During ISSU, "mlxsw_minimal" driver still trying to access firmware, in some cases FW could return some wrong critical threshold value which will cause switch shutdown.
**- How I did it**
In order to prevent "mlxsw_minimal" driver from accessing ASIC during ISSU, SDK will raise "OFFLINE" 'udev' event
at the early beginning of such flow. When this event is received, hw-management will remove "mlxsw_minimal" driver.
There is no need to implement the opposite "ONLINE" event since this flow is ended up with "kexec".
**- How to verify it**
repeatedly perform warm reboot, make sure there is no switch shutdown occurred.
* Fix exception in bgpmon caused by duplicate keys
It is possible that BGP neighbors in IPv4 and IPv6 address families
share the same name (such as bgp monitor). However, such case is not
handled in bgpmon, and an Exception will be raised. This commit will
address the issue by Using set instead of list to avoid duplicate keys.
Bugs fixes:
All | Kernel | During system reload when CPU is loaded with heavy traffic, a Kernel Panic may occur.
All | Modules, Port split | FW stuck when device rebooted with locked Optical Transceivers in split mode
Spectrum-3 | PFC | On Spectrum-3 systems, slow reaction time to Rx pause packets on 40GbE ports may lead to buffer overflow on servers.
Spectrum-3 | SN4700, Port Split | On rare occasion SN4700, conducting 100G split (4x25G) in NRZ when splitter port 1 or 2 are down, ports 3 and 4 will also go down.
Enahncments:
All | Kernel | new notification on ISSU start, so other kernel drivers can disable any interface to ASIC
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Recent changes brought l2 vlan concept which do not have DHCP
clients behind them and so DHCP relay is not required. Also,
dhcpmon fails to launch on those vlans as their interfaces
lack IP addresses. This PR limit launch of both DHCP relay
and dhcpmon to L3 vlans only.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
- Support for non-template based FRR configurations (BGP, route-map, OSPF, static route..etc) using config DB schema.
- Support for save & restore - Jinja template based config-DB data read and apply to FRR during startup
**- How I did it**
- add frrcfgd service
- when frr_mgmg_framework_config is set, frrcfgd starts in bgp container
- when user changed the BGP or other related table entries in config DB, frrcfgd will run corresponding VTYSH commands to program on FRR.
- add jinja template to generate FRR config file to be used by FRR daemons while bgp container restarted
**- How to verify it**
1. Add/delete data on config DB and then run VTYSH "show running-config" command to check if FRR configuration changed.
1. Restart bgp container and check if generated FRR config file is correct and run VTYSH "show running-config" command to check if FRR configuration is consistent with attributes in config DB
Co-authored-by: Zhenhong Zhao <zhenhong.zhao@dell.com>
**- Why I did it**
For now `hwsku.json` and `platform.json` dont support optional fields. For example no way to add `fec` or `autoneg` field using `platform.json` and `hwsku.json`.
**- How I did it**
Added parsing of optional fields from hwsku.json.
**- How to verify it**
Add optional field to `hwsku.json`. After first boot will be generated new `config_db.json` or you can generate it using `sonic-cfggen` command. In this file must be optional field from `hwsku.json` or check using command `redis-cli hgetall PORT_TABLE:Ethernet0`
Example of `hwsku.json`, that must be parsed:
```
{
"interfaces": {
"Ethernet0": {
"default_brkout_mode": "1x100G[40G]",
"fec": "rs",
"autoneg": "0"
},
...
}
```
Example of generated `config_db.json`:
```
"PORT": {
"Ethernet0": {
"alias": "Ethernet0",
"lanes": "0,1,2,3",
"speed": "100000",
"index": "1",
"admin_status": "up",
"fec": "rs",
"autoneg": "0",
"mtu": "9100"
},
```
So, we can see this entries in redis db:
```
admin@sonic:~$ redis-cli hgetall PORT_TABLE:Ethernet0
1) "alias"
2) "Ethernet0"
3) "lanes"
4) "0,1,2,3"
5) "speed"
6) "100000"
7) "index"
8) "1"
9) "admin_status"
10) "up"
11) "fec"
12) "rs"
13) "autoneg"
14) "0"
15) "mtu"
16) "9100"
17) "description"
18) ""
19) "oper_status"
20) "up"
```
Also its way to fix `show interface status`, `FEC` field but also need add `FEC` field to `hwsku.json`.
Before:
```
admin@sonic:~$ show interfaces status
Interface Lanes Speed MTU FEC Alias Vlan Oper Admin Type Asym PFC
----------- --------------- ------- ----- ----- ----------- ------ ------ ------- --------------- ----------
Ethernet0 0,1,2,3 100G 9100 N/A Ethernet0 routed up up QSFP28 or later N/A
```
After:
```
admin@sonic:~$ show interfaces status
Interface Lanes Speed MTU FEC Alias Vlan Oper Admin Type Asym PFC
----------- --------------- ------- ----- ----- ----------- ------ ------ ------- --------------- ----------
Ethernet0 0,1,2,3 100G 9100 rs Ethernet0 routed up up QSFP28 or later N/A
```
**- Why I did it**
Prior to SONiC using Debian Buster, we needed to build Python 3.5 or newer from source for installation in the SNMP container, becuase it wasn't available from the Debian repository for Jessie or Stretch. Now that all containers are based on Buster, we simply install Python 3.7 from the Debian repository in the host as well as all containers. We are no longer building Python 3 from source, so the Makefile is unused and we no longer need to install build dependencies in the slave containers.
**- How I did it**
- Remove Python 3 makefile
- No longer install Python 3 build dependencies in the slave containers.
Submodule changes to be committed:
* src/sonic-platform-daemons 81318f7...e72f6cd (3):
> [ledd] Minor refactor; add unit tests (#143)
> [thermalctld] Report unit test coverage (#141)
> [psud] Increase unit test coverage (#140)
Fixes#6445
Because the ipmihelper.py script in the 9332 folder is slightly different than the common one (due to LGTM fixes), when the common one gets copied during build time it causes the workspace/build to become dirty.
Signed-off-by: Danny Allen <daall@microsoft.com>
**- Why I did it**
Ledd is the last daemon that is not enabled to run in python3.
Even though there is a plan to deprecate this daemon and to replace it by something else it's one simple step toward python2 deprecation.
**- How I did it**
Changed the `command=` line for `ledd` in the `supervisord` configuration of `pmon`.
Copied what was done for other daemons.
**- How to verify it**
Booting a product that has a `led_control.py` should now show the ledd running in python3.
I ran `python3 -m pylint` on all `led_control.py` plugin which means that most of them should be python3 compliant.
There is however still a risk that some might not work.
Meet the requirement for the MUX_CABLE table that IPv6 loopbacks have a /128 prefix
Note that this change only affects the MUX_CABLE table, all other tables continue to use the loopback address provided in minigraph.
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
Changes in this update:
37695c8 [show]: Use TCP Connection For Muxcable Commands (#1371)
8119ba2 Validations checks while creating and deleting a Portchannel (#1326)
3df267e [config] Fix Breakout mode option and BREAKOUT_CFG table check method (#1270)
9bd709b [show] Fix show arp in case with FDB entries, linked to default VLAN (#1357)
bc2d27e [generate_dump]: fix syntax error
signed-of-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Currently FRR is send Prefix with VNI information to FPMSYNCD. This PR allows FRR to send RMAC with EVPN Type5 prefix to fpmsyncd. This is a temp fix. This patch will be removed once neighorch is ready to handle the Prefix and ARP (containing RMAC) separately.
[ci]: download artifacts from master branch (#768)
Do not create fabric port if mapping is not available (#769)
[syncd] Comparison logic log also current attr value on set operation (#763)
Add fabric port test to vslib (#737)
[ci]: use sonicbld pool (#766)
[tests] Remove exit command blocking all tests to run (#765)
[vslib]: adapt macsec sai 1.7.1 (#755)
Add support for SAI_SWITCH_ATTR_AVAILABLE_IPMC_ENTRY needed by CRM (#756)
Signed-off-by: Danny Allen <daall@microsoft.com>
Fix#5026
There is a race condition between zebra server accepts connections and bgpd tries to connect. Bgpd has a chance to try to connect before zebra is ready. In this scenario, bgpd will try again after 10 seconds and operate as normal within these 10 seconds. As a consequence, whatever bgpd tries to sent to zebra will be missing in the 10 seconds. To avoid such a scenario, bgpd should start after zebra is ready to accept connections.
Avoid sonic-cfggen crashing when a server does not have a configured loopback address in the minigraph
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
When building the sonic-slave-buster docker container, the node.js package is
installed to meet the requirements of the Azure DevOPs pipleline
build. Recently this install of node.js has been failing.
This commit fixes that build break by upgrading the
sonic-slave-buster build to install version 14.x of node.js which is the
current LTS version for buster.
**- Why I did it**
On the Mellanox platform, reboot cause is fetched from some certain sysfs which is created by the hw-management service. So determine-reboot-cause service shall start after hw-management, otherwise it could fail due to the related sysfs is not available yet.
**- How I did it**
Add a patch to the hw-management service to make sure determine-reboot-cause service should start after it.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
**- Why I did it**
- The thermalctld daemon on the Pmon docker requires support from the thermal manager API.
**- How I did it**
- Removed the old function for detecting a faulty fan.
- Removed the old function for detecting excess temperature.
- Implement thermal_manager APIs based on ThermalManagerBase
- Implement thermal_conditions APIs based on ThermalPolicyConditionBase
- Implement thermal_actions APIs based on ThermalPolicyActionBase
- Implement thermal_info APIs based on ThermalPolicyInfoBase
- Add thermal_policy.json
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
In order to build up device hierachy, PSU and module thermals are no longer child of chassis. PSU thermal belongs to PSU objects and SFP thermals belong to SFP object now. Need align this change in platform.json. Move thermal objects to correct parent device
* [warm boot finalizer] only wait for enabled components to reconcile
Define the component with its associated service. Only wait for components that have associated service enabled to reconcile during warm reboot.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
**- Why I did it**
Earlier today we found a bug in the SONiC TSA implementation.
TSC shows incorrect output (see below) in case we have a route-map which contains TSA route-map as a prefix.
```
admin@str-s6100-acs-1:~$ TSC
Traffic Shift Check:
System Mode: Not consistent
```
The reason is that TSC implementation has too loose regexps in TSA utilities, which match wrong route-map entries:
For example, current TSC matches following
```
route-map TO_BGP_PEER_V4 permit 200
route-map TO_BGP_PEER_V6 permit 200
```
But it should match only
```
route-map TO_BGP_PEER_V4 permit 20
route-map TO_BGP_PEER_V4 deny 30
route-map TO_BGP_PEER_V6 permit 20
route-map TO_BGP_PEER_V6 deny 30
```
**- How I did it**
I fixed it by using egrep with `^` and `$` regexp markers which match begin and end of the line.
**- How to verify it**
1. Add follwing entry to FRR config:
```
str-s6100-acs-1#
str-s6100-acs-1# conf t
str-s6100-acs-1(config)# route-map TO_BGP_PEER_V4 permit 200
str-s6100-acs-1(config-route-map)# end
```
2. Use the TSC command and check output. It should show normal.
```
admin@str-s6100-acs-1:~$ TSC
Traffic Shift Check:
System Mode: Normal```
**- Why I did it**
To enable running Pytest unit tests before building the Python 3 sonic-platform-common package
**- How I did it**
- Add Python 3 sonic-config-engine package as a dependency of Python 3 sonic-platform-common package (needed for both runtime and unit tests)
- No longer disable unit tests when building Python 3 sonic-platform-common package
The only Python code in the SwSS package, restore_neighbors.py, was recently converted to Python 3 and most dependencies were updated as part of #6207. However, the SwSS makefile still listed the Python 2 version of the swsscommon package as a dependency. This caused Python 2-related packages to be installed in containers unnecessarily.
Update sonic-linux-kernel pointer to pick up new commits:
- Backport patches to increase critical threshold for ASIC and validate transceiver temperature a7c1af7c44edde90dff49d672071139043bcdb65 548e8e0be4
- [ci]: Set up CI with Azure Pipelines 548e8e0be49692050ea4071d5e9945816bc5aacc a7c1af7c44
Signed-off-by: Kebo Liu <kebol@nvidia.com>
1. Fixes the missing DPKG file for gbsyncd-vs package
2. Fixes the softlink issue on the Platform-common and ztp package
3. Fixes the PYTHNON_DEBS list is missing for DBG dockers.
Fixed swi-tools code to work with `python3`
Updated the version of swi-tools downloaded by the `sonic-slave-buster/Dockerfile.j2`
Other Dockerfiles still use the `python2` version, though swi-tools is not used within the stretch builder.
