Why I did it
#4021 describes an issue that is still being observed on master image whereby sensord does not start in pmon due to missing service.
How I did it
Updated the lm-sensors install patch with a case for systemd
How to verify it
Verified that sensord is up in pmon after boot
Co-authored-by: Boyang Yu <byu@arista.com>
- Skip the interface status check if the interface does not exist. In the future, when the interface is created/comes up this check will be triggered again.
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
fix linecard provisioning issue (500 error)
fix some value types for get_system_eeprom_info API
refactor code to leverage pci topology (enabling dynamic Pcie plugin)
refactor asic declaration logic to new style
misc fixes
Fixing issue FRRouting/frr#11108
For interface based peers with peer-groups, "no neighbor capability extended-nexthop" gets added by default. This will result in IPv4 routes not having ipv6 next hops.
- How I did it
Porting the commit FRRouting/frr@8e89adc to FRR 8.2.2 which fixes the issue
- How to verify it
Load FRR and verify if the "no neighbor capability extended-nexthop" not gets added for interfaces associated with peer-groups
- Why I did it
A new SKU for MSN4700 Platform i.e. Mellanox-SN4700-V16A96
Requirements:
Breakout:
Port 1-24: 4x25G(4)[10G,1G]
Port 25-28: 2x100G[200G,50G,40G,25G,10G,1G]
Port 29-32: 2x200G[100G,50G,40G,25G,10G,1G]
Downlinks: 96 (1-24) + 4 (25-28)
Uplinks: 4 (29-32)
Shared Headroom: Enabled
Over Subscribe Ratio: 1:4
Default Topology: T0
Default Cable Length for T1: 5m
VxLAN source port range set: No
Static Policy Based Hashing Supported: No
Additional Details:
QoS params: The default ones defined in qos_config.j2 will be applied
Small Packet Percentage: Used 50% for traditional buffer model Note: For dynamic model, the value defined in LOSSLESS_TRAFFIC_PATTERN|AZURE|small_packet_percentage is used
SKU was drafted under the assumption that the downlink ports uses xcvr's that will only support the first 4 lanes of the physical port they are connected to. Hence for the ports 1-24, the last four lanes are not used
Cable Lengths used for generating buffer_defaults_{t0,t1}.j2 values
Signed-off-by: Vivek Reddy Karri <vkarri@nvidia.com>
- Why I did it
Update sonic-platform-common submodule pointer to include the following:
Read CMIS data path state duration (#312)
Remove shell=True (#313)
[credo][ycable] remove mux-toggle inprogress flags for some API's (#311)
[Cdb fw upgrade (#308)
[Credo][Ycable] enhancement and error exception for some APIs (#303)
[ycable] add definitions of some new API's for Y-Cable infrastructure (#301)
Install libyang to azure pipeline (#310)
Update the return of update_firmware for the image not exist case (#306)
[CMIS] 'get_transceiver_info' should return 'None' when CMIS cable EEPROM is not ready (#305)
uplift code coverage 80% (#307)
[sonic-pcie] Add UT for pcie_common.py (#293)
[CMIS] Catch Exception to avoid CMIS code crash (#299)
[Credo][Ycable] fix incorrect uart statistics (#296)
Add PSU input voltage and input current (#295)
- How I did it
Advance sonic-platform-common pointer
Signed-off-by: dprital <drorp@nvidia.com>
- Why I did it
Update sonic-sairedis submodule pointer to include the following:
2585a1f [Support gearbox SAI_PORT_ATTR_PORT_SERDES_ID on vs (#1082)
fd9bc84 [SAI NAT aging notification (#987)
3fa8f34 [[doc]: Update README.md (#1122)
157e573 [[lgtm] Fix libyang missing in lgtm validation issue (#1135)
af80caa Add Voqs to Virtual Switch (#1061)
f9008ad [fastboot] fastboot enhancement: Use warm-boot infrastructure for fast-boot (#1100)
- How I did it
Advance sonic-sairedis pointer
Signed-off-by: dprital <drorp@nvidia.com>
- Why I did it
Barefoot uses hysteresis, instead of 'xon-threshold'. 'xon' is only
supported in static mode, so there is a need to add this attribute
to every mode in PG profile init file
- How I did it
'xon_offset' was added to pg_profile_lookup.ini
- How to verify it
Install and basic sanity tests including traffic.
Checked with:
pfcwd/test_pfc_config.py pfcwd/test_pfcwd_all_port_storm.py
pfcwd/test_pfcwd_function.py pfcwd/test_pfcwd_war_reboot.py
pfc_asym/test_pfc_asym.py
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Why I did it
Revert change in syslog such that it does not utilize c++ string
How I did it
Code change
How to verify it
Which release branch to backport (provide reason below if selected)
201811
201911
202006
202012
202106
202111
202205
Description for the changelog
Ensure to add label/tag for the feature raised. example - PR#2174 under sonic-utilities repo. where, Generic Config and Update feature has been labelled as GCU.
Link to config_db schema for YANG module changes
A picture of a cute animal (not mandatory but encouraged)
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
What I did
Adding the dynamic headroom calculation support for Barefoot platforms.
Why I did it
Enabling dynamic mode for barefoot case.
How I verified it
The community tests are adjusted and pass.
co-authorized by: jianquanye@microsoft.com
Migrate the t0 and t1-lag test jobs in buildimage repo to TestbedV2.
Why I did it
Migrate the t0 and t1-lag test jobs in buildimage repo to TestbedV2.
How I did it
Migrate the t0 and t1-lag test jobs in buildimage repo to TestbedV2.
A new SKU for MSN4700 Platform i.e. Mellanox-SN4700-V48C32
Requirements:
Breakout:
Port 1-24: 2x200G
Port 25-32: 4x100G
Downlinks: 48 (1-24)
Uplinks: 32 (25-32)
Shared Headroom: Enabled
Over Subscribe Ratio: 1:8
Default Topology: T1
Default Cable Length for T1: 300m
VxLAN source port range set: No
Static Policy Based Hashing Supported: No
Additional Details:
QoS params: The default ones defined in qos_config.j2 will be applied
Small Packet Percentage: Used 50% for traditional buffer model Note: For dynamic model, the value defined in LOSSLESS_TRAFFIC_PATTERN|AZURE|small_packet_percentage is used
Cable Lengths used for generating buffer_defaults_{t0,t1}.j2 values
Signed-off-by: Vivek Reddy Karri <vkarri@nvidia.com>
Why I did it
The Dockerfile of docker-sonic-mgmt became a little bit messy over time. Some packages are also a little bit too old. It would be better to do some cleanup and upgrade some important packages.
How I did it
Updated the dockerfile template for building docker-sonic-mgmt.
How to verify it
Locally built the docker-sonic-mgmt image and used it to run some test scripts.
Description for the changelog:
The build-essential package contains gcc and make. It's unnecessary to install them again.
The python-is-python2 package is included in the python package for Ubuntu 20.04. It's unnecessary to install it again.
Sort the apt and pip packages by alphabetic order.
Cleanup get-pip.py after installation.
Cleanup the python-scapy deb package after installation.
Ensure that the python pip, setuptools and wheel packages are up to date.
Install pytest-ansible from pip instead of from source code.
While installing docker-ce-cli, it's unnecessary to install curl and software-properties-common again.
Merged some pip install steps into one step.
Upgrade ansible from 2.8.12 to 2.9.27 for env-python3.
Upgrade pytest to 7.1.3 for env-python3.
Add ncclient package to evn-python3.
* Add smartmontools to pmon docker
* Set smartmontools to install version 7.2-1 in pmon to match host; clean up smartmontools build files
* Add comments on smartmontools version for both host and pmon
What I did
Filter port invalid MTU configuration
How I did it
Adjust the MTU value to the range of [68,9216]
How to verify it
Use "config interface mtu Ethernet1 40" command to configure the port MTU. The following error will occur in SWSS.
Why I did it
There is an outstanding FRR issue #12380. This seems to be a known issue but without good fix so far. The root cause is around zebra and kernel netlink interaction. The failure was previously not noticed by zebra.
How I did it
Port the patch that would make the issue obvious.
Signed-off-by: Ying Xie ying.xie@microsoft.com
#### Why I did it
To add new SKU Mellanox-SN2700-D44C10 with following requirements:
| Port configuration | Value |
| ------ |--------- |
| Breakout mode for each port |**Defined in port mapping** |
| Speed of the port | **Defined in Port mapping** |
| Auto-negotiation enable/disable | **No setting required** |
| FEC mode | **No setting required** |
|Type of transceiver used | **Not needed**|
Buffer configuration | Value
------ |---------
Shared headroom | **Enabled**
Shared headroom pool factor | **2**
Dynamic Buffer | **Disable**
In static buffer scenario how many uplinks and downlinks? | **44 x50G and 2x100G Downlinks 8x100G uplinks**
2km cable support required? | **No**
Switch configuration | Value
------ |---------
Warmboot enabled? | **yes**
Should warmboot be added to SAI profile when enabled? | **yes**
Is VxLAN source port range set? | **No**
Should Vxlan source port range be added to SAI profile when set. | **No**
Is Static Policy Based Hashing enabled? | **No**
Port Mapping
| Ports | Mode |
| ------ |--------- |
| 1,2 | 1x100G |
| 3-6 | 2x50G |
| 7-10 | 1x100G |
| 11-22 | 2x50G |
| 23-26 | 1x100G |
| 27-32 | 2x50G |
Number of Uplinks / Downlinks:
TO topology: **44 x50G and 2x100G Downlinks 8x100G uplinks**.
#### How I did it
Defined the SKU as per requirements
#### How to verify it
Load the SKU and verify if all links come up and traffic passes.
changes:
-- yang model for dhcp_server table.
-- tests.
Why I did it
yang model for dhcp_server table.
How I did it
-- yang model for dhcp_server table.
-- yang model tests.
How to verify it
-- yang model build time tests.
changes:
-- yang model for mpls_tc_to_tc_map table.
-- tests.
#### Why I did it
yang model for mpls_tc_to_tc_map table.
#### How I did it
-- yang model for mpls_tc_to_tc_map table.
-- yang model tests.
#### How to verify it
-- yang model build time tests.
Why I did it
BGP service has always been starting after interface-config. However, recently we discovered an issue where some BGP sessions are unable to establish due to BGP daemon not able to read the interface IP.
This issue was clearly observed after upgrading to FRR 8.2.2. See more details in #12380.
How I did it
Delaying starting BGP seems to be a workaround for this issue.
However, caution is that this delay might impact warm reboot timing and other timing sequences.
This workaround is reducing the probability of hitting the issue by close to 100X. However, this workaround is not bulletproof as test shows. It is still preferrable to have a proper FRR fix and revert this change in the future.
How to verify it
Continuously issuing config reload and check BGP session status afterwards.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
This PR fixes the issue reported in PR#12367
https://github.com/sonic-net/sonic-buildimage/pull/12367
The issue is that exit code always being 0 for the builds that are failed.
Fix is added in the Makefile.work to return the error code
when the slave build is failed with an error.
This is causing a build failure for all builds. The PR build was incorrectly marked as passing due to a different build issue.
libyang[0]: Regular expression "(/[a-zA-Z0-9_-.]+)*/([a-zA-Z0-9_-.]+)./[a-z]{3}" is not valid (".]+)*/([a-zA-Z0-9_-.]+)./[a-z]{3})$": range out of order in character class).
libyang[0]: Module "sonic-restapi" parsing failed.
ERROR:YANG-TEST: Exception >Module "sonic-restapi" parsing failed.< in /sonic/src/sonic-yang-models/tests/yang_model_tests/test_yang_model.py:114
ERROR:YANG-TEST: Exception >Module "sonic-restapi" parsing failed.< in /sonic/src/sonic-yang-models/tests/yang_model_test
This reverts commit e1765121b2.
- Why I did it
Fixes#11431
- How I did it
dhcp6relay binds to ipv6 addresses configured on these vlan interfaces
Thus check if they are ready before launching dhcp6relay
- How to verify it
Unit Tests
Tested on a live device
Signed-off-by: Vivek Reddy Karri <vkarri@nvidia.com>
Remove swsssdk from sonic OS image and docker image
#### Why I did it
swsssdk is deprecated, so need remove from image.
#### How I did it
Update config file to remove swsssdk from image.
#### How to verify it
Pass all test case.
#### Which release branch to backport (provide reason below if selected)
<!--
- Note we only backport fixes to a release branch, *not* features!
- Please also provide a reason for the backporting below.
- e.g.
- [x] 202006
-->
- [ ] 201811
- [ ] 201911
- [ ] 202006
- [ ] 202012
- [ ] 202106
- [ ] 202111
- [ ] 202205
#### Description for the changelog
Remove swsssdk from sonic OS image and docker image
#### Ensure to add label/tag for the feature raised. example - PR#2174 under sonic-utilities repo. where, Generic Config and Update feature has been labelled as GCU.
#### Link to config_db schema for YANG module changes
<!--
Provide a link to config_db schema for the table for which YANG model
is defined
Link should point to correct section on https://github.com/Azure/sonic-buildimage/blob/master/src/sonic-yang-models/doc/Configuration.md
-->
#### A picture of a cute animal (not mandatory but encouraged)
Signed-off-by: maipbui <maibui@microsoft.com>
#### Why I did it
`eval()` - not secure against maliciously constructed input, can be dangerous if used to evaluate dynamic content. This may be a code injection vulnerability.
#### How I did it
`eval()` - use `literal_eval()`
changed the platform device name under nokia directory; we now need to specify marvell armhf/arm64 to provide more accurate platform identity. otherwise onie discovery won't recognize the asic being installed.
Why I did it
when we load images using onie discovery, the process was failing because of marvell ASIC mismatch
How I did it
replace the platform asic with marvell-armhf under 7215
How to verify it
load a new image using http server and verify that the image can be loaded successfully
