26afa348ea
* Update sensors.conf for 7050QX-32 and 7050QX-32S These two platforms were using a previous version of a kernel driver. The new one names the i2c buses differently. We therefore need to rename them here. * Fix the default minigraph for the 7050QX-32S The interface offset is invalid which makes sonic-cfggen generate an invalid config_db.jon in rc.local. This config then silently makes orchagent/syncd fail. * Use the partition on which sonic-aboot.swi is Instead of always assuming /mnt/flash, use the partition where the image to be installed lies. This allow for the image to be on any partition.
83 lines
2.0 KiB
Plaintext
83 lines
2.0 KiB
Plaintext
# libsensors configuration file for DCS-7050QX-32
|
|
# ------------------------------------------------
|
|
#
|
|
|
|
bus "i2c-2" "SCD 0000:04:00.0 SMBus master 0 bus 0"
|
|
bus "i2c-3" "SCD 0000:04:00.0 SMBus master 0 bus 1"
|
|
bus "i2c-5" "SCD 0000:04:00.0 SMBus master 0 bus 3"
|
|
bus "i2c-6" "SCD 0000:04:00.0 SMBus master 0 bus 4"
|
|
bus "i2c-7" "SCD 0000:04:00.0 SMBus master 0 bus 5"
|
|
|
|
chip "k10temp-pci-00c3"
|
|
label temp1 "Cpu temp sensor"
|
|
|
|
chip "lm73-i2c-3-48"
|
|
label temp1 "Back panel temp sensor"
|
|
set temp1_max 65
|
|
#set temp1_max_alarm 75 # read-only
|
|
|
|
chip "max6658-i2c-2-4c"
|
|
label temp1 "Board temp sensor"
|
|
set temp1_max 65
|
|
set temp1_crit 75
|
|
|
|
label temp2 "Front panel temp sensor"
|
|
set temp2_max 65
|
|
set temp2_crit 75
|
|
|
|
# disabled because of some eeprom corruption risks
|
|
#chip "pmbus-i2c-3-4e"
|
|
# label temp1 "Power controller sensor 1"
|
|
# set temp1_max 60
|
|
# set temp1_crit 70
|
|
|
|
# label temp2 "Power controller sensor 2"
|
|
# set temp2_max 60
|
|
# set temp2_crit 70
|
|
|
|
# ignore curr1
|
|
|
|
chip "dps460-i2c-5-58"
|
|
label temp1 "Power supply 1 inlet temp sensor"
|
|
# maximum and critical thresholds are not supported for this psu
|
|
set temp1_max 60
|
|
set temp1_crit 70
|
|
|
|
label temp2 "Power supply 1 internal sensor"
|
|
set temp2_max 60
|
|
set temp2_crit 70
|
|
|
|
ignore temp3
|
|
|
|
set in1_max 250
|
|
set in1_crit 255
|
|
set power1_max 525
|
|
set power2_max 460
|
|
set power2_crit 462
|
|
set curr1_max 5.28
|
|
set curr1_crit 5.30
|
|
set curr2_max 36
|
|
set curr2_crit 37
|
|
|
|
chip "dps460-i2c-6-58"
|
|
label temp1 "Power supply 2 inlet temp sensor"
|
|
# maximum and critical thresholds are not supported for this psu
|
|
set temp1_max 60
|
|
set temp1_crit 70
|
|
|
|
label temp2 "Power supply 2 internal sensor"
|
|
set temp2_max 60
|
|
set temp2_crit 70
|
|
|
|
ignore temp3
|
|
|
|
set in1_max 250
|
|
set in1_crit 255
|
|
set power1_max 525
|
|
set power2_max 460
|
|
set power2_crit 462
|
|
set curr1_max 5.28
|
|
set curr1_crit 5.30
|
|
set curr2_max 36
|
|
set curr2_crit 37
|