sonic-buildimage/platform/broadcom/sonic-platform-modules-cel/dx010/modules/emc2305.c

/*
 * emc2305.c - hwmon driver for SMSC EMC2305 fan controller
 * (C) Copyright 2013
 * Reinhard Pfau, Guntermann & Drunck GmbH <pfau@gdsys.de>
 *
 * Based on emc2103 driver by SMSC.
 *
 * Datasheet available at:
 * http://www.smsc.com/Downloads/SMSC/Downloads_Public/Data_Sheets/2305.pdf
 *
 * Also supports the EMC2303 fan controller which has the same functionality
 * and register layout as EMC2305, but supports only up to 3 fans instead of 5.
 *
 * Also supports EMC2302 (up to 2 fans) and EMC2301 (1 fan) fan controller.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

/*
 * TODO / IDEAS:
 * - expose more of the configuration and features
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
#include <linux/of.h>

/*
 * Addresses scanned.
 * Listed in the same order as they appear in the EMC2305, EMC2303 data sheets.
 *
 * Note: these are the I2C adresses which are possible for EMC2305 and EMC2303
 * chips.
 * The EMC2302 supports only 0x2e (EMC2302-1) and 0x2f (EMC2302-2).
 * The EMC2301 supports only 0x2f.
 */
static const unsigned short i2c_adresses[] = {
	0x2E,
	0x2F,
	0x2C,
	0x2D,
	0x4C,
	0x4D,
	I2C_CLIENT_END
};

/*
 * global registers
 */
enum {
	REG_CONFIGURATION = 0x20,
	REG_FAN_STATUS = 0x24,
	REG_FAN_STALL_STATUS = 0x25,
	REG_FAN_SPIN_STATUS = 0x26,
	REG_DRIVE_FAIL_STATUS = 0x27,
	REG_FAN_INTERRUPT_ENABLE = 0x29,
	REG_PWM_POLARITY_CONFIG = 0x2a,
	REG_PWM_OUTPUT_CONFIG = 0x2b,
	REG_PWM_BASE_FREQ_1 = 0x2c,
	REG_PWM_BASE_FREQ_2 = 0x2d,
	REG_SOFTWARE_LOCK = 0xef,
	REG_PRODUCT_FEATURES = 0xfc,
	REG_PRODUCT_ID = 0xfd,
	REG_MANUFACTURER_ID = 0xfe,
	REG_REVISION = 0xff
};

/*
 * fan specific registers
 */
enum {
	REG_FAN_SETTING = 0x30,
	REG_PWM_DIVIDE = 0x31,
	REG_FAN_CONFIGURATION_1 = 0x32,
	REG_FAN_CONFIGURATION_2 = 0x33,
	REG_GAIN = 0x35,
	REG_FAN_SPIN_UP_CONFIG = 0x36,
	REG_FAN_MAX_STEP = 0x37,
	REG_FAN_MINIMUM_DRIVE = 0x38,
	REG_FAN_VALID_TACH_COUNT = 0x39,
	REG_FAN_DRIVE_FAIL_BAND_LOW = 0x3a,
	REG_FAN_DRIVE_FAIL_BAND_HIGH = 0x3b,
	REG_TACH_TARGET_LOW = 0x3c,
	REG_TACH_TARGET_HIGH = 0x3d,
	REG_TACH_READ_HIGH = 0x3e,
	REG_TACH_READ_LOW = 0x3f,
};

#define SEL_FAN(fan, reg) (reg + fan * 0x10)

/*
 * Factor by equations [2] and [3] from data sheet; valid for fans where the
 * number of edges equals (poles * 2 + 1).
 */
#define FAN_RPM_FACTOR 3932160


struct emc2305_fan_data {
	bool		enabled;
	bool		valid;
	unsigned long	last_updated;
	bool		rpm_control;
	u8		multiplier;
	u8		poles;
	u16		target;
	u16		tach;
	u16		rpm_factor;
	u8		pwm;
};

struct emc2305_data {
	struct device		*hwmon_dev;
	struct mutex		update_lock;
	int			fans;
	struct emc2305_fan_data	fan[5];
};

static int read_u8_from_i2c(struct i2c_client *client, u8 i2c_reg, u8 *output)
{
	int status = i2c_smbus_read_byte_data(client, i2c_reg);
	if (status < 0) {
		dev_warn(&client->dev, "reg 0x%02x, err %d\n",
			i2c_reg, status);
	} else {
		*output = status;
	}
	return status;
}

static void read_fan_from_i2c(struct i2c_client *client, u16 *output,
			      u8 hi_addr, u8 lo_addr)
{
	u8 high_byte, lo_byte;

	if (read_u8_from_i2c(client, hi_addr, &high_byte) < 0)
		return;

	if (read_u8_from_i2c(client, lo_addr, &lo_byte) < 0)
		return;

	*output = ((u16)high_byte << 5) | (lo_byte >> 3);
}

static void write_fan_target_to_i2c(struct i2c_client *client, int fan,
				    u16 new_target)
{
	const u8 lo_reg = SEL_FAN(fan, REG_TACH_TARGET_LOW);
	const u8 hi_reg = SEL_FAN(fan, REG_TACH_TARGET_HIGH);
	u8 high_byte = (new_target & 0x1fe0) >> 5;
	u8 low_byte = (new_target & 0x001f) << 3;
	i2c_smbus_write_byte_data(client, lo_reg, low_byte);
	i2c_smbus_write_byte_data(client, hi_reg, high_byte);
}

static void read_fan_config_from_i2c(struct i2c_client *client, int fan)

{
	struct emc2305_data *data = i2c_get_clientdata(client);
	u8 conf1;

	if (read_u8_from_i2c(client, SEL_FAN(fan, REG_FAN_CONFIGURATION_1),
			     &conf1) < 0)
		return;

	data->fan[fan].rpm_control = (conf1 & 0x80) != 0;
	data->fan[fan].multiplier = 1 << ((conf1 & 0x60) >> 5);
	data->fan[fan].poles = ((conf1 & 0x18) >> 3) + 1;
}

static void read_fan_setting(struct i2c_client *client, int fan)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	u8 setting;

	if (read_u8_from_i2c(client, SEL_FAN(fan, REG_FAN_SETTING),
			     &setting) < 0)
		return;

	data->fan[fan].pwm = setting;
}

static void read_fan_data(struct i2c_client *client, int fan_idx)
{
	struct emc2305_data *data = i2c_get_clientdata(client);

	read_fan_from_i2c(client, &data->fan[fan_idx].target,
			  SEL_FAN(fan_idx, REG_TACH_TARGET_HIGH),
			  SEL_FAN(fan_idx, REG_TACH_TARGET_LOW));
	read_fan_from_i2c(client, &data->fan[fan_idx].tach,
			  SEL_FAN(fan_idx, REG_TACH_READ_HIGH),
			  SEL_FAN(fan_idx, REG_TACH_READ_LOW));
}

static struct emc2305_fan_data *
emc2305_update_fan(struct i2c_client *client, int fan_idx)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	struct emc2305_fan_data *fan_data = &data->fan[fan_idx];

	mutex_lock(&data->update_lock);

	if (time_after(jiffies, fan_data->last_updated + HZ + HZ / 2)
	    || !fan_data->valid) {
		read_fan_config_from_i2c(client, fan_idx);
		read_fan_data(client, fan_idx);
		read_fan_setting(client, fan_idx);
		fan_data->valid = true;
		fan_data->last_updated = jiffies;
	}

	mutex_unlock(&data->update_lock);
	return fan_data;
}

static struct emc2305_fan_data *
emc2305_update_device_fan(struct device *dev, struct device_attribute *da)
{
	struct i2c_client *client = to_i2c_client(dev);
	int fan_idx = to_sensor_dev_attr(da)->index;

	return emc2305_update_fan(client, fan_idx);
}

/*
 * set/ config functions
 */

/*
 * Note: we also update the fan target here, because its value is
 * determined in part by the fan clock divider.  This follows the principle
 * of least surprise; the user doesn't expect the fan target to change just
 * because the divider changed.
 */
static int
emc2305_set_fan_div(struct i2c_client *client, int fan_idx, long new_div)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	struct emc2305_fan_data *fan = emc2305_update_fan(client, fan_idx);
	const u8 reg_conf1 = SEL_FAN(fan_idx, REG_FAN_CONFIGURATION_1);
	int new_range_bits, old_div = 8 / fan->multiplier;
	int status = 0;

	if (new_div == old_div) /* No change */
		return 0;

	switch (new_div) {
	case 1:
		new_range_bits = 3;
		break;
	case 2:
		new_range_bits = 2;
		break;
	case 4:
		new_range_bits = 1;
		break;
	case 8:
		new_range_bits = 0;
		break;
	default:
		return -EINVAL;
	}

	mutex_lock(&data->update_lock);

	status = i2c_smbus_read_byte_data(client, reg_conf1);
	if (status < 0) {
		dev_dbg(&client->dev, "reg 0x%02x, err %d\n",
			reg_conf1, status);
		status = -EIO;
		goto exit_unlock;
	}
	status &= 0x9F;
	status |= (new_range_bits << 5);
	status = i2c_smbus_write_byte_data(client, reg_conf1, status);
	if (status < 0) {
		status = -EIO;
		goto exit_invalidate;
	}

	fan->multiplier = 8 / new_div;

	/* update fan target if high byte is not disabled */
	if ((fan->target & 0x1fe0) != 0x1fe0) {
		u16 new_target = (fan->target * old_div) / new_div;
		fan->target = min_t(u16, new_target, 0x1fff);
		write_fan_target_to_i2c(client, fan_idx, fan->target);
	}

exit_invalidate:
	/* invalidate fan data to force re-read from hardware */
	fan->valid = false;
exit_unlock:
	mutex_unlock(&data->update_lock);
	return status;
}

static int
emc2305_set_fan_target(struct i2c_client *client, int fan_idx, long rpm_target)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	struct emc2305_fan_data *fan = emc2305_update_fan(client, fan_idx);

	/*
	 * Datasheet states 16000 as maximum RPM target
	 * (table 2.2 and section 4.3)
	 */
	if ((rpm_target < 0) || (rpm_target > 16000))
		return -EINVAL;

	mutex_lock(&data->update_lock);

	if (rpm_target == 0)
		fan->target = 0x1fff;
	else
		fan->target = clamp_val(
			(FAN_RPM_FACTOR * fan->multiplier) / rpm_target,
			0, 0x1fff);

	write_fan_target_to_i2c(client, fan_idx, fan->target);

	mutex_unlock(&data->update_lock);
	return 0;
}

static int
emc2305_set_pwm_enable(struct i2c_client *client, int fan_idx, long enable)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	struct emc2305_fan_data *fan = emc2305_update_fan(client, fan_idx);
	const u8 reg_fan_conf1 = SEL_FAN(fan_idx, REG_FAN_CONFIGURATION_1);
	int status = 0;
	u8 conf_reg;

	mutex_lock(&data->update_lock);
	switch (enable) {
	case 0:
		fan->rpm_control = false;
		break;
	case 3:
		fan->rpm_control = true;
		break;
	default:
		status = -EINVAL;
		goto exit_unlock;
	}

	status = read_u8_from_i2c(client, reg_fan_conf1, &conf_reg);
	if (status < 0) {
		status = -EIO;
		goto exit_unlock;
	}

	if (fan->rpm_control)
		conf_reg |= 0x80;
	else
		conf_reg &= ~0x80;

	status = i2c_smbus_write_byte_data(client, reg_fan_conf1, conf_reg);
	if (status < 0)
		status = -EIO;

exit_unlock:
	mutex_unlock(&data->update_lock);
	return status;
}

static int
emc2305_set_pwm(struct i2c_client *client, int fan_idx, long pwm)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	struct emc2305_fan_data *fan = emc2305_update_fan(client, fan_idx);
	const u8 reg_fan_setting = SEL_FAN(fan_idx, REG_FAN_SETTING);
	int status = 0;

	/*
	 * Datasheet states 255 as maximum PWM
	 * (section 5.7)
	 */
	if ((pwm < 0) || (pwm > 255))
		return -EINVAL;

	fan->pwm = pwm;

	mutex_lock(&data->update_lock);

	status = i2c_smbus_write_byte_data(client, reg_fan_setting, fan->pwm);

	mutex_unlock(&data->update_lock);
	return status;
}
/*
 * sysfs callback functions
 *
 * Note:
 * Naming of the funcs is modelled after the naming scheme described in
 * Documentation/hwmon/sysfs-interface:
 *
 * For a sysfs file <type><number>_<item> the functions are named like this:
 *    the show function: show_<type>_<item>
 *    the store function: set_<type>_<item>
 * For read only (RO) attributes of course only the show func is required.
 *
 * This convention allows us to define the sysfs attributes by using macros.
 */

static ssize_t
show_fan_input(struct device *dev, struct device_attribute *da, char *buf)
{
	struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
	int rpm = 0;
	if (fan->tach != 0)
		rpm = (FAN_RPM_FACTOR * fan->multiplier) / fan->tach;
	return sprintf(buf, "%d\n", rpm);
}

static ssize_t
show_fan_fault(struct device *dev, struct device_attribute *da, char *buf)
{
	struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
	bool fault = ((fan->tach & 0x1fe0) == 0x1fe0);
	return sprintf(buf, "%d\n", fault ? 1 : 0);
}

static ssize_t
show_fan_div(struct device *dev, struct device_attribute *da, char *buf)
{
	struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
	int fan_div = 8 / fan->multiplier;
	return sprintf(buf, "%d\n", fan_div);
}

static ssize_t
show_fan_alarm(struct device *dev, struct device_attribute *da, char *buf)
{
	struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
	bool fault = ((fan->tach & 0x1fe0) == 0x1fe0);
	return sprintf(buf, "%d\n", fault ? 1 : 0);
}

static ssize_t
set_fan_div(struct device *dev, struct device_attribute *da,
	    const char *buf, size_t count)
{
	struct i2c_client *client = to_i2c_client(dev);
	int fan_idx = to_sensor_dev_attr(da)->index;
	long new_div;
	int status;

	status = kstrtol(buf, 10, &new_div);
	if (status < 0)
		return -EINVAL;

	status = emc2305_set_fan_div(client, fan_idx, new_div);
	if (status < 0)
		return status;

	return count;
}

static ssize_t
show_fan_target(struct device *dev, struct device_attribute *da, char *buf)
{
	struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
	int rpm = 0;

	/* high byte of 0xff indicates disabled so return 0 */
	if ((fan->target != 0) && ((fan->target & 0x1fe0) != 0x1fe0))
		rpm = (FAN_RPM_FACTOR * fan->multiplier)
			/ fan->target;

	return sprintf(buf, "%d\n", rpm);
}

static ssize_t set_fan_target(struct device *dev, struct device_attribute *da,
			      const char *buf, size_t count)
{
	struct i2c_client *client = to_i2c_client(dev);
	int fan_idx = to_sensor_dev_attr(da)->index;
	long rpm_target;
	int status;

	status = kstrtol(buf, 10, &rpm_target);
	if (status < 0)
		return -EINVAL;

	status = emc2305_set_fan_target(client, fan_idx, rpm_target);
	if (status < 0)
		return status;

	return count;
}

static ssize_t
show_pwm_enable(struct device *dev, struct device_attribute *da, char *buf)
{
	struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
	return sprintf(buf, "%d\n", fan->rpm_control ? 3 : 0);
}

static ssize_t set_pwm_enable(struct device *dev, struct device_attribute *da,
			      const char *buf, size_t count)
{
	struct i2c_client *client = to_i2c_client(dev);
	int fan_idx = to_sensor_dev_attr(da)->index;
	long new_value;
	int status;

	status = kstrtol(buf, 10, &new_value);
	if (status < 0)
		return -EINVAL;
	status = emc2305_set_pwm_enable(client, fan_idx, new_value);
	return count;
}

static ssize_t show_pwm(struct device *dev, struct device_attribute *da,
			char *buf)
{
	struct emc2305_fan_data *fan = emc2305_update_device_fan(dev, da);
	return sprintf(buf, "%d\n", fan->pwm);
}

static ssize_t set_pwm(struct device *dev, struct device_attribute *da,
		       const char *buf, size_t count)
{
	struct i2c_client *client = to_i2c_client(dev);
	int fan_idx = to_sensor_dev_attr(da)->index;
	unsigned long val;
	int ret;
	int status;

	ret = kstrtoul(buf, 10, &val);
	if (ret)
		return ret;
	if (val > 255)
		return -EINVAL;

	status = emc2305_set_pwm(client, fan_idx, val);
	return count;
}

/* define a read only attribute */
#define EMC2305_ATTR_RO(_type, _item, _num)			\
	SENSOR_ATTR(_type ## _num ## _ ## _item, S_IRUGO,	\
		    show_## _type ## _ ## _item, NULL, _num - 1)

/* define a read/write attribute */
#define EMC2305_ATTR_RW(_type, _item, _num)				\
	SENSOR_ATTR(_type ## _num ## _ ## _item, S_IRUGO | S_IWUSR,	\
		    show_## _type ##_ ## _item,				\
		    set_## _type ## _ ## _item, _num - 1)

/*
 * TODO: Ugly hack, but temporary as this whole logic needs
 * to be rewritten as per standard HWMON sysfs registration
 */

/* define a read/write attribute */
#define EMC2305_ATTR_RW2(_type, _num)				\
	SENSOR_ATTR(_type ## _num, S_IRUGO | S_IWUSR,	\
		    show_## _type, set_## _type, _num - 1)

/* defines the attributes for a single fan */
#define EMC2305_DEFINE_FAN_ATTRS(_num)					\
	static const							\
	struct sensor_device_attribute emc2305_attr_fan ## _num[] = {	\
		EMC2305_ATTR_RO(fan, input, _num),			\
		EMC2305_ATTR_RO(fan, fault, _num),			\
		EMC2305_ATTR_RW(fan, div, _num),			\
		EMC2305_ATTR_RO(fan, alarm, _num),			\
		EMC2305_ATTR_RW(fan, target, _num),			\
		EMC2305_ATTR_RW(pwm, enable, _num),			\
		EMC2305_ATTR_RW2(pwm, _num)			\
	}

#define EMC2305_NUM_FAN_ATTRS ARRAY_SIZE(emc2305_attr_fan1)

/* common attributes for EMC2303 and EMC2305 */
static const struct sensor_device_attribute emc2305_attr_common[] = {
};

/* fan attributes for the single fans */
EMC2305_DEFINE_FAN_ATTRS(1);
EMC2305_DEFINE_FAN_ATTRS(2);
EMC2305_DEFINE_FAN_ATTRS(3);
EMC2305_DEFINE_FAN_ATTRS(4);
EMC2305_DEFINE_FAN_ATTRS(5);
EMC2305_DEFINE_FAN_ATTRS(6);

/* fan attributes */
static const struct sensor_device_attribute *emc2305_fan_attrs[] = {
	emc2305_attr_fan1,
	emc2305_attr_fan2,
	emc2305_attr_fan3,
	emc2305_attr_fan4,
	emc2305_attr_fan5,
};

/*
 * driver interface
 */

static int emc2305_remove(struct i2c_client *client)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	int fan_idx, i;

	hwmon_device_unregister(data->hwmon_dev);

	for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
		for (i = 0; i < EMC2305_NUM_FAN_ATTRS; ++i)
			device_remove_file(
				&client->dev,
				&emc2305_fan_attrs[fan_idx][i].dev_attr);

	for (i = 0; i < ARRAY_SIZE(emc2305_attr_common); ++i)
		device_remove_file(&client->dev,
				   &emc2305_attr_common[i].dev_attr);

	kfree(data);
	return 0;
}


#ifdef CONFIG_OF
/*
 * device tree support
 */

struct of_fan_attribute {
	const char *name;
	int (*set)(struct i2c_client*, int, long);
};

struct of_fan_attribute of_fan_attributes[] = {
	{"fan-div", emc2305_set_fan_div},
	{"fan-target", emc2305_set_fan_target},
	{"pwm-enable", emc2305_set_pwm_enable},
	{NULL, NULL}
};

static int emc2305_config_of(struct i2c_client *client)
{
	struct emc2305_data *data = i2c_get_clientdata(client);
	struct device_node *node;
	unsigned int fan_idx;

	if (!client->dev.of_node)
		return -EINVAL;
	if (!of_get_next_child(client->dev.of_node, NULL))
		return  0;

	for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
		data->fan[fan_idx].enabled = false;

	for_each_child_of_node(client->dev.of_node, node) {
		const __be32 *property;
		int len;
		struct of_fan_attribute *attr;

		property = of_get_property(node, "reg", &len);
		if (!property || len != sizeof(int)) {
			dev_err(&client->dev, "invalid reg on %s\n",
				node->full_name);
			continue;
		}

		fan_idx = be32_to_cpup(property);
		if (fan_idx >= data->fans) {
			dev_err(&client->dev,
				"invalid fan index %d on %s\n",
				fan_idx, node->full_name);
			continue;
		}

		data->fan[fan_idx].enabled = true;

		for (attr = of_fan_attributes; attr->name; ++attr) {
			int status = 0;
			long value;
			property = of_get_property(node, attr->name, &len);
			if (!property)
				continue;
			if (len != sizeof(int)) {
				dev_err(&client->dev, "invalid %s on %s\n",
					attr->name, node->full_name);
				continue;
			}
			value = be32_to_cpup(property);
			status = attr->set(client, fan_idx, value);
			if (status == -EINVAL) {
				dev_err(&client->dev,
					"invalid value for %s on %s\n",
					attr->name, node->full_name);
			}
		}
	}

	return 0;
}

#endif

static void emc2305_get_config(struct i2c_client *client)
{
	int i;
	struct emc2305_data *data = i2c_get_clientdata(client);

	for (i = 0; i < data->fans; ++i) {
		data->fan[i].enabled = true;
		emc2305_update_fan(client, i);
	}

#ifdef CONFIG_OF
	emc2305_config_of(client);
#endif

}

static int
emc2305_probe(struct i2c_client *client, const struct i2c_device_id *id)
{
	struct emc2305_data *data;
	int status;
	int i;
	int fan_idx;
	unsigned char dis_to = 0;

	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
		return -EIO;

	data = kzalloc(sizeof(struct emc2305_data), GFP_KERNEL);
	if (!data)
		return -ENOMEM;

	i2c_set_clientdata(client, data);
	mutex_init(&data->update_lock);
	
	dis_to = i2c_smbus_read_byte_data(client, REG_CONFIGURATION);
	dis_to &= 0xBF;
	/* The SMBus timeout function is enabled */
	(void)i2c_smbus_write_byte_data(client, REG_CONFIGURATION, dis_to);

	status = i2c_smbus_read_byte_data(client, REG_PRODUCT_ID);
	switch (status) {
	case 0x34: /* EMC2305 */
		data->fans = 5;
		break;
	case 0x35: /* EMC2303 */
		data->fans = 3;
		break;
	case 0x36: /* EMC2302 */
		data->fans = 2;
		break;
	case 0x37: /* EMC2301 */
		data->fans = 1;
		break;
	default:
		if (status >= 0)
			status = -EINVAL;
		goto exit_free;
	}

	emc2305_get_config(client);

	for (i = 0; i < ARRAY_SIZE(emc2305_attr_common); ++i) {
		status = device_create_file(&client->dev,
					    &emc2305_attr_common[i].dev_attr);
		if (status)
			goto exit_remove;
	}
	for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
		for (i = 0; i < EMC2305_NUM_FAN_ATTRS; ++i) {
			if (!data->fan[fan_idx].enabled)
				continue;
			status = device_create_file(
				&client->dev,
				&emc2305_fan_attrs[fan_idx][i].dev_attr);
			if (status)
				goto exit_remove_fans;
		}

	data->hwmon_dev = hwmon_device_register(&client->dev);
	if (IS_ERR(data->hwmon_dev)) {
		status = PTR_ERR(data->hwmon_dev);
		goto exit_remove_fans;
	}

	dev_info(&client->dev, "%s: sensor '%s'\n",
		 dev_name(data->hwmon_dev), client->name);

	return 0;

exit_remove_fans:
	for (fan_idx = 0; fan_idx < data->fans; ++fan_idx)
		for (i = 0; i < EMC2305_NUM_FAN_ATTRS; ++i)
			device_remove_file(
				&client->dev,
				&emc2305_fan_attrs[fan_idx][i].dev_attr);

exit_remove:
	for (i = 0; i < ARRAY_SIZE(emc2305_attr_common); ++i)
		device_remove_file(&client->dev,
				   &emc2305_attr_common[i].dev_attr);
exit_free:
	kfree(data);
	return status;
}

static const struct i2c_device_id emc2305_id[] = {
	{ "emc2305", 0 },
	{ "emc2303", 0 },
	{ "emc2302", 0 },
	{ "emc2301", 0 },
	{ }
};
MODULE_DEVICE_TABLE(i2c, emc2305_id);

/* Return 0 if detection is successful, -ENODEV otherwise */
static int
emc2305_detect(struct i2c_client *new_client, struct i2c_board_info *info)
{
	struct i2c_adapter *adapter = new_client->adapter;
	int manufacturer, product;

	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
		return -ENODEV;

	manufacturer =
		i2c_smbus_read_byte_data(new_client, REG_MANUFACTURER_ID);
	if (manufacturer != 0x5D)
		return -ENODEV;

	product = i2c_smbus_read_byte_data(new_client, REG_PRODUCT_ID);

	switch (product) {
	case 0x34:
		strlcpy(info->type, "emc2305", I2C_NAME_SIZE);
		break;
	case 0x35:
		strlcpy(info->type, "emc2303", I2C_NAME_SIZE);
		break;
	case 0x36:
		strlcpy(info->type, "emc2302", I2C_NAME_SIZE);
		break;
	case 0x37:
		strlcpy(info->type, "emc2301", I2C_NAME_SIZE);
		break;
	default:
		return -ENODEV;
	}

	return 0;
}

static struct i2c_driver emc2305_driver = {
	.class		= I2C_CLASS_HWMON,
	.driver = {
		.name	= "emc2305",
	},
	.probe		= emc2305_probe,
	.remove		= emc2305_remove,
	.id_table	= emc2305_id,
/*
	.detect		= emc2305_detect,
	.address_list	= i2c_adresses,
*/
};

module_i2c_driver(emc2305_driver);

MODULE_AUTHOR("Reinhard Pfau <pfau@gdsys.de>");
MODULE_DESCRIPTION("SMSC EMC2305 hwmon driver");
MODULE_LICENSE("GPL");