any event happening on ACL Rule Table (eg DATAACL rules
programmed) caused control plane default action to be triggered.
Now Control Plance ACTION will be trigger only
a) ACL Rule beloging to Control ACL Table
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
During platform deinitialization, dell_ich is not removed properly and when we do initialize s6100 platform, ICH driver sysfs attributes are not attached. Because of this, get_transceiver_change_event returns error and this leads xcvrd to crash.
This is to fix pcie firmware check assert in Broadcom SDK once the SAI changes merges. This will be in the future but adding the soc property in the broadcom config now.
Co-authored-by: Zhi Yuan Carl Zhao <zyzhao@arista.com>
Make Python3-swsscommon available in image.
```
admin@str-s6000-acs-13:~$ sudo apt-cache search swss
libswsscommon - This package contains Switch State Service common library.
python-swsscommon - This package contains Switch State Service common Python2 library.
python3-swsscommon- This package contains Switch State Service common Python3 library.
admin@str-s6000-acs-13:~$
```
- [acl-loader] Revert fix for IP protocol == 0 (#1142)
- Show sflow interface to display all interfaces enabled for sflow (#1143)
- [sflow_test.py]: tests for config sflow commands. (#1112)
- [config/console] Support add/del console port setting commands (#1136)
- [cli][bgp]use vtysh in the show ip bgp summary command (#1137)
- [README.md] Describe new package creation schema (#1131)
- [consutil] Remove actual baud and refactor lib for future change (#1130)
Signed-off-by: Danny Allen <daall@microsoft.com>
* Install ndppd during image build, and copy config files to image
* Configure proxy settings based on config DB at container start
* Pipe ndppd output to logger inside container to log output in syslog
To address issue #5525
Explicitly control the grub installation requirement when it is needed.
We have scenario where configuration migration happened but grub
installation is not required.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
implements a new feature: "BGP Allow list."
This feature allows us to control which IP prefixes are going to be advertised via ebgp from the routes received from EBGP neighbors.
Some platforms don't leverage the brcm led coprocessor.
However ledinit will try to load a non existing file and exit with an
error code.
This change is a cosmetic fix mostly.
- How to verify it
Boot a platform without the configuration and verify in the syslog that the exit status of ledinit is 0
Boot a platform with the configuration and verify in the syslog that the exit status of ledinit is 0 and the leds are working.
Verified by adding a dumb led_proc_init.soc on an Arista platform which usually doesn't use it.
be51ebc533cbe92a885c584b4611ffc92d10ea36 Add IPv6 key item support to request parser (#1449)
76e22516bffe45d577ab9cce4f5d96687140fe75 When teamd feature state is disabled the Netdevice created by teamd were (#1450)
6aa97ce7982b78a26803908c0ce12302e51df793 Use .clear() after std::move() (#1444)
d5757db5d896aa2405f6cbf9f4c150f46b27aa4e Add libzmq to README dependencies (#1447)
c7b262ee61973a48943603810c8246a2471d1862 Add libzmq to Makefiles (#1443)
0b2e59ab6b909e5ea06013da03215f0d1af1e618 [drop counters] Clarify log messages for initial counter setup (#1445)
003cf24353c845ef708d192b7da8d571537671e1 [dvs] Refactor and add buffer pool wm test (#1446)
2f5d2d99dfae506333bddda9de2f289f92bb889b [acl] Remove Ethertype from L3V6 qualifiers (#1433)
f7b974f7fc6474a6493a7b6d0676e17caffa6165 Fix issue: bufferorch only pass the first attribute to sai when setting attribute (#1442)
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
* Fix generate_l2_config: don't override hostname because sonic-cfggen may not read from Redis. Fix test_l2switch_template test case to test preset l2 feature.
* Improve test script: compare json files with sort_keys
* Revert changes on sample_output
* Remove members field in VLAN section. Fix test assertTrue statement.
**- Why I did it**
BGP_MONITORS sessions don't have corresponding DEVICE_NEIGHBOR_METADATA CONFIG_DB entries in the minigraphs. Prevent bgpcfgd to wait on such entries for BGP_MONITORS sessions.
**- How I did it**
Set constructor argument to False that means - don't wait for device neighbors metadata info for BGP_MONITORS
**- How to verify it**
Build an image, write on your device, use a minigraph with BGP_MONITORS sessions. Check that sessions are populated in the config.
Avoiding recursive update of maps as it consumes stack frames. This
PR introduces iterative version of deep_update method.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Rendering templates show different orders when rendered using Python
2 vs Python 3. This PR prepare for Python 3 packaging by creating
new dir 'py2' for Python 2 rendered test cases.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Jinja2 templates rendered using Python 3 interpreter, are required
to conform with Python 3 new semantics.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Natural sorting of SONiC config gen output consumes lot of CPU cycles.
The sole use of natsorted was to make test comparison easier and so,
the natsorting logic is now relocated to the test suite. As a result
sonic-cfggen gained nearly 1 sec per call since we no longer import
natsorted module!
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
CONiC config gen requires jinja2<3.0.0 for stretch and byangbind
versions 0.60.0/0.80.1 for Python 2/3 respectively. byangbind
is installed in the build docker because when it installed it
pulls enum34 as dependent package which is not required for
Python 3 and it breaks the build.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
implements a new feature: "BGP Allow list."
This feature allows us to control which IP prefixes are going to be advertised via ebgp from the routes received from EBGP neighbors.
* [Multi-Asic] Forward SNMP requests destined to loopback IP, and coming in through the front panel interface
present in the network namespace, to SNMP agent running in the linux host.
* Updates based on comments
* Further updates in docker_image_ctl.j2 and caclmgrd
* Change the variable for net config file.
* Updated the comments in the code.
* No need to clean up the exising NAT rules if present, which could be created by some other process.
* Delete our rule first and add it back, to take care of caclmgrd restart.
Another benefit is that we delete only our rules, rather than earlier approach of "iptables -F" which cleans up all rules.
* Keeping the original logic to clean the NAT entries, to revist when NAT feature added in namespace.
* Missing updates to log_info call.
**- Why I did it**
There is error i2c mapping for port 11,12 and port 19, 20.
**- How I did it**
Fix to correct i2c mapping
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
**- Why I did it**
- Platform API implementation using sonic-cfggen to get platform name and SKU name, which will fail when the database is not available.
- Chassis name is not correctly assigned, it shall be assigned with EEPROM TLV "Product Name", instead of SKU name
- Chassis model is not implemented, it shall be assigned with EEPROM TLV "Part Number"
**- How I did it**
1. Chassis
> - Get platform name from /host/machine.conf
> - Remove get SKU name with sonic-cfggen
> - Get Chassis name and model from EEPROM TLV "Product Name" and "Part Number"
> - Add function to return model
2. EEPROM
> - Add function to return product name and part number
3. Platform
> - Init EEPROM on the host side, so also can get the Chassis name model from EEPROM on the host side.
* src/sonic-platform-common 7255d3a...111dcf7 (2):
> [EEPROM] Add new function part_number_str to TlvInfoDecoder (#121)
> Fix fp_port_index error to get correct index type (#111)
**- Why I did it**
As discussed, This PR covers the below points.
1. Give precedence to platform.json only if both platform.json and hwsku.json file exist. In case only platform.json exists, we don’t allow breakout for that HWSKU and fallback to port_config.ini.
**- How I did it**
check for `hwsku.json` file presence under get_path_to_port_config_file function.
Signed-off-by: Sangita Maity <sangitamaity0211@gmail.com>
