Why I did it
For trident4/tomahawk4, linux_ngknet.ko and linux_ngknetcb.ko have to be installed. Also, the kernel modules to load on such chips are different from existing ones, so we add an option is_ltsw_chip to determine the kernel modules to load. The option is_ltsw_chip is controlled by adding 'is_ltsw_chip=1' to platform_env.conf or not.
How to verify it
We verified that existing platforms still work after this change; and for platforms with trident4/tomahawk4, we can load the different kernel modules as expected after adding 'is_ltsw_chip=1' to platform_env.conf
b67d479 Fixed the sfp refactor issue
827c5a6 Added nokia_cmd command nokia_common grpc support for power down/up SFM module
aeb7f56 Added the nokia cli commands for midplane
c57d083 Fix the get_my_module issue and the thermal_infos exception issue.
0536293 Change the output of "show chassis module status"
63212d7 Enhance the help display for nokia_cmd command
e8d2599 Fix the sonic_install_ndk_service script issue
d52bdcf Add command nokia_cmd show sfm-eeprom support
Signed-off-by: mlok <marty.lok@nokia.com>
Why I did it
Support pddf to as4630/as7816/as7326
How I did it
Send needed file to the PR for these platform
How to verify it
Test sensors and show platform cmd.
root@as7326-56x-3:/home/admin# show platform psustatus
PSU Model Serial HW Rev Voltage (V) Current (A) Power (W) Status LED
PSU 1 FSF045-611 FSF0451912000505 N/A 12.06 5.50 66.00 OK green
PSU 2 FSF045-611 FSF0451912000568 N/A 12.00 5.50 66.00 OK green
root@as7326-56x-3:/home/admin# sensors
lm75-i2c-15-4a
Adapter: i2c-1-mux (chan_id 6)
Main Board Temperature: +35.5 C (high = +80.0 C, hyst = +75.0 C)
lm75-i2c-15-4b
Adapter: i2c-1-mux (chan_id 6)
CPU Board Temperature: +29.0 C (high = +80.0 C, hyst = +75.0 C)
fan_ctrl-i2c-11-66
Adapter: i2c-1-mux (chan_id 2)
fan1: 9100 RPM
fan2: 9400 RPM
fan3: 9300 RPM
fan4: 9600 RPM
fan5: 9000 RPM
fan6: 9100 RPM
fan7: 9100 RPM
fan8: 9300 RPM
fan9: 9200 RPM
fan10: 9400 RPM
fan11: 9200 RPM
fan12: 9400 RPM
pch_haswell-virtual-0
Adapter: Virtual device
temp1: +43.0 C
psu_pmbus-i2c-17-59
Adapter: i2c-1-mux (chan_id 0)
in3: +12.06 V
fan1: 6272 RPM
temp1: +37.0 C
power2: 60.00 W
curr2: +6.00 A
lm75-i2c-15-49
Adapter: i2c-1-mux (chan_id 6)
Main Board Temperature: +40.0 C (high = +80.0 C, hyst = +75.0 C)
lm75-i2c-15-48
Adapter: i2c-1-mux (chan_id 6)
Main Board Temperature: +39.0 C (high = +80.0 C, hyst = +75.0 C)
psu_pmbus-i2c-13-5b
Adapter: i2c-1-mux (chan_id 4)
in3: +12.00 V
fan1: 6144 RPM
temp1: +36.0 C
power2: 66.00 W
curr2: +5.50 A
coretemp-isa-0000
Adapter: ISA adapter
Package id 0: +50.0 C (high = +82.0 C, crit = +104.0 C)
Core 0: +50.0 C (high = +82.0 C, crit = +104.0 C)
Core 1: +50.0 C (high = +82.0 C, crit = +104.0 C)
Core 2: +50.0 C (high = +82.0 C, crit = +104.0 C)
Core 3: +50.0 C (high = +82.0 C, crit = +104.0 C)
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
DellEMC: N3248TE platform API2.0 changes
Why I did it
N3248TE Platform API 2.0 changes
How I did it
Implemented the functional API's needed for Platform API 2.0
Added system_health_monitoring_config.json file
How to verify it
Used the API 2.0 test suite to validate the test cases.
Co-authored-by: Arun LK <Arun_L_K@dell.com>
Why I did it
DellEMC : Added support for N3248TE/N3248PXE platforms
How I did it
Implemented the changes to enable/disable the watchdog support
How to verify it
watchdog_unit_test.txt
Co-authored-by: Arun LK <Arun_L_K@dell.com>
Why I did it
Support for show platform temp/fan for psu-temp and fan.
Original code doesn't has fan_drawer to support these information.
How I did it
Support for show platform temp/fan for psu-temp and fan.
Add fan_drawer.py and update thermal.py to add needed code.
It need PDDF common code to support . (Refer to #10213)
How to verify it
Test show platform temp and show platform fan.
root@as7726-32x-2:~# show platform fan
Drawer LED FAN Speed Direction Presence Status Timestamp
Fantray1 green Fantray1_1 38% EXHAUST Present OK 20220311 08:13:04
Fantray1 green Fantray1_2 38% EXHAUST Present OK 20220311 08:13:04
Fantray2 green Fantray2_1 38% EXHAUST Present OK 20220311 08:13:04
Fantray2 green Fantray2_2 38% EXHAUST Present OK 20220311 08:13:04
Fantray3 green Fantray3_1 38% EXHAUST Present OK 20220311 08:13:04
Fantray3 green Fantray3_2 38% EXHAUST Present OK 20220311 08:13:04
Fantray4 green Fantray4_1 38% EXHAUST Present OK 20220311 08:13:04
Fantray4 green Fantray4_2 38% EXHAUST Present OK 20220311 08:13:04
Fantray5 green Fantray5_1 38% EXHAUST Present OK 20220311 08:13:04
Fantray5 green Fantray5_2 38% EXHAUST Present OK 20220311 08:13:04
Fantray6 green Fantray6_1 38% EXHAUST Present OK 20220311 08:13:04
Fantray6 green Fantray6_2 38% EXHAUST Present OK 20220311 08:13:04
N/A green PSU1_FAN1 23% EXHAUST Present OK 20220311 08:13:04
N/A green PSU2_FAN1 22% EXHAUST Present OK 20220311 08:13:04
root@as7726-32x-2:~# show platform temp
Sensor Temperature High TH Low TH Crit High TH Crit Low TH Warning Timestamp
PSU1_TEMP1 28 N/A N/A N/A N/A False 20220311 08:13:04
PSU2_TEMP1 25 N/A N/A N/A N/A False 20220311 08:13:04
TEMP1 23.5 80.0 N/A N/A N/A False 20220311 08:13:04
TEMP2 27 80.0 N/A N/A N/A False 20220311 08:13:04
TEMP3 24 80.0 N/A N/A N/A False 20220311 08:13:04
TEMP4 27 80.0 N/A N/A N/A False 20220311 08:13:04
TEMP5 24 80.0 N/A N/A N/A False 20220311 08:13:04
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Why I did it
To reduce the processing time of rc.local, refactoring s6100 platform initialization.
Porting changes from 202012 branch [202012] Refactoring DELL platform init to reduce rc.local processing time #10171
- Fix i2c bus on crow cpu
- Fix exception handling in logs
- Improve linecard mgmt interface configuration
- Add new PSU models for chassis
- Misc fixes
* Initial pass of EdgeCore platform changes.
* Remove libevent dependency from lldpd.
* Remove python2 dependencies python3.7 force from platform install script.
* Include usbmount support changes.
* Add missing 4630 install file.
* Update a few file permissions. Add umask line to Makefile. Specify python3.9 in install script.
* Misc platform updates:
- Add missing fan drawer component to sonic_platform
- Remove kernel version specification from Makefile
- Update to 4630 utility
* - Fix file permissions on source files
- Fix compile issue with 4630 driver modules (set_fs, get_fs, no longer supported in kernel 5.10)
* Fix missing/extra parens in 4630 util script.
* Fix indentation in fanutil.py.
* Integrate deltas from Edgecore to ec_platform branch.
* Installer update from Edgecore to resolve smbus serial console errors.
* Update stable_size for warm boot.
* Fix SFP dictionary key to match xcvrd.
* - Add missing define in event.py files needed for xcvrd
- Fix SFP info dict key for 7xxx switches
* 5835 platform file updates including installer and 5835 utility.
* 5835 fix for DMAR errors on serial console.
* Don't skip starting thermalctld in the pmon container.
* Revert several changes that were not related to platform.
* Run thermalctld in pmon container.
* Don't disable thermalctld in the pmon container.
* Fix prints/parens in 7816 install utility.
* - Incorporate 7816 changes from Edgecore
- Fix 7326 driver file using old kernel function
* Update kernel modules to use kernel_read().
* Fix compile errors with 7816 and 7326 driver modules.
* Fix some indents preventing platform files from loading.
* Update 7816 platform sfp dictionary to match field names in xcvrd.
* Add missing service and util files for 7816.
* Update file names, etc. based on full SKU for 7816.
* Delete pddf files not needed. These were causing conflicts with API2.0
implementation.
* Remove pddf files suggested by Edgecore that were preventing API2.0 support from starting.
* Install API2.0 file instead of pddf.
* Update 7326 mac service file to not use pddf. Fix syntax errors in 7326 utility script.
* Fix sonic_platform setup file for 7326.
* Fix syntax errors in python scripts.
* Updates to 7326 platform files.
* Fix some tab errors pulled down from master merge.
* Remove pddf files that were added from previous merge.
* Updates for 5835.
* Fix missing command byte for 5835 psu status.
* Fix permission bits on 4630 service files.
* Update platforms to use new SFP refactoring.
* Fix unused var warnings.
Correct libsaithrift dependency package name from
LIBTHRIFT_DEV_0_14_1 THRIFT_COMPILER_0_14_1 to
LIBTHRIFT_0_14_1_DEV THRIFT_0_14_1_COMPILER
How I did it
How to verify it
Test Done:
make BLDENV=buster SAITHRIFT_V2=y -f Makefile.work target/debs/buster/saiserverv2_0.9.4_amd64.deb
Why I did it
N3248TE - Platform API 2.0 changes
How I did it
Implemented the functional API's needed for Platform API 2.0
How to verify it
Used the API 2.0 test suite to validate the test cases.
Signed-off-by: Jostar Yang jostar_yang@accton.com.tw
Why I did it
Fix led drv because CPLD SPEC is updated.
Fix i2c bus order
How I did it
Fix led drv. Set blacklist to i801 and ismt. Let accton util to modprobe i801 and ismt.
How to verify it
Test led and sensors cmd. Results are fine.
Why I did it
To fix I2C bus order to meet with HW SPEC. Let i801 use bus-0 and ismt use bus-1
How I did it
Modprobe i801 and then do ismt. So i801 will use bus-0 and ismt will use bus-1.
How to verify it
Test show cmd and sensors work well
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
AS7816 support AT or non-AT DUT. They use different pmbus i2c bus. So use "pre_pddf_init.sh" to check this case.
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
Fixes#10020
Why I did it
The platform api for parsing syseeprom information read from STATE DB has issue
with parsing the value part that has whitespace in the middle. The current
code assumes that the value part does not have whitespace. So everything after
the whitespace will be ignored. The syseeprom values returned from platform
API do not match the output of "show platform syseeprom".
How I did it
This change improved the regular expression for parsing syseeprom values to
accommodate whitespaces in the value.
How to verify it
Locally updated the code on a dx010 device. Call the platform API:
```
>>> import sonic_platform
>>> platform = sonic_platform.platform.Platform()
>>> chassis = platform.get_chassis()
>>> chassis.get_system_eeprom_info()
{'0x21': 'DX010', '0x22': 'R0872-F0020-02', '0x23': 'DX010B2F030A27BY200002', '0x24': '00:E0:EC:E7:71:0F', '0x25': '11/03/2020 21:22:56', '0x26': '3', '0x27': 'Seastone', '0x28': 'RANGELEY', '0x29': '2014.08', '0x2A': '131', '0x2B': 'CELESTICA', '0x2C': 'THA', '0x2D': 'Celestica', '0x2E': '1.0.5', '0x2F': 'LB', '0xFD': '', '0xFE': '0xAAB39BDB'}
```
Signed-off-by: Xin Wang <xiwang5@microsoft.com>
Generate the sai.profile base on the brcm j2 file if the sai.profile
is not existing in the dut mounted folder.
Change the supervisor service configuration accordingly.
Testing done:
Add the script and config in dut
saiservice server can start automatically with [systemctl start saiserver]
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
#### Why I did it
To bump the Thrift version to 0.14.1
- To avoid [CVE-2020-13949](https://nvd.nist.gov/vuln/detail/CVE-2020-13949)
- to fix some dependencies issues
#### How I did it
- rename `src/thrfit_0_13_0` to `src/thrift_2` to remove version number in the path. (`src/thrift` contains rules to build thrift 0.11.0 )
- Add thrift sources as submodule as there are no prepared debian packages for version >0.13.0 on [debian.org](https://packages.debian.org/search?searchon=sourcenames&keywords=thrift)
- Added patches with fixes for original thrift debian rules:(remove unneeded packages, fix multi job build)
#### How to verify it
```
BLDENV=buster make -f Makefile.work target/debs/buster/libthrift-dev_0.14.1_amd64.deb
```
ded0344 Return both 'vendor_rev' and 'hardware_rev' keys from get_transceiver_info to support both earlier and later versions of xcvrd
b3442cc Change log_error to log_info when transceiver module is transitioned
3d3a73c Fix problem introduced with new SFP caching paradigm
2915746 Add script to reboot all IMMs
17ad221 Fix the position_in_parent for the psu entity
207e731 No longer force read pages at SFP init time
b387921 Fixed the voltage and power with rounding to 2 digit decimals
Signed-off-by: mlok <marty.lok@nokia.com>
* [AS4630-54PE] Add to support PDDF
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
* Fix LGTM alerts
* Fix LGTM alerts
* Fix LGTM alerts
* Add post_device.sh to turn off stk led
* Add to support system_health
* Correct the wait and timeout mechanism for better CPU usage
* Add event.c to support port evt change
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Support saiserver v2 with python3 and thrift 0.13.0
add variables to support the saiserverv2
build different thrift in saithrift depends on saiserver version
build differernt versions of saiserver
make the saiserver and saiserver docker with version number
test done:
build two different versions of sasiserver in local build environment
add saiserver to buster
Co-authored-by: richard.yu <richard.yu@microsoft.comwq>
* [AS7726-32X] Add to support mulit PSU in PDDF
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
* Modify SN offset and include path
* Fix device_name to PSU2-EEPROM in PSU2
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Why I did it
Old fan drv will be build fail under kernel 5.10. It get below error message.
/sonic/platform/broadcom/sonic-platform-modules-accton/as7312-54xs/modules/accton_as7312_54x_fan.c:483:5: error: implicit declarat ion of function 'set_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
set_fs(KERNEL_DS);
^~~~~~
sget_fc
How I did it
These code is old design and they are not needed currently. So remove them.
Signed-off-by: Jostar Yang <jostar_yang@accton.com>
Why I did it
Update Broadcom SAI to version 6.0.0.13, SDK 6.5.24, saibcm-modules to 6.5.24.gpl
How I did it
Brcm SAI 6.0 EA with fixes for CS00012203367, CS00012219613, CS00012213974, CS00012218290, CS00012217169, CS00012211718, CS00012213944, CS00012215529, CS00012218100, CS00012214196, CS00012212681, CS00012205138, CS00012208537, CS00012185316, CS00012208524, CS00012203367, CS00012197364.
* Add intel_iommu=off to installer.conf
* This solve flooding DMAR err msg: "handling fault status reg 2"
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* remove customized at24 driver
* Use kernel 5.10.46 upstream at24 driver directly. The ADDR16 issue on
old driver has gone.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* pin I2C-0/I2C-1 bus order
* otherwise, sometimes I2C-0/I2C-1 will be assigned to the undesired one.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* fix i2c bus num for fan driver
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* backward compatible with R0A/R0B HW
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* fix workdir for seastone2
Signed-off-by: Viktor Ekmark <viktor@ekmark.se>
* seastone2: Add I2C SFP definition for SFP1
Signed-off-by: Christian Svensson <blue@cmd.nu>
* [device/cel_seastone_2] sfputil logic for SFP1
Earlier logic resulted in the name of SFP1 being SFP33 which is not
correct. The cannonical source is seastone2_fpga module and it calls it
SFP1, so ensure the logic does as well.
Signed-off-by: Christian Svensson <blue@cmd.nu>
* [device/cel_seastone_2] sysfs paths for SFP1
Various changes that plumbs the correct port presence and DOM decoding
for the SFP1 port.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Co-authored-by: Christian Svensson <blue@cmd.nu>
Enable pca954x idle_disconnect to avoid possible I2C device address conflict.
How I did it
Change pca954x device_attr idle_state to -2 (MUX_IDLE_DISCONNECT).
How to verify it
Cat pca954x device_attr idle_state and confirm the value is -2.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
Why I did it
Reboot cause is not working in S52xx platforms.
How I did it
Modified platform API's.
How to verify it
Check "show reboot-cause" to verify the reboot reason
Why I did it
To incorporate the below changes in DellEMC S6100, S6000 platforms.
S6100, S6000:
Implement 'get_revision' method for Chassis
Implement 'get_maximum_consumed_power' method for FanDrawer
Implement 'get_revision', 'get_maximum_supplied_power' methods for PSU
Implement 'get_error_description' method for SFP.
S6100:
Implement 'get_module_index' method for Chassis
Implement 'get_description', 'get_maximum_consumed_power', 'get_oper_status', 'get_slot' methods for Module
Update component names in platform.json
How I did it
Implement the platform API methods in the respective device files
How to verify it
Verified that the respective sonic-mgmt platform API test cases report success.
Update Nokia platform sonic-pmon submoduel to the latest with the following commits
c41c823 Fix transceiver module dynamic insertion/removal operations
21a1df6 Fixed pcied process FATAl issue
7fc1fd4 Fix midplane status nokia_cmd
a14ee1c Override get_module() api in chassis
8a457fc SON-326: Watchdog logger changes and file scrubbing
7250eb1 SON-410: Fix missing eeprom access routine
7a70c42 Allow only reboot of self card for OC API test
6ab5d96 Fixed the flake8 compliant issues
807de95 APIs to set thermal threshold to return false
9b38265 SON-382: platform-dump with common techsupport
3f83a67 Add model, base_mac, system_eeprom and serial number support in moduel.py
848d311 SFP: Add get_error_description and fix return status for set_lpmode
1fcb5de PSU check presence of psu instance for APIs
7c68da3 Fixed the eagle and hornet card description
0c01d07 Module support for reboot API
- Use SfpOptoeBase by default to leverage new `sonic_xcvr` refactor
- Add support for `Woodleaf` product
- Move `libsfp-eeprom.so` to a different `.deb` package
- Add new logrotate configuration for arista logs
- Improve logging mechanism for the drivers (IO loglevel, fix syslog duplicates)
- Initialize chassis cards in parallel
- Refactor of `get_change_event` to fix interrupts treated as presence change
Why I did it
To implement fan control using thermalctld in DellEMC S6000 platform
Requires: Azure/sonic-linux-kernel#241
How I did it
Add thermal policies in 'thermal_policy.json'
Implemented thermal_manager.py and the necessary modules to perform fan control via thermalctld
Removed fancontrol.sh
How to verify it
Verified that the fan speeds are set based on the fan and temperature status.
Logs: S6000_fan_control_test_logs.txt
Why I did it
Adding SSD as part of platform components list.
Introducing platform_fw_au_reboot_handle to use auto-update functionality in fwutil
How I did it
Changes to be committed:
(use "git restore --staged <file>..." to unstage)
modified: platform/broadcom/sonic-platform-modules-dell/debian/platform-modules-s6100.install
new file: platform/broadcom/sonic-platform-modules-dell/s6100/scripts/platform_fw_au_reboot_handle
modified: platform/broadcom/sonic-platform-modules-dell/s6100/sonic_platform/chassis.py
modified: platform/broadcom/sonic-platform-modules-dell/s6100/sonic_platform/component.py
How to verify it
By running fwutil command.
Warning: fwupdate_fwimage_dir: /var/platform/fwpackage/.
Chassis Module Component Firmware Version (Current/Available) Status
--------- -------- ----------- ------------------------------- ----------------------------- ------------------
S6100-ON BIOS S6100-BIOS-3.25.0.2-9-noRP2.bin 3.25.0.2-8 / 3.25.0.2-9 update is required
FPGA smf_firmware_upgrade.tar 2.4 / 2.4 up-to-date
CPLD cpld_firmware_upgrade.tar 4 / 4 up-to-date
SSD ssd_firmware_upgrade.tar S16425cG / S16425cG up-to-date
root@sonic:~#
Why I did it
To support iTCO watchdog using watchdog APIs.
How I did it
Implemented a new watchdog class WatchdogTCO for interfacing with iTCO watchdog.
Updated reboot cause determination logic.
How to verify it
Verified that the watchdog APIs' return values are as expected.
Logs: UT_logs.txt
For broadcom sai, we only need to upgrade the version, not necessary the token part in the url.
Co-authored-by: Ubuntu <xumia@xumia-vm1.jqzc3g5pdlluxln0vevsg3s20h.xx.internal.cloudapp.net>
- add `set_write_max` and `get_write_max` apis to Sfp API
- add `get_revision` platform API
- implement `is_midplane_reacheable` API
- add software fallback for setting Xcvr low power mode
- add `get_error_description` API
- add support for Woodleaf SKU
- various fixes/refactors/cleanups
Signed-off-by: pettershao-ragilenetworks pettershao@ragilenetworks.com
What I did it
Add new platform x86_64-ragile_ra-b6510-32c-r0 (Trident 3)
ASIC Vendor: Broadcom
Switch ASIC: Trident 3
Port Config: 32x100G
Add new platform x86_64-ragile_ra-b6920-4s-r0 (Tomahawk 3)
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk 3
Port Config: 128x100G
-How I did it
Provide device and platform related files.
-How to verify it
show platform fan
show platform ssdhealth
show platform psustatus
show platform summary
show platform syseeprom
show platform temperature
show interface status
Remove the "4.19..." specific code to add "-unsigned" suffix and just do so for any linux version.
For the syseeprom API part, have the Arista syseeprom class inherit from a class that can populate db.
Co-authored-by: Zhi Yuan (Carl) Zhao <zyzhao@arista.com>
Why I did it
To include capabilities fields in platform.json of DellEMC S6000, S6100, Z9332f platforms.
How I did it
Add the capabilities fields in each platform's respective platform.json.
How to verify it
Ran sonic-mgmt platform api test cases that use capabilities fields and verified that the results are as expected.
BRCM SAI missed implementing the SAI API "sai_query_stats_capability()" which is causing build issue.
The build issue is impacting PR(s) that need to use this API.
This PR is to stubbed BRCM SAI to add this SAI API and return not implemented so that it will fix build issue that it is causing.
No other functional changes were made.
ipmihelper files are repeated for few DellEMC platforms. Removed the
files in sonic_platform since as part of debian rules,ipmihelper will be
copied to necessary directory.
Also add out of tree pca9548 mux driver to use platform data to mapping i2c bus with front panel port.
Signed-off-by: Jakkapan Jangmuang <jjangmua@celestica.com>
Co-authored-by: Saikrishna Arcot <sarcot@microsoft.com>
Add an include in saibcm-modules and saibcm-modules-dnx that are now
needed due to Mellanox kernel patches.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
The kernel already provides psample, and with module versioning being
done in modpost, having the SDK compile its own copy of psample breaks
loading dependent modules.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Update the build rules in saibcm-modules to use the 5.10 kernel instead
of searching for the 4.19 kernel. In addition, some code changes were
done to get it to compile. The main categories of such changes are as
follows:
* For /proc files, `struct file_operations` has been replaced with
`struct proc_ops`.
* Y2038 changes to use the new APIs, since `do_gettimeofday()` is no
longer available.
* Minor changes in how external kernel module symbols are read by
modpost.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
- Why I did it
In case an app.ext requires a dependency syncd^1.0.0, the RPC version of syncd will not satisfy this constraint, since 1.0.0-rpc < 1.0.0. This is not correct to put 'rpc' as a prerelease identifier. Instead put 'rpc' as build metadata in the version: 1.0.0+rpc which satisfies the constraint ^1.0.0.
- How I did it
Changed the way how to version in RPC and DBG images are constructed.
- How to verify it
Install app.ext with syncd^1.0.0 dependency on a switch with RPC syncd docker.
Signed-off-by: Stepan Blyshchak <stepanb@nvidia.com>
Why I did it
Added Support for Dell EMC S5212f platform
How I did it
Implemented the support for Dell EMC S5212f platform
Platform: x86_64-dellemc_s5212f_c3538-r0
HwSKU: DellEMC-S5212f-P-25G
ASIC: broadcom
ASIC Count: 1
How to verify it
Verified the show command outputs
Why I did it
Added Support for Alphanetworks SNJ60D0-320F platform
How I did it
Implemented the support for Alphanetworks SNJ60D0-320F platform
Platform: x86_64-alphanetworks_snj60d0_320f-r0
HwSKU: Alphanetworks-SNJ60D0-320F
ASIC: broadcom
ASIC Count: 1
How to verify it
Verified the show command outputs
Why I did it
PCIe Gen1 settings was needed for Dell S6000 device.
How I did it
Modified from Gen2 to Gen 1 speed for Dell S6000 PCIe devices
How to verify it
Check lspci output, verify the syslogs
Why I did it
Added support for the device S5224F
How I did it
Implemented the support for the platform S5224F
Switch Vendor: DellEMC
Switch SKU: S5224F-ON
ASIC Vendor: Broadcom
SONiC Image: sonic-broadcom.bin
How to verify it
Verified the show platform/interface commands
Why I did it
Added support for the device N3248PXE
How I did it
Implemented the support for the platform N3248PXE
n3248pxe_unit_test_log.txt
Switch Vendor: DellEMC
* Switch SKU: N3248PXE
* ASIC Vendor: Broadcom
* SONiC Image: sonic-broadcom.bin
How to verify it
Verified the show platform commands
Why I did it
Added support for the device N3248TE
How I did it
Implemented the support for the platform N3248TE
Switch Vendor: DellEMC
Switch SKU: N3248TE
ASIC Vendor: Broadcom
SONiC Image: sonic-broadcom.bin
How to verify it
Verified the show platform commands
What I did it
Add new platform x86_64-ragile_ra-b6910-64c-r0 (Tomahawk 3)
ASIC Vendor: Broadcom
Switch ASIC: Tomahawk 3
Port Config: 64x100G
-How I did it
Provide device and platform related files.
-How to verify it
show platform fan
show platform ssdhealth
show platform psustatus
show platform summary
show platform syseeprom
show platform temperature
show interface status
Why I did it
Power cycle test case fails for Z9332f in sonic-mgmt framework(#8605).
How I did it
Modified the platform API to return expected strings.
How to verify it
Power cycle the device and verify the reboot reason.
Run sonic-mgmt test_reboot script.
Catch up on fixes from BRCM SUG repo to pick up fixes after 5.0.0.6 all the way up to 5.0.0.8
Fixes include the following:
```
CS00012201827: Warmreboot causes syncd crash with SAI_API_UNSPECIFIED:syncdb_data_file_read:2230 Failed to parse JSON: error -2
DNX: Fix for ACL table create with v6 next hdr attr
and many unspecified changes that also went into 5.0.0.8
```
#### How to verify it
Preliminary tests looks fine on both XGS (gechiang) and DNX (judyjoseph)
On XGS testing done as following:
BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on 7260CX3 T0 DUT and all passed:
```
ipfwd/test_dir_bcast.py
fdb/test_fdb.py
fib/test_fib.py
vlan/test_valn.py
```
Also validated for for CS00012201827 (https://github.com/Azure/sonic-buildimage/issues/8300)
To enable saiserver docker on different platforms, it needs different configuration files. make the saiserver docker mount them in hwsku folder.
Co-authored-by: Ubuntu <richardyu@richardyu-ubuntu-vm0.trsxrdzozv2e1czsze2t05vqzh.ix.internal.cloudapp.net>
- Disable health monitoring of `psu.voltage` until support is implemented
- chassis: disable provisioning bit once linecard has booted
- chassis: fix issue in `show version` when running as `admin`
- chassis: fix race when reading an eeprom before it's available
- chassis: implement `get_all_asics` call
- api: fix `ChassisBase.get_system_eeprom_info` implementation
- api: add missing thermal condition and info
- api: fix return value of `ChassisBase.set_status_led`
- sfp: introduce SfpOptoeBase implementation used based on configuration knob
- psu: rely on pmbus to read input/output status when other mechanism is missing
- misc: other refactors and improvements
Why I did it
To monitor the SSD health condition in DellEMC S6100 platform post upgrade.
A daemon is introduced to monitor the SSD every one hour.
To check for SSD status at boot time and at the time of cold-reboot.
All these changes are supported only for newer SSD firmware.
Porting changes from 201911 branch
Added a platform_reboot_pre_check script to prevent cold-reboot based on SSD status.
Depends on Azure/sonic-utilities#1556
DO NOT MERGE UNTIL ABOVE PR IS MERGED
CPLD offset in led drv is incorrect.
#### How to verify it
echo 1 > brightness, show green on in DIAG led
echo 3 > brightness, show red on in DIAG led
echo 4 > brightness, show blue on in DIAG led
echo 5 > brightness, show green blinking in DIAG led
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
Why I did it
Support Nokia ixr7250E IMM and Supervisor cards
How I did it
Added modules x86_64-nokia_ixr7250e_sup-r0 and x86_64-nokia_ixr7250e_36x400g-r0 ../device/nokia directory.
Modified the platform/broadcom/one-image.mk to include NOKIA_IXR7250_PLATFORM_MODULE
Modified the platform/broadcom/rule.mk to include the platform-module-nokia.mk
