Images built from master branch and installed on devices where we mount /var/lib/docker in RAM (because the HDD is small) were failing to boot properly. The Docker service failed to start because /var/lib/docker was filled to 100%. This is due to the increase in total number of containers in the image.
As of today, /var/lib/docker contains 1.3 GB of data. Therefore, this PR increases the size of the ramdisk to 1.5 GB to accommodate all the containers. Example output below from an Arista-7050-QX32 SKU:
```
admin@sonic:~$ df -h
Filesystem Size Used Avail Use% Mounted on
...
tmpfs 1.5G 1.3G 172M 89% /var/lib/docker
...
```
Changes:
-- Removing the part where build dependencies are installed in setup.py.
-- Adding build dependencies in corresponsing rules\..*.mk file.
Signed-off-by: Praveen Chaudhary pchaudhary@linkedin.com
- Skip thermalctld in DellEMC S6000, S6100, Z9100 and Z9264 platforms.
- Change the return type of thermal Platform APIs in DellEMC S6000, S6100, Z9100 and Z9264 platforms to 'float'.
* [platform]: Add a new supported platform, Delta-agc032
Switch Vendor: Delta
Switch SKU: Delta-agc032
CPU: BROADWELL-DE
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk3, BCM56980
Port Configuration: 32x400G + 2x10G
- What I did
Add a new Delta platform Delta-agc032.
- How I did it
Add files by following SONiC Porting Guide.
- How to verify it
1. decode-syseeprom
2. sensors
3. psuutil
4. sfputil
5. show interface status
6. bcmcmd
Signed-off-by: zoe-kuan <ZOE.KUAN@deltaww.com>
**- Why I did it**
Advance sonic-py-swsssdk submodule to fix#4632
**- How I did it**
In py3, the response from redis connector is encoded as byte array. They
need to be decoded before accessing them as strings.
Use following commands to test
sonic-db-cli CONFIG_DB "keys *"
sonic-db-cli CONFIG_DB "hget PORT|Ethernet0 admin_status"
**- How to verify it**
sonic-db-cli CONFIG_DB "keys *"
sonic-db-cli CONFIG_DB "hget PORT|Ethernet0 admin_status"
Signed-off-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com>
3y Power YPEB-1200am PSU doens't support read fan_dir from pmbus register
Check with vendor this PUS type only support F2B fan direction. So add to show "F2B"
when red psu_fan_dir sysfs.
* Trigger thermal action log only if thermal condition changes
* test file existence before read file content
* fix error for set psu fan speed
* Remove logs because it print too frequently
1. On the ARM architecture, python-j2cli is installed from source code, depends on python-setuptools and python-wheel.
2. On the ARM architecture, install python-cryptography from source code(from azure-storage==0.36.0) depends on libffi-dev and libssl-dev.
3. install crossbuild in buster slave for arm arch kernel compile.
4. Versions before 18.09 do not install docker-ce-cli.
5. umount /proc after dockerfs.
6. change image apt source list from stretch to buster for arm.
Added support for S6000 new HWSKU-Q20S48
Modified port_config.ini, TD2 settings to bring the ports UP.
Added support for S6000 new HWSKU-Q20S48(20x40G-48x10G)
This HWSKU is applicable for S6000 platform, not S6000-ON platform
