Why I did it
amrhf build fails while building sonic-config-engine whl package
https://dev.azure.com/mssonic/be1b070f-be15-4154-aade-b1d3bfb17054/_apis/build/builds/77089/logs/9
The reason for the failure is due to the fact that there is a new line generated at the top of the file in buffer config test cases while building for broadcom based platform and this issue is not seen in Marvell based platforms.
How I did it
Removed the new line for all the buffer test cases as there is no need to add it and accordingly changed the buffer_config.j2 where the new line is generated.
Why I did it
During warm-reboot and fast-reboot the below error logs appear
Feb 3 22:05:15.187408 r-lionfish-13 ERR container: docker cmd: kill for nat failed with 404 Client Error for http+docker://localhost/v1.41/containers/nat/json: Not Found ("No such container: nat")
The container command when called for local mode doesn't check if it is enabled before calling docker kill which throws the above errors.
b6ca76b482/scripts/fast-reboot (L699)
How I did it
Checking feature state if local mode and returning error exit code along with valid debug message.
How to verify it
Manually tested with warm-reboot and fast-reboot
Added UT to verify it.
PR #9481 changed auditd's log directory to be /var/log instead of
/var/log/audit, because SONiC mounts a disk image at /var/log during
runtime, and so the /var/log/audit directory might not exist (since it
would've been created during package installation, mounting another
partition at /var/log will hide it). However, for security reasons,
auditd changes the log directory to have 0750 permissions, so that not
everyone knows about the audit logs or read them.
To fix this, revert the change to auditd's log directory, and tell
systemd to create the audit log directory at runtime if it doesn't
exist. Because the disk image gets mounted during initramfs (before
systemd starts), systemd will make sure that the /var/log/audit
directory will exist.
Fixes#9548 and #10015
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
- Why I did it
The latest upgrade of Mellanox hw-mgmt V7.0020.1300 introduced a couple new kernel modules for new Mellanox platforms that have yet to be upstreamed to the linux kernel.
As these new platforms do not have SONiC support we elected not to upstream these new drivers to sonic-linux-kernel but hw-mgmt expects them to exist which is causing a non-functional error on switch boot.
Feb 15 00:09:55.374130 r-leopard-simx-74 ERR systemd-modules-load[269]: Failed to find module 'emc2305'
Feb 15 00:09:55.374141 r-leopard-simx-74 ERR systemd-modules-load[269]: Failed to find module 'ads1015'
To resolve this we can patch hw-mgmt to no longer attempt to load these modules by default.
- How I did it
Added a SONiC patch to Mellanox hw-mgmt in order to remove the unused kernel modules which were not upstreamed to sonic-linux-kernel
- How to verify it
Boot switch and verify there are no error logs regarding kernel modules failing to load.
- Why I did it
Stopping swss and syncd causes some driver module unloading. Those driver modules are depended by PMON. This could trigger ERROR logs in syslog.
- How I did it
Adjust warmboot shutdown order in make file
- How to verify it
Manual test
- Why I did it
In SONiC thermal control algorithm, it compares thermal zone temperature with thermal zone threshold. Previously, a thermal zone with no thermal sensor can still get its threshold. However, a recently driver patch changes this behavior: a thermal zone with no thermal sensor will return 0 for threshold. We need to ignore such thermal zone.
- How I did it
Ignore thermal zones whose temperature is 0.
- How to verify it
Added unit test case and Manual test
- Why I did it
swsscommon.ConfigDBConnector does not automatically close connection when the instance is recycled by python. So, it should not create this instance each time calling check_services. It will cause error like Failed to read from file /var/run/hw-management/led/led_status_capability - OSError(24, 'Too many open files')
- How I did it
Only connect DB once in init
- How to verify it
Manual test
Why I did it
In the recent minigraph changes we add separate BGP session configuration for V4 and V6 internal VoQ neighbors.
This PR is adding different Peer groups for V4 and V6 neighbors
How I did it
Add VOQ_CHASSIS_V4_PEER and VOQ_CHASSIS_V6_PEER groups
Add extra Unit tests
How to verify it
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
5331ecd [vslib]: Fix MACsec bug in SCI and XPN (#1003)
ac04509 Fix build issues on gcc-10 (#999)
1b8ce97 [pipeline] Download swss common artifact in a separated directory (#995)
7a2e096 Change sonic-buildimage.vs artifact source from CI build to official build. (#992)
d5866a3 [vslib]: fix create MACsec SA error (#986)
f36f7ce Added Support for enum query capability of Nexthop Group Type. (#989)
323b89b Support for MACsec statistics (#892)
26a8a12 Prevent other notification event storms to keep enqueue unchecked and drained all memory that leads to crashing the switch router (#968)
0cb253a Fix object availability conversion (#974)
Enable dbgsym package for dhcpmon.
Allow CFLAGS and LDFLAGS from environment variables to be used
in the dhcp6relay build. This makes sure that the -O2 flag from
dpkg-buildflags gets used.
Finally, enable all hardening flags in dpkg-buildflags for
dhcp6relay and dhcpmon. The change from the default set of flags is that
during linking, immediate binding of symbols is done instead of lazy
binding.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
sonic-swss
1aa40f7 Remove port serdes object before removing port (#2152)
876d690 [doc] Updating Policer config in Configuration manual (#2144)
sonic-utilities
dfed952 show_platfom_info not run for simx (#2042)
71fdee7 [aclshow] fix aclshow when clear is called before counters are populated (#2037)
a48a027 [sonic-package-manager] implement blocking feature state change (#2035)
c51871d [ci] Fix python dependencies reference path. (#2060)
Why I did it
Radvd.conf.j2 template creates two copies of the vlan interface when there are more than one ipv6 address assigned to a single vlan interface. Changed the format to add prefixes under the same vlan interface block.
How I did it
Modifies radvd.conf.j2 and added unit tests
How to verify it
Configure multiple ipv6 address to the same vlan, start radvd
Unit test will check if radvd.conf with multiple ipv6 addresses is formed correctly
This issue causes negative threshold value and thus deleting log files even when there is enough space.
This issue causes negative threshold value and thus deleting log files even when there is enough space.
- Why I did it
To fix an issue when log files get deleted even if there is enough space.
- How I did it
Fixed an typo.
- How to verify it
Run the portion of the script that calculates threshold, see that the threshold is calculated correctly.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
Why I did it
the strcpy and buffer allocation is not safe, it corrupts 1 byte on the stack. Depending on the memory layout, it may or may not cause issue immediately.
message type is not validated before updating the counter. Which could cause segment fault.
How I did it
Remove the unsafe strcpy, use config->interface.c_str() instead.
Check message type before updating counters.
How to verify it
The issue (1) caused segment fault on a specific platform. The fix was validated there. Issue (2) was precautionary. Added log in case it triggers.
- Why I did it
Update MFT to version 4.18.1-16 for bugs fixes and new SN2201 support
- How I did it
Advance to MFT tool version to 4.18.1-16
- How to verify it
Manually tested on all Mellanox platforms (ASIC FW Upgrade, link debug tools, CPLD upgrade, etc.)
- Why I did it
Error log was shown on switches during boot
pmon#supervisord 2021-12-22 04:27:16,709 INFO exited: chassis_db_init (exit status 0; not expected)
- How I did it
Add exit code zero as an expected exit code and also disable autorestart.
- How to verify it
Boot the switch and ensure the above log line does not appear.
cb3ddf5 [pmon][xcvrd] xcvrd process show backtrace on the internal port. Port PR233 (#236)
5b4c9e1 Fix python wheels path downloaded from vs official build. (#244)
- Why I did it
Fix Issue 9972: Incorrect information about release version in sonic_version.yml
- How I did it
Add "sonic_release" file to /sonic-buildimage/files/image_config/
- How to verify it
Install the image and run: cat /etc/sonic/sonic_version.yml
Verify the following item on sonic_version.yml file: release: '202111'
- Why I did it
platform.json of 4600C only has 2 CPU core thermal sensors, but there are 4 actually
- How I did it
Added thermal sensors for CPU core 2 and core 3.
- How to verify it
Build.
- Why I did it
The chassis name in MSN4410 platform_components.json is not correct
- How I did it
Fix the chassis name
- How to verify it
Run relevant platform API test
Signed-off-by: Kebo Liu <kebol@nvidia.com>
ded0344 Return both 'vendor_rev' and 'hardware_rev' keys from get_transceiver_info to support both earlier and later versions of xcvrd
b3442cc Change log_error to log_info when transceiver module is transitioned
3d3a73c Fix problem introduced with new SFP caching paradigm
2915746 Add script to reboot all IMMs
17ad221 Fix the position_in_parent for the psu entity
207e731 No longer force read pages at SFP init time
b387921 Fixed the voltage and power with rounding to 2 digit decimals
Signed-off-by: mlok <marty.lok@nokia.com>
Why I did it
Updated the BCM config recommended by Broadcom for Nokia-IXR7250E-36x400G
How I did it
Updated the BCM config file
How to verify it
Verified running the image with this BCM config in Nokia-IXR7250E-36x400G and ensured that the syncd container was stable, ports were up and passing the traffic.
Signed-off-by: Sakthivadivu Saravanaraj <sakthivadivu.saravanaraj@nokia.com>
[Build]: Fix hundreds of thousands lines of logs printed in marvell-armhf
It is caused by the bad format of the marvell sai package mrvllibsai_armhf_1.7.1-6.deb, increasing the waiting time to reduce the logs, and reduce the waste of the CPU.
- Why I did it
Need to remove old static configs from sai.profile files.
New implementation: Azure/sonic-swss#1959
New configuration: #9658
- How I did it
Remove SAI_VXLAN_SRCPORT_RANGE_ENABLE=1 lines from files per HWSKU
- How to verify it
When static config is removed following test will fail (src port will be in range 0-255)
py.test vxlan/test_vnet_vxlan.py --inventory "../ansible/inventory, ../ansible/veos" --host-pattern (testbed)-t0 --module-path ../ansible/library/ --testbed (testbed)-t0 --testbed_file ../ansible/testbed.csv --allow_recover --assert plain --log-cli-level info --show-capture=no -ra --showlocals --disable_loganalyzer --skip_sanity --upper_bound_udp_port 65535 --lower_bound_udp_port 64128
- Why I did it
Remove obsolete parameter that enables static VXLAN src port range
provide functionality no generate json config file according to appropriate parameter in config_db
Done for
SN3800:
• Mellanox-SN3800-D28C50
• Mellanox-SN3800-C64
• Mellanox-SN3800-D28C49S1 (New 10G SKU)
SN2700:
• Mellanox-SN2700-D48C8
- How I did it
Remove SAI_VXLAN_SRCPORT_RANGE_ENABLE=1 from appropriate sai.profile files
Created vxlan.json file and added few params that depends on DEVICE_METADATA.localhost.vxlan_port_range
- How to verify it
File /etc/swss/config.d/vxlan.json should be generated inside swss docker when it restart
[
{
"SWITCH_TABLE:switch": {
"vxlan_src": "0xFF00",
"vxlan_mask": "8"
},
"OP": "SET"
}
]
Signed-off-by: Andriy Yurkiv <ayurkiv@nvidia.com>
- Why I did it
New version of mellanox platform management code available adding support for new platforms and fixing bugs.
- How I did it
1. Updated the submodule
2. Updated makefile version references
3. Regenerated SONiC patches
Added midplane_subnet in chassisdb.conf for interfaces-config.sh to create midplane interface in multi-asic namespaces.
Signed-off-by: Sakthivadivu Saravanaraj <sakthivadivu.saravanaraj@nokia.com>
#### Why I did it
PR9611 - sonic-scheduler.yang pattern issue
#### How I did it
Modified the scheduler name pattern string to accept any string
#### How to verify it
Sonic yang tests
Why I did it
Need to be able to run smartctl when pmon docker is not running.
How I did it
Removed the pmon dependency for pmon as well as the command wrapper and added it to the debian-extension.
How to verify it
Stop pmon
Run smartctl from the host and verify it runs without error
Updates include the following changes in order to support new Mellanox platforms and drivers (Azure/sonic-linux-kernel#259)
10ef390 Update kconfig to support / enable newly backported mellanox patches.
6a949e1 Add backported patches for Mellanox hw-mgmt V.7.0020.1300
e1913f7 Rename and reformat patch headers
