Starting from build (master) 176 the warm reboot on BRCM Platform started to experience syncd crash. Upon further debug by Ying it was determined that the crash was related to the following new change:
[Dynamic buffer calc] Support dynamic buffer calculation (#1338)
Ying also debugged further and found The crash was caused by buffer pool profile setting operation SAI_BUFFER_PROFILE_ATTR_SHARED_DYNAMIC_TH
A case has filed with BRCM while a potential fix was tried by Ying that seems to have addressed this issue and we are making this change available in master branch so that it will allow further feature validation/testing especially in the warm reboot area.
Once an official fix is provided by BRCM, we will then remove this in house fix and apply the official fix.
- How to verify it
Just perform warm reboot with any master code 175 or above you should see this issue or issue the following cmd will also cause the crash: "mmuconfig -p egress_lossy_profile -a 0"
- Dynamically change EEPROM driver based on media type.
- Otherwise, EEPROM INFO and DOM INFO might not be fetched properly and will result in erroneous output.
Add a systemd dependency to make platform-modules service as a prerequisite for determine-reboot-cause service to ensure platform initialization is complete before determine-reboot-cause.service executes.
the control file version is 4.2.1.5-7
sonic$ sudo dpkg -i target/debs/buster/libsaibcm-dev_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm-dev_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm-dev (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm-dev (4.2.1.5-7) ...
lgh@491d842369cf:/sonic$ sudo dpkg -i target/debs/buster/libsaibcm_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm (4.2.1.5-7) ...
Processing triggers for libc-bin (2.28-10) ...
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
* [Mellanox] Update SAI to 1.18.0
* [Mellanox] Update SDK to 4.4.2112
* Updated Mellanox SAI to 1.18.0.2
* Updated bcmsai debians to use SAI 1.7.1
* Updated Mellanox to use SAI 1.7.1
* Updated submodule sonic-sairedis using SAI 1.7.1
Co-authored-by: Vineet Mittal <vmittalmittal@microsoft.com>
Co-authored-by: Nazarii Hnydyn <nazariig@nvidia.com>
bug fix: #5914
Validated for tx_disable function of SFP+ on AS7312-54X, AS5812-54X, AS5712-54x, and AS5812-54x.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
- Why I did it
To upgrade brcm syncd to buster
- How I did it
Updated BCM SAI using kernel version 4.19.0-12 and debian 10 to support buster.
Updated syncd docker from stretch to buster in sonic-buildimage
- How to verify it
Ensured docker is running synd buster.
After upgrade, ensured all BGP peers and ip interfaces are up.
Ping to BGP neighbors is working fine.
- Enhance eeprom parsing robustness on corrupted fields
- Add chassis provisioning service
- Disable CPU sleep state on some systems
- Complete refactor for FanSlots
- Fix module unload while still in use
- Why I did it
For determining reboot-cause while running newer BIOS, SMF firmware.
- How I did it
Made changes in reboot-cause determination script to add support for behavior of newer firmware.
- How to verify it
Performed different type of resets and verified "show reboot-cause" provides the correct reason.
Logs: UT_logs.txt
- Description for the changelog
DellEMC S6100: Update reboot-cause determination to support new firmware
- Change return type of SFP methods to match specification in sonic_platform_common/sfp_base.py
- Use init methods of base classes to initialize common instance variables
- Handle negative timeout values in S6100's watchdog ‘arm’ method
- Return appropriate values for 'get_target_speed', 'set_status_led' to avoid false warnings
- Implement platform module API
- Implement platform drawer API
- Complete and fix a few other platform API
- Add psu and fan support for chassis
- Fix dependency issue with determine-reboot-cause
* Update 50-ttyUSB-C0.rules
Remove some debug codes
* Update popmsg.sh
remove the debug info
* Update udev_prefix.sh
remove debug info
* Update platform-modules-haliburton.postinst
To enable the execute permission of udev scripts
* Update 50-ttyUSB-C0.rules
Fix port 13 - 48 plug out but not pop out message issue.
Signed-off-by: Jing Kan jika@microsoft.com
- Why I did it
Fix the i2c device to address conflicts behind the PCA9548 switch.
- How I did it
Load the i2c-mux-pca954x with parameter force-deselect-on-exit=1.
Submodule updates include the following commits:
* src/sonic-utilities 9dc58ea...f9eb739 (18):
> Remove unnecessary calls to str.encode() now that the package is Python 3; Fix deprecation warning (#1260)
> [generate_dump] Ignoring file/directory not found Errors (#1201)
> Fixed porstat rate and util issues (#1140)
> fix error: interface counters is mismatch after warm-reboot (#1099)
> Remove unnecessary calls to str.decode() now that the package is Python 3 (#1255)
> [acl-loader] Make list sorting compliant with Python 3 (#1257)
> Replace hard-coded fast-reboot with variable. And some typo corrections (#1254)
> [configlet][portconfig] Remove calls to dict.has_key() which is not available in Python 3 (#1247)
> Remove unnecessary conversions to list() and calls to dict.keys() (#1243)
> Clean up LGTM alerts (#1239)
> Add 'requests' as install dependency in setup.py (#1240)
> Convert to Python 3 (#1128)
> Fix mock SonicV2Connector in python3: use decode_responses mode so caller code will be the same as python2 (#1238)
> [tests] Do not trim from PATH if we did not append to it; Clean up/fix shebangs in scripts (#1233)
> Updates to bgp config and show commands with BGP_INTERNAL_NEIGHBOR table (#1224)
> [cli]: NAT show commands newline issue after migrated to Python3 (#1204)
> [doc]: Update Command-Reference.md (#1231)
> Added 'import sys' in feature.py file (#1232)
* src/sonic-py-swsssdk 9d9f0c6...1664be9 (2):
> Fix: no need to decode() after redis client scan, so it will work for both python2 and python3 (#96)
> FieldValueMap `contains`(`in`) will also work when migrated to libswsscommon(C++ with SWIG wrapper) (#94)
- Also fix Python 3-related issues:
- Use integer (floor) division in config_samples.py (sonic-config-engine)
- Replace print statement with print function in eeprom.py plugin for x86_64-kvm_x86_64-r0 platform
- Update all platform plugins to be compatible with both Python 2 and Python 3
- Remove shebangs from plugins files which are not intended to be executable
- Replace tabs with spaces in Python plugin files and fix alignment, because Python 3 is more strict
- Remove trailing whitespace from plugins files
Some syncd containers are still based on Debian Stretch, and thus do not have Python 3 available. For these containers, we must still rely on Python 2 to run supervisord_dependent_startup and supervisor-proc-exit-listener.
Fix 259 alerts reported by the LGTM tool:
- 245 for Unused import
- 7 for Testing equality to None
- 5 for Duplicate key in dict literal
- 1 for Module is imported more than once
- 1 for Unused local variable
**- Why I did it**
We were building a custom version of Supervisor because I had added patches to prevent hangs and crashes if the system clock ever rolled backward. Those changes were merged into the upstream Supervisor repo as of version 3.4.0 (http://supervisord.org/changes.html#id9), therefore, we should be able to simply install the vanilla package via pip. This will also allow us to easily move to Python 3, as Python 3 support was added in version 4.0.0.
**- How I did it**
- Remove Makefiles and patches for building supervisor package from source
- Install Python 3 supervisor package version 4.2.1 in Buster base container
- Also install Python 3 version of supervisord-dependent-startup in Buster base container
- Debian package installed binary in `/usr/bin/`, but pip package installs in `/usr/local/bin/`, so rather than update all absolute paths, I changed all references to simply call `supervisord` and let the system PATH find the executable to prevent future need for changes just in case we ever need to switch back to build a Debian package, then we won't need to modify these again.
- Install Python 2 supervisor package >= 3.4.0 in Stretch and Jessie base containers
This release includes changes for supporting Debian Buster, fixes for internally found issues and more enhancement related to spec coverage and feature parity for Broadcom ASICs.
Additional fixes included:
CS00011465498 - Warm reboot
CS00011465061 - interfaces not coming up
CS00011396506 - nexthop resource leak
CS00011452080 - BCM SAI crash while getting lane count
This change introduces PDDF which is described here: https://github.com/Azure/SONiC/pull/536
Most of the platform bring up effort goes in developing the platform device drivers, SONiC platform APIs and validating them. Typically each platform vendor writes their own drivers and platform APIs which is very tailor made to that platform. This involves writing code, building, installing it on the target platform devices and testing. Many of the details of the platform are hard coded into these drivers, from the HW spec. They go through this cycle repetitively till everything works fine, and is validated before upstreaming the code.
PDDF aims to make this platform driver and platform APIs development process much simpler by providing a data driven development framework. This is enabled by:
JSON descriptor files for platform data
Generic data-driven drivers for various devices
Generic SONiC platform APIs
Vendor specific extensions for customisation and extensibility
Signed-off-by: Fuzail Khan <fuzail.khan@broadcom.com>
* [Juniper] Platform bug fixes / improvements
This patch set introduces the following changes for
the two platforms.
- QFX5210
- Fixes a driver bug related to reboot notifier
- Disable pcied
- Introduces a wrapper script for fast / warm reboots
for unloading the driver containing reboot handler
- Support for PSM4 optics in media_settings
- QFX5200
- BCM configuration file updates
- Bug fixes for EM policy
- Fixes a driver bug related to reboot notifier
- Introduces a wrapper script for fast / warm reboots
for unloading the driver containing reboot handler
- Disable pcied
- Support for PSM4 optics
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
The original code tried to initialize PCA9541 without having the
driver loaded. As result the initialization didn't take effect.
Recently PCA9541 driver was added to the kernel and since then
the initialization takes effect and has negatively impacted the
platform stability.
Commenting the initialization code out to restore the original
behavior while analyzing further.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
Why/How I did:
Make sure first error syslog is triggered based on FAULT TOLERANCE condition.
Added support of repeat clause with alert action. This is used as trigger
for generation of periodic syslog error messages if error is persistent
Updated the monit conf files with repeat every x cycles for the alert action
- Change `/run/arista` mount to pmon by `/var/run/platform_cache`
- Python3 by default for Arista platform initialisation
- Fix outstanding py2/3 compatibility issues (eeprom mostly)
- Use pytest for unit testing
- Miscellaneous modular fixes
- Implement FanDrawer and get_high_critical_threshold Platform API for S6000, S6100, Z9100 and Z9264F.
- Fix incorrect fan direction values in S6100, Z9100
- Enable thermalctld support for our platforms
- Fix Chassis.get_num_sfp which had an off by one
- Implement read_eeprom and write_eeprom in SfpBase
- Refactor of Psus and PsuSlots. Psus they are now detected and metadata reported
- Improvements to modular support
Co-authored-by: Zhi Yuan Carl Zhao <zyzhao@arista.com>
The `get_serial_number()` method in the ChassisBase and ModuleBase classes was redundant, as the `get_serial()` method is inherited from the DeviceBase class. This method was removed from the base classes in sonic-platform-common and the submodule was updated in https://github.com/Azure/sonic-buildimage/pull/5625.
This PR aligns the existing vendor platform API implementations to remove the `get_serial_number()` methods and ensure the `get_serial()` methods are implemented, if they weren't previously.
Note that this PR does not modify the Dell platform API implementations, as this will be handled as part of https://github.com/Azure/sonic-buildimage/pull/5609
- Make DellEMC platform modules Python3 compliant.
- Change return type of PSU Platform APIs in DellEMC Z9264, S5232 and Thermal Platform APIs in S5232 to 'float'.
- Remove multiple copies of pcisysfs.py.
- PEP8 style changes for utility scripts.
- Build and install Python3 version of sonic_platform package.
- Fix minor Platform API issues.
- The issue is that the SAI package content is changed without changing its version. The DPKG caches the wrong version of SAI package.
- The fix is to include the SAI package content header for SHA calcaulation. This will detect if there is any change in the SAI package.
During platform deinitialization, dell_ich is not removed properly and when we do initialize s6100 platform, ICH driver sysfs attributes are not attached. Because of this, get_transceiver_change_event returns error and this leads xcvrd to crash.
Some platforms don't leverage the brcm led coprocessor.
However ledinit will try to load a non existing file and exit with an
error code.
This change is a cosmetic fix mostly.
- How to verify it
Boot a platform without the configuration and verify in the syslog that the exit status of ledinit is 0
Boot a platform with the configuration and verify in the syslog that the exit status of ledinit is 0 and the leds are working.
Verified by adding a dumb led_proc_init.soc on an Arista platform which usually doesn't use it.
We want to let Monit to unmonitor the processes in containers which are disabled in `FEATURE` table such that
Monit will not generate false alerting messages into the syslog.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
- Why I did it
For fixing PCA MUX attachment issue in Dell S6100 platform.
- How I did it
Wait till IOM MUX powered up properly and start I2C enumeration.
We are moving toward building all Python packages for SONiC as wheel packages rather than Debian packages. This will also allow us to more easily transition to Python 3.
Python files are now packaged in "sonic-utilities" Pyhton wheel. Data files are now packaged in "sonic-utilities-data" Debian package.
**- How I did it**
- Build and install sonic-utilities as a Python package
- Remove explicit installation of wheel dependencies, as these will now get installed implicitly by pip when installing sonic-utilities as a wheel
- Build and install new sonic-utilities-data package to install data files required by sonic-utilities applications
- Update all references to sonic-utilities scripts/entrypoints to either reference the new /usr/local/bin/ location or remove absolute path entirely where applicable
Submodule updates:
* src/sonic-utilities aa27dd9...2244d7b (5):
> Support building sonic-utilities as a Python wheel package instead of a Debian package (#1122)
> [consutil] Display remote device name in show command (#1120)
> [vrf] fix check state_db error when vrf moving (#1119)
> [consutil] Fix issue where the ConfigDBConnector's reference is missing (#1117)
> Update to make config load/reload backward compatible. (#1115)
* src/sonic-ztp dd025bc...911d622 (1):
> Update paths to reflect new sonic-utilities install location, /usr/local/bin/ (#19)
- Merge chassis codebase upstream
- Add support for Otterlake supervisor
- Add support for NorthFace and Camp chassis
- Add support for Eldridge, Dragonfly and Brooks fabrics
- Add support for Clearwater2 and Clearwater2Ms linecards
- Add new arista Cli to power on/off cards
- Add new arista show Cli to inspect supervisor, chassis, fabrics and linecards
- Finish the refactor of the smbus backend (huge performance enhencement)
- Split scd-hwmon kernel module in multiple source files
- Add new scd-uart driver to manage linecard consoles within a chassis
- Bootstrap of thermal platform API implementation
- Fix psud led error message
- Fix fan led color on Smartsville
When stopping the swss, pmon or bgp containers, log messages like the following can be seen:
```
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,061 ERRO pool dependent-startup event buffer overflowed, discarding event 34
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,063 ERRO pool dependent-startup event buffer overflowed, discarding event 35
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,064 ERRO pool dependent-startup event buffer overflowed, discarding event 36
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,066 ERRO pool dependent-startup event buffer overflowed, discarding event 37
```
This is due to the number of programs in the container managed by supervisor, all generating events at the same time. The default event queue buffer size in supervisor is 10. This patch increases that value in all containers in order to eliminate these errors. As more programs are added to the containers, we may need to further adjust these values. I increased all buffer sizes to 25 except for containers with more programs or templated supervisor.conf files which allow for a variable number of programs. In these cases I increased the buffer size to 50. One final exception is the swss container, where the buffer fills up to ~50, so I increased this buffer to 100.
Resolves https://github.com/Azure/sonic-buildimage/issues/5241
Original converting from register is wrong, it makes the fan speed much higher than it is. Change the way fan speed is calculated from CPLD.
Signed-off-by: roy_lee <roy_lee@accton.com>
HW set qsfp port to reset at default. so need SW to set to normal when boot.
1. Modify cpld driver to invert reset offset value
2. Set to normal when boot.
* Moving BRCM SAI from 3.7.5.1-1 to 3.7.5.1-2 to pick up the stubbed SAI API that were present in the header but missing in SAI implementation that cause link error during build.
In SAI header 1.5.2 there are defined SAI APIs such as "sai_query_attribute_capability()" and few other APIs that were missing the stub code in BRCM 3.7.5.1 SAI code delivery. This causes linking issue during build when we implemented the common handler to support "sai_query_attribute_capability()" that other platform supports. The expectation is that all SAI vendors must implement all the SAI header defined SAI APIs by stubbing those that they don't have the actual code support to return "SAI_STATUS_NOT_IMPLEMENTED". This allows common code for all platforms to be developed without having linking issue during build for all platforms. BRCM has provided the patch code and this PR moves the BRCM SAI from 3.7.5.1-1 to 3.7.5.1-2 to pick up those missing stubbed SAI APIs.
See BRCM case CS00010790550 for more details
As part of consolidating all common Python-based functionality into the new sonic-py-common package, this pull request:
1. Redirects all Python applications/scripts in sonic-buildimage repo which previously imported sonic_device_util or sonic_daemon_base to instead import sonic-py-common, which was added in https://github.com/Azure/sonic-buildimage/pull/5003
2. Replaces all calls to `sonic_device_util.get_platform_info()` to instead call `sonic_py_common.get_platform()` and removes any calls to `sonic_device_util.get_machine_info()` which are no longer necessary (i.e., those which were only used to pass the results to `sonic_device_util.get_platform_info()`.
3. Removes unused imports to the now-deprecated sonic-daemon-base package and sonic_device_util.py module
This is the next step toward resolving https://github.com/Azure/sonic-buildimage/issues/4999
Also reverted my previous change in which device_info.get_platform() would first try obtaining the platform ID string from Config DB and fall back to gathering it from machine.conf upon failure because this function is called by sonic-cfggen before the data is in the DB, in which case, the db_connect() call will hang indefinitely, which was not the behavior I expected. As of now, the function will always reference machine.conf.
* [platform] Add Support For Environment Variable
This PR adds the ability to read environment file from /etc/sonic.
the file contains immutable SONiC config attributes such as platform,
hwsku, version, device_type. The aim is to minimize calls being made
into sonic-cfggen during boot time.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
when parallel build is enabled, both docker-fpm-frr and docker-syncd-brcm
is built at the same time, docker-fpm-frr requires swss which requires to
install libsaivs-dev. docker-syncd-brcm requires syncd package which requires
to install libsaibcm-dev.
since libsaivs-dev and libsaibcm-dev install the sai header in the same
location, these two packages cannot be installed at the same time. Therefore,
we need to serialize the build between these two packages. Simply uninstall
the conflict package is not enough to solve this issue. The correct solution
is to have one package wait for another package to be uninstalled.
For example, if syncd is built first, then it will install libsaibcm-dev.
Meanwhile, if the swss build job starts and tries to install libsaivs-dev,
it will first try to query if libsaibcm-dev is installed or not. if it is
installed, then it will wait until libsaibcm-dev is uninstalled. After syncd
job is finished, it will uninstall libsaibcm-dev and swss build job will be
unblocked.
To solve this issue, _UNINSTALLS is introduced to uninstall a package that
is no longer needed and to allow blocked job to continue.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Align SFP key names with new standard defined in https://github.com/Azure/sonic-platform-common/pull/97
- hardwarerev -> hardware_rev
- serialnum -> serial
- manufacturename -> manufacturer
- modelname -> model
- Connector -> connector
1) Fixing the issues while applying platform TxCTLE settings in sfputil.py for QFX5200
2) Adding the support for transceiver dom threshold info in sfputil.py for both QFX5210 & QFX5200 platforms
3) Updating the sfputil.py for QFX5210 & QFX5200 platforms
4) Adding a new platform specific command 'show_thresholds' to display the FAN dutycycle percentage for various temperature ranges (for both AFI & AFO QFX5200 systems).
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
This PR has changes to support accessing the bcmsh and bcmcmd utilities on multi ASIC devices
Changes done
- move the link of /var/run/sswsyncd from docker-syncd-brcm.mk to docker_image_ctl.j2
- update the bcmsh and bcmcmd scripts to take -n [ASIC_ID] as an argument on multi ASIC platforms
- Xilinx/pericom peripherals are not actively used in DellEMC S6100 switch.
- These peripherals are throwing PCIE corrected messages in some of the units and filling syslog.
- Since it is not usable disabling it at startup.
make swss build depends only on libsairedis instead of syncd. This allows to build swss without depending
on vendor sai library.
Currently, libsairedis build also buils syncd which requires vendor SAI lib. This makes difficult to build
swss docker in buster while still keeping syncd docker in stretch, as swss requires libsairedis which also
build syncd and requires vendor to provide SAI for buster. As swss docker does not really contain syncd
binary, so it is not necessary to build syncd for swss docker.
* [submodule]: update sonic-sairedis
* ccbb3bc 2020-06-28 | add option to build without syncd (HEAD, origin/master, origin/HEAD) [Guohan Lu]
* 4247481 2020-06-28 | install saidiscovery into syncd package [Guohan Lu]
* 61b8e8e 2020-06-26 | Revert "sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624)" (#630) [Danny Allen]
* 85e543c 2020-06-26 | add a README to tests directory to describe how to run 'make check' (#629) [Syd Logan]
* 2772f15 2020-06-26 | sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624) [Syd Logan]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
This patch addresses the following issues:
1) Platform drivers were not loading in the latest images. Fixed
the intialization script to make sure that all the drivers are
loaded.
2) Getting rid of "pstore: crypto_comp_decompress failed, ret = -22!"
messages during the kernel boot, after moving to 4.19 kernel. The
solution is to remove the files under '/sys/fs/pstore' directory.
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
**- Why I did it**
Initially, the critical_processes file contains either the name of critical process or the name of group.
For example, the critical_processes file in the dhcp_relay container contains a single group name
`isc-dhcp-relay`. When testing the autorestart feature of each container, we need get all the critical
processes and test whether a container can be restarted correctly if one of its critical processes is
killed. However, it will be difficult to differentiate whether the names in the critical_processes file are
the critical processes or group names. At the same time, changing the syntax in this file will separate the individual process from the groups and also makes it clear to the user.
Right now the critical_processes file contains two different kind of entries. One is "program:xxx" which indicates a critical process. Another is "group:xxx" which indicates a group of critical processes
managed by supervisord using the name "xxx". At the same time, I also updated the logic to
parse the file critical_processes in supervisor-proc-event-listener script.
**- How to verify it**
We can first enable the autorestart feature of a specified container for example `dhcp_relay` by running the comman `sudo config container feature autorestart dhcp_relay enabled` on DUT. Then we can select a critical process from the command `docker top dhcp_relay` and use the command `sudo kill -SIGKILL <pid>` to kill that critical process. Final step is to check whether the container is restarted correctly or not.
**- Why I did it**
After discussed with Joe, we use the string "/usr/bin/syncd\s" in Monit configuration file to monitor
syncd process on Broadcom and Mellanox. Due to my careless, I did not find this bug during the
previous testing. If we use the string "/usr/bin/syncd" in Monit configuration file to monitor the
syncd process, Monit will not detect whether syncd process is running or not.
If we ran the command `sudo monit procmactch “/usr/bin/syncd”` on Broadcom, there will be three
processes in syncd container which matched this "/usr/bin/syncd": `/bin/bash /usr/bin/syncd.sh
wait`, `/usr/bin/dsserve /usr/bin/syncd –diag -u -p /etc/sai.d/sai.profile` and `/usr/bin/syncd –diag -
u -p /etc/sai.d/said.profile`. Monit will select the processes with the highest uptime (at there
`/bin/bash /usr/bin/syncd.sh wait`) to match and did not select `/usr/bin/syncd –diag -u -p
/etc/sai.d/said.profile` to match.
Similarly, On Mellanox Monit will also select the process with the highest uptime (at there
`/bin/bash /usr/bin/syncd.sh wait`) to match and did not select `/usr/bin/syncd –diag -u -p
/etc/sai.d/said.profile` to match.
That is why Monit is unable to detect whether syncd process is running or not if we use the string “/usr/bin/syncd” in Monit configuration file. If we use the string "/usr/bin/syncd\s" in Monit configuration file, Monit can filter out the process `/bin/bash /usr/bin/syncd.sh wait` and thus can correctly monitor the syncd process.
**- How I did it**
**- How to verify it**
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
**- Why I did it**
The tx_disable function isn't work for the accton_ax5835-54x device.
**- How I did it**
Fix the incorrect path of the sfp node path inside the util file.
**- How to verify it**
Test with
"sudo accton_as5835_54x_util.py show"
"sudo accton_as5835_54x_util.py set sfp"
There should see correct value for module_present and module_tx_disable. And should able to set it.
Signed-off-by: kuanyu_chen <kuanyu_chen@edge-core.com>
- Add .gitignore files in each subdirectory of src/, so as to reduce the size of the .gitignore file in the project root, and also make it easier to maintain (i.e., if a directory in src/ is removed, there will not be outdated entries in the root .gitignore file.
- Also add missing .gitignore entries and remove outdated entries and duplicates.
**- Why I did it**
For decoding system EEPROM of S6000 based on Dell offset format and S6000-ON’s system EEPROM in ONIE TLV format.
**- How I did it**
- Differentiate between S6000 and S6000-ON using the product name available in ‘dmi’ ( “/sys/class/dmi/id/product_name” )
- For decoding S6000 system EEPROM in Dell offset format and updating the redis DB with the EEPROM contents, added a new class ‘EepromS6000’ in eeprom.py,
- Renamed certain methods in both Eeprom, EepromS6000 classes to accommodate the plugin-specific methods.
**- How to verify it**
- Use 'decode-syseeprom' command to list the system EEPROM details.
- Wrote a python script to load chassis class and call the appropriate methods.
UT Logs: [S6000_eeprom_logs.txt](https://github.com/Azure/sonic-buildimage/files/4735515/S6000_eeprom_logs.txt), [S6000-ON_eeprom_logs.txt](https://github.com/Azure/sonic-buildimage/files/4735461/S6000-ON_eeprom_logs.txt)
Test script: [eeprom_test_py.txt](https://github.com/Azure/sonic-buildimage/files/4735509/eeprom_test_py.txt)
- Sensor and Fan information added to primary platforms for thermal API.
- Refactors involving better abstractions, code reuse and dead code removal.
- Improvements to the diag capabilities
- Pylintrc added to improve code quality. Will become fatal at a later time.
Co-authored-by: Baptiste Covolato <baptiste@arista.com>
* Update sonic-sairedis (sairedis with SAI 1.6 headers)
* Update SAIBCM to 3.7.4.2, which is built upon SAI1.6 headers
* missed updating BRCM_SAI variable, fixed it
* Update SAIBCM to 3.7.4.2, updated link to libsaibcm
* [Mellanox] Update SAI (release:v1.16.3; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* Update sonic-sairedis pointer to include SAI1.6 headers
* [Mellanox] Update SDK to 4.4.0914 and FW to xx.2007.1112 to match SAI 1.16.3 (API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* ensure the veth link is up in docker VS container
* ensure the veth link is up in docker VS container
* [Mellanox] Update SAI (release:v1.16.3.2; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* use 'config interface startup' instead of using ifconfig command, also undid the previous change'
Co-authored-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
- Skip thermalctld in DellEMC S6000, S6100, Z9100 and Z9264 platforms.
- Change the return type of thermal Platform APIs in DellEMC S6000, S6100, Z9100 and Z9264 platforms to 'float'.
* [platform]: Add a new supported platform, Delta-agc032
Switch Vendor: Delta
Switch SKU: Delta-agc032
CPU: BROADWELL-DE
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk3, BCM56980
Port Configuration: 32x400G + 2x10G
- What I did
Add a new Delta platform Delta-agc032.
- How I did it
Add files by following SONiC Porting Guide.
- How to verify it
1. decode-syseeprom
2. sensors
3. psuutil
4. sfputil
5. show interface status
6. bcmcmd
Signed-off-by: zoe-kuan <ZOE.KUAN@deltaww.com>
3y Power YPEB-1200am PSU doens't support read fan_dir from pmbus register
Check with vendor this PUS type only support F2B fan direction. So add to show "F2B"
when red psu_fan_dir sysfs.
For detecting transceiver change events through xcvrd in DellEMC S6000, S6100 and Z9100 platforms.
- In S6000, rename 'get_transceiver_change_event' in chassis.py to 'get_change_event' and return appropriate values.
- In S6100, implement 'get_change_event' through polling method (poll interval = 1 second) in chassis.py (Transceiver insertion/removal does not generate interrupts due to a CPLD bug)
- In Z9100, implement 'get_change_event' through interrupt method using select.epoll().
This patchset implement the following:
- Setting the FAN frequency
- Corrections to the EM policy with respect to platform
defined temperature / fan values
- Updates to the platform monitorng script logging
- Fixes to platform initialization script
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
- Add Makefile rules to build debug containers for SWI images
- Fix some platform API implementation for xcvrd and thermalctld
- Improvements to arista diag command
- Miscellaneous refactors
Co-authored-by: Maxime Lorrillere <mlorrillere@arista.com>
This patch set implements the following:
- Fixes the conflicts in chassis.py / platform.py in sonic_platfrom
- Consolidating the common library files in sonic_platform
- Moving QFX5210 specific drivers to qfx5210/modules
- Moving Juniper common fpga drivers to common/modules
- Cleaning up the platform driver files
- Bug fixes in QFX5210 platform monitor & initialiazation script
- Fixing the bugs in QFX5210 eeprom parsing
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
[baseimage]: upgrade base image to debian buster
bring up the base image to debian buster 4.19 kernel.
using the merge commits to preserve the individual commits to better track the history.
1. undefine led_classdev_register as it is defined in leds.h
2. header file location change
a. linux/i2c/pmbus.h -> linux/pmbus.h
b. linux/i2c-mux-gpio.h -> linux/platform_data/i2c-mux-gpio.h
c. linux/i2c/pca954x.h -> linux/platform_data/pca954x.h
- build SONIC_STRETCH_DOCKERS in sonic-slave-stretch docker
- build image related module in sonic-slave-buster docker.
This includes all kernels modules and some packages
Signed-off-by: Guohan Lu <lguohan@gmail.com>
This is a 1RU switch with 32 QSFP28 (40G/100G) ports on
Broadcom Tomahawk I chipset. CPU used in QFX5200-32C-S
is Intel Ivy Bridge. The machine has Redundant and
hot-swappable Power Supply (1+1) and also has Redundant
and hot swappable fans (5).
Signed-off-by: Ciju Rajan K <crajank@juniper.net>
Signed-off-by: Ashish Bhensdadia <bashish@juniper.net>
FPGA driver crash fix for stale buffer in i2c transfer
LED firmware load issue fix.
10G port swapfix
psu/sfp bug fixes to report correct states/status of hw
In the file "files/build_templates/docker_image_ctl.j2", it adds the option
"--net" to the docker create command through the commit
"abe7ef7e2e2e1215c97cee19a83aab0b130cebe5" (#3856).
Remove the "--net" option in "docker-syncd-brcm-rpc.mk" to avoid
specifying duplicated "--net" options.
Signed-off-by: charlie_chen <charlie_chen@edge-core.com>
DPKG caching framework provides the infrastructure to cache the sonic module/target .deb files into a local cache by tracking the target dependency files.SONIC build infrastructure is designed as a plugin framework where any new source code can be easily integrated into sonic as a module and that generates output as a .deb file. The source code compilation of a module is completely independent of other modules compilation. Inter module dependency is resolved through build artifacts like header files, libraries, and binaries in the form of Debian packages. For example module A depends on module B. While module A is being built, it uses B's .deb file to install it in the build docker.
The DPKG caching framework provides an infrastructure that caches a module's deb package and restores it back to the build directory if its dependency files are not modified. When a module is compiled for the first time, the generated deb package is stored at the DPKG cache location. On the subsequent build, first, it checks the module dependency file modification. If none of the dependent files is changed, it copies the deb package from the cache location, otherwise, it goes for local compilation and generates the deb package. The modified files should be checked-in to get the newer cache deb package.
This provides a huge improvement in build time and also supports the true incremental build by tracking the dependency files.
- How I did it
It takes two global arguments to enable the DPKG caching, the first one indicates the caching method and the second one describes the location of the cache.
SONIC_DPKG_CACHE_METHOD=cache
SONIC_DPKG_CACHE_SOURCE=
where SONIC_DPKG_CACHE_METHOD - Default method is 'cache' for deb package caching
none: no caching
cache: cache from local directory
Dependency file tracking:
Dependency files are tracked for each target in two levels.
1. Common make infrastructure files - rules/config, rules/functions, slave.mk etc.
2. Per module files - files which are specific to modules, Makefile, debian/rules, patch files, etc.
For example: dependency files for Linux Kernel - src/sonic-linux-kernel,
SPATH := $($(LINUX_HEADERS_COMMON)_SRC_PATH)
DEP_FILES := $(SONIC_COMMON_FILES_LIST) rules/linux-kernel.mk rules/linux-kernel.dep
DEP_FILES += $(SONIC_COMMON_BASE_FILES_LIST)
SMDEP_FILES := $(addprefix $(SPATH)/,$(shell cd $(SPATH) && git ls-files))
DEP_FLAGS := $(SONIC_COMMON_FLAGS_LIST) \
$(KERNEL_PROCURE_METHOD) $(KERNEL_CACHE_PATH)
$(LINUX_HEADERS_COMMON)_CACHE_MODE := GIT_CONTENT_SHA
$(LINUX_HEADERS_COMMON)_DEP_FLAGS := $(DEP_FLAGS)
$(LINUX_HEADERS_COMMON)_DEP_FILES := $(DEP_FILES)
$(LINUX_HEADERS_COMMON)_SMDEP_FILES := $(SMDEP_FILES)
$(LINUX_HEADERS_COMMON)_SMDEP_PATHS := $(SPATH)
Cache file tracking:
The Cache file is a compressed TAR ball of a module's target DEB file and its derived-target DEB files.
The cache filename is formed with the following format
FORMAT:
<module deb filename>.<24 byte of DEP SHA hash >-<24 byte of MOD SHA hash>.tgz
Eg:
linux-headers-4.9.0-9-2-common_4.9.168-1+deb9u3_all.deb-23658712fd21bb776fa16f47-c0b63ef593d4a32643bca228.tgz
< 24-byte DEP SHA value > - the SHA value is derived from all the dependent packages.
< 24-byte MOD SHA value > - the SHA value is derived from either of the following.
GIT_COMMIT_SHA - SHA value of the last git commit ID if it is a submodule
GIT_CONTENT_SHA - SHA value is generated from the content of the target dependency files.
Target Specific rules:
Caching can be enabled/disabled on a global level and also on the per-target level.
$(addprefix $(DEBS_PATH)/, $(SONIC_DPKG_DEBS)) : $(DEBS_PATH)/% : .platform $$(addsuffix -install,$$(addprefix $(DEBS_PATH)/,$$($$*_DEPENDS))) \
$(call dpkg_depend,$(DEBS_PATH)/%.dep )
$(HEADER)
# Load the target deb from DPKG cache
$(call LOAD_CACHE,$*,$@)
# Skip building the target if it is already loaded from cache
if [ -z '$($*_CACHE_LOADED)' ] ; then
.....
# Rules for Generating the target DEB file.
.....
# Save the target deb into DPKG cache
$(call SAVE_CACHE,$*,$@)
fi
$(FOOTER)
The make rule-'$(call dpkg_depend,$(DEBS_PATH)/%.dep )' checks for target dependency file modification. If it is newer than the target, it will go for re-generation of that target.
Two main macros 'LOAD_CACHE' and 'SAVE_CACHE' are used for loading and storing the cache contents.
The 'LOAD_CACHE' macro is used to load the cache file from cache storage and extracts them into the target folder. It is done only if target dependency files are not modified by checking the GIT file status, otherwise, cache loading is skipped and full compilation is performed.
It also updates the target-specific variable to indicate the cache is loaded or not.
The 'SAVE_CACHE' macro generates the compressed tarball of the cache file and saves them into cache storage. Saving into the cache storage is protected with a lock.
- How to verify it
The caching functionality is verified by enabling it in Linux kernel submodule.
It uses the cache directory as 'target/cache' where Linux cache file gets stored on the first-time build and it is picked from the cache location during the subsequent clean build.
- Description for the changelog
The DPKG caching framework provides the infrastructure to save the module-specific deb file to be cached by tracking the module's dependency files.
If the module's dependency files are not changed, it restores the module deb files from the cache storage.
- Description for the changelog
- A picture of a cute animal (not mandatory but encouraged)
DOCUMENT PR:
https://github.com/Azure/SONiC/pull/559
Due to linux create hwmonN node number, N isn't fixed. So modify to use "" to let thermal.py can correct sysfs. For example, use /sys/bus/i2c/devices/55-0048/hwmon/hwmon/temp1_input to instead of /sys/bus/i2c/devices/55-0048/hwmon/hwmon4/temp1_input
This patch upgrade the kernel from version
4.9.0-9-2 (4.9.168-1+deb9u3) to 4.9.0-11-2 (4.9.189-3+deb9u2)
Co-authored-by: rajendra-dendukuri <47423477+rajendra-dendukuri@users.noreply.github.com>
- Fix for Azure/sonic-buildimage#4095
- Exit status from failed make command(action) didnt reached parent target because the make command is inside the "for" loop.
- Only the exit status of the last command in the last iteration of the for loop is read by parent target.
- This is the reason why dpkg-buildpackage ignored the make error.
- Fixed the issue with help of "set -e".
- Added support for Thermal event in Last Reboot Reason "show reboot-cause" command.
- Added support for sending log message in case of thermal shutdown.
sonic NOTICE root: Shutting down due to over temperature (40 degree, 30 degree, 34 degree)
