- Why I did it
Optimize syslog rate limit feature for fast and warm boot
- How I did it
Optimize redis start time
Don't render rsyslog.conf in container startup script
Disable containercfgd by default. There is a new CLI to enable it (in another PR)
- How to verify it
Manual test
Regression test
Why I did it
Each release branch needs to have release number set.
Work item tracking
Microsoft ADO (number only):
How I did it
How to verify it
This PR test.
- Why I did it
Mellanox MSN2410 platforms have a non-functional error log: "ERR pmon#sensord: Error getting sensor data: dps460/#10: Can't read". This error is because of a firmware issue with some PSU, we are not able to upgrade the FW online. Since there is no functional impact, this error log can be ignored safely
- How I did it
Add a new rsyslog rule to the rsyslog-container.conf.j2, if the docker name is pmon and the platform name matches, the new rule will be inserted into the docker rsyslogd.conf
- How to verify it
run regression on the MSN2410 platform to make the error log will not be printed to the syslog.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
[arp_update]: Flush MAC mismatch neighbors
- Check for MAC mismatch between neighbor entries in the kernel and APPL_DB
- Flush any entries with a mismatch
Change DHCP rate limit in SONiC copp configuration to 100 PPS as this is
necessary to ensure that DHCP flood does not cause LACP/BGP flaps in all
scenarios
This is an extension to the change in image_config: copp: Enable rate limiting
for bgp, lacp, dhcp, lldp, macsec and udld #14859 and sonic-mgmt change in
[tests/copp]: Update copp mgmt tests to support new rate-limits sonic-mgmt#8199
Why I did it
300 PPS is not sufficient to prevent LACP/BGP flaps in all cases. 100 PPS seems to
provide better resiliency against DHCP traffic flood to CPU.
Microsoft ADO 25776614:
Send DHCP broadcast packets to DUT and verify that they are trapped to CPU at 100 PPS.
Signed-off-by: Prabhat Aravind <paravind@microsoft.com>
What I did:
In Chassis TSA mode Loopback0 Ip's of each LC's should be advertise through e-BGP peers of each remote LC's
How I did:
- Route-map policy to Advertise own/self Loopback IP to other internal iBGP peers with a community internal_community as define in constants.yml
- Route-map policy to match on above internal_community when route is received from internal iBGP peers and set a internal tag as define in constants.yml and also delete the internal_community so we don't send to any of e-BGP peers
- In TSA new route-map match on above internal tag and permit the route (Loopback0 IP's of remote LC's) and set the community to traffic_shift_community.
- In TSB delete the above new route-map.
How I verify:
Manual Verification
UT updated.
sonic-mgmt PR: sonic-net/sonic-mgmt#10239
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
Sub PRs:
sonic-net/sonic-host-services#84
#17191
Why I did it
According to the design, the database instances of DPU will be kept in the NPU host.
Microsoft ADO (number only): 25072889
How I did it
To follow the multiple ASIC design, I assume a new platform environment variable NUM_DPU will be defined in the /usr/share/sonic/device/$PLATFORM/platform_env.conf. Based on this number, NPU host will launch a corresponding number of instances for the DPU database.
Signed-off-by: Ze Gan <ganze718@gmail.com>
Why I did it
Share docker image to support gnmi container and telemetry container
Work item tracking
Microsoft ADO 25423918:
How I did it
Create telemetry image from gnmi docker image.
Enable gnmi container and disable telemetry container by default.
How to verify it
Run end to end test.
Why I did it
It was observed that a flood of DHCP packets without rate-limiting can cause BGP flaps or lacp keepalive losses.
This change attempts to prevent or reduce such BGP flaps by enabling appropriate rate-limiting in SONiC for all traffic types.
Work item tracking
Microsoft ADO 17964421:
How I did it
Set a reasonable CIR/CBS value of 300 for queue4_group3 (dhcp, lldp, macsec) and 6000 for queue4_group1.
The value 300 was arrived at after testing with dhcp flooding using ptf (using multiple threads). Throttling at this rate was necessary to ensure that dhcp flooding does not cause BGP flaps.
How to verify it
Verified with this script running from ptf, that BGP flaps don't happen when CBS/CIR is set at 300 for queue4_group3.
import threading
from scapy.all import *
def send_dhcp_discover(intf):
dhcp_discover = Ether(dst='ff:ff:ff:ff:ff:ff',src=RandMAC()) \
/IP(src='1.1.1.1',dst='255.255.255.255') \
/UDP(sport=68,dport=67) \
/DHCP(options=[('message-type','discover'),('end')])
sendp(dhcp_discover,count=100000,iface=intf)
if __name__ == "__main__":
t1 = threading.Thread(target=send_dhcp_discover, args=("eth1",))
t2 = threading.Thread(target=send_dhcp_discover, args=("eth2",))
t1.start()
t2.start()
t1.join()
t2.join()
Verified on Arista-7260CX3-D108C8 running 202012 that the copp rule for queue4_group1 and queue4_group3 do NOT affect BGP packets. To verify this using PTF, the copp rules were modified to set the "CBS" and "CIR" for queue4_group1 and queue4_group3 at 600pps and 50k packets each of "BGP open" and "DHCP Discover" were simultaneously sent from the same PTF port to the DUT. It was verified using "show c cpu" that packets are hitting the cpu queue at 1200 pps (double the configured CIR/CBS for these packet types). This helped conclude that throttling rate is per trap (or packet type) and not per queue.
Verified with updated sonic-mgmt tests ([tests/copp]: Update copp mgmt tests to support new rate-limits sonic-mgmt#8199) on broadcom and mellanox platforms that these traffic types are rate-limited.
Signed-off-by: Prabhat Aravind <paravind@microsoft.com>
- Why I did it
Mellanox MSN2700 platforms have a non-functional error log: "ERR pmon#sensord: Error getting sensor data: dps460/#10: Can't read". This error is because of a firmware issue with some PSU, we are not able to upgrade the FW online. Since there is no functional impact, this error log can be ignored safely.
- How I did it
Add a new rsyslog rule to the rsyslog-container.conf.j2, if the docker name is pmon and the platform name matches, the new rule will be inserted into the docker rsyslogd.conf
- How to verify it
run regression on the MSN2700 platform to make the error log will not be printed to the syslog.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
* Reduce SONiC image filesystem size
Add a build option to reduce the image size.
The image reduction process is affecting the builds in 2 ways:
- change some packages that are installed in the rootfs
- apply a rootfs reduction script
The script itself will perform a few steps:
- remove file duplication by leveraging hardlinks
- under /usr/share/sonic since the symlinks under the device folder are lost during the build.
- under /var/lib/docker since the files there will only be mounted ro
- remove some extra files (man, docs, licenses, ...)
- some image specific space reduction (only for aboot images currently)
The script can later be improved but for now it's reducing the rootfs
size by ~30%.
* restore fully featured vim package
Why I did it
Networking devices need to be responsive. Such responsiveness is harmed when the CPU change state.
There is a latency penalty when a CPU is idle (e.g C2) and need to exit this state to come back to C1 state.
To prevent this from happening the CPU should be forced to remain in C1 state.
How I did it
Generalize the cstate forcing to C1 to all Arista products.
This is done by adding processor.max_cstate=1 to the kernel cmdline for all CPUs.
Additionally Intel CPUs also need intel_idle.max_cstate=0 to fallback to the acpi_idle driver.
How to verify it
Check that processor.max_cstate=1 is present on the cmdline for AMD CPUs
Check that both processor.max_cstate=1 and intel_idle.max_cstate=0 are present on the cmdline for Intel CPUs
Openssh in Debian Bullseye has been updated to 1:8.4p1-5+deb11u2 to fix CVE-2023-38408.
Since we're building openssh with some patches, we need to update our version as well.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
* [buffers] Add create_only_config_db_buffers.json for MLNX devices (not MSFT SKU), inject it at the start of the swss docker
Signed-off-by: vadymhlushko-mlnx <vadymh@nvidia.com>
* [buffers] Align the sonic-device_metadata.yang
Signed-off-by: vadymhlushko-mlnx <vadymh@nvidia.com>
---------
Signed-off-by: vadymhlushko-mlnx <vadymh@nvidia.com>
Why I did it
Fix: #16699
Fast reboot is failing from old OS versions (eg., 201911 image) to latest (eg., master branch) after PR #15685
The system wide flag for FAST_REBOOT is still required when the base OS version does not support the new fast-reboot reconciliation logic (no db dump)
Add alternate name eth1-midplane to Linux bridge br1 created on supervisor on some chassis platforms.
See description here: #16504
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
Fix tcpdump report error when tacacs enabled.
Why I did it
Fix tcpdump report error when tacacs enabled:
Sep 1 09:25:18.189395 vlab-01 ERR tcpdump: nss_tacplus: /etc/tacplus_nss.conf fopen failed
Sep 1 09:25:18.189606 vlab-01 ERR tcpdump: nss_tacplus: bad config or server line for nss_tacplus
This is because debian add a patch create AppArmor profile for resource access control. The profile need update to allow tcpdump access /etc/tacplus_nss.conf.
Work item tracking
Microsoft ADO: 17667308
How I did it
Modify tcpdump AppArmor profile, add new line to allow tcpdump access TACACS config file:
/etc/tacplus_nss.conf r,
### Why I did it
syncd events should have tag sonic-events-syncd, not sonic-events-host. Created a new conf file which will have syncd events
##### Work item tracking
- Microsoft ADO **(number only)**:17747466
#### How I did it
Code change
#### How to verify it
Pipeline
Why I did it
ConfigDBConnector in supervisor-proc-exit-listener uses default parameter to connect CONFIG_DB (connect by 127.0.0.1:6379) which would fail at non-host network mode container, because they are not sharing the same network and socket.
How I did it
Add a new parameter use_unix_socket_path to this script to indicate whether to use socket to connect CONFIG_DB.
How to verify it
Build image and install it, kill critical processes in container and container crushed.
In #15080, there was a command added to re-add 127.0.0.1/8 to the lo
interface when the networking configuration is being brought down.
However, the trigger for that command is `down`, which, looking at
ifupdown2 configuration files, runs immediately after 127.0.0.1/16 is
removed. This means there may be a period of time where there are no
loopback addresses assigned to the lo interface, and redis commands will
fail.
Fix this by changing this to pre-down, which should run well before
127.0.0.1/16 is removed, and should always leave lo with a loopback
address.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Why I did it
PTF container needs to use new grpcio package.
Work item tracking
Microsoft ADO (number only):
How I did it
Update versions-py2
How to verify it
Check pipeline artifact
### Why I did it
Currently there is only rsyslog plugin support for /var/log/syslog, meaning we do not detect events that occur in frr logs such as BGP Hold Timer Expiry that appears in frr/bgpd.log.
##### Work item tracking
- Microsoft ADO **(number only)**: 13366345
#### How I did it
Add omprog action to frr/bgpd.log and frr/zebra.log. Add appropriate regex for both events.
#### How to verify it
sonic-mgmt test case
Why I did it
Add dhcp_server ipv4 feature to SONiC.
HLD: sonic-net/SONiC#1282
How I did it
To be clarify: This container is disabled by INCLUDE_DHCP_SERVER = n for now, which would cause container not build.
Add INCLUDE_DHCP_SERVER to indicate whether to build dhcp_server container
Add docker file for dhcp_server, build and install kea-dhcp4 inside container
Add template file for dhcp_server container services.
Add entry for dhcp_server to FEATURE table in config_db.
How to verify it
Build image with INCLUDE_DHCP_SERVER = y to verify:
Image can be install successfully without crush.
By config feature state dhcp_server enabled to enable dhcp_server.
* [swss] Chassis db clean up optimization and bug fixes
This commit includes the following changes:
- Fix for regression failure due to error in finding CHASSIS_APP_DB in
pizzabox (#PR 16451)
- After attempting to delete the system neighbor entries from
chassis db, before starting clearing the system interface entries,
wait for sometime only if some system neighbors were deleted.
If there are no system neighbors entries deleted for the asic coming up,
no need to wait.
- Similar changes for system lag delete. Before deleting the
system lag, wait for some time only if some system lag memebers were
deleted. If there are no system lag members deleted no need to wait.
- Flush the SYSTEM_NEIGH_TABLE from the local STATE_DB. While asic
is coming up, when system neigh entries are deleted from chassis ap
db (as part of chassis db clean up), there is no orchs/process running to
process the delete messages from chassis redis. Because of this, stale system
neigh are entries present in the local STATE_DB. The stale entries result in
creation of orphan (no corresponding data path/asic db entry) kernel neigh
entries during STATE_DB:SYSTEM_NEIGH_TABLE entries processing by nbrmgr (after
the swss serive came up). This is avoided by flushing the SYSTEM_NEIGH_TABLE from
the local STATE_DB when sevice comes up.
Signed-off-by: vedganes <veda.ganesan@nokia.com>
* [swss] Chassis db clean up bug fixes review comment fix - 1
Debug logs added for deletion of other tables (SYSTEM_INTERFACE and SYSTEM_LAG_TABLE)
Signed-off-by: vedganes <veda.ganesan@nokia.com>
---------
Signed-off-by: vedganes <veda.ganesan@nokia.com>
### Why I did it
Need a tool to extend disk size
##### Work item tracking
- Microsoft ADO **(number only)**: 25094467
#### How I did it
Install parted package
#### How to verify it
Use apt list parted command to check if it's installed
Why I did it
Enabling kdump by default for cisco-8000 by setting crashkernel cmdline arg in device installer.conf.
After bootup, sonic-kdump-config wipes crashkernel arg from /host/grub/grub.cfg, and resets USE_KDUMP in /etc/default/kdump-tools, so kdump will not be enabled on subsequent reboot.
How I did it
Setting kdump enable config as part of init_cfg.json for cisco-8000 platforms.
How to verify it
Install SONiC image with kdump enabled by default (device/hwsku/installer.conf), then reboot.
Kdump config should persist on subsequent reboots and kdump loaded during bootup
Signed-off-by: Aman Singhal <amans@cisco.com>
On S6100 we are seeing almost 100K interrupts per second on intels i801 SMBUS controller which affects systems performance.
We now disable the i801 driver interrupt and instead enable polling
Microsoft ADO (number only): 24910530
How I did it
Disable the interrupt by passing the interrupt disable feature argument to i2c-i801 driver
How to verify it
This fix is NOT applicable for ARM based platforms. Applicable only for intel based platforms:-
- On SN2700 its already disabled in Mellanox hw-mgmt
- Celestica DX010 and E1031
- Dell S6100 verified the interrupts are no longer incrementing.
- Arista 7260CX3
Signed-off-by: Prince George <prgeor@microsoft.com>
### Why I did it
1. Enhance the diagnosis information collecting mechanism
- If the option `-v` is fed, it will pass additional diagnosis flags to mlxfwmanager
- Collect all the output from mlxfwmanager and print them to syslog if it fails
2. Abort syncd in case waiting for device or upgrading firmware fails
Signed-off-by: Stephen Sun <stephens@nvidia.com>
### How I did it
#### How to verify it
Regression and manual test
chassis-packet: Update arp_update script for FAILED and STALE check (#16311)
1. Fixing an issue with FAILED entry resolution retry.
Neighbor entries in arp table may sometimes enter a FAILED state when the far end is down and reports the state as follows:
2603:10e2:400:3::1 dev PortChannel19 router FAILED
While the arp_update script handles the entries for FAILED in the following format, the above was not handled due to the token location (extra router keyword at index 4):
2603:10e2:400:3::1 dev PortChannel19 FAILED
The former format may appear if an arp resolution is tried on a link that is known but the far end goes down, e.g., pinging a STALE entry while the far end is down.
2. Refreshing STALE entries to make sure the far end is reachable.
STALE entries for some backend ports may appear in chassis-packet when no traffic is received for a while on the port. When the far end goes down, it is expected for BFD to stop sending packets on the session for which the far end is not reachable. But as the entry is known as stale, on the Cisco chassis, BFD keeps sending packets. Refreshing the stale entry will keep active links as reachable in the neighbor table while the entries for the far end down will enter a failed state. FAILED state entries will be retired and entered reachable when far end comes back up.
* Fix the Loopback0 IPv6 address of LC's in chassis not reachable from peer device's
* Assign the metric vaule for Ipv6 default route learnt via RA message to higher value so that BGP learnt default route is higher priority.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
* [chassis]Chassis DB cleanup when asic comes up
Cleanup the entries from the following tables in chassis app db in
redis_chassis server in the supervisor
(1) SYSTEM_NEIGH
(2) SYSTEM_INTERFACE
(3) SYSTEM_LAG_MEMBER_TABLE
(4) SYSTEM_LAG_TABLE
As part of the clean up only those entries created by the asic that
is coming up are deleted. The LAG IDs used by the asics are also
de-allocated from SYSTEM_LAG_ID_TABLE and SYSTEM_LAG_ID_SET
- Added check to run the chassis db clean up only for voq switches.
Signed-off-by: vedganes <veda.ganesan@nokia.com>
### Why I did it
Need a tool to check certificate's detail of information.
##### Work item tracking
- Microsoft ADO **(number only)**: 25020260
#### How I did it
Install pyOpenSSL package for k8s master
#### How to verify it
Pip3 list to check whether it's installed when include_kubernetes_master=y
#### Why I did it
To enable qos config for a certain backend deployment mode, for resource-type "Compute-AI".
This deployment has the following requirement:
- Config below enabled if DEVICE_TYPE as one of backend_device_types
- Config below enabled if ResourceType is 'Compute-AI'
- 2 lossless TCs' (2, 3)
- 2 lossy TCs' (0,1)
- DSCP to TC map uses 4 DSCP code points and maps to the TCs' as follows:
"DSCP_TO_TC_MAP": {
"AZURE": {
"48" : "0",
"46" : "1",
"3" : "3",
"4" : "4"
}
}
- WRED profile has green {min/max/mark%} as {2M/10M/5%}
This required template change <as in the PR> in addition to the vendor qos.json.j2 file (not included here).
### How I did it
#### How to verify it
- with the above change and the vendor config change, generated the qos.json file and verified that the objective stated in "Why I did it" was met
- verified no error
### Description for the changelog
Update qos_config.j2 for Comptue-AI deployment on one of backend device type roles
