- Why I did it
Update SAI version to SAIBuild2311.26.0.28
Fixed issues
1. Traffic with unicast destination ip and multicast destination mac wasn't properly dropped
2. When working with SAI_DEFAULT_SWITCHING_MODE_STORE_FORWARD key/value enabled, trying to add a LAG member to a LAG which is created after warm boot initial configuration phase ended, will fail.
3. Optional feature of Port IP counters (SAI_PORT_STAT_IP*) , enabled by SAI XML per-port-ip-counter-enabled config node, wasn't initialized properly.
4. Creating BFD session for non default VRF fails (SAI_BFD_SESSION_ATTR_VIRTUAL_ROUTER != SAI_SWITCH_ATTR_DEFAULT_VIRTUAL_ROUTER_ID).
5. The default value for port FEC during switch init for Spectrum3 was initialized as 'auto' and not aligned to SAI header default 'none'. Note if setups has invalid configuration and relied previously on auto, now it might be necessary for the user to provide explicit valid value for SAI_PORT_ATTR_FEC_MODE
Update SDK/FW version to 4.6.2134/2012.2134
Fixed issues:
1. Updated SN3700C to enable limit to 100G speed.
2. Recovering from Low power mode might ends with port down.
- How I did it
Updating the versions in makefile
- How to verify it
Confirm issues fixed and run sonic-mgmt tests
Why I did it
Update SDK/SAI and FW for Mellanox Platform
How I did it
Update SDK/FW to v4.6.2104/v2012.2104
Fixed Issues:
Some of the Warmboot related files which were created by SDK during switch create are now generated during pre shutdown flow
New Features:
Debian 12 and kernel 6.1 support
Update SAI
New Features:
Auto Fec Support
FDB entries are now restored after warmboot to prevent temporary system flooding.
Minor Enhancement and Bug Fix in integrate-mlnx-sdk
How to verify it
Build Image and run tests
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
[Nvidia] Enable iproute2 & fix mft build (#16)
* Enable iproute2 as the SDK is also built
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
* [Nvidia] Dont use mkbmdeb method of dkms to build the package
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
* Added linux image to the Depends section of mft
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
[Nvidia] [Bookworm] Separate KERNEL_MFT into a new target (#16782)
* [Nvidia] Seperate KERNEL_MFT into a new target because of kernel header dependency
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
* Update linux-kernel submodule
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
* Fix paralell build problem
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
---------
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
- Why I did it
SAI bug Fixes
1. When creating an ACL rule with SAI_ACL_ENTRY_ATTR_FIELD_SRC_IP/SAI_ACL_ENTRY_ATTR_FIELD_DST_IP enabled, and then disabling the field by setting enable=false, a match on L3_type=IPv4 will remain programmed for the rule Issue resolved after the fix
2. Allow the max scale of virtual routers to be configure for SPC-1, SPC-2, SPC-3 which is 255 when fastboot enable and 511 when fastboot disable
3. Remove default hash key of SRC_MAC, DST_MAC and ETH_TYPE
SAI features
1. Port init profile
2. Dual ToR Active-Standby | Additional MAC support
SDK/FW bug fixes
1. When preforming fast boot from an old SDK version (currently installed) to a newer one (target version), and the system was initially loaded with a new SDK version (past version), and the system has not been wiped, under specific conditions, the fast boot would use the past version's data and may fail.
- How I did it
Update SAI version to SAIBuild2211.25.1.4
Update SDK/FW version to 4.6.1062/2012.1062
SONiC changes:
1. Support Spectrum4 ASIC FW binary building.
2. Support new SDK sx-obj-desc lib building since new SAI need it.
3. Remove SX_SCEW debian package from Mellanox SDK build since we are no longer using it (we use libxml2 instead).
4. Update SAI, SDK, FW to version 4.6.1020/2012.1020/SAIBuild2305.25.0.3
SDK/FW bug fixes
1. In SPC-1 platforms: Fastboot mode is not operational for Split port with Force mode in 50G speed
SFP modules are kept in disabled state after set LPM (low power mode) on/off for at least 3 minutes.
2. When preforming fast boot from an old SDK version (currently installed) to a newer one (target version), and the system was initially loaded with a new SDK version (past version), and the system has not been wiped, under specific conditions, the fast boot would use the past version's data and may fail.
SDK/FW Features
1. On SN2700 all ports can support y cable by credo
SAI bug Fixes
1. When creating an ACL rule with SAI_ACL_ENTRY_ATTR_FIELD_SRC_IP/SAI_ACL_ENTRY_ATTR_FIELD_DST_IP enabled, and then disabling the field by setting enable=false, a match on L3_type=IPv4 will remain programmed for the rule Issue resolved after the fix
2. Allow the max scale of virtual routers to be configure for SPC-1, SPC-2, SPC-3 when fastboot enable
3. Remove default hash key of SRC_MAC, DST_MAC and ETH_TYPE
SAI features
1. Port init profile
- How I did it
Update SDK/FW/SAI make files
- How to verify it
Run full sonic-mgmt regression on Mellanox platform
Signed-off-by: Kebo Liu <kebol@nvidia.com>
= Why I did it
To optimize Mellanox platform SAI build
- How I did it
SAI debs are now downloaded as Spectrum-SDK-Drivers-SONiC-Bins release.
- How to verify it
Configure/build for Mellanox platform, check the image and ensure that correct SAI debs are included.
Why I did it
Align with SAI headers v1.12.0
Work item tracking
Microsoft ADO (number only):
How I did it
Update Mellanox SAI submodule
How to verify it
Compile SONiC image
SDK/FW Fixed Issues:
• When a system has more than 256 ACL entries, on rare occasion, removing/adding entries may cause some ACL entries not to work.
• When using mirror session policer on spectrum-2, spectrum-3, the actual CIR was 1.28 times more than the configured CIR value
• After warm boot process, when enabling ECN marking and the port is in split mode, traffic sent to the port under congestion (for example, when connecting two ports with a total speed of 50GbE to a single 25GbE port) is not marked.
• Warm boot might fail if the key value SAI_KEY_ACCUMULATED_FLOW_COUNTER_UNITS_IN_KB is set
• If counters are bound to an next hop group, there is a probability the next API calls that modify the next-hop group members will fail.
• In Spectrum platforms Fastboot mode is not operational for Split port with Force mode in 50G speed
• When fine grain next hop group has a size of 2K or 4K members, and group is removed, FW will remove only (size % 2048) members, resulting in leakage of KVD resources
• When reading some port statistics, or bulk reading some Queue or PG statistics, and in parallel reading or writing other counters, FW may, in rare cases, get stuck
• SN2201 Module 1 is considered to be present/linked while no cable/module is plugged
• On Spectrum-3 when port configure to 400G FW might stuck after running mlxlink while 400G interface connected and swap between upper and lower 4 lanes
SAI New features:
• ACL: Added support for an ACL match on the AETH field (SAI_ACL_TABLE_ATTR_FIELD_AETH_SYNDROME, SAI_ACL_ENTRY_ATTR_FIELD_AETH_SYNDROME) to count RoCE NAK and CNP packets.
• PLL Status: Added a new logging entry that alerts the user upon a PLL lock loss event.
• Dual ToR - Additional MAC Address: Added support for setting a MAC address for the router interface which is not part of the 10 bit MAC address available for RIFs on Spectrum-1, as part of the Dual ToR scenario.
• Dual ToR: DSCP Remapping Added support for tunnel QoS maps as part of the Dual TOR scenario.
SAI Fixed issues:
• When setting a WRED profile attribute for a color that was not enabled during the profile create time, an error would be returned. After the fix, a default profile is create on such scenario and the set attribute is applied on top of it
• When calling the flush FDB by using the SAI_FDB_FLUSH_ATTR_BRIDGE_PORT_ID attribute, the bridge bv_id value was filled on the notification callback where it should have been left empty.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- Why I did it
To include latest fixes and new functionality
SAI fixes and new features
fix#3205239, incorrect object type returned for SG child list
Fix VRF-VNI map entries remove issue
ECC health event and logging
[Port Buffers] restore default queue and pg configuration when all user pools are deleted
Fix EVPN type3 error on removal of uc/bc flood group
Fix EVPN type2 MAC move from local to remote results in SAI failure
Fix Disable learning on VXLAN tunnel
Fix error on VXLAN v6 tunnel removal
Fix port cannot apply schedule group when it is a lag member
Fix BFD add more detailed message on BFD packet not related to any existing session
gcc10 compilation fixes
Disable learning on VXLAN tunnel
Support BFD remote-disc exchange in negotiation stage
Tunnel Loopback packet action attribute implementation (for Dual TOR)
Add KVD resources MIN/MAX functionality (pending CRM issue with MIN only)
Support for CRC2 hash algorithm
Bulk counter support for PGs, queues
Support mirror sample rate attribute (SPC2+)
[Functional] [QoS] | Unable to remove SCHEDULE profile table even if there is no object referencing it
Next hop group optimized bulk API
Reduce verbosity of shared database already exists print
Span mirror policer (SPC2+), optimize pipeline for acl mirror action with policer on SPC2+
use same size descriptor pool for rx/tx
fix bfd - notify Sonic for admin-down event
2201 - empty list for supported fec for RJ45 ports
Fix don't disable used tunnel underlay interfaces
SDK fixes
100GbE FCI DAC (10137628-4050LF/HPE PN: 845408-B21) was recognized by mistake as supporting "cable burning' which caused the switch firmware to read page 0x9f (which unsupported in the cable) and to report this cable as having "bad eeprom".
Added remote peer UDP port information in BFD packet event.
After editing an ECMP, the resilient ECMP next-hop counter may not count correctly.
Fixed potential memory leaks in some APIs related to LPM
If TTL_CMD_COPY is used in Encap direction for a packet with no TTL, then the value passed in the ttl data structure will be used if non-zero (default 255 if zero).
In SN2201: When configuring Force mode, user should configure Speed and FEC on both sides
In Flex Tunnel encapsulation flow, if the encapsulation is with an IPv6 header, the flow label field may not be updated as expected.
In some cases, when changing speed to 400GbE over 8 lanes, the first few packets would be dropped.
In some traffic patterns involving small packets, the PortRcvErrors counter may mistakenly count events of local physical errors due to an internal flow in the hardware that involves link packets.
On Spectrum systems, sometimes during link failure, not all previous firmware indications cleared properly, potentially affecting the next link up attempt.
On the NVIDIA Spectrum-2 switch, when receiving a packet with Symbol Errors on ports that are configured to cut-thought mode, a pipeline might get stuck.
PCI calibration changes from a static to a dynamic mechanism.
SDK debug dump shows "Unknown" Counter in RFC3635 Counter Group.
SDK debug dump shows "Unknown" Counter in the PPCNT Traffic Class Counter Group.
SDK Dump missing column headers in some GC tables may result in difficulty understanding the dump.
SLL configuration is missing in SDK dump.
Spectrum-2 systems, do no support 1GbE on supported 40GbE modules.
When binding a UDP port which is already in use for BFD TX session, the error message appears incorrectly.
When Flex Tunnel was used, Flex Modifier sometimes experienced a brief mis-configuration during ISSU.
When many ports are active (e.g. 70 ports up), and the configuration of shared buffer is applied on the fly, occasionally, the firmware might get stuck.
When running 1GbE speeds on SN4600 system, the port remained active while peer side was closed.
When toggling many ports of the Spectrum devices while raising 10GbE link up and link maintenance is enabled, the switch may get stuck and may need to be rebooted.
When trying to reconfigure the Flex Parser header and Flex transition parameters after ISSU, the switch will returned an error even if the configuration was identical to that done before performing the ISSU.
While toggling the cable, and the low power mode is set to ON, an unexpected PMPE event error is received.
- How I did it
Updated SDK/SAI submodule and relevant makefiles with the required versions.
- How to verify it
Build an image and run tests from "sonic-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
- Why I did it
Add support for mellanox platform building for target architecture arm64.
- How I did it
Contains the following changes:
1. Change instances of hard-coded amd64 to $(CONFIGURED_ARCH)
2. Add logic to download correct binary for MFT package
3. Add TARGET_BOOTLOADER=grub definition to rules.mk to override default arm64 bootloader
- How to verify it
Build mellanox platform with TARGET_ARCH set as arm64
- Why I did it
Advance to new SAI version for bugs fixes as well as new features/enhacements:
New:
- ARM64 support
- FG ECMP performance optimization
- Support setting empty list for port ingress/egress buffer profile list
- Add service port for SN5600
- Add CR8/SR8/LR8/KR8 interface type
- Disable mlxtrace during debug dump
Fixes:
- Fix SAI_ACL_ENTRY_ATTR_FIELD_TC
- Fix Packets loop back if no member in portchannel
- Fix optimize descriptors apply time (and fast boot time)
- Add flush fdb entries for vxlan tunnel bridge port
- Don't disable used tunnel underlay interfaces
- How I did it
Advanced SAI submodule
- How to verify it
make configure PLATFORM=mellanox
make target/sonic-mellanox.bin
Signed-off-by: Nazarii Hnydyn <nazariig@nvidia.com>
Update SDK/FW to 4.5.1500/2010.1500 and SAI version to 1.21.1.1
SDK/FW features:
1. Added support for Finisar DR4 (FTCD4523E2PCM) on Spectrum-2 and Spectrum-3 systems.
SAI Features:
1. ECMP overlay support for IPv6
2. BFD offloading / 4K scale
3. Host interface user traps + improved trap registration (table entry)
4. gcc11 compilation fixes
5. Read support for ACL redirect action
6. Optimize ECMP DB size
7. Buffer descriptors new defaults
8. Updated port mapping for SN2201
SAI Fixes:
1. Debug counter removal when configured with all drop reasons
- Why I did it
Upgrade Mellanox SDK and SAI versions to latest
- How I did it
Updated submodule pointers
- How to verify it
Regression tested
- Why I did it
To include latest SDK fixes:
1. On CMIS modules, after low power configuration, the firmware waited for the module state to be ModuleReady instead of ModuleLowPower causing delays.
2. When connecting SN4600C, 100GbE port with CWDM4 module (Gen 3.0), link up time is 30 seconds.
and to include SAI fixes \ changes:
1. Reduce verbosity for resource check vendor data not found
2. Fix metadata validation, check default value on conditions check
3. Add 100MB, 10MB to 2201 system
4. L3 VXLAN overlay ECMP
5. VXLAN srcport API implementation
6. Fix scheduler profile null (default values) when set on sub group scheduler group
7. Fix ACL binding restoration when port leaves a LAG
8. Fix route logic for set next hop/action and reference counter for ECMP overlay
- How I did it
1. Updated SDK/FW submodule and relevant makefiles with the required versions.
2. Update SAI submodule and relevant makefile with the required version.
- How to verify it
Build an image and run tests from "sonic-mgmt".
- Why I did it
To include latest fixes.
SAI
1. Reclaim buffers for port which is admin down
2. Support for Spectrum-4 os Nvidia ASIC simulation
3. Support for SN2201
4. Fix host interface table entry, one channel per trap (fix sflow double registration)
5. 2 new queue counters - ecn marked packets + shared current occupancy
6. Fix storm policer unknown unicast
7. Add key/value for accuflow counters
8. Add MAC move
9. Add mirror congestion mode attribute
SDK
1. Under various circumstances, Ethernet ports falsely showed that InfiniBand cables were connected.
2. In SN4600C, at times, the link up time in both DAC and optics cables may, in the worst case, take up to 15 seconds.
3. Using SN4600C with copper or optics loopback cables in NRZ speeds, link may raise in long link up times
4. When ECMP has high amount of next-hops based on VLAN interfaces, in some rare cases, packets will get a wrong VLAN tag and will be dropped.
5. When connecting Spectrum devices with optical transceivers that support RXLOS, remote side port down might cause the switch firmware to get stuck and cause unexpected switch behavior.
6. Aggregation event is missing for WJH L2 drop reason 'Unicast egress port list is empty'.
7. Tying the SCL and SDA of the optical modules to 3.3V causes errors.
8. On SN4600, there was a delay of more than 10 seconds from the time a data packet is sent from CPU until it is transmitted through one of the switch ports.
9. While using SN4600C system with Finisar FTLC1157RGPL 100GbE CWDM4 modules, intermittent link flaps across multiple ports may be observed.
10. In Spectrum-2 and Spectrum-3 systems, link did not work in auto-negotiation when connected to Marvell PHY. KR mechanism has been enhanced to integrate with Marvell PHY.
11. The tunnel counter counts the drop packets now for Spectrum-2 and Spectrum-3 and consistent with Spectrum behavior and count the ECN dropped packets as well.
12. When connecting SN3800 to Cisco-9000, fast-linkup flow will fail and will rise in the normal flow.
13. Race condition in WJH library: when multiple threads load the LAG shared memory concurrently, the program may crash.
14. Add WJH L2 drop reason 'Unicast egress port list is empty' as a new drop reason.
15. Fixed a memory leak in sx_api_port_sflow_statistics_get API.
16. During initialization flow, the command interface that is used by the minimal driver and SDK caused the collision in the firmware since the same buffer is used in the firmware for the two interfaces.
17. Fix route issue on Kernel 5.10
- How I did it
Updated SDK/SAI submodule and relevant makefiles with the required versions.
- How to verify it
Build an image and run tests from "sonic-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
- Why I did it
Advance to new Nvidia SAI release with the following changes:
New features:
- Align with new SDK/FW version 4.5.1006 and above and in parallel to existing used SDK/FW bundle
- Implement timestamp and egress_queue_index hostif packet attributes.
Bugs fixes:
- Fix compilation issues with gcc10
- Fix return code for buffer overflow for query enum values and query statistics capabilities
- Reduce verbosity of print in case packet ingress on invalid port
- Fix mirror Qos settings
- How I did it
Updated SAI version and submodule pointer
- How to verify it
Run regression tests from sonic-mgmt
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
- Why I did it
Advance to Mellanox SAI ver 1.19.2 to pick up dynamic Policy Based Hashing support.
For this version above the static Policy Based Hashing is no longer supported.
For detailed release notes check https://github.com/Mellanox/SAI-Implementation/blob/sonic2111/release%20notes.txt
- How I did it
Updated SAI-Implementation submodule
- How to verify it
1. make configure PLATFORM=mellanox
2. make target/sonic-mellanox.bin
Run full regression as well as new dynamic PBH tests
Signed-off-by: Nazarii Hnydyn <nazariig@nvidia.com>
- Why I did it
Update SAI version to 1.19.1. The following was changed:
1. Update license
2. Do not remove and re-apply the same SDK mirror session on LAG
3. FEC fix to support all speeds
4. Improve PG counters performance
5. Fix number of switch priorities for port mirroring
Signed-off-by: Dror Prital <drorp@nvidia.com>
Why I did it
* For SAI - Upgrade to Version 1.19.0
- Add support for VxLAN encap TTL uniform model on SPC2/3
- Add ACL entry actions set VRF, set do no learn, add VLAN ID, add VLAN priority
- Add ACL field has VLAN tag
- Bulk counters (improve port statistics performance)
- Create async dump extra as part of debug generate dump
- Create irisc dump on severe health event
- Support 0 port systems (modify get switch mac to work accordingly)
- Set interface vlan up state for ping tool in SONiC
- Support attributes SAI_PORT_ATTR_QOS_SCHEDULER_PROFILE_ID, SAI_PORT_ATTR_QOS_INGRESS_BUFFER_PROFILE_LIST,
SAI_PORT_ATTR_QOS_EGRESS_BUFFER_PROFILE_LIST, SAI_PORT_ATTR_POLICER_ID as part of port create Git stats
* For SDK\FW - Upgrade to Version SDK 4.4.3106, FW 2008_3110
Added Features:
- Increased ACL table
- Enhanced PSAMPLE support
- Added support for Finisar SR4 module in SN3700 systems
- Added support for Python 3.0 in examples.
Fix bugs:
- On LR4 transceivers 00YD278, the firmware incorrectly identified the transceiver
- Reduce memory consumption for virtual LAG
- Fixed PSAMPLE listeners cleanup on SDK drivers unloading.
- On Spectrum-2 and Spectrum-3 systems, slow reaction time to Rx pause packets may lead to buffer overflow on servers.
- BER may be experienced when using 5m DAC cables between SN4700 and SN2700 in 100GbE speed.
- On very rare occasion, when connecting DR4 PAM4 transceiver to 100GbE DR1 NRZ, low BER may be experienced.
- Unexpected packet drops on the port ingress buffer may be experienced when working in 400GbE mode.
Note: When performing ISSU from an older version, this fix won't be applied. For fix to apply, a non-ISSU reset is required.
- Fix SN3800 specific warm boot scenario: Disable interface, Warm Boot, Enable Interface --> link will remain down.
Signed-off-by: Dror Prital <drorp@nvidia.com>
Changes in the new release:
Fix 10G and 50G speeds in SAI XML to support all interface types
Enable SMAC=DMAC and SMAC MC in tunnel debug counter
Add tunnel statistics
Add isolation group API implementation
Fix ACL ANY debug counter to correctly track ACL drops
Add VXLAN source port hard coded range, controlled by K/V
FW dump me now feature
Add mlxtrace to saidump
Speed lane setting and AN control
Implement query stats API
VNI miss part of tunnel decal drop reason
Align with SAI API v1.8.1
Signed-off-by: Dror Prital <drorp@nvidia.com>
Changes in the new release:
1. Policy based hashing optimization
2. New attribute support for Max port headroom
3. Tunnel ECN map fixes
4. Tunnel EVPN skeleton extensions (peer attrib, maps)
5. Bridge port admin not affecting port admin (optimize port down time)
6. CRM new API for neighbors and tunnel termination entries
7. Improve FDB event for flush by bridge port (before, null bridge was reported to SONiC, now the bridge will be extracted from bridge port)
8. DHCP L2 v4+v6 traps (for ZTP use case)
9. Generic counter implementation
Signed-off-by: Kebo Liu <kebol@nvidia.com>
* [Mellanox] Update SAI to 1.18.0
* [Mellanox] Update SDK to 4.4.2112
* Updated Mellanox SAI to 1.18.0.2
* Updated bcmsai debians to use SAI 1.7.1
* Updated Mellanox to use SAI 1.7.1
* Updated submodule sonic-sairedis using SAI 1.7.1
Co-authored-by: Vineet Mittal <vmittalmittal@microsoft.com>
Co-authored-by: Nazarii Hnydyn <nazariig@nvidia.com>
when parallel build is enabled, both docker-fpm-frr and docker-syncd-brcm
is built at the same time, docker-fpm-frr requires swss which requires to
install libsaivs-dev. docker-syncd-brcm requires syncd package which requires
to install libsaibcm-dev.
since libsaivs-dev and libsaibcm-dev install the sai header in the same
location, these two packages cannot be installed at the same time. Therefore,
we need to serialize the build between these two packages. Simply uninstall
the conflict package is not enough to solve this issue. The correct solution
is to have one package wait for another package to be uninstalled.
For example, if syncd is built first, then it will install libsaibcm-dev.
Meanwhile, if the swss build job starts and tries to install libsaivs-dev,
it will first try to query if libsaibcm-dev is installed or not. if it is
installed, then it will wait until libsaibcm-dev is uninstalled. After syncd
job is finished, it will uninstall libsaibcm-dev and swss build job will be
unblocked.
To solve this issue, _UNINSTALLS is introduced to uninstall a package that
is no longer needed and to allow blocked job to continue.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
make swss build depends only on libsairedis instead of syncd. This allows to build swss without depending
on vendor sai library.
Currently, libsairedis build also buils syncd which requires vendor SAI lib. This makes difficult to build
swss docker in buster while still keeping syncd docker in stretch, as swss requires libsairedis which also
build syncd and requires vendor to provide SAI for buster. As swss docker does not really contain syncd
binary, so it is not necessary to build syncd for swss docker.
* [submodule]: update sonic-sairedis
* ccbb3bc 2020-06-28 | add option to build without syncd (HEAD, origin/master, origin/HEAD) [Guohan Lu]
* 4247481 2020-06-28 | install saidiscovery into syncd package [Guohan Lu]
* 61b8e8e 2020-06-26 | Revert "sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624)" (#630) [Danny Allen]
* 85e543c 2020-06-26 | add a README to tests directory to describe how to run 'make check' (#629) [Syd Logan]
* 2772f15 2020-06-26 | sonic-sairedis: Add support to sonic-sairedis for gearbox phys (#624) [Syd Logan]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
1. Upgrade SAI headers to v1.6.3
2. Fix traffic lost during FFB related to buffer config + optimize buffer config timing for FB
3. Add ACL fields BTH, IP flags
4. Add ACL infrastructure of different fields per ASIC type
* Update sonic-sairedis (sairedis with SAI 1.6 headers)
* Update SAIBCM to 3.7.4.2, which is built upon SAI1.6 headers
* missed updating BRCM_SAI variable, fixed it
* Update SAIBCM to 3.7.4.2, updated link to libsaibcm
* [Mellanox] Update SAI (release:v1.16.3; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* Update sonic-sairedis pointer to include SAI1.6 headers
* [Mellanox] Update SDK to 4.4.0914 and FW to xx.2007.1112 to match SAI 1.16.3 (API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* ensure the veth link is up in docker VS container
* ensure the veth link is up in docker VS container
* [Mellanox] Update SAI (release:v1.16.3.2; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* use 'config interface startup' instead of using ifconfig command, also undid the previous change'
Co-authored-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
Update SAI/SDK/FW and MSN4700 device files to support 8 lanes 400G
Update SAI to 1.16.3
Update SDK to 4.4.0914
Update FW to *.2007.1112
Update MSN4700 device files to support 8 lanes 400G
update FW to xx_2000_3298
update SAI to 1.16.0
update Spectrum-1 and Spectrum-2 buffer pool size according to the new SDK default config change.
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t1.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t1.j2
modified: fw.mk
modified: mlnx-sai.mk
modified: mlnx-sai/SAI-Implementation
modified: sdk-src/sx-kernel/Switch-SDK-drivers
modified: sdk.mk
signed-off by kebol@mellanox.com
* [submodule] update sonic-linux-kernel
* update linux kernel version
* Fix many version strings
* update mellanox components (built with new kernel)
* [mlnx] add make files for SDK WJH libs
* Update arista driver submodule (#8)
Make the debian packaging point to a newer kernel version.
