Why I did it
Update Broadcom SAI to version 6.0.0.13, SDK 6.5.24, saibcm-modules to 6.5.24.gpl
How I did it
Brcm SAI 6.0 EA with fixes for CS00012203367, CS00012219613, CS00012213974, CS00012218290, CS00012217169, CS00012211718, CS00012213944, CS00012215529, CS00012218100, CS00012214196, CS00012212681, CS00012205138, CS00012208537, CS00012185316, CS00012208524, CS00012203367, CS00012197364.
* Add intel_iommu=off to installer.conf
* This solve flooding DMAR err msg: "handling fault status reg 2"
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* remove customized at24 driver
* Use kernel 5.10.46 upstream at24 driver directly. The ADDR16 issue on
old driver has gone.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* pin I2C-0/I2C-1 bus order
* otherwise, sometimes I2C-0/I2C-1 will be assigned to the undesired one.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* fix i2c bus num for fan driver
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* backward compatible with R0A/R0B HW
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* fix workdir for seastone2
Signed-off-by: Viktor Ekmark <viktor@ekmark.se>
* seastone2: Add I2C SFP definition for SFP1
Signed-off-by: Christian Svensson <blue@cmd.nu>
* [device/cel_seastone_2] sfputil logic for SFP1
Earlier logic resulted in the name of SFP1 being SFP33 which is not
correct. The cannonical source is seastone2_fpga module and it calls it
SFP1, so ensure the logic does as well.
Signed-off-by: Christian Svensson <blue@cmd.nu>
* [device/cel_seastone_2] sysfs paths for SFP1
Various changes that plumbs the correct port presence and DOM decoding
for the SFP1 port.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Co-authored-by: Christian Svensson <blue@cmd.nu>
Enable pca954x idle_disconnect to avoid possible I2C device address conflict.
How I did it
Change pca954x device_attr idle_state to -2 (MUX_IDLE_DISCONNECT).
How to verify it
Cat pca954x device_attr idle_state and confirm the value is -2.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
Why I did it
Reboot cause is not working in S52xx platforms.
How I did it
Modified platform API's.
How to verify it
Check "show reboot-cause" to verify the reboot reason
Why I did it
To incorporate the below changes in DellEMC S6100, S6000 platforms.
S6100, S6000:
Implement 'get_revision' method for Chassis
Implement 'get_maximum_consumed_power' method for FanDrawer
Implement 'get_revision', 'get_maximum_supplied_power' methods for PSU
Implement 'get_error_description' method for SFP.
S6100:
Implement 'get_module_index' method for Chassis
Implement 'get_description', 'get_maximum_consumed_power', 'get_oper_status', 'get_slot' methods for Module
Update component names in platform.json
How I did it
Implement the platform API methods in the respective device files
How to verify it
Verified that the respective sonic-mgmt platform API test cases report success.
Update Nokia platform sonic-pmon submoduel to the latest with the following commits
c41c823 Fix transceiver module dynamic insertion/removal operations
21a1df6 Fixed pcied process FATAl issue
7fc1fd4 Fix midplane status nokia_cmd
a14ee1c Override get_module() api in chassis
8a457fc SON-326: Watchdog logger changes and file scrubbing
7250eb1 SON-410: Fix missing eeprom access routine
7a70c42 Allow only reboot of self card for OC API test
6ab5d96 Fixed the flake8 compliant issues
807de95 APIs to set thermal threshold to return false
9b38265 SON-382: platform-dump with common techsupport
3f83a67 Add model, base_mac, system_eeprom and serial number support in moduel.py
848d311 SFP: Add get_error_description and fix return status for set_lpmode
1fcb5de PSU check presence of psu instance for APIs
7c68da3 Fixed the eagle and hornet card description
0c01d07 Module support for reboot API
- Use SfpOptoeBase by default to leverage new `sonic_xcvr` refactor
- Add support for `Woodleaf` product
- Move `libsfp-eeprom.so` to a different `.deb` package
- Add new logrotate configuration for arista logs
- Improve logging mechanism for the drivers (IO loglevel, fix syslog duplicates)
- Initialize chassis cards in parallel
- Refactor of `get_change_event` to fix interrupts treated as presence change
Why I did it
To implement fan control using thermalctld in DellEMC S6000 platform
Requires: Azure/sonic-linux-kernel#241
How I did it
Add thermal policies in 'thermal_policy.json'
Implemented thermal_manager.py and the necessary modules to perform fan control via thermalctld
Removed fancontrol.sh
How to verify it
Verified that the fan speeds are set based on the fan and temperature status.
Logs: S6000_fan_control_test_logs.txt
Why I did it
Adding SSD as part of platform components list.
Introducing platform_fw_au_reboot_handle to use auto-update functionality in fwutil
How I did it
Changes to be committed:
(use "git restore --staged <file>..." to unstage)
modified: platform/broadcom/sonic-platform-modules-dell/debian/platform-modules-s6100.install
new file: platform/broadcom/sonic-platform-modules-dell/s6100/scripts/platform_fw_au_reboot_handle
modified: platform/broadcom/sonic-platform-modules-dell/s6100/sonic_platform/chassis.py
modified: platform/broadcom/sonic-platform-modules-dell/s6100/sonic_platform/component.py
How to verify it
By running fwutil command.
Warning: fwupdate_fwimage_dir: /var/platform/fwpackage/.
Chassis Module Component Firmware Version (Current/Available) Status
--------- -------- ----------- ------------------------------- ----------------------------- ------------------
S6100-ON BIOS S6100-BIOS-3.25.0.2-9-noRP2.bin 3.25.0.2-8 / 3.25.0.2-9 update is required
FPGA smf_firmware_upgrade.tar 2.4 / 2.4 up-to-date
CPLD cpld_firmware_upgrade.tar 4 / 4 up-to-date
SSD ssd_firmware_upgrade.tar S16425cG / S16425cG up-to-date
root@sonic:~#
Why I did it
To support iTCO watchdog using watchdog APIs.
How I did it
Implemented a new watchdog class WatchdogTCO for interfacing with iTCO watchdog.
Updated reboot cause determination logic.
How to verify it
Verified that the watchdog APIs' return values are as expected.
Logs: UT_logs.txt
For broadcom sai, we only need to upgrade the version, not necessary the token part in the url.
Co-authored-by: Ubuntu <xumia@xumia-vm1.jqzc3g5pdlluxln0vevsg3s20h.xx.internal.cloudapp.net>
- add `set_write_max` and `get_write_max` apis to Sfp API
- add `get_revision` platform API
- implement `is_midplane_reacheable` API
- add software fallback for setting Xcvr low power mode
- add `get_error_description` API
- add support for Woodleaf SKU
- various fixes/refactors/cleanups
Signed-off-by: pettershao-ragilenetworks pettershao@ragilenetworks.com
What I did it
Add new platform x86_64-ragile_ra-b6510-32c-r0 (Trident 3)
ASIC Vendor: Broadcom
Switch ASIC: Trident 3
Port Config: 32x100G
Add new platform x86_64-ragile_ra-b6920-4s-r0 (Tomahawk 3)
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk 3
Port Config: 128x100G
-How I did it
Provide device and platform related files.
-How to verify it
show platform fan
show platform ssdhealth
show platform psustatus
show platform summary
show platform syseeprom
show platform temperature
show interface status
Remove the "4.19..." specific code to add "-unsigned" suffix and just do so for any linux version.
For the syseeprom API part, have the Arista syseeprom class inherit from a class that can populate db.
Co-authored-by: Zhi Yuan (Carl) Zhao <zyzhao@arista.com>
Why I did it
To include capabilities fields in platform.json of DellEMC S6000, S6100, Z9332f platforms.
How I did it
Add the capabilities fields in each platform's respective platform.json.
How to verify it
Ran sonic-mgmt platform api test cases that use capabilities fields and verified that the results are as expected.
BRCM SAI missed implementing the SAI API "sai_query_stats_capability()" which is causing build issue.
The build issue is impacting PR(s) that need to use this API.
This PR is to stubbed BRCM SAI to add this SAI API and return not implemented so that it will fix build issue that it is causing.
No other functional changes were made.
ipmihelper files are repeated for few DellEMC platforms. Removed the
files in sonic_platform since as part of debian rules,ipmihelper will be
copied to necessary directory.
Also add out of tree pca9548 mux driver to use platform data to mapping i2c bus with front panel port.
Signed-off-by: Jakkapan Jangmuang <jjangmua@celestica.com>
Co-authored-by: Saikrishna Arcot <sarcot@microsoft.com>
Add an include in saibcm-modules and saibcm-modules-dnx that are now
needed due to Mellanox kernel patches.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
The kernel already provides psample, and with module versioning being
done in modpost, having the SDK compile its own copy of psample breaks
loading dependent modules.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Update the build rules in saibcm-modules to use the 5.10 kernel instead
of searching for the 4.19 kernel. In addition, some code changes were
done to get it to compile. The main categories of such changes are as
follows:
* For /proc files, `struct file_operations` has been replaced with
`struct proc_ops`.
* Y2038 changes to use the new APIs, since `do_gettimeofday()` is no
longer available.
* Minor changes in how external kernel module symbols are read by
modpost.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
- Why I did it
In case an app.ext requires a dependency syncd^1.0.0, the RPC version of syncd will not satisfy this constraint, since 1.0.0-rpc < 1.0.0. This is not correct to put 'rpc' as a prerelease identifier. Instead put 'rpc' as build metadata in the version: 1.0.0+rpc which satisfies the constraint ^1.0.0.
- How I did it
Changed the way how to version in RPC and DBG images are constructed.
- How to verify it
Install app.ext with syncd^1.0.0 dependency on a switch with RPC syncd docker.
Signed-off-by: Stepan Blyshchak <stepanb@nvidia.com>
Why I did it
Added Support for Dell EMC S5212f platform
How I did it
Implemented the support for Dell EMC S5212f platform
Platform: x86_64-dellemc_s5212f_c3538-r0
HwSKU: DellEMC-S5212f-P-25G
ASIC: broadcom
ASIC Count: 1
How to verify it
Verified the show command outputs
Why I did it
Added Support for Alphanetworks SNJ60D0-320F platform
How I did it
Implemented the support for Alphanetworks SNJ60D0-320F platform
Platform: x86_64-alphanetworks_snj60d0_320f-r0
HwSKU: Alphanetworks-SNJ60D0-320F
ASIC: broadcom
ASIC Count: 1
How to verify it
Verified the show command outputs
Why I did it
PCIe Gen1 settings was needed for Dell S6000 device.
How I did it
Modified from Gen2 to Gen 1 speed for Dell S6000 PCIe devices
How to verify it
Check lspci output, verify the syslogs
Why I did it
Added support for the device S5224F
How I did it
Implemented the support for the platform S5224F
Switch Vendor: DellEMC
Switch SKU: S5224F-ON
ASIC Vendor: Broadcom
SONiC Image: sonic-broadcom.bin
How to verify it
Verified the show platform/interface commands
Why I did it
Added support for the device N3248PXE
How I did it
Implemented the support for the platform N3248PXE
n3248pxe_unit_test_log.txt
Switch Vendor: DellEMC
* Switch SKU: N3248PXE
* ASIC Vendor: Broadcom
* SONiC Image: sonic-broadcom.bin
How to verify it
Verified the show platform commands
Why I did it
Added support for the device N3248TE
How I did it
Implemented the support for the platform N3248TE
Switch Vendor: DellEMC
Switch SKU: N3248TE
ASIC Vendor: Broadcom
SONiC Image: sonic-broadcom.bin
How to verify it
Verified the show platform commands
What I did it
Add new platform x86_64-ragile_ra-b6910-64c-r0 (Tomahawk 3)
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk 3
Port Config: 64x100G
-How I did it
Provide device and platform related files.
-How to verify it
show platform fan
show platform ssdhealth
show platform psustatus
show platform summary
show platform syseeprom
show platform temperature
show interface status
Why I did it
Power cycle test case fails for Z9332f in sonic-mgmt framework(#8605).
How I did it
Modified the platform API to return expected strings.
How to verify it
Power cycle the device and verify the reboot reason.
Run sonic-mgmt test_reboot script.
Catch up on fixes from BRCM SUG repo to pick up fixes after 5.0.0.6 all the way up to 5.0.0.8
Fixes include the following:
```
CS00012201827: Warmreboot causes syncd crash with SAI_API_UNSPECIFIED:syncdb_data_file_read:2230 Failed to parse JSON: error -2
DNX: Fix for ACL table create with v6 next hdr attr
and many unspecified changes that also went into 5.0.0.8
```
#### How to verify it
Preliminary tests looks fine on both XGS (gechiang) and DNX (judyjoseph)
On XGS testing done as following:
BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on 7260CX3 T0 DUT and all passed:
```
ipfwd/test_dir_bcast.py
fdb/test_fdb.py
fib/test_fib.py
vlan/test_valn.py
```
Also validated for for CS00012201827 (https://github.com/Azure/sonic-buildimage/issues/8300)
To enable saiserver docker on different platforms, it needs different configuration files. make the saiserver docker mount them in hwsku folder.
Co-authored-by: Ubuntu <richardyu@richardyu-ubuntu-vm0.trsxrdzozv2e1czsze2t05vqzh.ix.internal.cloudapp.net>
- Disable health monitoring of `psu.voltage` until support is implemented
- chassis: disable provisioning bit once linecard has booted
- chassis: fix issue in `show version` when running as `admin`
- chassis: fix race when reading an eeprom before it's available
- chassis: implement `get_all_asics` call
- api: fix `ChassisBase.get_system_eeprom_info` implementation
- api: add missing thermal condition and info
- api: fix return value of `ChassisBase.set_status_led`
- sfp: introduce SfpOptoeBase implementation used based on configuration knob
- psu: rely on pmbus to read input/output status when other mechanism is missing
- misc: other refactors and improvements
Why I did it
To monitor the SSD health condition in DellEMC S6100 platform post upgrade.
A daemon is introduced to monitor the SSD every one hour.
To check for SSD status at boot time and at the time of cold-reboot.
All these changes are supported only for newer SSD firmware.
Porting changes from 201911 branch
Added a platform_reboot_pre_check script to prevent cold-reboot based on SSD status.
Depends on Azure/sonic-utilities#1556
DO NOT MERGE UNTIL ABOVE PR IS MERGED
CPLD offset in led drv is incorrect.
#### How to verify it
echo 1 > brightness, show green on in DIAG led
echo 3 > brightness, show red on in DIAG led
echo 4 > brightness, show blue on in DIAG led
echo 5 > brightness, show green blinking in DIAG led
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
Why I did it
Support Nokia ixr7250E IMM and Supervisor cards
How I did it
Added modules x86_64-nokia_ixr7250e_sup-r0 and x86_64-nokia_ixr7250e_36x400g-r0 ../device/nokia directory.
Modified the platform/broadcom/one-image.mk to include NOKIA_IXR7250_PLATFORM_MODULE
Modified the platform/broadcom/rule.mk to include the platform-module-nokia.mk
The start template script that this value is used in will determine what
network namespace to use, and will add --net=host if it needs to run in
the host namespace.
With Docker 20.10, if --net=host is specified twice in docker run, then
it errors out. Therefore, remove the explicit --net=host in the run
options setting and let the start template script specify it.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Why I did it
fix the dx010 system eeprom unavailable issue
How I did it
enable the i2c slave 30ms timeout mechanism
How to verify it
i2cstress test in DX010 iSMT controller bus
Co-authored-by: nicwu-cel <nicwu@celestica.com>
Co-authored-by: Arun LK <Arun_L_K@dell.com>
Why I did it
Support for show system-health command in s5232f
How I did it
Added the configuration, API changes to support system health
How to verify it
Execute "show system-health summary/detail/monitor-list" CLI.
Why I did it
platform test suite failed for few API's in DellEMC Z9332f platform.
How I did it
Modified the API's to return the expected values in the script.
How to verify it
Run platform test suite after making the changes.
This change is to add a gbsyncd container to accommodate the syncd process and the SAI libraries for the Credo gearbox chips.
How I did it
This container works similar to the existing Broadcom syncd container. Its main difference is that the SAI-related dynamic libraries are replaced by the ones for Credo gearbox chips, and the container only reacts to SAI events for the gearbox chips. The SAI libraries will be provided by the package libsai-credo_1.0_amd64.deb.
For the image build, the added container will be built and included in the Broadcom platform image, after $(LIBSAI_CREDO)_URL = is replaced to the correct value. For now, as $(LIBSAI_CREDO)_URL is empty, the container build is skipped in the image build.
After the container is included in the image, in the runtime, the container will begin with checking the existence of /usr/share/sonic/hwsku/gearbox_config.json; if that file is not provided, the container will exit by itself. Therefore, for platforms unrelated to the Credo chips, as long as they are not providing the file, they will not be affected by this change.
Why I did it
Added a check in determining CPU reset in fast-/warm-reboot in their respective platform plugin.
Introducing reboot plugin for "reboot" command to handle its own platform plugin.
How I did it
On branch s6100_fast_warm_check
Changes to be committed:
(use "git reset HEAD ..." to unstage)
modified: ../../debian/platform-modules-s6100.install
modified: ../scripts/fast-reboot_plugin
modified: ../scripts/platform_reboot_override
new file: ../scripts/reboot_plugin
modified: ../scripts/track_reboot_reason.sh
modified: chassis.py
How to verify it
Triggered cold-reset inside fast-reboot to test out the reboot-cause 2.0 API.
Why I did it
serial-getty service exited in Dell S6100 device randomly.
How I did it
Added serial-getty to monit services.
How to verify it
Stop serial-getty in ssh session and check whether the service restarts or not.
- Improve chassis linecard restartability
- Fix 'show system-health' cli by adding non standard api
- Fix ledd crash on linecards with Recycle/Inband ports
- Refactor DPM management and add ADM1266 support
- Add state machine to update DPM RTC clock periodically
- Improve xcvr temperature reporting
- Fix lane mapping and `default_sku` for `x86_64-arista_7170_32c` platform
- Fix `7170-32C/CD` platform definition
Add needed code to pddf_custom_psu.c to deal with multi PSU and get SN.
How to verify it
Plugin new PSU (3Y) and test,
```
root@sonic:/sys/bus/i2c/drivers/psu/9-0050# cat psu_serial_num
S0A000X601919000013
root@sonic:/sys/bus/i2c/drivers/psu/9-0050# cat psu_model_name
YESM1300AM
root@sonic:/home/admin# pddf_psuutil mfrinfo
PSU Status Manufacturer ID Model Serial Fan Airflow Direction
PSU1 NOT OK 3Y POWER YESM1300AM S0A000X601919000007 exhaust
PSU2 OK 3Y POWER YESM1300AM S0A000X601919000013 exhaust
```
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Move SAI libraries for Broadcom for XGS and DNX families to 5.0.0.6
Included fixes
```
CS00012195263 | [4.3][5.0][TD3] Packets with broken IP headers received on VLAN interface are not dropped
CS00012192505 | [4.3] Re-encap IPinIP decap packets
CS00012192502 | [3.7.5.2] Start LED shell script execution on all DELL based platforms causing all ports flapping on SAI 3.7.5.2
CS00012191363 | [4.3] Support of memscan thread to detect TCAM parity error
CS00012190932 | [4.3] SAI_PORT_PFC_X_RX_PKTS incremented incorrectly even when no PFC frames are received on that priority
CS00012183901 | [4.3][WARMBOOT] WARMReboot with active traffic causes port flap reported during warm reboot
CS00011382163 | [4.4] Support warm-boot from 3.5 to 4.3
CS00011318937 | [4.3] MACSec SAI Support for Jericho2c+
CS00011318926 | [4.3] Provide SAI support for Jericho2c+
CS00012195263 | [4.3][5.0][TD3] Packets with broken IP headers received on VLAN interface are not dropped
CS00012195261 | [4.3][5.0][TD3]VLAN tagged IP packet received on untagged interface being routed instead of dropped
CS00012183901 | [4.3][WARMBOOT] WARMReboot with active traffic causes port flap reported during warm reboot
CS00012196056 | [4.3.3.8][WARMBOOT] syncd[2584]: segfault at 5616ad6c3d80 ip 00007f61e0c6bc65 sp 00007fff0c5a7a90 error 4 in libsai.so.1.0[7f61e0a95000+3cd8000]
CS00012195262 | [4.3][5.0][TD3] Malformed IP packet(missing IP header) received on a VLAN Interface is flooded to other LVAN members instead of being dropped
CS00012195956 | [4.3.3.8] [TD3]Syncd Crash at brcm_sai_tnl_mp_create_tunnel()
PR 4346163: Add support for AN/LT
```
- Why I did it
To fix failed test cases of Haliburton platform APIs that found on platform_tests script
- How I did it
Add device/celestica/x86_64-cel_e1031-r0/platform.json
Update functions to support python3.7
Add more functions follow latest sonic_platform_base
Fix the bug
- How to verify it
Run platform_tests script
Signed-off-by: Wirut Getbamrung [wgetbumr@celestica.com]
Why I did it
Update XGS and DNX SAI to 5.0.0.4 and additional flags needed in saibcm-modules
The following CSP's are merged in 5.0.0.4
CS00012182148 [4.3] Rate Limit Parity error message to syncd/sonic.
CS00012178692 [4.3] ACL drops counted as interface drops
CS00012183901 [4.3][WARMBOOT] WARMReboot with active traffic causes port flap reported during warm reboot
CS00012070713 [SAI 4.3 , DNX, 8690] Everflow ACL creation fails - brcm_sai_dnx_create_acl_table API fails, with unknown attribute error.
CS00012023263 [4.4] TD3/TH2 : Support 4 lossless queues(2 SW PFCWD and 2 HW PFCWD)
CS00012019578 [4.4] Pre FEC bit-error rate (BER) - DNX and XGS (TD and TH 50/100G)
How I did it
Changes the various make files to include the new SAI release + update the opennsl-modules.
Why I did it
We hit an issue recently in the chassis bringup where the linux bde attach failed with the following ioctl error.
[ 9058.585960] linux-user-bde (897363): Error: Invalid ioctl (00004c1d)
[ 9105.668237] linux-user-bde (901002): Error: Invalid ioctl (00004c1d)
Debugged with Broadcom team, who suggested to use this flag BCM_INSTANCE_SUPPORT to support multi-instance scenarios ( platforms with more than one asic where there are separate sai/syncd docker instances running controller each asic instance).
This flag was introduced since SDK-6.5.21 and need to be present in SAI and SAI GPL kernel module makefile.
How I did it
Add the flag in this flag BCM_INSTANCE_SUPPORT in gpl modules
Why I did it
To determine the revision of the pcie.yaml to be used based on BIOS version in DellEMC S6100 platform.
Depends on: Azure/sonic-platform-common#195
How I did it
Added two revisions of pcie.yaml pcie_1.yaml and pcie_2.yaml
Included a platform-specific Pcie class to provide the revision of the pcie.yaml to be used by pcieutil/pcied.
How to verify it
Execute pcieutil check (Azure/sonic-utilities#1672) command and verify the list of PCIe devices displayed.
Logs: UT_logs.txt
#### Why I did it
Support API 2.0 for S5248F platform
#### How I did it
Making changes to S5248F platform specific directory
Co-authored-by: Arun LK <Arun_L_K@dell.com>
#### Why I did it
The debian install files are required for installing sonic_platform packages
#### How I did it
Add install files to under debian folder
Co-authored-by: robert.hong <robert.hong@qct.io>
#### Why I did it
- To build flashrom properly with dependency tracking.
#### How I did it
- Moved flashrom code from platform/broadcom/sonic-platform-modules-dell/tools directory to src/flashrom directory.
- At the end, flashrom_0.9.7_amd64.deb package is build which will be installed in the devices.
- Currently flashrom builds only for Dell S6100 platforms.
Introduce new sonic-buildimage images for Broadcom DNX ASIC family.
sonic-broadcom-dnx.bin
sonic-aboot-broadcom-dnx.swi
How I did it
NO CHANGE to existing make commands
make init; make configure PLATFORM=broadcom; make target/sonic-aboot-broadcom.swi; make target/sonic-broadcom.bin
The difference now is that it will result in new broadcom images for DNX asic family as well.
sonic-broadcom.bin, sonic-broadcom-dnx.bin
sonic-aboot-broadcom.swi, sonic-aboot-broadcom-dnx.swi
Note: This PR also adds support for Broadcom SAI 5.0 (based on 1.8 SAI ) for DNX based platform + changes in platform x86_64-arista_7280cr3_32p4 bcm config files and platform_env.conf files
