Changes in the new release:
1. Policy based hashing optimization
2. New attribute support for Max port headroom
3. Tunnel ECN map fixes
4. Tunnel EVPN skeleton extensions (peer attrib, maps)
5. Bridge port admin not affecting port admin (optimize port down time)
6. CRM new API for neighbors and tunnel termination entries
7. Improve FDB event for flush by bridge port (before, null bridge was reported to SONiC, now the bridge will be extracted from bridge port)
8. DHCP L2 v4+v6 traps (for ZTP use case)
9. Generic counter implementation
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- combine docker-ptf-saithrift into docker-ptf docker
- build docker-ptf under platform vs
- remove docker-ptf for other platforms
Signed-off-by: Guohan Lu <lguohan@gmail.com>
During ISSU, "mlxsw_minimal" driver still trying to access firmware, in some cases FW could return some wrong critical threshold value which will cause switch shutdown.
**- How I did it**
In order to prevent "mlxsw_minimal" driver from accessing ASIC during ISSU, SDK will raise "OFFLINE" 'udev' event
at the early beginning of such flow. When this event is received, hw-management will remove "mlxsw_minimal" driver.
There is no need to implement the opposite "ONLINE" event since this flow is ended up with "kexec".
**- How to verify it**
repeatedly perform warm reboot, make sure there is no switch shutdown occurred.
Bugs fixes:
All | Kernel | During system reload when CPU is loaded with heavy traffic, a Kernel Panic may occur.
All | Modules, Port split | FW stuck when device rebooted with locked Optical Transceivers in split mode
Spectrum-3 | PFC | On Spectrum-3 systems, slow reaction time to Rx pause packets on 40GbE ports may lead to buffer overflow on servers.
Spectrum-3 | SN4700, Port Split | On rare occasion SN4700, conducting 100G split (4x25G) in NRZ when splitter port 1 or 2 are down, ports 3 and 4 will also go down.
Enahncments:
All | Kernel | new notification on ISSU start, so other kernel drivers can disable any interface to ASIC
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Check #6483
add test to make sure default route change in eth0 does not
affect the default route in the default vrf
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Fixes#6445
Because the ipmihelper.py script in the 9332 folder is slightly different than the common one (due to LGTM fixes), when the common one gets copied during build time it causes the workspace/build to become dirty.
Signed-off-by: Danny Allen <daall@microsoft.com>
- Why I did it
Initially, we used Monit to monitor critical processes in each container. If one of critical processes was not running
or crashed due to some reasons, then Monit will write an alerting message into syslog periodically. If we add a new process
in a container, the corresponding Monti configuration file will also need to update. It is a little hard for maintenance.
Currently we employed event listener of Supervisod to do this monitoring. Since processes in each container are managed by
Supervisord, we can only focus on the logic of monitoring.
- How I did it
We borrowed the event listener of Supervisord to monitor critical processes in containers. The event listener will take
following steps if it was notified one of critical processes exited unexpectedly:
The event listener will first check whether the auto-restart mechanism was enabled for this container or not. If auto-restart mechanism was enabled, event listener will kill the Supervisord process, which should cause the container to exit and subsequently get restarted.
If auto-restart mechanism was not enabled for this contianer, the event listener will enter a loop which will first sleep 1 minute and then check whether the process is running. If yes, the event listener exits. If no, an alerting message will be written into syslog.
- How to verify it
First, we need checked whether the auto-restart mechanism of a container was enabled or not by running the command show feature status. If enabled, one critical process should be selected and killed manually, then we need check whether the container will be restarted or not.
Second, we can disable the auto-restart mechanism if it was enabled at step 1 by running the commnad sudo config feature autorestart <container_name> disabled. Then one critical process should be selected and killed. After that, we will see the alerting message which will appear in the syslog every 1 minute.
- Which release branch to backport (provide reason below if selected)
201811
201911
[x ] 202006
**- Why I did it**
On the Mellanox platform, reboot cause is fetched from some certain sysfs which is created by the hw-management service. So determine-reboot-cause service shall start after hw-management, otherwise it could fail due to the related sysfs is not available yet.
**- How I did it**
Add a patch to the hw-management service to make sure determine-reboot-cause service should start after it.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
**- Why I did it**
- The thermalctld daemon on the Pmon docker requires support from the thermal manager API.
**- How I did it**
- Removed the old function for detecting a faulty fan.
- Removed the old function for detecting excess temperature.
- Implement thermal_manager APIs based on ThermalManagerBase
- Implement thermal_conditions APIs based on ThermalPolicyConditionBase
- Implement thermal_actions APIs based on ThermalPolicyActionBase
- Implement thermal_info APIs based on ThermalPolicyInfoBase
- Add thermal_policy.json
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
1. Fixes the missing DPKG file for gbsyncd-vs package
2. Fixes the softlink issue on the Platform-common and ztp package
3. Fixes the PYTHNON_DEBS list is missing for DBG dockers.
- Improve random number generation during early Sonic initialization by providing SW updates to Linux entropy value.
- Improve handling of platform In-Band management port
This commit provides the following updates to the Nokia ixs7215 platform
1. The Marvell Armada-38x SOC requires SW assistance to improve the system
entropy value available early on in the Sonic boot sequence.
2. The Nokia ixs7215 platform does not have a dedicated Out-Of-Band (OOB) mgmt
port and thus requires additional logic to optionally support configuring
front panel port 48 as an In-Band mgmt port. This commit provides additional
logic to manage and maintain the operation of this In-Band mgmt port.
fix platform driver breakage due to python3 upgrade and fix load minigraph errors with config load_minigraph -y
**- How I did it**
added python3-smbus to the pmon docker template since the previous was python2 specific
fixed additional "ord" python2 specific code
fixed the jinja templates used by qos reload - the template logic required data to be parsed
**- How to verify it**
run "show platform XXX" commands and verify output
run "sudo config load_minigraph -y" and verify configuration
run "show interfaces XXX" and verify output
Co-authored-by: Carl Keene <keene@nokia.com>
Centec syncd have beend upgraded to buster, docker-syncd-centec-rpc do not need generate stretch based docker.
Co-authored-by: Xianghong Gu <xgu@centecnetworks.com>
In rare case can see that xcvrd failed due to "UnboundLocalError: local variable 'label_port' referenced before assignment"
Init "label_port" as None at the beginning of the function, to avoid the case that "label_port" not assigned.
Fix#119
when parallel build is enable, multiple dpkg-buildpackage
instances are running at the same time. /var/lib/dpkg is shared
by all instances and the /var/lib/dpkg/updates could be corrupted
and cause the build failure.
the fix is to use overlay fs to mount separate /var/lib/dpkg
for each dpkg-buildpackage instance so that they are not affecting
each other.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* Enable telemetry for ARM64 by default
* [Centec]Upgrade Centec syncd docker to buster; libjemalloc2 have been installed in docker-base-buster, remove libjemalloc1 from docker-syncd-centec's Dockerfile.j2
Co-authored-by: Gu Xianghong <xgu@centecnetworks.com>
- Make PDDF code compliant with both Python 2 and Python 3
- Align code with PEP8 standards using autopep8
- Build and install both Python 2 and Python 3 PDDF packages
Starting from build (master) 176 the warm reboot on BRCM Platform started to experience syncd crash. Upon further debug by Ying it was determined that the crash was related to the following new change:
[Dynamic buffer calc] Support dynamic buffer calculation (#1338)
Ying also debugged further and found The crash was caused by buffer pool profile setting operation SAI_BUFFER_PROFILE_ATTR_SHARED_DYNAMIC_TH
A case has filed with BRCM while a potential fix was tried by Ying that seems to have addressed this issue and we are making this change available in master branch so that it will allow further feature validation/testing especially in the warm reboot area.
Once an official fix is provided by BRCM, we will then remove this in house fix and apply the official fix.
- How to verify it
Just perform warm reboot with any master code 175 or above you should see this issue or issue the following cmd will also cause the crash: "mmuconfig -p egress_lossy_profile -a 0"
- Dynamically change EEPROM driver based on media type.
- Otherwise, EEPROM INFO and DOM INFO might not be fetched properly and will result in erroneous output.
combine multiple same operation into one operation to reduce
the build steps. this is to avoid max depth exceeded issue
in the build.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Add a systemd dependency to make platform-modules service as a prerequisite for determine-reboot-cause service to ensure platform initialization is complete before determine-reboot-cause.service executes.
the control file version is 4.2.1.5-7
sonic$ sudo dpkg -i target/debs/buster/libsaibcm-dev_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm-dev_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm-dev (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm-dev (4.2.1.5-7) ...
lgh@491d842369cf:/sonic$ sudo dpkg -i target/debs/buster/libsaibcm_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm (4.2.1.5-7) ...
Processing triggers for libc-bin (2.28-10) ...
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
Features:
Spectrum-3 | Systems | Added GA-level support for SN4700 A0 system
All | Shared headroom | Added GA-level support for Shared headroom between PGs
Bugs fixes:
All | Counters | Sent traffic in certain size is wrongly increase to a smaller size counter, because port extended counter has a counter for sent traffic per packet-size range
All | Shared buffer | Configuring shared buffer on the fly may, on occasion, cause the chip to get stuck
Spectrum-2 | Modules | On occasion, link down is experienced with INPHI COLORZ PAM4 100G optic cables on SN3700 systems
- Why I did it
Make EEPROM platform APIs Python3 compliant in Nokia platform.
- How I did it
Handle bytearray type returned by read_eeprom and read_eeprom_bytes methods.
- How to verify it
Boot Nokia ixs7215 and verify PMON docker running and show platform syseeprom
Co-authored-by: Carl Keene <keene@nokia.com>
Introduce tunnel manager daemon. Start the process as part of swss container
Submodule update for swss:
9ed3026 - 2020-12-24 : [NAT] ACL Rule with DO_NOT_NAT action is getting failed. (#1502) [Akhilesh Samineni]
c39a4b1 - 2020-12-23 : Mux/IPTunnel orchagent changes (#1497) [Prince Sunny]
bc8df0e - 2020-12-23 : Add support for headroom pool watermark (#1567) [Neetha John]
**- Why I did it**
As part of migrating SONiC codebase from Python 2 to Python 3
**- How I did it**
- No longer install Python 2 in docker-base-buster or docker-config-engine-buster.
- Install Python 2 and pip2 in the following containers until we can completely eliminate it there:
- docker-platform-monitor
- docker-sonic-mgmt-framework
- docker-sonic-vs
- Pin pip2 version <21 where it is still temporarily needed, as pip version 21 will drop support for Python 2
- Also preform some other cleanup, ensuring that pip3, setuptools and wheel packages are installed in docker-base-buster, and then removing any attempts to re-install them in derived containers
* [Mellanox] Update SAI to 1.18.0
* [Mellanox] Update SDK to 4.4.2112
* Updated Mellanox SAI to 1.18.0.2
* Updated bcmsai debians to use SAI 1.7.1
* Updated Mellanox to use SAI 1.7.1
* Updated submodule sonic-sairedis using SAI 1.7.1
Co-authored-by: Vineet Mittal <vmittalmittal@microsoft.com>
Co-authored-by: Nazarii Hnydyn <nazariig@nvidia.com>
bug fix: #5914
Validated for tx_disable function of SFP+ on AS7312-54X, AS5812-54X, AS5712-54x, and AS5812-54x.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
- Why I did it
To upgrade brcm syncd to buster
- How I did it
Updated BCM SAI using kernel version 4.19.0-12 and debian 10 to support buster.
Updated syncd docker from stretch to buster in sonic-buildimage
- How to verify it
Ensured docker is running synd buster.
After upgrade, ensured all BGP peers and ip interfaces are up.
Ping to BGP neighbors is working fine.
Install the necessary python3 dependent packages to convert restore_neighbor.py
to support python3 as python2 is EOL. See: Azure/sonic-swss#1542
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
In marvell_et644m platform scripts, I have added a check to confirm the file availability before accessing it.
Signed-off-by: Sabareesh Kumar Anandan <sanandan@marvell.com>
**- Why I did it**
To support dynamic buffer calculation.
This PR also depends on the following PRs for sub modules
- [sonic-swss: [buffermgr/bufferorch] Support dynamic buffer calculation #1338](https://github.com/Azure/sonic-swss/pull/1338)
- [sonic-swss-common: Dynamic buffer calculation #361](https://github.com/Azure/sonic-swss-common/pull/361)
- [sonic-utilities: Support dynamic buffer calculation #973](https://github.com/Azure/sonic-utilities/pull/973)
**- How I did it**
1. Introduce field `buffer_model` in `DEVICE_METADATA|localhost` to represent which buffer model is running in the system currently:
- `dynamic` for the dynamic buffer calculation model
- `traditional` for the traditional model in which the `pg_profile_lookup.ini` is used
2. Add the tables required for the feature:
- ASIC_TABLE in platform/\<vendor\>/asic_table.j2
- PERIPHERAL_TABLE in platform/\<vendor\>/peripheral_table.j2
- PORT_PERIPHERAL_TABLE on a per-platform basis in device/\<vendor\>/\<platform\>/port_peripheral_config.j2 for each platform with gearbox installed.
- DEFAULT_LOSSLESS_BUFFER_PARAMETER and LOSSLESS_TRAFFIC_PATTERN in files/build_templates/buffers_config.j2
- Add lossless PGs (3-4) for each port in files/build_templates/buffers_config.j2
3. Copy the newly introduced j2 files into the image and rendering them when the system starts
4. Update the CLI options for buffermgrd so that it can start with dynamic mode
5. Fetches the ASIC vendor name in orchagent:
- fetch the vendor name when creates the docker and pass it as a docker environment variable
- `buffermgrd` can use this passed-in variable
6. Clear buffer related tables from STATE_DB when swss docker starts
7. Update the src/sonic-config-engine/tests/sample_output/buffers-dell6100.json according to the buffer_config.j2
8. Remove buffer pool sizes for ingress pools and egress_lossy_pool
Update the buffer settings for dynamic buffer calculation
python2 is end of life and SONiC is going to support python3. This PR is going to support:
1. Mellanox SONiC platform API python3 support
2. Install both python2 and python3 verson of Mellanox SONiC platform API or pmon and host side
- Enhance eeprom parsing robustness on corrupted fields
- Add chassis provisioning service
- Disable CPU sleep state on some systems
- Complete refactor for FanSlots
- Fix module unload while still in use
Barefoot platform vendors' sonic_platform packages import the Python 'thrift' library. Previously, our custom-built package was being installed in the PMon container and host OS. However, we are only building a Python 2 version of that package, which was only intended for use with saithrift.
Fixes#6077
Changes for supporting vstest for VOQ system ports. The changes include:
(1)Use of chassis_db.json is avoided since the SYSTEM_PORT is made
available in virtual chassis linecard's default_config.json which will
be loaded during bootup
(2)Core port index map file is introduced and is copied from virtual chassis
directory to hwsku direcory by start.sh
(3)vs sai profile is modified to include core port index map file name
Signed-off-by: vedganes <vedavinayagam.ganesan@nokia.com>
- Why I did it
For determining reboot-cause while running newer BIOS, SMF firmware.
- How I did it
Made changes in reboot-cause determination script to add support for behavior of newer firmware.
- How to verify it
Performed different type of resets and verified "show reboot-cause" provides the correct reason.
Logs: UT_logs.txt
- Description for the changelog
DellEMC S6100: Update reboot-cause determination to support new firmware
EEPROM cache file is not refreshed after install a new ONIE version even if the eeprom data is updated. The current Eeprom class always try to read from the cache file when the file exists. The PR is aimed to fix it.
- Change return type of SFP methods to match specification in sonic_platform_common/sfp_base.py
- Use init methods of base classes to initialize common instance variables
- Handle negative timeout values in S6100's watchdog ‘arm’ method
- Return appropriate values for 'get_target_speed', 'set_status_led' to avoid false warnings
- Implement platform module API
- Implement platform drawer API
- Complete and fix a few other platform API
- Add psu and fan support for chassis
- Fix dependency issue with determine-reboot-cause
* Update 50-ttyUSB-C0.rules
Remove some debug codes
* Update popmsg.sh
remove the debug info
* Update udev_prefix.sh
remove debug info
* Update platform-modules-haliburton.postinst
To enable the execute permission of udev scripts
* Update 50-ttyUSB-C0.rules
Fix port 13 - 48 plug out but not pop out message issue.
Signed-off-by: Jing Kan jika@microsoft.com
- Why I did it
Fix the i2c device to address conflicts behind the PCA9548 switch.
- How I did it
Load the i2c-mux-pca954x with parameter force-deselect-on-exit=1.
Submodule updates include the following commits:
* src/sonic-utilities 9dc58ea...f9eb739 (18):
> Remove unnecessary calls to str.encode() now that the package is Python 3; Fix deprecation warning (#1260)
> [generate_dump] Ignoring file/directory not found Errors (#1201)
> Fixed porstat rate and util issues (#1140)
> fix error: interface counters is mismatch after warm-reboot (#1099)
> Remove unnecessary calls to str.decode() now that the package is Python 3 (#1255)
> [acl-loader] Make list sorting compliant with Python 3 (#1257)
> Replace hard-coded fast-reboot with variable. And some typo corrections (#1254)
> [configlet][portconfig] Remove calls to dict.has_key() which is not available in Python 3 (#1247)
> Remove unnecessary conversions to list() and calls to dict.keys() (#1243)
> Clean up LGTM alerts (#1239)
> Add 'requests' as install dependency in setup.py (#1240)
> Convert to Python 3 (#1128)
> Fix mock SonicV2Connector in python3: use decode_responses mode so caller code will be the same as python2 (#1238)
> [tests] Do not trim from PATH if we did not append to it; Clean up/fix shebangs in scripts (#1233)
> Updates to bgp config and show commands with BGP_INTERNAL_NEIGHBOR table (#1224)
> [cli]: NAT show commands newline issue after migrated to Python3 (#1204)
> [doc]: Update Command-Reference.md (#1231)
> Added 'import sys' in feature.py file (#1232)
* src/sonic-py-swsssdk 9d9f0c6...1664be9 (2):
> Fix: no need to decode() after redis client scan, so it will work for both python2 and python3 (#96)
> FieldValueMap `contains`(`in`) will also work when migrated to libswsscommon(C++ with SWIG wrapper) (#94)
- Also fix Python 3-related issues:
- Use integer (floor) division in config_samples.py (sonic-config-engine)
- Replace print statement with print function in eeprom.py plugin for x86_64-kvm_x86_64-r0 platform
- Update all platform plugins to be compatible with both Python 2 and Python 3
- Remove shebangs from plugins files which are not intended to be executable
- Replace tabs with spaces in Python plugin files and fix alignment, because Python 3 is more strict
- Remove trailing whitespace from plugins files
Some syncd containers are still based on Debian Stretch, and thus do not have Python 3 available. For these containers, we must still rely on Python 2 to run supervisord_dependent_startup and supervisor-proc-exit-listener.
Fix 259 alerts reported by the LGTM tool:
- 245 for Unused import
- 7 for Testing equality to None
- 5 for Duplicate key in dict literal
- 1 for Module is imported more than once
- 1 for Unused local variable
**- Why I did it**
We were building a custom version of Supervisor because I had added patches to prevent hangs and crashes if the system clock ever rolled backward. Those changes were merged into the upstream Supervisor repo as of version 3.4.0 (http://supervisord.org/changes.html#id9), therefore, we should be able to simply install the vanilla package via pip. This will also allow us to easily move to Python 3, as Python 3 support was added in version 4.0.0.
**- How I did it**
- Remove Makefiles and patches for building supervisor package from source
- Install Python 3 supervisor package version 4.2.1 in Buster base container
- Also install Python 3 version of supervisord-dependent-startup in Buster base container
- Debian package installed binary in `/usr/bin/`, but pip package installs in `/usr/local/bin/`, so rather than update all absolute paths, I changed all references to simply call `supervisord` and let the system PATH find the executable to prevent future need for changes just in case we ever need to switch back to build a Debian package, then we won't need to modify these again.
- Install Python 2 supervisor package >= 3.4.0 in Stretch and Jessie base containers
We are facing some compilation issue while compiling mgmt framework for arm.
So, disabling Mgmt framework for marvell-armhf. We will enable it after fixing the compilation issues
Signed-off-by: Sabareesh Kumar Anandan <sanandan@marvell.com>
This release includes changes for supporting Debian Buster, fixes for internally found issues and more enhancement related to spec coverage and feature parity for Broadcom ASICs.
Additional fixes included:
CS00011465498 - Warm reboot
CS00011465061 - interfaces not coming up
CS00011396506 - nexthop resource leak
CS00011452080 - BCM SAI crash while getting lane count
In order to support SONiC physical entity mib extension, a few new platform API are added to sonic-platform-common, this PR is to provide an mellanox platform implementation for those new APIs.
* LIBSAIREDIS isn't depend on CENTEC_SAI remove this dependence
* Build depends are optimized in PR #4880 and #5039. Merge these optimization to Centec ARM64 platform.
pick up new functions and bug fixes:
- New Features
- Add dynamic minimum tables for MSN3700X, MSN3800, MSN3420, MSN4600, MSN4700 systems
- Split hw-management to one-shot init hw-management service and thermal control services.
- Bug fixes
HW Mgmt core:
- Move PSU EEPROM configuration from kernel to user space for Spectrum 2 / Spectrum 3 system
This change introduces PDDF which is described here: https://github.com/Azure/SONiC/pull/536
Most of the platform bring up effort goes in developing the platform device drivers, SONiC platform APIs and validating them. Typically each platform vendor writes their own drivers and platform APIs which is very tailor made to that platform. This involves writing code, building, installing it on the target platform devices and testing. Many of the details of the platform are hard coded into these drivers, from the HW spec. They go through this cycle repetitively till everything works fine, and is validated before upstreaming the code.
PDDF aims to make this platform driver and platform APIs development process much simpler by providing a data driven development framework. This is enabled by:
JSON descriptor files for platform data
Generic data-driven drivers for various devices
Generic SONiC platform APIs
Vendor specific extensions for customisation and extensibility
Signed-off-by: Fuzail Khan <fuzail.khan@broadcom.com>
* [Juniper] Platform bug fixes / improvements
This patch set introduces the following changes for
the two platforms.
- QFX5210
- Fixes a driver bug related to reboot notifier
- Disable pcied
- Introduces a wrapper script for fast / warm reboots
for unloading the driver containing reboot handler
- Support for PSM4 optics in media_settings
- QFX5200
- BCM configuration file updates
- Bug fixes for EM policy
- Fixes a driver bug related to reboot notifier
- Introduces a wrapper script for fast / warm reboots
for unloading the driver containing reboot handler
- Disable pcied
- Support for PSM4 optics
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
In case of non-GA SDK version there is '-' symbol in Mellanox SDK version name. (For example: 4.4.1306-006)
In appropriate .deb packet there is '.' instead of '-'. Because of this there was problem while building SDK
Signed-off-by: Andriy Yurkiv <ayurkiv@nvidia.com>
The original code tried to initialize PCA9541 without having the
driver loaded. As result the initialization didn't take effect.
Recently PCA9541 driver was added to the kernel and since then
the initialization takes effect and has negatively impacted the
platform stability.
Commenting the initialization code out to restore the original
behavior while analyzing further.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
New driver support fetching additional pages from the cable EEPROM.
There are additional information to parse now: RX/TX power, TX bias, TX fault and RX LOS.
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
Prevent intermittent build failures when building Sonic for the ARM platform architecture due to version upgrades of the redis-tools and redis-server packages.
Modify select Dockerfile templates to download the redis-tools and redis-server packages from sonicstorage rather than from debian.org.
This PR has been made possible by the inclusion of ARM versions of redis-tools and redis-server into sonicstorage as described in Issue# 5701
Why/How I did:
Make sure first error syslog is triggered based on FAULT TOLERANCE condition.
Added support of repeat clause with alert action. This is used as trigger
for generation of periodic syslog error messages if error is persistent
Updated the monit conf files with repeat every x cycles for the alert action
- Change `/run/arista` mount to pmon by `/var/run/platform_cache`
- Python3 by default for Arista platform initialisation
- Fix outstanding py2/3 compatibility issues (eeprom mostly)
- Use pytest for unit testing
- Miscellaneous modular fixes
- Implement FanDrawer and get_high_critical_threshold Platform API for S6000, S6100, Z9100 and Z9264F.
- Fix incorrect fan direction values in S6100, Z9100
The orchagent and syncd need to have the same default synchronous mode configuration. This PR adds a template file to translate the default value in CONFIG_DB (empty field) to an explicit mode so that the orchagent and syncd could have the same default mode.
When detecting a new SFP insertion, read its SFP type and DOM capability from EEPROM again.
SFP object will be initialized to a certain type even if no SFP present. A case could be:
1. A SFP object is initialized to QSFP type by default when there is no SFP present
2. User insert a SFP with an adapter to this QSFP port
3. The SFP object fail to read EEPROM because it still treats itself as QSFP.
This PR fixes this issue.
- Enable thermalctld support for our platforms
- Fix Chassis.get_num_sfp which had an off by one
- Implement read_eeprom and write_eeprom in SfpBase
- Refactor of Psus and PsuSlots. Psus they are now detected and metadata reported
- Improvements to modular support
Co-authored-by: Zhi Yuan Carl Zhao <zyzhao@arista.com>
**- Why I did it**
Install all host services and their data files in package format rather than file-by-file
**- How I did it**
- Create sonic-host-services Python wheel package, currently including procdockerstatsd
- Also add the framework for unit tests by adding one simple procdockerstatsd test case
- Create sonic-host-services-data Debian package which is responsible for installing the related systemd unit files to control the services in the Python wheel. This package will also be responsible for installing any Jinja2 templates and other data files needed by the host services.
Now we are reading base mac, product name from eeprom data, and the data read from eeprom contains multiple "\0" characters at the end, need trim them to make the string clean and display correct.
The `get_serial_number()` method in the ChassisBase and ModuleBase classes was redundant, as the `get_serial()` method is inherited from the DeviceBase class. This method was removed from the base classes in sonic-platform-common and the submodule was updated in https://github.com/Azure/sonic-buildimage/pull/5625.
This PR aligns the existing vendor platform API implementations to remove the `get_serial_number()` methods and ensure the `get_serial()` methods are implemented, if they weren't previously.
Note that this PR does not modify the Dell platform API implementations, as this will be handled as part of https://github.com/Azure/sonic-buildimage/pull/5609
Example of syslog message from Mellanox SAI:
"Oct 7 15:39:11.482315 arc-switch1025 INFO syncd#supervisord: syncd Oct 07 15:39:11 NOTICE SAI_BUFFER: mlnx_sai_buffer.c[3893]- mlnx_clear_buffer_pool_stats: Clear pool stats pool id:1"
There is a log INFO from supervisord which actually printed NOTICE and
date again. This confusion happens becuase if SAI is not built to log
to syslog it will log everything to stdout with format "[date] [level]
[message]" so supervisord sends it to syslog with level INFO.
New logs look like:
"Oct 7 15:40:21.488055 arc-switch1025 NOTICE syncd#SDK [SAI_BUFFER]: mlnx_sai_buffer.c[3893]- mlnx_clear_buffer_pool_stats: Clear pool stats pool id:17"
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
- Make DellEMC platform modules Python3 compliant.
- Change return type of PSU Platform APIs in DellEMC Z9264, S5232 and Thermal Platform APIs in S5232 to 'float'.
- Remove multiple copies of pcisysfs.py.
- PEP8 style changes for utility scripts.
- Build and install Python3 version of sonic_platform package.
- Fix minor Platform API issues.
- The issue is that the SAI package content is changed without changing its version. The DPKG caches the wrong version of SAI package.
- The fix is to include the SAI package content header for SHA calcaulation. This will detect if there is any change in the SAI package.
It should no longer be necessary to explicitly install the 'wheel' package, as SONiC packages built as wheels should specify 'wheel' as a dependency in their setup.py files. Therefore, pip[3] should check for the presence of 'wheel' and install it if it isn't present before attempting to call 'setup.py bdist_wheel' to install the package.
bring up chassisdb service on sonic switch according to the design in
Distributed Forwarding in VoQ Arch HLD
Signed-off-by: Honggang Xu <hxu@arista.com>
**- Why I did it**
To bring up new ChassisDB service in sonic as designed in ['Distributed forwarding in a VOQ architecture HLD' ](90c1289eaf/doc/chassis/architecture.md).
**- How I did it**
Implement the section 2.3.1 Global DB Organization of the VOQ architecture HLD.
**- How to verify it**
ChassisDB service won't start without chassisdb.conf file on the existing platforms.
ChassisDB service is accessible with global.conf file in the distributed arichitecture.
Signed-off-by: Honggang Xu <hxu@arista.com>
We were building our own python-click package because we needed features/bug fixes available as of version 7.0.0, but the most recent version available from Debian was in the 6.x range.
"Click" is needed for building/testing and installing sonic-utilities. Now that we are building sonic-utilities as a wheel, with Click specified as a dependency in the setup.py file, setuptools will install a more recent version of Click in the sonic-slave-buster container when building the package, and pip will install a more recent version of Click in the host OS of SONiC when installing the sonic-utilities package. Also, we don't need to worry about installing the Python 2 or 3 version of the package, as the proper one will be installed as necessary.
- SN3800 vs Cisco9236 - no link copper or optics - start sending IDLE before PHY_UP for specific OPNs
Signed-off-by: Nazarii Hnydyn <nazariig@nvidia.com>
During platform deinitialization, dell_ich is not removed properly and when we do initialize s6100 platform, ICH driver sysfs attributes are not attached. Because of this, get_transceiver_change_event returns error and this leads xcvrd to crash.
Make Python3-swsscommon available in image.
```
admin@str-s6000-acs-13:~$ sudo apt-cache search swss
libswsscommon - This package contains Switch State Service common library.
python-swsscommon - This package contains Switch State Service common Python2 library.
python3-swsscommon- This package contains Switch State Service common Python3 library.
admin@str-s6000-acs-13:~$
```
Some platforms don't leverage the brcm led coprocessor.
However ledinit will try to load a non existing file and exit with an
error code.
This change is a cosmetic fix mostly.
- How to verify it
Boot a platform without the configuration and verify in the syslog that the exit status of ledinit is 0
Boot a platform with the configuration and verify in the syslog that the exit status of ledinit is 0 and the leds are working.
Verified by adding a dumb led_proc_init.soc on an Arista platform which usually doesn't use it.
**- Why I did it**
- Platform API implementation using sonic-cfggen to get platform name and SKU name, which will fail when the database is not available.
- Chassis name is not correctly assigned, it shall be assigned with EEPROM TLV "Product Name", instead of SKU name
- Chassis model is not implemented, it shall be assigned with EEPROM TLV "Part Number"
**- How I did it**
1. Chassis
> - Get platform name from /host/machine.conf
> - Remove get SKU name with sonic-cfggen
> - Get Chassis name and model from EEPROM TLV "Product Name" and "Part Number"
> - Add function to return model
2. EEPROM
> - Add function to return product name and part number
3. Platform
> - Init EEPROM on the host side, so also can get the Chassis name model from EEPROM on the host side.
* buildimage: Add gearbox phy device files and a new physyncd docker to support VS gearbox phy feature
* scripts and configuration needed to support a second syncd docker (physyncd)
* physyncd supports gearbox device and phy SAI APIs and runs multiple instances of syncd, one per phy in the device
* support for VS target (sonic-sairedis vslib has been extended to support a virtual BCM81724 gearbox PHY).
HLD is located at b817a12fd8/doc/gearbox/gearbox_mgr_design.md
**- Why I did it**
This work is part of the gearbox phy joint effort between Microsoft and Broadcom, and is based
on multi-switch support in sonic-sairedis.
**- How I did it**
Overall feature was implemented across several projects. The collective pull requests (some in late stages of review at this point):
https://github.com/Azure/sonic-utilities/pull/931 - CLI (merged)
https://github.com/Azure/sonic-swss-common/pull/347 - Minor changes (merged)
https://github.com/Azure/sonic-swss/pull/1321 - gearsyncd, config parsers, changes to orchargent to create gearbox phy on supported systems
https://github.com/Azure/sonic-sairedis/pull/624 - physyncd, virtual BCM81724 gearbox phy added to vslib
**- How to verify it**
In a vslib build:
root@sonic:/home/admin# show gearbox interfaces status
PHY Id Interface MAC Lanes MAC Lane Speed PHY Lanes PHY Lane Speed Line Lanes Line Lane Speed Oper Admin
-------- ----------- --------------- ---------------- --------------- ---------------- ------------ ----------------- ------ -------
1 Ethernet48 121,122,123,124 25G 200,201,202,203 25G 204,205 50G down down
1 Ethernet49 125,126,127,128 25G 206,207,208,209 25G 210,211 50G down down
1 Ethernet50 69,70,71,72 25G 212,213,214,215 25G 216 100G down down
In addition, docker ps | grep phy should show a physyncd docker running.
Signed-off-by: syd.logan@broadcom.com
We want to let Monit to unmonitor the processes in containers which are disabled in `FEATURE` table such that
Monit will not generate false alerting messages into the syslog.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
libzmq5 is tcp/ipc communication library, needed by sairedis/syncd to communicate, as a new way (compared to current REDIS channel) to exchange messages which is faster than REDIS library and allows synchronous mode
this library is required in sairedis repo, swss repo, sonic-buildimage and sonic-build-tools to make it work
- Why I did it
For fixing PCA MUX attachment issue in Dell S6100 platform.
- How I did it
Wait till IOM MUX powered up properly and start I2C enumeration.
We are moving toward building all Python packages for SONiC as wheel packages rather than Debian packages. This will also allow us to more easily transition to Python 3.
Python files are now packaged in "sonic-utilities" Pyhton wheel. Data files are now packaged in "sonic-utilities-data" Debian package.
**- How I did it**
- Build and install sonic-utilities as a Python package
- Remove explicit installation of wheel dependencies, as these will now get installed implicitly by pip when installing sonic-utilities as a wheel
- Build and install new sonic-utilities-data package to install data files required by sonic-utilities applications
- Update all references to sonic-utilities scripts/entrypoints to either reference the new /usr/local/bin/ location or remove absolute path entirely where applicable
Submodule updates:
* src/sonic-utilities aa27dd9...2244d7b (5):
> Support building sonic-utilities as a Python wheel package instead of a Debian package (#1122)
> [consutil] Display remote device name in show command (#1120)
> [vrf] fix check state_db error when vrf moving (#1119)
> [consutil] Fix issue where the ConfigDBConnector's reference is missing (#1117)
> Update to make config load/reload backward compatible. (#1115)
* src/sonic-ztp dd025bc...911d622 (1):
> Update paths to reflect new sonic-utilities install location, /usr/local/bin/ (#19)
This PR limited the number of calls to sonic-cfggen to one call
per iteration instead of current 3 calls per iteration.
The PR also installs jq on host for future scripts if needed.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Refactor SFP reset, low power get/set API, and plugins with new SDK SX APIs. Previously they were calling SDK SXD APIs which have glibc dependency because of shared memory usage.
Remove implementation "set_power_override", "tx_disable_channel", "tx_disable" which using SXD APIs, once related SDK SX API available, will add them back based on new SDK SX APIs.
- Merge chassis codebase upstream
- Add support for Otterlake supervisor
- Add support for NorthFace and Camp chassis
- Add support for Eldridge, Dragonfly and Brooks fabrics
- Add support for Clearwater2 and Clearwater2Ms linecards
- Add new arista Cli to power on/off cards
- Add new arista show Cli to inspect supervisor, chassis, fabrics and linecards
- Finish the refactor of the smbus backend (huge performance enhencement)
- Split scd-hwmon kernel module in multiple source files
- Add new scd-uart driver to manage linecard consoles within a chassis
- Bootstrap of thermal platform API implementation
- Fix psud led error message
- Fix fan led color on Smartsville
When stopping the swss, pmon or bgp containers, log messages like the following can be seen:
```
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,061 ERRO pool dependent-startup event buffer overflowed, discarding event 34
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,063 ERRO pool dependent-startup event buffer overflowed, discarding event 35
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,064 ERRO pool dependent-startup event buffer overflowed, discarding event 36
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,066 ERRO pool dependent-startup event buffer overflowed, discarding event 37
```
This is due to the number of programs in the container managed by supervisor, all generating events at the same time. The default event queue buffer size in supervisor is 10. This patch increases that value in all containers in order to eliminate these errors. As more programs are added to the containers, we may need to further adjust these values. I increased all buffer sizes to 25 except for containers with more programs or templated supervisor.conf files which allow for a variable number of programs. In these cases I increased the buffer size to 50. One final exception is the swss container, where the buffer fills up to ~50, so I increased this buffer to 100.
Resolves https://github.com/Azure/sonic-buildimage/issues/5241
* [redis] Use redis-server and redis-tools in blob storage to prevent
upstream link broken
* Use curl instead of wget
* Explicitly install dependencies
Copying platform.json file into an empty /usr/share/sonic/platform directory does not mimic an actual device. A more correct approach is to create a /usr/share/sonic/platform symlink which links to the actual platform directory; this is more like what is done inside SONiC containers. Then, we only need to copy the platform.json file into the actual platform directory; the symlink takes care of the alternative path, and also exposes all the other files in the platform directory.
sonic-py-common package relies on the `PLATFORM` environment variable to be set at runtime in the SONiC VS container. Exporting the variables in the start.sh script causes the variables to only be available to the shell running start.sh and any subshells it spawns. However, once the script exits, the variable is lost. This is resulting in the failure of tests which are run in the VS container, as they call applications which in turn call sonic-py-common functions which rely on PLATFORM to be set.
Setting the environment variables in the Dockerfile allows them to persist through the entire runtime of the container.
Add a master switch so that the sync/async mode can be configured.
Example usage of the switch:
1. Configure mode while building an image
`make ENABLE_SYNCHRONOUS_MODE=y <target>`
2. Configure when the device is running
Change CONFIG_DB with `sonic-cfggen -a '{"DEVICE_METADATA":{"localhost": {"synchronous_mode": "enable"}}}' --write-to-db`
Restart swss with `systemctl restart swss`
- Reverts commit 457674c
- Creates "platform.json" for vs docker
- Adds test case for port breakout CLI
- Explicitly sets admin status of all the VS interfaces to down to be compatible with SWSS test cases, specifically vnet tests and sflow tests
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
As part of migrating all Python-based package installers to wheel format rather than Debian packages. Also to allow for easily building a Python 3 version of the package in the near future.
- Also remove some references to sonic-daemon-base which I previously missed and add missing sonic-py-common dependency for sonic-pcied.
Original converting from register is wrong, it makes the fan speed much higher than it is. Change the way fan speed is calculated from CPLD.
Signed-off-by: roy_lee <roy_lee@accton.com>
HW set qsfp port to reset at default. so need SW to set to normal when boot.
1. Modify cpld driver to invert reset offset value
2. Set to normal when boot.
Swap order of orchagent and portsyncd in start.sh and fix priorities
Many docker virtual switch tests are failing at the moment because orchagent never finishes initializing. After doing some searching I figured out that Ethernet24 is never published to State DB, which is reminiscent of #4821
Signed-off-by: Danny Allen <daall@microsoft.com>
summary of E530 platfrom:
- CPU: CTC5236, arm64
- LAN switch chip set: CENTEC CTC7132 (TsingMa). TsingMa is a purpose built device to address the challenge in the recent network evolution such as Cloud computing. CTC7132 provides 440Gbps I/O bandwidth and 400Gcore bandwidth, the CTC7132 family combines a feature-rich switch core and an embedded ARM A53 CPU Core running at 800MHz/1.2GHz. CTC7132 supports a variety of port configurations, such as QSGMII and USXGMII-M, providing full-rate port capability from 100M to 100G.
- device E530-48T4X: 48 * 10/100/1000 Base-T Ports, 4 * 10GE SFP+ Ports.
- device E530-24X2C: 24 * 10 GE SFP+ Ports, 2 * 100GE QSFP28 Ports.
add new files in three directories:
device/centec/arm64-centec_e530_24x2c-r0
device/centec/arm64-centec_e530_48t4x_p-r0
platform/centec-arm64
Co-authored-by: taocy <taocy2@centecnetworks.com>
Co-authored-by: Gu Xianghong <gxh2001757@163.com>
Co-authored-by: shil <shil@centecnetworks.com>
1. remove container feature table
2. do not generate feature entry if the feature is not included
in the image
3. rename ENABLE_* to INCLUDE_* for better clarity
4. rename feature status to feature state
5. [submodule]: update sonic-utilities
* 9700e45 2020-08-03 | [show/config]: combine feature and container feature cli (#1015) (HEAD, origin/master, origin/HEAD) [lguohan]
* c9d3550 2020-08-03 | [tests]: fix drops_group_test failure on second run (#1023) [lguohan]
* dfaae69 2020-08-03 | [lldpshow]: Fix input device is not a TTY error (#1016) [Arun Saravanan Balachandran]
* 216688e 2020-08-02 | [tests]: rename sonic-utilitie-tests to tests (#1022) [lguohan]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* Moving BRCM SAI from 3.7.5.1-1 to 3.7.5.1-2 to pick up the stubbed SAI API that were present in the header but missing in SAI implementation that cause link error during build.
In SAI header 1.5.2 there are defined SAI APIs such as "sai_query_attribute_capability()" and few other APIs that were missing the stub code in BRCM 3.7.5.1 SAI code delivery. This causes linking issue during build when we implemented the common handler to support "sai_query_attribute_capability()" that other platform supports. The expectation is that all SAI vendors must implement all the SAI header defined SAI APIs by stubbing those that they don't have the actual code support to return "SAI_STATUS_NOT_IMPLEMENTED". This allows common code for all platforms to be developed without having linking issue during build for all platforms. BRCM has provided the patch code and this PR moves the BRCM SAI from 3.7.5.1-1 to 3.7.5.1-2 to pick up those missing stubbed SAI APIs.
See BRCM case CS00010790550 for more details
Applications running in the host OS can read the platform identifier from /host/machine.conf. When loading configuration, sonic-config-engine *needs* to read the platform identifier from machine.conf, as it it responsible for populating the value in Config DB.
When an application is running inside a Docker container, the machine.conf file is not accessible, as the /host directory is not mounted. So we need to retrieve the platform identifier from Config DB if get_platform() is called from inside a Docker
container. However, we can't simply check that we're running in a Docker container because the host OS of the SONiC virtual switch is running inside a Docker container. So I refactored `get_platform()` to:
1. Read from the `PLATFORM` environment variable if it exists (which is defined in a virtual switch Docker container)
2. Read from machine.conf if possible (works in the host OS of a standard SONiC image, critical for sonic-config-engine at boot)
3. Read the value from Config DB (needed for Docker containers running in SONiC, as machine.conf is not accessible to them)
- Also fix typo in daemon_base.py
- Also changes to align `get_hwsku()` with `get_platform()`
- Created the VS setup to test DPB functionality
- Created "platform.json" for VS docker
- Added test case for Breakout CLI
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
As part of consolidating all common Python-based functionality into the new sonic-py-common package, this pull request:
1. Redirects all Python applications/scripts in sonic-buildimage repo which previously imported sonic_device_util or sonic_daemon_base to instead import sonic-py-common, which was added in https://github.com/Azure/sonic-buildimage/pull/5003
2. Replaces all calls to `sonic_device_util.get_platform_info()` to instead call `sonic_py_common.get_platform()` and removes any calls to `sonic_device_util.get_machine_info()` which are no longer necessary (i.e., those which were only used to pass the results to `sonic_device_util.get_platform_info()`.
3. Removes unused imports to the now-deprecated sonic-daemon-base package and sonic_device_util.py module
This is the next step toward resolving https://github.com/Azure/sonic-buildimage/issues/4999
Also reverted my previous change in which device_info.get_platform() would first try obtaining the platform ID string from Config DB and fall back to gathering it from machine.conf upon failure because this function is called by sonic-cfggen before the data is in the DB, in which case, the db_connect() call will hang indefinitely, which was not the behavior I expected. As of now, the function will always reference machine.conf.
* [platform] Add Support For Environment Variable
This PR adds the ability to read environment file from /etc/sonic.
the file contains immutable SONiC config attributes such as platform,
hwsku, version, device_type. The aim is to minimize calls being made
into sonic-cfggen during boot time.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
virtual-chassis test uses multiple vs instances to simulate a
modular switch and a redis-chassis service is required to run on
the vs instance that represents a supervisor card.
This change allows vs docker start redis-chassis service according
to external config file.
**- Why I did it**
To support virtual-chassis setup, so that we can test distributed forwarding feature in virtual sonic environment, see `Distributed forwarding in a VOQ architecture HLD` pull request at https://github.com/Azure/SONiC/pull/622
**- How I did it**
The sonic-vs start.sh is enhanced to start new redis_chassis service if external chassis config file found. The config file doesn't exist in current vs environment, start.sh will behave like before.
**- How to verify it**
The swss/test still pass. The chassis_db service is verified in virtual-chassis topology and tests which are in following PRs.
Signed-off-by: Honggang Xu <hxu@arista.com>
(cherry picked from commit c1d45cf81ce3238be2dcbccae98c0780944981ce)
Co-authored-by: Honggang Xu <hxu@arista.com>
when parallel build is enabled, both docker-fpm-frr and docker-syncd-brcm
is built at the same time, docker-fpm-frr requires swss which requires to
install libsaivs-dev. docker-syncd-brcm requires syncd package which requires
to install libsaibcm-dev.
since libsaivs-dev and libsaibcm-dev install the sai header in the same
location, these two packages cannot be installed at the same time. Therefore,
we need to serialize the build between these two packages. Simply uninstall
the conflict package is not enough to solve this issue. The correct solution
is to have one package wait for another package to be uninstalled.
For example, if syncd is built first, then it will install libsaibcm-dev.
Meanwhile, if the swss build job starts and tries to install libsaivs-dev,
it will first try to query if libsaibcm-dev is installed or not. if it is
installed, then it will wait until libsaibcm-dev is uninstalled. After syncd
job is finished, it will uninstall libsaibcm-dev and swss build job will be
unblocked.
To solve this issue, _UNINSTALLS is introduced to uninstall a package that
is no longer needed and to allow blocked job to continue.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Consolidate common SONiC Python-language functionality into one shared package (sonic-py-common) and eliminate duplicate code.
The package currently includes three modules:
- daemon_base
- device_info
- logger
Added required packages to enabled YANG dependency check for Dynamic Port Breakout in VS container.
[sonic-utilities PR #766](https://github.com/Azure/sonic-utilities/pull/766) has a dependency on it.
Getting error like the following without this fix: `ImportError: No module named yang - required module not found`
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
the command kills all exabgp processes on the host.
since the namespaces are newly added, there should
be no prior exabgp processes.
if it is existing namespace, it is also the dvs
framework job to clean up all prior processes.
Align SFP key names with new standard defined in https://github.com/Azure/sonic-platform-common/pull/97
- hardwarerev -> hardware_rev
- serialnum -> serial
- manufacturename -> manufacturer
- modelname -> model
- Connector -> connector
Added xmltodict and jsondiff packages needed to run vs test cases successfully for DPB.
sonic-utilities PR #766 has a dependency on these packages.
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
1) Fixing the issues while applying platform TxCTLE settings in sfputil.py for QFX5200
2) Adding the support for transceiver dom threshold info in sfputil.py for both QFX5210 & QFX5200 platforms
3) Updating the sfputil.py for QFX5210 & QFX5200 platforms
4) Adding a new platform specific command 'show_thresholds' to display the FAN dutycycle percentage for various temperature ranges (for both AFI & AFO QFX5200 systems).
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
System health feature needs to set/get system led status
- Add a led object in chassis class and initialize it when the API is called on host side
- Read/write system led system fs to get/set the status
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
This PR has changes to support accessing the bcmsh and bcmcmd utilities on multi ASIC devices
Changes done
- move the link of /var/run/sswsyncd from docker-syncd-brcm.mk to docker_image_ctl.j2
- update the bcmsh and bcmcmd scripts to take -n [ASIC_ID] as an argument on multi ASIC platforms
- Xilinx/pericom peripherals are not actively used in DellEMC S6100 switch.
- These peripherals are throwing PCIE corrected messages in some of the units and filling syslog.
- Since it is not usable disabling it at startup.
make swss build depends only on libsairedis instead of syncd. This allows to build swss without depending
on vendor sai library.
Currently, libsairedis build also buils syncd which requires vendor SAI lib. This makes difficult to build
swss docker in buster while still keeping syncd docker in stretch, as swss requires libsairedis which also
build syncd and requires vendor to provide SAI for buster. As swss docker does not really contain syncd
binary, so it is not necessary to build syncd for swss docker.
* [submodule]: update sonic-sairedis
* ccbb3bc 2020-06-28 | add option to build without syncd (HEAD, origin/master, origin/HEAD) [Guohan Lu]
* 4247481 2020-06-28 | install saidiscovery into syncd package [Guohan Lu]
* 61b8e8e 2020-06-26 | Revert "sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624)" (#630) [Danny Allen]
* 85e543c 2020-06-26 | add a README to tests directory to describe how to run 'make check' (#629) [Syd Logan]
* 2772f15 2020-06-26 | sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624) [Syd Logan]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
1. Upgrade SAI headers to v1.6.3
2. Fix traffic lost during FFB related to buffer config + optimize buffer config timing for FB
3. Add ACL fields BTH, IP flags
4. Add ACL infrastructure of different fields per ASIC type
**- Why I did it**
System health feature requires to read ASIC temperature and threshold from platform API
**- How I did it**
Implement Chassis.get_asic_temperature and Chassis.get_asic_temperature_threshold by getting value from system fs.
This patch addresses the following issues:
1) Platform drivers were not loading in the latest images. Fixed
the intialization script to make sure that all the drivers are
loaded.
2) Getting rid of "pstore: crypto_comp_decompress failed, ret = -22!"
messages during the kernel boot, after moving to 4.19 kernel. The
solution is to remove the files under '/sys/fs/pstore' directory.
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
**- Why I did it**
Initially, the critical_processes file contains either the name of critical process or the name of group.
For example, the critical_processes file in the dhcp_relay container contains a single group name
`isc-dhcp-relay`. When testing the autorestart feature of each container, we need get all the critical
processes and test whether a container can be restarted correctly if one of its critical processes is
killed. However, it will be difficult to differentiate whether the names in the critical_processes file are
the critical processes or group names. At the same time, changing the syntax in this file will separate the individual process from the groups and also makes it clear to the user.
Right now the critical_processes file contains two different kind of entries. One is "program:xxx" which indicates a critical process. Another is "group:xxx" which indicates a group of critical processes
managed by supervisord using the name "xxx". At the same time, I also updated the logic to
parse the file critical_processes in supervisor-proc-event-listener script.
**- How to verify it**
We can first enable the autorestart feature of a specified container for example `dhcp_relay` by running the comman `sudo config container feature autorestart dhcp_relay enabled` on DUT. Then we can select a critical process from the command `docker top dhcp_relay` and use the command `sudo kill -SIGKILL <pid>` to kill that critical process. Final step is to check whether the container is restarted correctly or not.
**- Why I did it**
After discussed with Joe, we use the string "/usr/bin/syncd\s" in Monit configuration file to monitor
syncd process on Broadcom and Mellanox. Due to my careless, I did not find this bug during the
previous testing. If we use the string "/usr/bin/syncd" in Monit configuration file to monitor the
syncd process, Monit will not detect whether syncd process is running or not.
If we ran the command `sudo monit procmactch “/usr/bin/syncd”` on Broadcom, there will be three
processes in syncd container which matched this "/usr/bin/syncd": `/bin/bash /usr/bin/syncd.sh
wait`, `/usr/bin/dsserve /usr/bin/syncd –diag -u -p /etc/sai.d/sai.profile` and `/usr/bin/syncd –diag -
u -p /etc/sai.d/said.profile`. Monit will select the processes with the highest uptime (at there
`/bin/bash /usr/bin/syncd.sh wait`) to match and did not select `/usr/bin/syncd –diag -u -p
/etc/sai.d/said.profile` to match.
Similarly, On Mellanox Monit will also select the process with the highest uptime (at there
`/bin/bash /usr/bin/syncd.sh wait`) to match and did not select `/usr/bin/syncd –diag -u -p
/etc/sai.d/said.profile` to match.
That is why Monit is unable to detect whether syncd process is running or not if we use the string “/usr/bin/syncd” in Monit configuration file. If we use the string "/usr/bin/syncd\s" in Monit configuration file, Monit can filter out the process `/bin/bash /usr/bin/syncd.sh wait` and thus can correctly monitor the syncd process.
**- How I did it**
**- How to verify it**
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Change port index in port_config.ini to 1-based
* Add default port index to port_config.ini, change platform plugins to accept 1-based port index
* fix port index in sfp_event.py
**- Why I did it**
The tx_disable function isn't work for the accton_ax5835-54x device.
**- How I did it**
Fix the incorrect path of the sfp node path inside the util file.
**- How to verify it**
Test with
"sudo accton_as5835_54x_util.py show"
"sudo accton_as5835_54x_util.py set sfp"
There should see correct value for module_present and module_tx_disable. And should able to set it.
Signed-off-by: kuanyu_chen <kuanyu_chen@edge-core.com>
The `-sv2` suffix was used to differentiate SNMP Dockers when we transitioned from "SONiCv1" to "SONiCv2", about four years ago. The old Docker materials were removed long ago; there is no need to keep this suffix. Removing it aligns the name with all the other Dockers.
Also edit Monit configuration to detect proper snmp-subagent command line in Buster, and make snmpd command line matching more robust.
- Add .gitignore files in each subdirectory of src/, so as to reduce the size of the .gitignore file in the project root, and also make it easier to maintain (i.e., if a directory in src/ is removed, there will not be outdated entries in the root .gitignore file.
- Also add missing .gitignore entries and remove outdated entries and duplicates.
The -sv2 suffix was used to differentiate SNMP Dockers when we transitioned from "SONiCv1" to "SONiCv2", about four years ago. The old Docker materials were removed long ago; there is no need to keep this suffix. Removing it aligns the name with all the other Dockers.
**- Why I did it**
For decoding system EEPROM of S6000 based on Dell offset format and S6000-ON’s system EEPROM in ONIE TLV format.
**- How I did it**
- Differentiate between S6000 and S6000-ON using the product name available in ‘dmi’ ( “/sys/class/dmi/id/product_name” )
- For decoding S6000 system EEPROM in Dell offset format and updating the redis DB with the EEPROM contents, added a new class ‘EepromS6000’ in eeprom.py,
- Renamed certain methods in both Eeprom, EepromS6000 classes to accommodate the plugin-specific methods.
**- How to verify it**
- Use 'decode-syseeprom' command to list the system EEPROM details.
- Wrote a python script to load chassis class and call the appropriate methods.
UT Logs: [S6000_eeprom_logs.txt](https://github.com/Azure/sonic-buildimage/files/4735515/S6000_eeprom_logs.txt), [S6000-ON_eeprom_logs.txt](https://github.com/Azure/sonic-buildimage/files/4735461/S6000-ON_eeprom_logs.txt)
Test script: [eeprom_test_py.txt](https://github.com/Azure/sonic-buildimage/files/4735509/eeprom_test_py.txt)
- Sensor and Fan information added to primary platforms for thermal API.
- Refactors involving better abstractions, code reuse and dead code removal.
- Improvements to the diag capabilities
- Pylintrc added to improve code quality. Will become fatal at a later time.
Co-authored-by: Baptiste Covolato <baptiste@arista.com>
Cleanup description string
First port (management port) are excluded from general port naming scheme.
Management port are excluded from general port naming scheme.
before:
|on GNS3 |in SONiC |
|---------|---------|
|Ethernet0|eth0 |
|Ethernet1|Ethernet0|
|Ethernet2|Ethernet4|
|Ethernet3|Ethernet8|
after:
|on GNS3 |in SONiC |
|---------|---------|
|eth0 |eth0 |
|Ethernet0|Ethernet0|
|Ethernet1|Ethernet4|
|Ethernet2|Ethernet8|
Signed-off-by: Masaru OKI <masaru.oki@gmail.com>
* Update sonic-sairedis (sairedis with SAI 1.6 headers)
* Update SAIBCM to 3.7.4.2, which is built upon SAI1.6 headers
* missed updating BRCM_SAI variable, fixed it
* Update SAIBCM to 3.7.4.2, updated link to libsaibcm
* [Mellanox] Update SAI (release:v1.16.3; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* Update sonic-sairedis pointer to include SAI1.6 headers
* [Mellanox] Update SDK to 4.4.0914 and FW to xx.2007.1112 to match SAI 1.16.3 (API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* ensure the veth link is up in docker VS container
* ensure the veth link is up in docker VS container
* [Mellanox] Update SAI (release:v1.16.3.2; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* use 'config interface startup' instead of using ifconfig command, also undid the previous change'
Co-authored-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
- Skip thermalctld in DellEMC S6000, S6100, Z9100 and Z9264 platforms.
- Change the return type of thermal Platform APIs in DellEMC S6000, S6100, Z9100 and Z9264 platforms to 'float'.
* [platform]: Add a new supported platform, Delta-agc032
Switch Vendor: Delta
Switch SKU: Delta-agc032
CPU: BROADWELL-DE
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk3, BCM56980
Port Configuration: 32x400G + 2x10G
- What I did
Add a new Delta platform Delta-agc032.
- How I did it
Add files by following SONiC Porting Guide.
- How to verify it
1. decode-syseeprom
2. sensors
3. psuutil
4. sfputil
5. show interface status
6. bcmcmd
Signed-off-by: zoe-kuan <ZOE.KUAN@deltaww.com>
3y Power YPEB-1200am PSU doens't support read fan_dir from pmbus register
Check with vendor this PUS type only support F2B fan direction. So add to show "F2B"
when red psu_fan_dir sysfs.
* Trigger thermal action log only if thermal condition changes
* test file existence before read file content
* fix error for set psu fan speed
* Remove logs because it print too frequently
- bug fix : Fixed an issue which the nps ko file was not loaded due to the wrong service file name
- Optimize the code to reduce changes due to the kernel upgrade
- Remove nephos ko file loaded in swss.service.j2 because it has loaded at syncd.service.j2
For detecting transceiver change events through xcvrd in DellEMC S6000, S6100 and Z9100 platforms.
- In S6000, rename 'get_transceiver_change_event' in chassis.py to 'get_change_event' and return appropriate values.
- In S6100, implement 'get_change_event' through polling method (poll interval = 1 second) in chassis.py (Transceiver insertion/removal does not generate interrupts due to a CPLD bug)
- In Z9100, implement 'get_change_event' through interrupt method using select.epoll().
This patchset implement the following:
- Setting the FAN frequency
- Corrections to the EM policy with respect to platform
defined temperature / fan values
- Updates to the platform monitorng script logging
- Fixes to platform initialization script
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
Update SAI/SDK/FW and MSN4700 device files to support 8 lanes 400G
Update SAI to 1.16.3
Update SDK to 4.4.0914
Update FW to *.2007.1112
Update MSN4700 device files to support 8 lanes 400G
currently, vs docker always create 32 front panel ports.
when vs docker starts, it first detects the peer links
in the namespace and then setup equal number of front panel
interfaces as the peer links.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
- Add Makefile rules to build debug containers for SWI images
- Fix some platform API implementation for xcvrd and thermalctld
- Improvements to arista diag command
- Miscellaneous refactors
Co-authored-by: Maxime Lorrillere <mlorrillere@arista.com>
* New SKU support for MSN3420
Signed-off-by: Shlomi Bitton <shlomibi@mellanox.com>
Conflicts:
device/mellanox/x86_64-mlnx_msn2700-r0/plugins/sfputil.py
* Add CPLD's
* Symlink fixes and semantics
* Adding new platform at end of lines
This patch set implements the following:
- Fixes the conflicts in chassis.py / platform.py in sonic_platfrom
- Consolidating the common library files in sonic_platform
- Moving QFX5210 specific drivers to qfx5210/modules
- Moving Juniper common fpga drivers to common/modules
- Cleaning up the platform driver files
- Bug fixes in QFX5210 platform monitor & initialiazation script
- Fixing the bugs in QFX5210 eeprom parsing
Signed-off-by: Ciju Rajan K <crajank@juniper.net>