- Why I did it
ethtool is not able to read certain pages(eg. page 11h) of CMIS cables.
SDK provides a set of sysfs to expose the transceiver EEPROM, now we migrate from using ethtool to read these sysfs for transceiver EEPROM reading.
- How I did it
replace ethtool with accessing the SDK sysfs for cable EEPROM reading.
Adjust the offset according to the SDK sysfs memory map.
- How to verify it
run sonic-mgmt sfp-related regression test case.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- Why I did it
Update SDK/FW version - 4.5.3186/2010_3186 in order to have the following changes:
New functionality:
1. Added support for 6.5W (Class 8) in ports 49-50, 53-54, 57-58, and 61-62 on SN4600 system
Fix the following issues:
1. On very rare occasion (~1/100K), during I2C transaction with MMS1V50-WM and MMS1V90-WR modules on SN4700 system, the module may send unexpected stop which violate the I2C specification, possibly affecting the link up flow
2. When running 1GbE speeds on SN4600 system, the port remained active while peer side was closed
3. While toggling the cable with ‘sfputil lpmode on/off’, error msg like “ERR pmon#xcvrd: Receive PMPE error event on module 1: status {X} error type {y}” could be received
4. When toggling many ports of the Spectrum devices while raising 10GbE link up and link maintenance is enabled, the switch may get stuck and may need to be rebooted
5. When trying to reconfigure the Flex Parser header and Flex transition parameters after ISSU, the switch will returned an error even if the configuration was identical to that done before performing the ISSU
6. While moving from lossless to lossy mode while shared headroom was used, reduction of the shared headroom can only be done prior to pool type change and when shared headroom is not utilized
7. SLL configuration is missing in SDK dump
8. If TTL_CMD_COPY is used in Encap direction for a packet with no TTL, then the value passed in the ttl data structure will be used if non-zero (default 255 if zero)
9. PCI calibration changes from a static to a dynamic mechanism
10. Layer 4 port information is not initialized for BFD packet event. To address the issue, remote peer UDP port information was added in BFD packet event
11. SDK returned error when FEC mode is set on twisted pair, when FEC was set to None
- How I did it
Update pointer for the SDK/FW
- How to verify it
Run regression tests
Signed-off-by: dprital <drorp@nvidia.com>
* [TestbedV2]Migrate t0 and t1-lag to TestbedV2 (#12383)
signed-off-by: jianquanye@microsoft.com
Migrate the t0 and t1-lag test jobs in buildimage repo to TestbedV2.
Why I did it
Migrate the t0 and t1-lag test jobs in buildimage repo to TestbedV2.
How I did it
Migrate the t0 and t1-lag test jobs in buildimage repo to TestbedV2.
Remove ceos type setting
Use 202012 branch as sonic-mgmt branch
* Modify template to use 202012 branch
Update sonic-swss submodule pointer to include the following:
* 08711a8 [orchdaemon]: Fixed sairedis record file rotation ([#2481](https://github.com/sonic-net/sonic-swss/pull/2481))
Signed-off-by: dprital <drorp@nvidia.com>
* Fix to improve hostname handling
If config_db.json is missing hostname entry, hostname-config.sh ends
up deleting existing entry too and hostname changes to default 'localhost'
* default hostname to 'sonic` if missing in config file
- Skip the interface status check if the interface does not exist. In the future, when the interface is created/comes up this check will be triggered again.
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
Why I did it
Cherry pick #9519.
when we remove a port and add it back immediately - lldp is keep failing
warning message keeps appearing:
[WARN/lldp] unable to send packet on real device for Ethernet4: No such device or address
How I did it
on delete link events it will immediately execute delete without using aggregate events mechanism.
How to verify it
Run autorestart/test_container_autorestart.py in sonic-mgmt repo
Or manual test steps:
sudo config feature autorestart swss disabled
docker exec swss supervisorctl status
docker exec swss kill -SIGKILL 111(orchagent)
docker inspect -f {{.State.Running}} swss => make sure swss is running
docker exec swss supervisorctl start orchagent
Signed-off-by: Zhaohui Sun <zhaohuisun@microsoft.com>
Why I did it
Cherry-pick from #8950
Sonic-swss-common requires gmock for staged unit tests
How I did it
Installed dependency in sonic-buster-build docker file
How to verify it
rebuild the build container
Why I did it
Change the path of sonic submodules that point to "Azure" to point to "sonic-net"
How I did it
Replace "Azure" with "sonic-net" on all relevant paths of sonic submodules
New SKU for MSN-4700 Platform i.e. Mellanox-SN4700-C128
Requirements:
* Breakout: Port 1-32: 4x100G
* Downlinks: 120 (1-30)
* Uplinks: 8 (31-32)
* Shared Headroom: Enabled
* Over Subscribe Ratio: 1:8
* Default Topology: T2
* Default Cable Length for T2: 1500m
* QoS params: The default ones defined in qos_config.j2 will be applied
* Small Packet Percentage: Used 50% for traditional buffer model Note: For dynamic model, the value defined in LOSSLESS_TRAFFIC_PATTERN|AZURE|small_packet_percentage is used
Additional Details:
Switch Type has to be programmed as SpineRouter through config_db.json in DEVICE_METADATA|localhost|type field for the buffer values & cable lengths defined in the buffers_defaults_t2.j2 to apply on the device
Cable Lengths Used for generating buffer_defaults_{t0,t1,t2}.j2
Signed-off-by: Vivek Reddy Karri <vkarri@nvidia.com>
A new SKU for MSN4700 Platform i.e. Mellanox-SN4700-A96C8V8
Requirements:
Breakout:
Port 1-24: 4x25G(4)[10G,1G]
Port 25-28: 2x100G[200G,50G,40G,25G,10G,1G]
Port 29-32: 2x200G[100G,50G,40G,25G,10G,1G]
Downlinks: 96 (1-24) + 4 (25-28)
Uplinks: 4 (29-32)
Shared Headroom: Enabled
Over Subscribe Ratio: 1:4
Default Topology: T0
Default Cable Length for T1: 5m
VxLAN source port range set: No
Static Policy Based Hashing Supported: No
Additional Details:
QoS params: The default ones defined in qos_config.j2 will be applied
Small Packet Percentage: Used 50% for traditional buffer model Note: For dynamic model, the value defined in LOSSLESS_TRAFFIC_PATTERN|AZURE|small_packet_percentage is used
SKU was drafted under the assumption that the downlink ports uses xcvr's that will only support the first 4 lanes of the physical port they are connected to. Hence for the ports 1-24, the last four lanes are not used
Cable Lengths used for generating buffer_defaults_{t0,t1}.j2 D
Signed-off-by: Vivek Reddy <vkarri@nvidia.com>
- Why I did it
Fixes#11431
- How I did it
dhcp6relay binds to ipv6 addresses configured on these vlan interfaces
Thus check if they are ready before launching dhcp6relay
- How to verify it
Unit Tests
Tested on a live device
Signed-off-by: Vivek Reddy Karri <vkarri@nvidia.com>
