LED_PROC_INIT_SOC variable was incorrectly referenced as LED_SOC_INIT_SOC. Introduced in #5483
Rather than fixing the typo, I decided to simplify the script, removing the need for the conditional altogether by moving the bcmcmd call inside the conditional which checks for the presence of LED_SOC_INIT_SOC.
#### Why I did it
Microsoft reported occasional daemon crashes on devices running 201911. On close inspection it was due to PMBus reads failing on IOError on very rare occasions.
#### How I did it
Add try/except block on performing reads on PMBus GPIOs.
Co-authored-by: Zhi Yuan (Carl) Zhao <zyzhao@arista.com>
Why I did it
To recover the SSD upgrade state in case, if ONIE-uninstall or ssd_fw_upgrade folder got deleted.
To handle newer SSD version(S21506G - 3IE GPIO7 low devices).
Also correcting the error messages for non-upgraded S6100s.
- Why I did it
Updated FW to xx.2008.2526 version.
Fixed issues:
1. Spectrum-2, Spectrum-3 | sFlow | High CPU load and high on fully loaded switch.
2. Spectrum-2, Spectrum-3 | Fine grain LAG | in rare cases doesn’t update the right entry
- How I did it
Updated submodule pointer and version in a Makefile.
- How to verify it
Full regression and bugs validation
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
Why I did it
Added soft-reboot plugin support.
Added SSD version s16425cq check
Added error message to display in console/SSH in case reboot is called in faulty/non-upgraded devices.
New features and fixes in the new SDK/FW:
SN4600C | AN/LT support
SN2700 | AN/LT bugs fixes
WJH | FID_MISS support
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Fix the following issues:
Spectrum-2, Spectrum-3 | Port | Fix link issue when using 25 GbE rate between two ports while one is on Spectrum-2-based system and the other is on Spectrum-3-based system
All | warmboot | fail to upgrade from earlier SONiC versions with official SDK/FW 4.4.2306 (was on SONiC 201911)
All | What-Just-Happened | When enabling or disabling WJH under high traffic load to the host CPU, in very specific and low probability conditions, an error could occur, that may result in loss of data, channel failure or in extreme cases SW failure
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
The S6000 devices, the cold reboot is abrupt and it is likely to cause issues which will cause the device to land into EFI shell. Hence the platform reboot will happen after graceful unmount of all the filesystems as in S6100.
Bug fixes
-Removing critical thermal zones to prevent unexpected software system shutdown:
Kernel 4.9 -0071-mlxsw-core-Remove-critical-trip-point-from-thermal-z.patch
Kernel 4.19 -076-mlxsw-core-Remove-critical-trip-point-from-thermal-z.patch
- hw-mgmt: thermal: Add hardcoded critical trip point
- Removing redundant link for cpld3 for fixed systems (SN2100, SN2010).
- Fix an issue with a missed attribute for cpld3 (port CPLD) for SN2700, SN2410.
Signed-off-by: Stephen Sun <stephens@nvidia.com>
- Why I did it
To pick up new features and fix from SDK/FW and SAI
SDK/FW new Feature:
All | Added support for multiple modules and cable types. For full list contact Nvidia networking support
Spectrum-3 | SN46000C | Added support for up to 5W on ports 49 to 64 .
SDK/FW bugs' fix:
All | fast reboot | fast boot failure from latest 201811 to 201911 and above
Spectrum | 10GbE/1GbE Transceiver (FTLX8574D3BCV) stopped working after firmware upgrade
Spectrum-2 | When device is rebooted with locked Optical Transceivers in split mode, the firmware may get stuck
Spectrum-2 | SN3700 | When connecting at 200GbE to Ixia K400, Ixia receives CRC errors
Spectrum-2 | SN3800 | On rare occasions packets loss may be experienced due to signal integrity issues
Spectrum-2 | When the port is a member of a LAG, after a warmboot and port toggle on the peer-side, the port remains down
Spectrum-3 | SN4700 | While using Optic cable in Split 4x1 mode in PAM4, when two first ports are toggled, the other 2 ports go down
Spectrum-3 | SN4700 | When working in 400GbE, deleting the headroom configuration (changing buffer size to zero) on the fly may cause continual packet drops
SAI
All | Counters | Update tunnel decap counter to capture VNI miss
- How I did it
Update the related version number in the make files and update the submodule pointer accordingly.
- How to verify it
Run regression test and everything works good.
Why I did it
To monitor the SSD health condition in DellEMC S6100 platform post upgrade.
A daemon is introduced to monitor the SSD every one hour.
To check for SSD status at boot time and at the time of cold-reboot.
All these changes are supported only for newer SSD firmware.
Added a platform_reboot_pre_check script to prevent cold-reboot based on SSD status.
Depends on Azure/sonic-utilities#1472
DO NOT MERGE UNTIL ABOVE PR IS MERGED
This is to address the issue when "mmuconfig -p egress_lossy_profile" is executed which causes SYNCd failure with SAI_STATUS_INSUFFICIENT_RESOURCE for attr SAI_BUFFER_PROFILE_ATTR_RESERVED_BUFFER_SIZE.
This change also requires the change from (https://github.com/Azure/sonic-swss/pull/1649)
This SAI change was already tested as part of the (https://github.com/Azure/sonic-swss/pull/1649) PR.
In rare case can see that xcvrd failed due to "UnboundLocalError: local variable 'label_port' referenced before assignment"
Init "label_port" as None at the beginning of the function, to avoid the case that "label_port" not assigned.
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
**- Why I did it**
- The thermalctld daemon on the Pmon docker requires support from the thermal manager API.
**- How I did it**
- Removed the old function for detecting a faulty fan.
- Removed the old function for detecting excess temperature.
- Implement thermal_manager APIs based on ThermalManagerBase
- Implement thermal_conditions APIs based on ThermalPolicyConditionBase
- Implement thermal_actions APIs based on ThermalPolicyActionBase
- Implement thermal_info APIs based on ThermalPolicyInfoBase
- Add thermal_policy.json
Bring in a fix for thermal shutdown observed while executing warm-reboot:
- All | prevent FW access during ISSU
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
To have the following fixes:
* All | Port status remains down after warm boot and flapping the port on peer side
* All | LAG HASH | IPv6 SRC_IP is not accounted in LAG hashing [
* All | ASIC driver | Kernel crash observed when driver reload is initiated before it fully loaded
* Spectrum-3 | Buffer | In lossless configuration, headroom is been evicted only when the shared buffers is free
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
On the DCS-7060CX-32S, a SEU can happen on a CPLD which by default would reboot the platform.
Other SEU scenarios are already handled but this one was missed since it's specific to this platform.
It's a pretty rare case which will now be reported in the syslog the same way others are.
Include SAI bug fixes:
Apply device MAC on port host interface when port is removed from LAG.
[Shared Headroom]: fixed watermark handling for SHP flow
Decrease verbosity of policer unbind message when no policer is attached
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
** Why I did it **
Disable SDK extended dump due to issue found
** How I did it **
Update SAI submodule
** How to verify it **
Verify the SDK extended dump is not called.
Signed-off-by: Eran Dahan <erand@nvidia.com>
when parallel build is enabled, both docker-fpm-frr and docker-syncd-brcm
is built at the same time, docker-fpm-frr requires swss which requires to
install libsaivs-dev. docker-syncd-brcm requires syncd package which requires
to install libsaibcm-dev.
since libsaivs-dev and libsaibcm-dev install the sai header in the same
location, these two packages cannot be installed at the same time. Therefore,
we need to serialize the build between these two packages. Simply uninstall
the conflict package is not enough to solve this issue. The correct solution
is to have one package wait for another package to be uninstalled.
For example, if syncd is built first, then it will install libsaibcm-dev.
Meanwhile, if the swss build job starts and tries to install libsaivs-dev,
it will first try to query if libsaibcm-dev is installed or not. if it is
installed, then it will wait until libsaibcm-dev is uninstalled. After syncd
job is finished, it will uninstall libsaibcm-dev and swss build job will be
unblocked.
To solve this issue, _UNINSTALLS is introduced to uninstall a package that
is no longer needed and to allow blocked job to continue.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
backport c4b5b002c3
make swss build depends only on libsairedis instead of syncd. This allows to build swss without depending
on vendor sai library.
Currently, libsairedis build also buils syncd which requires vendor SAI lib. This makes difficult to build
swss docker in buster while still keeping syncd docker in stretch, as swss requires libsairedis which also
build syncd and requires vendor to provide SAI for buster. As swss docker does not really contain syncd
binary, so it is not necessary to build syncd for swss docker.
[submodule]: update sonic-sairedis
1e42517996bfe41ac58d4c25ee3f93502befcb9d (HEAD -> 201911) [build]: add option to build without syncd
Signed-off-by: Guohan Lu <lguohan@gmail.com>
**- Why I did it**
There is a preference to use thermalctld instead of fancontrol for 201911 release branch. The Arista platform submodule updates and thermal policies in the platforms will allow Arista devices to use thermalctld instead of fancontrol.
**- How I did it**
I cherry-picked the necessary commits from master branch for sonic-platform-modules-arista into 201911 branch. I've also added the file to skip fancontrol and added the thermal policies json.
**- How to verify it**
On Gardena, Upperlake, Clearlake, and Lodoga thermalctld is up and running with no errors. Fans show ~29%.
Co-authored-by: Zhi Yuan Carl Zhao <zyzhao@arista.com>
In order to prevent "mlxsw_minimal" driver accessing ASIC during in
service firmware upgrade flow, SDK will raise "OFFLINE" 'udev' event
at early beginning of such flow. When this event is received,
hw-managemnet will remove "mlxsw_minimal" driver.
There is no need to implement opposite "ONLINE" event, since this flow
is ended up with "kexec".
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Bugs fixes:
All | Kernel | During system reload when CPU is loaded with heavy traffic, a Kernel Panic may occur.
All | Modules, Port split | FW stuck when device rebooted with locked Optical Transceivers in split mode
Spectrum-3 | PFC | On Spectrum-3 systems, slow reaction time to Rx pause packets on 40GbE ports may lead to buffer overflow on servers.
Spectrum-3 | SN4700, Port Split | On rare occasion SN4700, conducting 100G split (4x25G) in NRZ when splitter port 1 or 2 are down, ports 3 and 4 will also go down.
Enahncments:
All | Kernel | new notification on ISSU start, so other kernel drivers can disable any interface to ASIC
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- Why I did it
Fix setting PSU led to 'green' or 'red' states.
Fix return False if unsupported color request.
Remove 'off' option for PSU led API since it is not supported in Mellanox.
- How I did it
Fix import missing information.
Return 'False' when unsupported led color is requested, preventing an exception.
- How to verify it
Try to set PSU LED to different status with Mellanox platform device.
Try to set PSU LED color to unsupported color with Mellanox platform device.
This PR limited the number of calls to sonic-cfggen to one call
per iteration instead of current 3 calls per iteration.
The PR also installs jq on host for future scripts if needed.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
EEPROM cache file is not refreshed after install a new ONIE version even if the eeprom data is updated. The current Eeprom class always try to read from the cache file when the file exists. The PR is aimed to fix it.
