* Build docker-gbsyncd-broncos image
* Correct typo in LIBSAI_BRONCOS_URL_PREFIX
* Update docker-gbsyncd-broncos/Dockerfile.j2
* Enable debug shell support on docker-gbsyncd-broncos
* Include bcmsh in docker-gbsyncd-broncos
Why I did it
In docker-gbsyncd-broncos image, enable debug shell support for BRCM broncos PHY.
How I did it
How to verify it
Note: need enable attr SAI_SWITCH_ATTR_SWITCH_SHELL_ENABLE support in BCM PAI library
# bcmsh
Press Enter to show prompt.
Press Ctrl+C to exit.
NOTICE: Only one bcmsh or bcmcmd can connect to the shell at same time.
BRCM:> help
help
List of available commands
- h or help => Print command menu
- l => Print list of active ports on the PHY
- ps <port_id> <options> => Print port status
<options> => 1 -> Link status
=> 2 -> Link training failure status
=> 3 -> Link training RX status
=> 4 -> PRBS lock status
=> 5 -> PRBS lock loss status
- rd <port_id> <addr> <no of registers to read> => Read register contents
- wr <port_id> <addr> <data> => Write register data
- rrd <lanemap> <if_side> <addr> <no of registers to read> => Raw read register contents using lanemap and if_side (line = 0, system = 1)
- rwr <lanemap> <if_side> <addr> <data> => Raw write register data using lanemap and if_side (line = 0, system = 1)
- fw or firmware => Print firmware version of the PHY
- pd or port_dump <port_id> <flags> => Dump port status
- eyescan <port_id> => Display eye scan
- fec_status <port_id> => Get fec status of the port
- polarity <lanemap> <if_side> <TX polarity> <RX Polarity> => Set TX and RX polarity
<lanemap> => 0xF, 0xFF, or 0xFFFF based on number of lanes
<if_side > => Line = 0, System = 1
<TX/RX Polarity> =>_TX/RX Polarity bitmap of all lanes
Each bit represents a lane number.
E.g. Lane 0's polarity value (0 or 1) is populated in Bit 0.
- polarity <lanemap> <if_side> => Print TX and RX polarity
- lb <port_id> <lb_value> => Enable loopback on the port
lb_value = 0 -> Disable, 1 -> PHY, 2 -> MAC
- lb <port_id> => Print loopback configuration of the port
- prbs <port_id> <options> <val> => Set/Get PRBS configuration
<options> => 1 -> Get PRBS state and polynomial
2 -> Set PRBS Polynomial, <val> - PRBS Polynomial
Please refer to phy/chip documentation for valid values
3 -> Enable PRBS
<val> => 0 Disable PRBS
1 Enable both PRBS Transmitter and Receiver
2 Enable PRBS Receiver
3 Enable PRBS Transmitter
exit or q => Exit the diagnostic shell
bgpd.main.conf.j2: bugfix-9739
* Update bgpd.main.conf.j2 to gracefully handle the bgp configuration cases for when 'bgp_asn' is set to 'None', 'Null', or missing.
How I did it
Include a conditional statement to avoid configuring bgp in FRR when 'bgp_asn' is missing or set to 'None' or 'Null'
How to verify it
Configure 'bgp_asn' as 'None', 'Null' or have it missing from configurations and verify that /etc/frr/bgpd.conf does not have invalid bgp configurations like 'router bgp None'
Description for the changelog
Update bgpd.main.conf.j2 to gracefully handle the bgp configuration cases for when 'bgp_asn' is set to 'None', 'Null', or missing for bugfix 9739.
Signed-off-by: cchoate54@gmail.com
Why I did it
Unify the Debian mirror sources
Make easy to upgrade to the next Debian release, not source url code change required.
Support to customize the Debian mirror sources during the build
Relative issue: #12523
sonic-host-services submodule update with following changes
6eac2d3 Merge pull request #19 from judyjoseph/macsec_feature_enable
31c6108 Sync has_per_asic_scope attribute to config_db in all namespaces for multi-asic
185547f Add UT to improve coverage, for namespace config update
7c3aca0 macsec_supported info is part of DEVICE_RUNTIME_METADATA itself.
- Why I did it
Fix logrotate firstaction script to reflect correct size. The size was modified to change dynamically based on disk size. However this variable was not updated
#9504
- How I did it
Updated the variable based on disk size
- How to verify it
Verify in the generated rsyslog file if the variable is correctly generated from jinja template
- Why I did it
Update SN2201 dynamic minimum fan speed table according to data provided by the thermal team.
- How I did it
Update the thermal table in device_data.py
- How to verify it
Run platform related regression
Signed-off-by: Kebo Liu <kebol@nvidia.com>
686b9b1 Update Makefile to provision the ability of building with non-upstream patches (#296)
3b95205 [patch]: Introduce sysctl param `arp_evict_no_carrier` (#293)
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
Why I did it
Fixes#12614
How I did it
In the container_checker the database_chassis is added to expected container if device is supervisor
To detect the device is superviso, add supervisor=1 to the platform_env.conf of 7808 sup platform
How to verify it
run container_checker monit check
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess.Popen()` and `subprocess.run()` is used with `shell=True`, which is very dangerous for shell injection.
`os` - not secure against maliciously constructed input and dangerous if used to evaluate dynamic content
#### How I did it
Replace `os` by `subprocess`
Remove unused functions
Why I did it
In case the device contains more then one FAN drawer, the FANs name was incorrect.
How I did it
Passed max fan value to FAN object.
Fixed get_name() FAN API
How to verify it
show platform fan
Add dualtor test using TestbedV2 in buildimage repo.
Why I did it
Add dualtor test using TestbedV2 in buildimage repo.
How I did it
Add dualtor test using TestbedV2 in buildimage repo.
Signed-off-by: Yutong Zhang <yutongzhang@microsoft.com>
Why I did it
[Build] Fix the docker-sync not found issue
How I did it
When SONIC_CONFIG_USE_NATIVE_DOCKERD_FOR_BUILD not enabled, not to remove the docker-sync tag.
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess` is used with `shell=True`, which is very dangerous for shell injection.
`os` - not secure against maliciously constructed input and dangerous if used to evaluate dynamic content
#### How I did it
remove `shell=True`, use `shell=False`
Replace `os` by `subprocess`
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess` is used with `shell=True`, which is very dangerous for shell injection.
#### How I did it
remove `shell=True`, use `shell=False`
#### How to verify it
Manual test
Pass UT
Why I did it
SONiC will report the kernel dump while system reboot in Belgite platform as the following shows:
How I did it
Cause:
Invalid cdev container pointer from the inode is being accessing in misc
device open, which causes a memory corruption in the slub.
Because of the slub corruption, random crash is seen during reboot.
Fix: - Instead of cdev pointer from the inode, mdev container pointer is
used from the file->privdate_data member.
Action: update the pddf_custom_wdt driver,
How to verify it
Do the reboot stress test to check whether there is kernel dump during reboot progress
#### Why I did it
Submodule update for sonic-swss-common with following change:
```
276f47c [sonic-db-cli] Fix sonic-db-cli crash when database config file not ready issue. (#639)
```
#### How I did it
#### How to verify it
#### Which release branch to backport (provide reason below if selected)
<!--
- Note we only backport fixes to a release branch, *not* features!
- Please also provide a reason for the backporting below.
- e.g.
- [x] 202006
-->
- [ ] 201811
- [ ] 201911
- [ ] 202006
- [ ] 202012
- [ ] 202106
#### Description for the changelog
Submodule update for sonic-swss-common with following change:
276f47c [sonic-db-cli] Fix sonic-db-cli crash when database config file not ready issue. (#639)
#### A picture of a cute animal (not mandatory but encouraged)
Export remote address to environment variable for TACACS authorization.
#### Why I did it
When remote user login, nss-tacplus need user remove address for TACACSS authorization.
#### How I did it
Export remote address to environment variable "SSH_REMOTE_IP"
#### How to verify it
Pass all E2E test.
#### Which release branch to backport (provide reason below if selected)
<!--
- Note we only backport fixes to a release branch, *not* features!
- Please also provide a reason for the backporting below.
- e.g.
- [x] 202006
-->
- [ ] 201811
- [ ] 201911
- [ ] 202006
- [ ] 202012
- [ ] 202106
- [ ] 202111
- [ ] 202205
#### Description for the changelog
Export remote address to environment variable for TACACS authorization.
#### Ensure to add label/tag for the feature raised. example - PR#2174 under sonic-utilities repo. where, Generic Config and Update feature has been labelled as GCU.
#### Link to config_db schema for YANG module changes
<!--
Provide a link to config_db schema for the table for which YANG model
is defined
Link should point to correct section on https://github.com/Azure/sonic-buildimage/blob/master/src/sonic-yang-models/doc/Configuration.md
-->
#### A picture of a cute animal (not mandatory but encouraged)
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess` is used with `shell=True`, which is very dangerous for shell injection.
#### How I did it
remove `shell=True`, use `shell=False`
#### How to verify it
Pass UT
Manual test
* Fix kube mode to local mode long duration issue
* Remove IPV6 parameters which is not necessary
* Fix read node labels bug
* Tag the running image to latest if it's stable
* Disable image_version_higher check
* Change image_version_higher checker test case
Signed-off-by: Yun Li <yunli1@microsoft.com>
Why I did it
This changes should go with updated SDE for BFN. Without update we do see orchagent core dump.
How I did it
Revert changes
How to verify it
Deploy topology. No core dump appears
Send remote address in TACACS+ authorization message.
#### Why I did it
TACACS+ authorization message not send remote address to server side.
#### How I did it
Send remote address in TACACS+ authorization message.
#### How to verify it
Pass all E2E test.
Create new test case to validate remote address been send to server side.
#### Which release branch to backport (provide reason below if selected)
<!--
- Note we only backport fixes to a release branch, *not* features!
- Please also provide a reason for the backporting below.
- e.g.
- [x] 202006
-->
- [ ] 201811
- [ ] 201911
- [ ] 202006
- [ ] 202012
- [ ] 202106
- [ ] 202111
- [ ] 202205
#### Description for the changelog
Send remote address in TACACS+ authorization message.
#### Ensure to add label/tag for the feature raised. example - [PR#2174](https://github.com/sonic-net/sonic-utilities/pull/2174) where, Generic Config and Update feature has been labelled as GCU.
#### Link to config_db schema for YANG module changes
<!--
Provide a link to config_db schema for the table for which YANG model
is defined
Link should point to correct section on https://github.com/Azure/sonic-buildimage/blob/master/src/sonic-yang-models/doc/Configuration.md
-->
#### A picture of a cute animal (not mandatory but encouraged)
Changes:
-- Change name-space from Azure to sonic-net.
-- Sort yang list in setup.py for yang-models list.
#### Why I did it
Sonic repo has moved to Linux-foundation.
#### How I did it
[yang-models]: Change name-space from Azure to sonic-net.
#### How to verify it
PR Tests are good enough to verify.
#### Why I did it
Currently at the Azure build system, the P4RT container is disabled by default at the build time. Here the goal is to include the P4RT container at the build time while disabling it at the runtime. The user can enable/disable the p4rt app through the config based on the preference.
#### How I did it
Changed the config in rules/config and init-cfg.json.j2
* [openssh]: Restore behavior of ClientAliveCountMax=0
OpenSSH 8.2 changed the behavior of ClientAliveCountMax=0 such that
setting it to 0 disables connection-killing entirely when the connection
is idle. Revert that change.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
* Remove build-dep command that should not be there
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess.Popen()` and `subprocess.run()` is used with `shell=True`, which is very dangerous for shell injection.
`os` - not secure against maliciously constructed input and dangerous if used to evaluate dynamic content
#### How I did it
Replace `os` by `subprocess`, remove `shell=True`
#### How to verify it
Passed UT
Tested in DUT
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess` is used with `shell=True`, which is very dangerous for shell injection.
#### How I did it
remove `shell=True`, use `shell=False`
#### How to verify it
Pass UT
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess` is used with `shell=True`, which is very dangerous for shell injection.
`os` - not secure against maliciously constructed input and dangerous if used to evaluate dynamic content
`yaml.load` can create arbitrary Python objects
#### How I did it
Replace `os` by `subprocess`, remove `shell=True`
Use `yaml.safe_load()`
#### How to verify it
Pass UT
- Why I did it
Add the ability to the user to save the loglevel and make it persistent to reboot.
- How I did it
Move the logger tables from the LOGLEVEL DB to the CONFIG DB. Add new yang model to verify the new config schema.
- How to verify it
1. change the orchagent loglevel (for example) -> swssloglevel -c orchagent -l DEBUG
2. save the loglevel -> run config save
3. reboot
4. verify that the orchagent log level is still DEBUG ->run run redis-cli -n 4 hgetall "LOGGER|orchagent"
Update sonic-utilities submodule pointer to include the following:
4a3d49d Fix exception in adding mirror_session when gre_type is absent (#2458)
7e7d05c Update the DBmigrator to support persistent loglevel during warm-upgrade (#2370)
c2841b8 [doc]: Update Command-Reference.md (#2444)
254cafc Event Counters CLI (#2449)
2dab0d0 [techsupport] Adding FRR EVPN dumps (#2442)
3c0aece [show][muxcable] add support for show mux firmware version all (#2441)
Signed-off-by: dprital <drorp@nvidia.com>
Update sonic-swss-common submodule pointer to include the following:
* abda263 Make the loglevel persistent by moving the LOGGER table from the LOGLEVEL DB to the CONFIG DB ([#687](https://github.com/sonic-net/sonic-swss-common/pull/687))
Signed-off-by: dprital <drorp@nvidia.com>
d0fdf62 Check whether a pointer created by dynamic_cast is null before using it. (#689)
2cae742 [Fast/Warm restart] Implement helper class for waiting restart done (#691)
- Why I did it
Update SDK/FW version - 4.5.3186/2010_3186 in order to have the following changes:
New functionality:
1. Added support for 6.5W (Class 8) in ports 49-50, 53-54, 57-58, and 61-62 on SN4600 system
Fix the following issues:
1. On very rare occasion (~1/100K), during I2C transaction with MMS1V50-WM and MMS1V90-WR modules on SN4700 system, the module may send unexpected stop which violate the I2C specification, possibly affecting the link up flow
2. When running 1GbE speeds on SN4600 system, the port remained active while peer side was closed
3. While toggling the cable with ‘sfputil lpmode on/off’, error msg like “ERR pmon#xcvrd: Receive PMPE error event on module 1: status {X} error type {y}” could be received
4. When toggling many ports of the Spectrum devices while raising 10GbE link up and link maintenance is enabled, the switch may get stuck and may need to be rebooted
5. When trying to reconfigure the Flex Parser header and Flex transition parameters after ISSU, the switch will returned an error even if the configuration was identical to that done before performing the ISSU
6. While moving from lossless to lossy mode while shared headroom was used, reduction of the shared headroom can only be done prior to pool type change and when shared headroom is not utilized
7. SLL configuration is missing in SDK dump
8. If TTL_CMD_COPY is used in Encap direction for a packet with no TTL, then the value passed in the ttl data structure will be used if non-zero (default 255 if zero)
9. PCI calibration changes from a static to a dynamic mechanism
10. Layer 4 port information is not initialized for BFD packet event. To address the issue, remote peer UDP port information was added in BFD packet event
11. SDK returned error when FEC mode is set on twisted pair, when FEC was set to None
- How I did it
Update pointer for the SDK/FW
- How to verify it
Run regression tests
Signed-off-by: dprital <drorp@nvidia.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan arlakshm@microsoft.com
Why I did it
closes#12343
Today in SONiC the notify-keyspace-events is from DbInterface class when application try do any configdb set.
In Chassis the chassis_db may not get any configdb set operations, so there is chance this configuration will never be set.
So the chassis_db updates from one line card will not be propogated to other linecards, which are doing a psubscribe to get these event.
How I did it
update the redis.conf to set notify-keyspace-events AKE so that the notify-keyspace-events are set when the redis instance is started
How to verify it
Test on chassis
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`subprocess` is used with `shell=True`, which is very dangerous for shell injection.
#### How I did it
remove `shell=True`, use `shell=False`
