Cherypick of #15685
MSFT ADO: 24274591
Why I did it
Two changes:
1 Fix a day1 issue, where check to wait until CONFIG_DB_INITIALIZED is incorrect.
There are multiple places where same incorrect logic is used.
Current logic (until [[ $($SONIC_DB_CLI CONFIG_DB GET "CONFIG_DB_INITIALIZED") ]];) will always result in pass, irrespective of the result of GET operation.
root@str2-7060cx-32s-29:~# sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED"
1
root@str2-7060cx-32s-29:~# until [[ $(sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED") ]]; do echo "entered here"; done
root@str2-7060cx-32s-29:~#
root@str2-7060cx-32s-29:~#
root@str2-7060cx-32s-29:~# sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED"
0
root@str2-7060cx-32s-29:~# until [[ $(sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED") ]]; do echo "entered here"; done
root@str2-7060cx-32s-29:~#
Fix this logic by checking for value of flag to be "1".
root@str2-7060cx-32s-29:~# until [[ $(sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED") -eq 1 ]]; do echo "entered here"; done
entered here
entered here
entered here
This gap in logic was highlighted when another fix was merged: #14933
The issue being fixed here caused warmboot-finalizer to not wait until config-db is initialized.
2 Set and unset CONFIG_DB_INITIALIZED for warm-reboot case
Currently, during warm shutdown CONFIG_DB_INITIALIZED's value is stored in redis db backup. This is restored back when the dump is loaded during warm-recovery.
So the value of CONFIG_DB_INITIALIZED does not depend on config db's state, however it remain what it was before reboot.
Fix this by setting CONFIG_DB_INITIALIZED to 0 as when the DB is loaded, and set it to 1 after db_migrator is done.
Work item tracking
Microsoft ADO (number only):
How I did it
How to verify it
#### Why I did it
src/linkmgrd
```
* 40113fd - (HEAD -> 202305, origin/202305) [active-standby] Fix extra toggle observed in `config reload` (#216) (2 days ago) [Longxiang Lyu]
* b6d40fc - Add ADO to the PR template (#215) (2 days ago) [Longxiang Lyu]
* fe41ad2 - [active-standby] Write `unhealthy` is default route `N/A` (#214) (2 days ago) [Longxiang Lyu]
* 8ff265c - [link prober] Increase pause/restart probe log verbosity (#213) (2 days ago) [Longxiang Lyu]
```
#### How I did it
#### How to verify it
#### Description for the changelog
#### Why I did it
src/sonic-platform-daemons
```
* 4688e1e - (HEAD -> 202305, origin/202305) [PSU power threshold] Fix logic error: compare the system power with the PSU's power threshold (#367) (2 days ago) [Stephen Sun]
```
#### How I did it
#### How to verify it
#### Description for the changelog
#### Why I did it
src/sonic-swss
```
* 6b0c8c5c - (HEAD -> 202305, origin/202305) [muxorch] set mux state to init upon warm reboot (#2834) (18 hours ago) [Nikola Dancejic]
* bc9bde94 - [ASAN] Fix Indirect Mem Leaks in Orchagent (#2869) (24 hours ago) [Vivek]
```
#### How I did it
#### How to verify it
#### Description for the changelog
fix static route uninstall issue when all nexthops are not reachable.
the feature was working but the bug was introduced when support dynamic bfd enable/disable. Added UT testcase to guard this.
### Why I did it
Background running lua script may cause redis-server quite busy if batch size is 8192.
If handling time exceeded default 5s, the redis-server will not response to other process and will cause syncd crash.
```
Aug 9 07:46:29.512326 str-s6100-acs-5 INFO database#supervisord: redis 68:M 09 Aug 2023 07:46:29.511 # Lua slow script detected: still in execution after 5186 milliseconds. You can try killing the script using the SCRIPT KILL command. Script SHA1 is: 88270a7c5c90583e56425aca8af8a4b8c39fe757
Aug 9 07:46:29.523716 str-s6100-acs-5 ERR syncd#syncd: :- checkReplyType: Expected to get redis type 5 got type 6, err: BUSY Redis is busy running a script. You can only call SCRIPT KILL or SHUTDOWN NOSAVE.
Aug 9 07:46:29.524818 str-s6100-acs-5 INFO syncd#supervisord: syncd terminate called after throwing an instance of '
Aug 9 07:46:29.525268 str-s6100-acs-5 ERR pmon#CCmisApi: :- checkReplyType: Expected to get redis type 5 got type 6, err: BUSY Redis is busy running a script. You can only call SCRIPT KILL or SHUTDOWN NOSAVE.
Aug 9 07:46:29.526148 str-s6100-acs-5 INFO syncd#supervisord: syncd std::system_error'
Aug 9 07:46:29.528308 str-s6100-acs-5 ERR pmon#psud[32]: :- checkReplyType: Expected to get redis type 5 got type 6, err: BUSY Redis is busy running a script. You can only call SCRIPT KILL or SHUTDOWN NOSAVE.
Aug 9 07:46:29.529048 str-s6100-acs-5 ERR lldp#python3: :- guard: RedisReply catches system_error: command: *2#015#012$3#015#012DEL#015#012$27#015#012LLDP_ENTRY_TABLE:Ethernet37#015#012, reason: BUSY Redis is busy running a script. You can only call SCRIPT KILL or SHUTDOWN NOSAVE.: Input/output error
Aug 9 07:46:29.529720 str-s6100-acs-5 ERR snmp#python3: :- guard: RedisReply catches system_error: command: *2#015#012$7#015#012HGETALL#015#012$28#015#012COUNTERS:oid:0x100000000000a#015#012, reason: BUSY Redis is busy running a script. You can only call SCRIPT KILL or SHUTDOWN NOSAVE.: Input/output error
```
88270a7c5c90583e56425aca8af8a4b8c39fe757 is /usr/share/swss/consumer_state_table_pops.lua
##### Work item tracking
- Microsoft ADO **24741990**:
#### How I did it
Change batch size from 8192 to 1024.
#### How to verify it
Run all test cases in sonic-mgmt to verify the system stability.
### Tested branch (Please provide the tested image version)
- [x] 20220531.36
- Why I did it
Adjust PSU power threshold logic in system health.
- How I did it
Update the description message in PSU power threshold checking
power of PSU x (xx w) exceeds threshold (xx w) => System power exceeds xx threshold (xx w)
- How to verify it
Manual test and unit test
What I did:
Fix the Loopback0 IPv6 address of LC's in chassis not reachable from peer devices.
Why I did:
For Ipv6 Loopback0 address we only advertise /64 subnet to the peer devices. However, in case of chassis each LC will have it own /128 address of that /64 subnet . Since this /128 address does not get advertised peer devices can-not ping/reach the LC's loopback0.
How I fix:
Advertise /128 Loopback0 Ipv6 address only between i-BGP peers. This way even though /64 is advertised to e-BGP peer devices when packet reaches any of LC's it can reach the appropriate LC's.
How I verify:
Manual verification
UT added for same.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
Why I did it
get_system_mac was returning 'None' mac for system without eeprom.
get_system_mac for marvell platform checks for mac in eeprom, profile.ini(hwsku file) and eth0. Check for valid mac returned by syseeprom was incorrect. Which was resulting in bypassing mac get from profile.ini and eth0.
How I did it
get_system_mac already has a logic to get first valid mac.
Removed null check for mac returned by eeprom.
Corrected the check for profile.ini file by checking if file exist.
How to verify it
Executed sonic-cfggen to check valid mac address is getting configured in config_db.json with/without profile.ini.
Signed-off-by: Pavan Naregundi <pnaregundi@marvell.com>
cherry-pick: #14513
depends: https://github.com/sonic-net/sonic-utilities/pull/2939
* Add an ability to configure remote syslog servers
* Add an initial configuration for remote syslog
* Extend YANG module and add unit tests
#### Why I did it
Adding the following functionality to rsyslog feature:
* Configure remote syslog servers: protocol, filter, severity level
* Update global syslog configuration: severity level, message format
#### How I did it
added parameters to syslog server and global configuration.
#### How to verify it
create syslog server using CLI/adding to Redis-DB
verify server is added to file /etc/rsyslog.conf and server is functional.
#### Description for the changelog
extend rsyslog capabilities, added server and global configuration parameters.
#### Link to config_db schema for YANG module changes
[sonic-syslog.yang](https://github.com/sonic-net/sonic-buildimage/blob/master/src/sonic-yang-models/yang-models/sonic-syslog.yang)
Why I did it
Updating the iSMART_64 tool for supporting latest debian releases.
How I did it
On branch new_ismart
Changes to be committed:
(use "git restore --staged ..." to unstage)
modified: platform/broadcom/sonic-platform-modules-dell/s6100/scripts/iSMART_64
How to verify it
In s6100, run the iSMART_64 tool.
md5sum - 24725730d7649769c7ba50971c1f2955
Co-authored-by: Santhosh Kumar T <53558409+santhosh-kt@users.noreply.github.com>
- Why I did it
Increase UT coverage for Nvidia platform API code
Work item tracking
Microsoft ADO (number only):
- How I did it
Focus on low coverage file:
1. component.py
2. watchdog.py
3. pcie.py
- How to verify it
Run the unit test, the coverage has been changed from 70% to 90%
Co-authored-by: Junchao-Mellanox <57339448+Junchao-Mellanox@users.noreply.github.com>
#### Why I did it
event yang models for usage currently use int as type for usage leaf, needs to be of type decimal64
##### Work item tracking
- Microsoft ADO **(number only)**:17747466
#### How I did it
Update yang models and UT
#### How to verify it
UT
Co-authored-by: Zain Budhwani <99770260+zbud-msft@users.noreply.github.com>
Fixes#15667 and #13293
Work item tracking
Microsoft ADO 24472854:
How I did it
On chassis supervisor bgp feature is disabled in hostcfgd. The dependency between swss and bgp causes the bgp containers to start even though the feature is disabled.
How to verify it
Tests on chassis supervisor and LC
Co-authored-by: Arvindsrinivasan Lakshmi Narasimhan <55814491+arlakshm@users.noreply.github.com>
<!--
Please make sure you've read and understood our contributing guidelines:
https://github.com/Azure/SONiC/blob/gh-pages/CONTRIBUTING.md
** Make sure all your commits include a signature generated with `git commit -s` **
If this is a bug fix, make sure your description includes "fixes #xxxx", or
"closes #xxxx" or "resolves #xxxx"
Please provide the following information:
-->
#### Why I did it
fixes: https://github.com/sonic-net/sonic-buildimage/issues/16001
Caused by: https://github.com/sonic-net/sonic-buildimage/pull/15487
The above PR introduced change to use Management and Loopback Ipv4 and ipv6 addresses as snmpagent address in snmpd.conf file.
With this change, if Link local IP address is configured as management or Loopback IPv6 address, then snmpd tries to open socket on that ipv6 address and fails with the below error:
```
Error opening specified endpoint "udp6:[fe80::5054:ff:fe6f:16f0]:161"
Server Exiting with code 1
```
From RFC4007, if we need to specify non-global ipv6 address without ambiguity, we need to use zone id along with the ipv6 address: <address>%<zone_id>
Reference: https://datatracker.ietf.org/doc/html/rfc4007
##### Work item tracking
- Microsoft ADO **(number only)**:
#### How I did it
Modify snmpd.conf file to use the %zone_id representation for ipv6 address.
#### How to verify it
In VS testbed, modify config_db to use link local ipv6 address as management address:
"MGMT_INTERFACE": {
"eth0|10.250.0.101/24": {
"forced_mgmt_routes": [
"172.17.0.1/24"
],
"gwaddr": "10.250.0.1"
},
"eth0|fe80::5054:ff:fe6f:16f0/64": {
"gwaddr": "fe80::1"
}
},
Execute config_reload after the above change.
snmpd comes up and check if snmpd is listening on ipv4 and ipv6 addresses:
```
admin@vlab-01:~$ sudo netstat -tulnp | grep 161
tcp 0 0 127.0.0.1:3161 0.0.0.0:* LISTEN 274060/snmpd
udp 0 0 10.1.0.32:161 0.0.0.0:* 274060/snmpd
udp 0 0 10.250.0.101:161 0.0.0.0:* 274060/snmpd
udp6 0 0 fc00:1::32:161 :::* 274060/snmpd
udp6 0 0 fe80::5054:ff:fe6f::161 :::* 274060/snmpd -- Link local
admin@vlab-01:~$ sudo ifconfig eth0
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.250.0.101 netmask 255.255.255.0 broadcast 10.250.0.255
inet6 fe80::5054:ff:fe6f:16f0 prefixlen 64 scopeid 0x20<link>
ether 52:54:00:6f:16:f0 txqueuelen 1000 (Ethernet)
RX packets 36384 bytes 22878123 (21.8 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 261265 bytes 46585948 (44.4 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
admin@vlab-01:~$ docker exec -it snmp snmpget -v2c -c public fe80::5054:ff:fe6f:16f0 1.3.6.1.2.1.1.1.0
iso.3.6.1.2.1.1.1.0 = STRING: "SONiC Software Version: SONiC.master.327516-04a6031b2 - HwSku: Force10-S6000 - Distribution: Debian 11.7 - Kernel: 5.10.0-18-2-amd64"
```
Logs from snmpd:
```
Turning on AgentX master support.
NET-SNMP version 5.9
Connection from UDP/IPv6: [fe80::5054:ff:fe6f:16f0%eth0]:44308
```
Ran test_snmp_loopback test to check if loopback ipv4 and ipv6 works:
```
./run_tests.sh -n vms-kvm-t0 -d vlab-01 -c snmp/test_snmp_loopback.py -f vtestbed.yaml -i ../ansible/veos_vtb -e "--skip_sanity --disable_loganalyzer" -u
=== Running tests in groups ===
Running: pytest snmp/test_snmp_loopback.py --inventory ../ansible/veos_vtb --host-pattern vlab-01 --testbed vms-kvm-t0 --testbed_file vtestbed.yaml --log-cli-level warning --log-file-level debug --kube_master unset --showlocals --assert plain --show-capture no -rav --allow_recover --ignore=ptftests --ignore=acstests --ignore=saitests --ignore=scripts --ignore=k8s --ignore=sai_qualify --junit-xml=logs/tr.xml --log-file=logs/test.log --skip_sanity --disable_loganalyzer
..
snmp/test_snmp_loopback.py::test_snmp_loopback[vlab-01] PASSED
```
<!--
If PR needs to be backported, then the PR must be tested against the base branch and the earliest backport release branch and provide tested image version on these two branches. For example, if the PR is requested for master, 202211 and 202012, then the requester needs to provide test results on master and 202012.
-->
#### Which release branch to backport (provide reason below if selected)
<!--
- Note we only backport fixes to a release branch, *not* features!
- Please also provide a reason for the backporting below.
- e.g.
- [x] 202006
-->
- [ ] 201811
- [ ] 201911
- [ ] 202006
- [x] 202012
- [x] 202106
- [x] 202111
- [x] 202205
- [x] 202211
- [x] 202305
#### Tested branch (Please provide the tested image version)
<!--
- Please provide tested image version
- e.g.
- [x] 20201231.100
-->
- [ ] <!-- image version 1 -->
- [ ] <!-- image version 2 -->
#### Description for the changelog
<!--
Write a short (one line) summary that describes the changes in this
pull request for inclusion in the changelog:
-->
<!--
Ensure to add label/tag for the feature raised. example - PR#2174 under sonic-utilities repo. where, Generic Config and Update feature has been labelled as GCU.
-->
#### Link to config_db schema for YANG module changes
<!--
Provide a link to config_db schema for the table for which YANG model
is defined
Link should point to correct section on https://github.com/Azure/sonic-buildimage/blob/master/src/sonic-yang-models/doc/Configuration.md
-->
#### A picture of a cute animal (not mandatory but encouraged)
#### Why I did it
src/sonic-platform-common
```
* 5af6f9f - (HEAD -> 202305, origin/202305) Comment out tx power validation check and program the passed value (#389) (3 days ago) [abdosi]
```
#### How I did it
#### How to verify it
#### Description for the changelog
#### Why I did it
src/sonic-swss
```
* 27b64579 - (HEAD -> 202305, origin/202305) Remove system neighbor DEL operation in m_toSync if SET operation for (#2853) (3 days ago) [Song Yuan]
```
#### How I did it
#### How to verify it
#### Description for the changelog
#### Why I did it
src/sonic-swss-common
```
* 449ac55 - (HEAD -> 202305, origin/202305) [Ci] Fix collect log error in azp template (#799) (2 days ago) [xumia]
```
#### How I did it
#### How to verify it
#### Description for the changelog
#### Why I did it
src/sonic-linux-kernel
```
* bf1ee0e - (HEAD -> 202305, origin/202305) Fix Makefile syntax and provide default value for CONFIGURED_PLATFORM (#324) (13 hours ago) [Saikrishna Arcot]
* 7d7abaf - Update codeowner and build info (#319) (13 hours ago) [Saikrishna Arcot]
```
#### How I did it
#### How to verify it
#### Description for the changelog
Why I did it
Fix some of the patches in .patches folder not applied issue.
The command "quilt applied" only lists the applied patches, if some of the patches have issues, then the patches will not be applied when you run the build command again.
Work item tracking
Microsoft ADO (number only): 24410730
How I did it
Run the command to apply the patches without any conditions.
If failed, check if the failure reason is "series fully applied".
How to verify it
#### Why I did it
src/sonic-platform-daemons
```
* 6c47906 - (HEAD -> 202305, origin/202305) Update active application selected code in transceiver_info table aft… (#381) (13 hours ago) [Michael Wang - TW]
```
#### How I did it
#### How to verify it
#### Description for the changelog
#### Why I did it
When a kernel crash occurs, the system will reboot to the kdump capture kernel if kdump is enabled (`config kdump enable`). In the kdump capture boot, it only stores the crash information, and then reboot the system to a normal boot.
In this boot, no SONiC service is started but it invokes `reboot` which is actually the SONiC reboot that depends on SONiC services. There is a logic to skip all SONiC stuff and invoke platform reboot in SONiC reboot to avoid issues.
However, on Nvidia platforms, the platform reboot still depends on SONiC services, which can cause issues.
So, the Debian reboot is called directly in platform reboot if it is invoked from the kdump capture boot.
#### How I did it
Manual test
Why I did it
Sharing the storage of syncd with other proprietary application extensions allows them to communicate with syncd in differnt ways.
If one container wants to pass some information to syncd then shared storage can be used. However, today the shared storage isn't cleaned on restarts making it possible for syncd to read out-of-date information generated in the past.
NOTE: No plans to use it for standard SONIC dockers and we are working on removing the SDK dependency from PMON docker
How I did it
Implemented new service to clean the shared storage.
How to verify it
Do reboot/fast-reboot/warm-reboot/config-reload/systemctl restart swss and verify /tmp/ is cleaned after each restart in syncd container.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
Co-authored-by: Stepan Blyshchak <38952541+stepanblyschak@users.noreply.github.com>
Added support data for fabric monitoring in CONFIG_DB
The CONFIG_DB now has the FABRIC_MONITOR|FABRIC_MONITOR_DATA table for default value for fabric port monitoring. An example output of getting this table is:
sonic-db-cli CONFIG_DB hgetall "FABRIC_MONITOR|FABRIC_MONITOR_DATA"
{'monErrThreshCrcCells': '1', 'monErrThreshRxCells': '61035156', 'monPollThreshIsolation': '1', 'monPollThreshRecovery': '8'}
The CONFIG_DB now also has a table for each fabric port for its isolate status.
An example output of getting this table is:
sonic-db-cli CONFIG_DB hgetall "FABRIC_PORT|Fabric20"
{'alias': 'Fabric20', 'isolateStatus': 'False', 'lanes': '20'}
Co-authored-by: jfeng-arista <98421150+jfeng-arista@users.noreply.github.com>
There is a redundant line in init_cfg.json.j2. It would cause pmon service always has "delayed=False". However, we know that PMON has a timer now. So, I try to fix it here.
Why I did it
fix pcied leak on chassis
fix fan status led setting on fixed systems
misc fixes
Work item tracking
Microsoft ADO (number only):
How I did it
Updated arista platform library submodules
Description for the changelog
Update Arista platform submodules
Why I did it
Use remote PR test template from sonic-mgmt master to run PR test.
How I did it
Modify PR test azure pipeline yml file.
How to verify it
PR test executing normally.
Signed-off-by: Chun'ang Li <chunangli@microsoft.com>
#### Why I did it
src/sonic-platform-common
```
* 411d5b2 - (HEAD -> 202305, origin/202305) More prevention of fatal exception caused by VDM dictionary missing fields when a transceiver has just been pulled (#376) (2 days ago) [snider-nokia]
```
#### How I did it
#### How to verify it
#### Description for the changelog
