* [syncd] warn shutdown syncd process when warm boot is enabled
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* [warmboot] mount folder to hold warmboot temporary files
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* Fix a typo
* [docker-orchagent]: Add vrfmgrd to supervisorctl
Signed-off-by: Marian Pritsak <marianp@mellanox.com>
* [sonic-vs]: Add vrfmgrd to supervisorctl
Signed-off-by: Marian Pritsak <marianp@mellanox.com>
* [device][platform] d6254qs d6556 platform porting
[device][platform] sensor and status led support for d7032q28b d7254q28b d7264q28b d6254qs d6556
[device][platform] qos support for d7032q28b d7254q28b
[device][platform] service configuration files for d7032q28b d7254q28b d7264q28b d6254qs d6556
* remove binary files and remove non-supported attributes in config.bcm
* remove gpio-ich here. file a PR in sonic-linux-kernel instead.
* remove unnecessary comments
* add GPL license
* Update ag9032v1 and ag9064 modules.
Signed-off-by: neal tai <neal.tai@deltaww.com>
* Fix the sfputil.py when convert an integer to hexadecimal without the 'L' trailing.
Signed-off-by: neal tai <neal.tai@deltaww.com>
Install a new FW by specifying FW path (mlnx-fw-upgrade.sh /path/to/FW)
or use default at '/etc/mlnx/fw-SPC.mfa'
Signed-off-by: Stepan Blyschak <stepanb@mellanox.com>
* [platform/haliburton] Fix kernel panic when remove smc module.
* [platform/haliburton] Chanage sysfs to support module interrupt
* [device/haliburton] Update sfputil to use new sysfs.
* [device/haliburton] sfputil to support xcvrd monitoring.
- Move front panel ports and port channels MTU and IP configurations out of
the current /etc/network/interfaces file and store them in the configuration
database.
- The default MTU value for both front panel ports and the port channels is
9100. They are set via the minigraph or 9100 by default.
- Introduce portmgrd which will pick up the MTU configurations from the
configuration database.
- The updated intfmgrd will pick up IP address changes from the configuration
database.
- Update sonic-swss submodule
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
led start bcm cmd triggers link state notifications.
This is quick fix to avoid such fake link state notifications.
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* [device]: Modify SFPUtil for inventec-d7032
[device]: Add front panel led support for Inventec-d7032
[platform]: Add transceiver monitor daemon for Inventec-d7032 and Inventec-d7054
* [device] follow new porting guide to have broadcom config under device folder
* remove license
* Fix potential blackholing/looping traffic and refresh ipv6 neighbor to avoid CPU hit
In case ipv6 global addresses were configured on L3 interfaces and used for peering,
and routing protocol was using link-local addresses on the same interfaces as prefered nexthops,
the link-local addresses could be aged out after a while due to no activities towards the link-local
addresses themselves. And when we receive new routes with the link-local nexthops, SONiC won't insert
them to the HW, and thus cause looping or blackholing traffic.
Global ipv6 addresses on L3 interfaces between switches are refreshed by BGP keeplive and other messages.
On server facing side, traffic may hit fowarding plane only, and no refresh for the ipv6 neighbor entries regularly.
This could age-out the linux kernel ipv6 neighbor entries, and HW neighbor table entries could be removed,
and thus traffic going to those neighbors would hit CPU, and cause traffic drop and temperary CPU high load.
Also, if link-local addresses were not learned, we may not get them at all later.
It is intended to fix all above issues.
Changes:
Add ndisc6 package in swss docker and use it for ipv6 ndp ping to update the neighbors' state on Vlan interfaces
Change the default ipv6 neighbor reachable timer to 30mins
Add periodical ipv6 multicast ping to ff02::11 to get/refresh link-local neighbor info.
* Fix review comments:
Add PORTCHANNEL_INTERFACE interface for ipv6 multicast ping
format issue
* Combine regular L3 interface and portchannel interface for looping
* Add ndisc6 package to vs docker
