chun'ang Li <chunangli@microsoft.com>
add SEU reporting on chassis
fix fallback logic for Clearlake eeprom identification
fix fan speed reporting for a specific model
move pcie timeout configuration for Upperlake in platform code (deprecates hwsku-init)
Why I did it
High CPU utilization by entropy.py
How I did it
Remove entropy script as it does not work anymore and is no longer needed for bullseye(202205).
In Buster(202012) the max available poolsize (entropy_avail) for entropy is 4096 and our entropy.py script was based on this value. With the change in kernel to bullseye on 202205 this entropy poolsize was changed to 256 which also causes our script to fail.
This script was initially added to provide SW assistance to improve the system entropy value available early on in the Sonic boot sequence on buster.
On bullseye (Linux kernel 5.10) this is no longer needed as this feature has been improved.
How to verify it
run "top" command to check CPU usage.
Why I did it
Submodule advances:
sonic-utilities
8e8e6088 - [202211][dhcp_relay] Remove add field of vlanid to DHCP_RELAY table while adding vlan ([201811 sub-module] advance sub-modules: utilities, swss, swss-common #2679) (16 hours ago) [Yaqiang Zhu]
1400fb94 - [GCU] Ignore bgpraw in GCU applier (Fix sfputil indexing for 7170-Q59S20 #2623) (15 hours ago) [jingwenxie]
f76a6364 - [vlan] Refresh dhcpv6_relay config while adding/deleting a vlan ([sonic-py-swsssdk] Update submodule #2660) (15 hours ago) [Yaqiang Zhu]
7849e18d - [db_migrator] make LOG_LEVEL_DB migration more robust (Mellanox platform: attach queues 2 and 6 to lossy profile using generic buffer template #2651) (16 hours ago) [Stepan Blyshchak]
c7df6dfa - Fixed a bug in "show vnet routes all" causing screen overrun. (Add hook to allow customizing link cable lengths #2644) (16 hours ago) [siqbal1986]
a5505f02 - show logging CLI support for logs stored in tmpfs (Traceback error seen while issuing show interface commands with if_names #2641) (16 hours ago) [mihirpat1]
bbacb91a - [system-health] Fix issue: show system-health CLI crashes (Updating deb package for platform and sai #2635) (16 hours ago) [Junchao-Mellanox]
8d724024 - [sai_failure_dump]Invoking dump during SAI failure ([dockers]: Upgrade LLDP docker to stretch build #2633) (16 hours ago) [Sudharsan Dhamal Gopalarathnam]
3c3be526 - Add transceiver info CLI support to show output from TRANSCEIVER_INFO for ZR ([submodule]: Update sonic-sairedis pointer #2630) (16 hours ago) [mihirpat1]
37f41666 - [show] add support for gRPC show commands for active-active ([bitmap-vnet]: Bitmap vnet test image [DO NOT MERGE] #2629) (16 hours ago) [vdahiya12]
b06d7fe4 - [show_bfd] add local discriminator in show bfd command ([Pmon] Selectively load pmon container daemons #2625) (16 hours ago) [Baorong Liu]
6adcd3e8 - [GCU] Ignore bgpraw table in GCU operation ([Mellanox] Fix SAI version #2628) (16 hours ago) [jingwenxie]
c65bdc35 - [muxcable][config] Add support to enable/disable ceasing to be an advertisement interface when radv service is stopped (Add knob in ConfigDB to enable/disable telemetry container #2622) (16 hours ago) [Jing Zhang]
91e9457f - Add Transceiver PM basic CLI support to show output from TRANSCEIVER_PM table for ZR ([201803] Restart SwSS, syncd and dependent services if a critical process in syncd container exits #2615) (16 hours ago) [longhuan-cisco]
54cc8c5a - Remove TODO comment which is no longer relevant (Warm-reboot: teamd warm restart caused neighbor deleted and learned again. #2600) (16 hours ago) [Lior Avramov]
6891b4fb - Making 'show feature autorestart' more resilient to missing auto_restart config in CONFIG_DB ([submodule] update mellanox hw-mgmgt pointer (V.2.0.0061) #2592) (16 hours ago) [kartik-arista]
1e8bea37 - [storyteller] add link prober state change to story teller ([sonic-buildimage] New feature managementVRF(L3mdev) #2585) (16 hours ago) [Jing Zhang]
7481a20f - Extend fast-reboot STATE_DB entry timer ([submodule]: update sonic-swss-common, sonic-py-swsssdk, sonic-snmpagent #2577) (16 hours ago) [Aryeh Feigin]
0e08701c - [sonic_installer] use /etc/resolv.conf from the host when migrating packages (Set a rate limit on syslog messages from all Docker containers #2573) (16 hours ago) [Stepan Blyshchak]
06096780 - Fixed admin state config CLI for Backport interfaces (Prior to install a new ONIE SONiC image, delete all partitions except EFI/ONIE #2557) (16 hours ago) [anamehra]
9f1f13e4 - [show] Add bgpraw to show run all (Fixed typo on paragraph #40#2537) (16 hours ago) [jingwenxie]
98bc8bd2 - [chassis][voq] Add "show fabric reachability" command. ([ntp]: Build 4.2.6 locally. #2528) (16 hours ago) [jfeng-arista]
3a50b63f - Preserve copp tables through DB migration ([docker-radvd]: upgrade docker radvd to stretch based #2524) (16 hours ago) [Aryeh Feigin]
28f6b127 - [masic] 'show interfaces counters' reminds to use '-d all' option to check for internal links (solve dependency issue #2466) (16 hours ago) [wenyiz2021]
15026e14 - suppport multi asic for show queue counter ([dockers] Prevent old supervisord messages from gettting re-logged to syslog #2439) (16 hours ago) [zhixzhu]
2d773e17 - [masic support] 'show run bgp' support for multi-asic (lo address not synced to the asic #2427) (16 hours ago) [wenyiz2021]
sonic-swss
4f304bc - [EVPN]Handling race condition when remote VNI arrives before tunnel map entry ([sonic-quagga] Function defect, do NOT cancel route while connect IP down #2642) (15 hours ago) [Sudharsan Dhamal Gopalarathnam]
34fc615 - [sai_failure_dump]Invoking dump during SAI failure (Add hook to allow customizing link cable lengths #2644) (15 hours ago) [Sudharsan Dhamal Gopalarathnam]
b817695 - [autoneg]Fixing adv interface types to be set when AN is disabled (Fix issue with platform file path name #2638) (15 hours ago) [Sudharsan Dhamal Gopalarathnam]
ab36bd4 - [bfdorch] add local discriminator to state DB ([bitmap-vnet]: Bitmap vnet test image [DO NOT MERGE] #2629) (15 hours ago) [Baorong Liu]
6343471 - Remove TODO comments that are no longer relevant (Add knob in ConfigDB to enable/disable telemetry container #2622) (15 hours ago) [Lior Avramov]
2b1869c - [refactor]Refactoring sai handle status (Rollback kernel submodule update. #2621) (15 hours ago) [Sudharsan Dhamal Gopalarathnam]
c41a1b7 - Fix issue ARP entry is out of sync between kernel and APPL_DB after warm reboot if the ARP entry is updated more than once during warm reboot in PFC watchdog warm reboot test #13341 ARP entry can be out of sync between kernel and APPL_DB if multiple updates are received from RTNL ([sub module] advance sonic-utilities sub module for 201811 branch #2619) (15 hours ago) [Stephen Sun]
da0cf7a - Changed the BFD default detect multiplier to 10x ("failed to load plugin io.containerd.snapshotter..." seen during linux boot up #2614) (15 hours ago) [siqbal1986]
13b5adf - [vstest] Only collect stdout of orchagent_restart_check in vstest ([submodules] update swss and utilities pointers #2597) (15 hours ago) [bingwang-ms]
2b9d94d - Avoid aborting orchagent when setting TUNNEL attributes (build failing for PLATFORM=p4 #2591) (15 hours ago) [Stephen Sun]
99b7d3b - Only collect stdout of orchagent_restart_check in vstest ( [saibcm-modules]: import new bcm modules #2578) (15 hours ago) [bingwang-ms]
5209c42 - dereg acl-rule counters during acl-table del ([201803] Set a rate limit on syslog messages from all Docker containers #2574) (15 hours ago) [Vivek]
ae68054 - Fixed set mtu for deleted subintf due to late notification ([vs]: Add option to specify platform name for DVS orchagent #2571) (15 hours ago) [EdenGri]
ab13dfa - Remove TODO comments which are no longer needed (support set timezone in ConfigDB #2568) (15 hours ago) [Junchao-Mellanox]
a3545cf - Modify coppmgr mergeConfig to support preserving copp tables through reboot. (Added new SN3700/SN3700C Mellanox platforms #2548) (15 hours ago) [Aryeh Feigin]
be16e79 - Use github code scanning instead of LGTM ([201803] [services] Restart SwSS service upon unexpected critical process exit #2546) (15 hours ago) [Liu Shilong]
63c0234 - Updated handling of VRF_VNI mapping and VLAN_VNI mapping for same VNI ID (Move warm_restart enable/disable config to stateDB WARM_RESTART_ENABL… #2538) (15 hours ago) [Tapash Das]
4844111 - Fix potential risks ([mlnx] Fix sai xml path for boxer platform #2516) (15 hours ago) [Liran-Ar]
6420808 - [p4orch]: PINS Extension tables support ([build] When generating image version, handle case where current commit has no reachable tags #2506) (15 hours ago) [svshah-intel]
sonic-swss-common
1badd46 - Increase the netlink buffer size from 3MB to 16MB. (arp_update doesn't sleep 300 between each execution #739) (14 hours ago) [KISHORE KUNAL]
6555057 - Refactor eventpublisher deinit ([acl] Add default deny rule for l3 table #734) (14 hours ago) [Zain Budhwani]
f4d6de7 - Use github code scanning instead of LGTM ([sonic-quagga]:update submodule #718) (14 hours ago) [Liu Shilong]
sonic-linux-kernel
74f9a8f - Update linux kernel for hw-mgmt V.7.0020.4104 (Move template files to /usr/share/sonic/templates #305) (14 hours ago) [Stephen Sun]
6365701 - Fixes for emmc unreliability ([build_debian.sh]: Integrate system dump script #270) (14 hours ago) [Samuel Angebault]
How I did it
How to verify it
Avoid traceback on sonic-clear command
sonic-clear dhcp6relay_counters
Traceback (most recent call last):
File "/usr/local/bin/sonic-clear", line 8, in <module>
sys.exit(cli())
File "/usr/local/lib/python3.9/dist-packages/click/core.py", line 764, in __call__
return self.main(*args, **kwargs)
File "/usr/local/lib/python3.9/dist-packages/click/core.py", line 717, in main
rv = self.invoke(ctx)
File "/usr/local/lib/python3.9/dist-packages/click/core.py", line 1137, in invoke
return _process_result(sub_ctx.command.invoke(sub_ctx))
File "/usr/local/lib/python3.9/dist-packages/click/core.py", line 956, in invoke
return ctx.invoke(self.callback, **ctx.params)
File "/usr/local/lib/python3.9/dist-packages/click/core.py", line 555, in invoke
return callback(*args, **kwargs)
File "/usr/local/lib/python3.9/dist-packages/clear/plugins/dhcp-relay.py", line 19, in dhcp6relay_clear_counters
counter = DHCPv6_Counter()
NameError: name 'DHCPv6_Counter' is not defined
- How I did it
Corrected the way to import using importlib
- How to verify it
Tested the sonic-clear command and verified no traceback is seen
- Why I did it
To include latest fixes and new functionality
SDK/FW
1. Fixed bug in recovery mechanism in case of I2C error when trying to access the XSFP module.
2. On the NVIDIA Spectrum-2 switch, when receiving a packet with Symbol Errors on ports that are configured to cut-thought mode, a pipeline might get stuck.
3. On the Spectrum-2 and Spectrum-3 switch, if you enable ECN marking and the port is in split mode, traffic sent to the port under congestion (for example, when connecting two ports with a total speed of 50GbE to a single 25GbE port) is not marked.
4. Modifying existing entry/Adding new one when switch is at its maximum capacity (full by maximum allowed entries from any type such as routes, FDB, and so forth), will fail with an error.
5. When many ports are active (e.g., 70 ports up), and the configuration of shared buffer is applied on the fly, occasionally, the firmware might get stuck.
6. When a system has more than 256 ACL rules, on rare occasion, removing/adding rules may cause some ACL rules not to work.
7. On SN2201 system, on RJ45 port, the link might appear in 'down' state even if it operations properly.
8. Layer 4 port information is not initialized for BFD packet event. To address the issue, remote peer UDP port information was added in BFD packet event.
9. When setting LAG as a SPAN analyzer, the distributor mode of the LAG members was not taken into account. It may happen that the LAG member with distributor mode disabled will be set as a SPAN analyzer port.
- How I did it
Updated SDK/SAI submodule and relevant makefiles with the required versions.
- How to verify it
Build an image and run tests from "sonic-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
Add script usage and more information to script description being printed in help option.
- Why I did it
Missing information in script description in help option.
- How I did it
Expand script description and add script usage.
- How to verify it
Run the script with -h option.
- Why I did it
fixes#12907
When the management interface IP address configuration changes from dynamic to static the DNS configuration (retrieved from the DHCP server) in /etc/resolv.conf remains uncleared. This leads to a DNS configuration pointing to the wrong nameserver. To make the behavior clear DNS configuration received from DHCP should be cleared.
- How I did it
Use resolvconf package for managing DNS configuration. It is capable of tracking the source of DNS configuration and puts the configuration retrieved from the DHCP servers into a separate file. This allows the implementation of DNS configuration cleanup retrieved from DHCP during networking reconfiguration.
- How to verify it
Ensure that the management interface has no static configuration.
Check that /etc/resolv.conf has DNS configuration.
Configure a static IP address on the management interface.
Verify that /etc/resolv.conf has no DNS configuration.
Remove the static IP address from the management interface.
Verify that /etc/resolv.conf has DNS configuration retrieved form DHCP server.
After upgrade to brcmsai 8.1, the sdk running environment (container) recommended with mininum memory size as below
TH4/TD4(ltsw) uses 512MB
TH3 used 300MB
Helix4/TD2/TD3/TH/TH 256 MB
Base on this requirement, adjust the default syncd share memory size and set the memory size for special ACISs in platform_env.conf file for different types of Broadcom ASICs.
How I did it
Add the platform_env.conf file if none of it for broadcom platform (base on platform_asic file)
Add the 'SYNCD_SHM_SIZE' and set the value
for ltsw(TD4/TH4) devices set to 512M at least (update the platform_env.conf)
for Td2/TH2/TH devices set to 256M
for TH3 set to 300M
verify
How to verify it
verify the image with code fix
Check with UT
Check on lab devices
On a problematic device which cannot start successfully
Run with the command
$ cat /proc/linux-kernel-bde
Broadcom Device Enumerator (linux-kernel-bde)
Module parameters:
maxpayload=128
usemsi=0
dmasize=32M
himem=(null)
himemaddr=(null)
DMA Memory (kernel): 33554432 bytes, 0 used, 33554432 free, local mmap
No devices found
$ docker rm -f syncd
syncd
$ sudo /usr/bin/syncd.sh start
Cannot get Broadcom Chip Id. Skip set SYNCD_SHM_SIZE.
Creating new syncd container with HWSKU Force10-S6000
a4862129a7fea04f00ed71a88715eac65a41cdae51c3158f9cdd7de3ccc3dd31
$ docker inspect syncd | grep -i shm
"ShmSize": 67108864,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
On Normal device
$ docker inspect syncd | grep -i shm
"ShmSize": 268435456,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e"
change the config syncd_shm.ini to b85=128m
$ docker rm -f syncd
syncd
$ sudo /usr/bin/syncd.sh start
Creating new syncd container with HWSKU Force10-S6000
3209ffc1e5a7224b99640eb9a286c4c7aa66a2e6a322be32fb7fe2113bb9524c
$ docker inspect syncd | grep -i shm
"ShmSize": 134217728,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
change the config under
/usr/share/sonic/device/x86_64-dell_s6000_s1220-r0/Force10-S6000/platform_env.conf
and run command
$ cat /usr/share/sonic/device/x86_64-dell_s6000_s1220-r0/platform_env.conf
SYNCD_SHM_SIZE=300m
$ sudo /usr/bin/syncd.sh start
Creating new syncd container with HWSKU Force10-S6000
897f6fcde1f669ad2caab7da4326079abd7e811bf73f018c6dacc24cf24bfda5
$ docker inspect syncd | grep -i shm
"ShmSize": 314572800,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
Why I did it
sonic-sairedis
53488e9 - [sai_failure_dump]Invoking dump during SAI failure (Update Mellanox buffer profiles config #1198) (15 hours ago) [Sudharsan Dhamal Gopalarathnam]
85921af - [Mellanox] Enable DSCP remapping by using SAI attribute ([Nephos] Updating download link for SAI and SDK #1188) (15 hours ago) [Stephen Sun]
82f2cd7 - Switch to using stock gcovr 5.2 (Add service to config hostname based on configdb #1174) (15 hours ago) [Saikrishna Arcot]
3a6c60d - [ppi]: Enable bulk API. ([Aboot] Declare flash_size for all platform #1171) (15 hours ago) [Nazarii Hnydyn]
f1303cb - Use github code scanning instead of LGTM (#1160) (15 hours ago) [Liu Shilong]
b1972d9 - Fix for [EVPN] When MAC moves from remote end point to local, ASIC DB fields are not updated properly for the mac #11503Update NotificationProcessor.cpp ([libteam] Add fallback support for single-member-port LAG #1118) (15 hours ago) [anilkpan]
How I did it
How to verify it
Why I did it
Change the mirror config file
Use the files/build/versions/default/versions-mirror only when reproducible build enabled.
The config in files/build/versions is only for reproducible build, while snapshot mirror feature does not have the dependency on the reproducible build.
How I did it
Skip the mirror config in files/build/versions/default/versions-mirror if reproducible build not enabled.
How to verify it
Why I did it
advance sonic-platform-daemons
7219b56 - [Xcvrd]: Fix optics insertion/removal not detected (Add Ingrasys S9100 platform submodule #333) (3 days ago) [Prince George]
9b15ccf - add data for telemtery enhancement for 'active-active' cable type ([platform]: add support for Force10-Z9100 32x100G #332) (3 days ago) [vdahiya12]
1c7dba6 - Fix bug where transceiver info is missing after port breakout change ([teamd] Fix a bug in #305 that will break teamd #329) (3 days ago) [Tal Berlowitz]
07b8f3c - Xcvrd should restart if any child thread crashes (Update Mellanox SAI git reference #326) (3 days ago) [mihirpat1]
How I did it
How to verify it
Why I did it
advance sonic-platform-common
2dbc0ea - (HEAD, origin/202211) Change get_tx_bias return type to list ([platform]: add eeprom/sfputil support for z9100 #342) (2 days ago) [mihirpat1]
How I did it
How to verify it
Changing the default config knob value to be True for killing radv, due to the reasons below:
Killing RADV is to prevent sending the "cease to be advertising interface" protocol packet.
RFC 4861 says this ceasing packet as "should" instead of "must", considering that it's fatal to not do this.
In active-active scenario, host side might have difficulty distinguish if the "cease to be advertising interface" is for the last interface leaving.
6.2.5. Ceasing To Be an Advertising Interface
shutting down the system.
In such cases, the router SHOULD transmit one or more (but not more
than MAX_FINAL_RTR_ADVERTISEMENTS) final multicast Router
Advertisements on the interface with a Router Lifetime field of zero.
In the case of a router becoming a host, the system SHOULD also
depart from the all-routers IP multicast group on all interfaces on
which the router supports IP multicast (whether or not they had been
advertising interfaces). In addition, the host MUST ensure that
subsequent Neighbor Advertisement messages sent from the interface
have the Router flag set to zero.
sign-off: Jing Zhang zhangjing@microsoft.com
Why I did it
include changes from sairedis submodule
102d20b | [202211][submodule][SAI]Advance header include 0031470 | improve enum values integration check (#1727) (#1737)
04d3c41 | [Submodule][upgrade]Upgrade SAI submodule (#1204)
updates from SAI
7710e24 | [cherry-pick][202211]Enhance the check enum lock script (#1741) (#1742)
0031470 | improve enum values integration check (#1727) (#1737)
4f11c7e | Enable github code scanning to replace LGTM. (#1709)
How I did it
How to verify it
During docker build, host files can be passed to the docker build through
docker context files. But there is no straightforward way to transfer
the files from docker build to host.
This feature provides a tricky way to pass the cache contents from docker
build to host. It tar's the cached content and encodes them as base64 format
and passes it through a log file with a special tag as 'VCSTART and VCENT'.
Slave.mk in the host, it extracts the cache contents from the log and stores them
in the cache folder. Cache contents are encoded as base64 format for
easy passing.
<!--
Please make sure you've read and understood our contributing guidelines:
https://github.com/Azure/SONiC/blob/gh-pages/CONTRIBUTING.md
** Make sure all your commits include a signature generated with `git commit -s` **
If this is a bug fix, make sure your description includes "fixes #xxxx", or
"closes #xxxx" or "resolves #xxxx"
Please provide the following information:
-->
#### Why I did it
#### How I did it
#### How to verify it
Eariler the SDK stat polling was erroneously set to once every msec
which is far more frequent than required by SWSS. The new setting, which
is consistent with other vendor SKUs, is once a second. The net result
is reduced CPU MHz by syncd.
Why I did it
fix DX010 fan drawer and watchdog platform test case issues
How I did it
1. Add fan_drawer get_maximum_consumed_power support
2. Adjust maximum watchdog timeout value check
How to verify it
Run test_fan_drawer and test_watchdog test cases.
* [Security] Upgrade the openssl version to 1.1.1n-0+deb11u4+fips (#13737)
Why I did it
[Security] Upgrade the openssl version to 1.1.1n-0+deb11u4+fips
f6df7303d8 Update expired certs.
84540b59c1 CVE-2022-2068
f763d8a93e Prepare 1.1.1n-0+deb11u2
576562cebe CVE-2022-1292
How I did it
Upgrade the OpenSSL version
* [Security] Upgrade OpenSSL version for armhf
Adding /usr/local/bin/storyteller to READ_ONLY_CMDS. So no write access or prompt for password is needed to run storyteller.
Tested on 202205 clusters, user who didn't request write access was able to grep log using storyteller.
sign-off: Jing Zhang zhangjing@microsoft.com
Why I did it
This PR is an enhancement of PR #13105
Because the input string of AttachTo for ACL table can appear in both port name group and port alias group, I added a logic to determine whether the string should be port name or port alias
If all the input strings belong to port name group, then we treat all of them as port name
If all the input strings belong to port alias, then we treat all of them as port alias
If all the input string belongs to both port alias group and port name group, we prefer port alias. The behavior is as before.
How I did it
Walk through all port names/alias in the input to make a decision.
How to verify it
Verified by adding UT.
#### Why I did it
Back port GNMI to 202211 branch
#### How I did it
Update rules/config to enable host service
#### How to verify it
Run GNMI end2end test
Why I did it
If make fails, we can't rerun the make process, because existing patches can't apply again.
How I did it
Check if patches are applied. if yes, don't apply patches again.
How to verify it
Why I did it
There is a queue in sysmonitor.py that is created based on an object of multiprocessing.Manager.
After performing fast-reboot, system health monitor is being shut down, what causes this Manager to be shut down as well, since it is a child-process of healthd.
That's why I moved the creation of this Manager from the top of the file to the function Sysmonitor.system_service() (The only place it is used), to make Manager a child-process of Sysmonitor, instead of Healthd. This way both the queue (the Manager) and the processes that uses this queue will be child-processes of the same process, and the problematic scenario of sysmonitor sending messages to a dead queue will not be possible.
How I did it
Removed the definition of manager as global and moved it to system_service() function
How to verify it
Perform a fast reboot and verify the traceback issue is fixed
