Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
Currently we leveraged the Supervisor to monitor the running status of critical processes in each container and it is more reliable and flexible than doing the monitoring by Monit. So we removed the functionality of monitoring the critical processes by Monit.
How I did it
I removed the script process_checker and corresponding Monit configuration entries of critical processes.
How to verify it
I verified this on the device str-7260cx3-acs-1.
Why I did it
In upgrade scenarios, where config_db.json is not carry forwarded to new image, it could be left w/o TACACS credentials.
Added a service to trigger 5 minutes after boot and restore TACACS, if /etc/sonic/old_config/tacacs.json is present.
How I did it
By adding a service, that would fire 5 mins after boot.
This service apply tacacs if available.
How to verify it
Upgrade and watch status of tacacs.timer & tacacs.service
You may create /etc/sonic/old_config/tacacs.json, with updated credentials
(before 5mins after boot) and see that appears in config & persisted too.
Which release branch to backport (provide reason below if selected)
201911
202006
202012
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
This PR aims to monitor the memory usage of streaming telemetry container and restart streaming telemetry container if memory usage is larger than the pre-defined threshold.
How I did it
I borrowed the system tool Monit to run a script memory_checker which will periodically check the memory usage of streaming telemetry container. If the memory usage of telemetry container is larger than the pre-defined threshold for 10 times during 20 cycles, then an alerting message will be written into syslog and at the same time Monit will run the script restart_service to restart the streaming telemetry container.
How to verify it
I verified this implementation on device str-7260cx3-acs-1.
Why I did it
Currently, there is a bug in the ntp.conf jinja2 template where it will ignore the src_intf directive in CONFIG_DB if there are multiple IP addresses associated with an interface. This code change fixes that bug and allows the template to select the correct source interface for NTP.
How I did it
I did this by modifying the macro in ntp.conf.j2 which determines if there is an ip address associated with an interface to set a state variable when it detects a valid interface entry in CONFIG_DB instead of outputting "true" directly (which could result in multiple "trues" outputted for interfaces with multiple valid IP addresses).
How to verify it
Add two ipv4 addresses to an interface in SONiC
Add the following configuration to config_db.json
{
"NTP": {
"global": {
"src_intf": "Ethernet1"
}
}
}
Replace Ethernet1 with the interface name of the one you assigned the IP addresses to.
Run sudo config reload -y
Open /etc/ntp.conf and verify that the following line exists
...
interface listen Ethernet1
...
The interface specified should be the one set in the previous steps.
Description for the changelog
[ntp] Fix ntp.conf template to allow setting of source port in CONFIG_DB
Why I did it
This SAI change is to Enable TD2 platforms to also be able to handle VFP-based sub-interfaces.
This is the feature that is also needed for TD2 platforms.
How to verify it
Guohan and Team has validated this feature change on TD2 platforms
#### Why I did it
If a process limits using nodes by mempolicy/cpusets, and those nodes become memory exhaustion status, one process may be killed by oom-killer.
No panic occurs in this case, because other node's memory may be free.
This means system total status may be not fatal yet.
#### How I did it
Remove 'vm.panic_on_oom=1' kernel flag from 'vmcore-sysctl.conf '
Map priority 0 to TC 1 and priority 1 to TC 0
Send traffic on priority 0 and 1 and verified that it gets mapped correctly in hw
Signed-off-by: Neetha John <nejo@microsoft.com>
Why I did it
start pcie-check.service after config-setup.service since pcie_util depends on device_info which is available with config db metadata.
How I did it
Add config-setup.service as a dependency of pcie-check.service
How to verify it
Upon reboot, check if the pcie-check.sh throws the platform api error which is dependent on DEVICE_METADATA
This is to pick up BRCM SAI 4.3.3.5-2 which contains 2 main changes:
1. hsdk-6.5.21-p1.patch (to address some field problems related to SDK issue.
2. Fix for CS00012097141 (remove some unnecessary debug setting that was causing non functional impacting problem at boot time)
Preliminary tests looks fine. BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on S6100 DUT and all passed:
```
ipfwd/test_dir_bcast.py
fib/test_fib.py
vxlan/test_vxlan_decap.py
decap/test_decap.py
fdb/test_fdb.py
```
202012 branch is using reproducible build. The versions-py3 file must contains correct pip3 package version. Otherwise we will get a build error
```
Step 31/74 : RUN pip3 install scapy==2.4.4 pyroute2==0.5.14 netifaces==0.10.9
---> Running in d7a2401dd21d
Collecting scapy==2.4.4
Downloading scapy-2.4.4.tar.gz (1.0 MB)
Collecting pyroute2==0.5.14
Downloading pyroute2-0.5.14.tar.gz (873 kB)
ERROR: Cannot install netifaces==0.10.9 because these package versions have conflicting dependencies.
The conflict is caused by:
The user requested netifaces==0.10.9
The user requested (constraint) netifaces==0.10.7
To fix this you could try to:
1. loosen the range of package versions you've specified
2. remove package versions to allow pip attempt to solve the dependency conflict
ERROR: ResolutionImpossible: for help visit https://pip.pypa.io/en/latest/user_guide/#fixing-conflicting-dependencies
The command '/bin/sh -c pip3 install scapy==2.4.4 pyroute2==0.5.14 netifaces==0.10.9' returned a non-zero code: 1
[ FAIL LOG END ] [ target/docker-sonic-vs.gz ]
```
Why I did it
Finding running containers through "docker ps" breaks when kubernetes deploys container, as the names are mangled.
How I did it
The data is is available from FEATURE table, which takes care of kubernetes deployment too.
How to verify it
Deploy a feature via kubernetes and don't expect error from container_check.
- Support compile sonic arm image on arm server. If arm image compiling is executed on arm server instead of using qemu mode on x86 server, compile time can be saved significantly.
- Add kernel argument systemd.unified_cgroup_hierarchy=0 for upgrade systemd to version 247, according to #7228
- rename multiarch docker to sonic-slave-${distro}-march-${arch}
Co-authored-by: Xianghong Gu <xgu@centecnetworks.com>
Co-authored-by: Shi Lei <shil@centecnetworks.com>
Why I did it
Recent systemd upgrade from #7228 requires an extra cmdline parameter for dockerd to start properly.
Updating boot0 was missed as part of the systemd upgrade change.
How I did it
Just added the missing cmdline parameter in files/Aboot/boot0.j2
This change fixes#7372
How to verify it
Boot the image and dockerd should start normally.
Fix#7364
99-default.link - was always in SONiC, but previous systemd (<247) had an issue and it did not work due to issue systemd/systemd#3374. Now systemd 247 works.
However, such policy overrides teamd provided mac address which causes teamd netdev to use a random mac
address. Therefore, needs to be disabled.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
Why I did it
Support readonly version of the command vtysh
How I did it
Check if the command starting with "show", and verify only contains single command in script.
Encounter error during "config-setup boot" if the updategraph is enabled.
How I did it
Correct the code inside the config-setup script.
Remove the space between the assignment operator.
How to verify it
Remove the /etc/sonic/config_db.json and reboot the device.
Originally, it will return following error after boot up.
rv: command not found
After modification, it can correctly parse the status of updategraph without error.
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
Since we introduced a new value always_disabled for the state field in FEATURE table, the expected running container list
should exclude the always_diabled containers. This bug was found by nightly test and posted at here: issue. This PR fixes#7210.
How I did it
I added a logic condition to decide whether the value of state field of a container was always_disabled or not.
How to verify it
I verified this on the device str-dx010-acs-1.
Which release branch to backport (provide reason below if selected)
201811
201911
202006
[ x] 202012
Features may be enabled/disabled for the same topology based on run-time
configuration. This PR adds the ability to enable/disable feature based
on config db data.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
show ip interfaces is enhanced recently to support multi ASIC platforms in this PR- https://github.com/Azure/sonic-utilities/pull/1396 .
The ipintutil script as to run as sudo user, to get the ip interface from each namespace.
Add this script to the sudoer file so that show ip interface command is available for user with read-only permissions
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
Why I did it
We skip install of CNI plugin, as we don't need. But this leaves node in "not ready" state, upon joining master.
To fix, we copy this dummy .conf file in /etc/cni/net.d
How I did it
Keep this file in /usr/share/sonic/templates and copy to /etc/cni/net.d upon joining k8s master.
How to verify it
Upon configuring master-IP and enable join, watch node join and move to ready state.
You may verify using kubectl get nodes command
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
In the configuration of rsyslog, duplicate messages will be suppressed and reported in the format of message repeated n times.
Due to this behavior, if a critical process in a container exited unexpectedly, the alerting message will be written into syslog once
and not be written into syslog anymore until the second critical process exited. This PR aims to differentiate these alerting messages such that they will not be suppressed by rsyslogd and can appear in the syslog periodically.
How I did it
This PR adds a counter into the alerting message and shows how many minutes a critical process was not running.
How to verify it
I verified and test this implementation on a physical DUT.
- Why I did it
The pcie configuration file location is under plugin directory not under platform directory.
#6437
- How I did it
Move all pcie.yaml configuration file from plugin to platform directory.
Remove unnecessary timer to start pcie-check.service
Move pcie-check.service to sonic-host-services
- How to verify it
Verify on the device
- Why I did it
Group all SONiC services together and able to manage them together. Will be used in config reload command as much simpler and generic way to restart services.
- How I did it
Add services to sonic.target
- How to verify it
Together with Azure/sonic-utilities#1199
config reload -y
Signed-off-by: Stepan Blyshchak <stepanb@nvidia.com>
Fix marvell-armhf build break
The azure-storage package depends on the cryptography package. Newer
versions of cryptography require the rust compiler, the correct version
for which is not readily available in buster. Hence we pre-install an
older version here to satisfy the azure-storage dependency.
Note: This is not a problem for other architectures as pre-built versions
of cryptography are available for those. This sequence can be removed
after upgrading to debian bullseye.
- Add support for `DCS-7050SX3-48YC8` and `DCS-7050SX3-48C8` platform
- Add support for more variants of `DCS-7280CR3-32[PD]4`
- Add Supervisor to Linecard consutil support
- Complete Watchdog platform API support
- Fix some PSU behavior on `DCS-7050QX-32` and `DCS-7060CX-32S`
- Fix SEU management on `DCS-7060CX-32S`
- Allow kernel modules to build up to linux 5.10
- Rename led color `orange` to `amber`
- Miscellaneous fixes
[multi_asic][vs]: Add dependency in teamd service to start after topology service.
- Why I did it
In multi-asic VS, topology service is run after database service to set up the internal asic topology.
swss and syncd have a dependency to start after topology service is run so that the interfaces are moved to right namespace and created in the right namespace. In case of multi-asic vs, during the initial boot up, when there is no configuration added, teamd service starts and swss/syncd do not start as topology service does not start. Upon loading configuration using config_db or minigraph, swss and sycnd start up , but teamd is not restarted as swss is not stopped and started. This causes teamd to be in a bad state and requires a reload of config.
- How I did it
Add dependency in teamd service to start after topology service is completed.
- How to verify it
No change in single asic vs or platform.
No change in multi-asic regular image.
Change only in multi-asic VS. Bring up a multi-asic VS image without any configration, teamd service will fail to start due to dependency failure. Load minigraph, start topology service, load configuration, ensure all services come up.
Signed-off-by: SuvarnaMeenakshi <sumeenak@microsoft.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan arlakshm@microsoft.com
- Why I did it
This PR has the changes to support having different swss.rec and sairedis.rec for each asic.
The logrotate script is updated as well
- How I did it
Update the orchagent.sh script to use the logfile name options in these PRs(Azure/sonic-swss#1546 and Azure/sonic-sairedis#747)
In multi asic platforms the record files will be different for each asic, with the format swss.asic{x}.rec and sairedis.asic{x}.rec
Update the logrotate script for multiasic platform .
