Why I did it
Fix similar issue seen on #13739 but only for DCS-7050CX3-32S
How I did it
Add a kernel parameter to tell libata to disable NCQ
How to verify it
The message ata2.00: FORCE: horkage modified (noncq) should appear on the dmesg.
Test results using: fio --direct=1 --rw=randrw --bs=64k --ioengine=libaio --iodepth=64 --runtime=120 --numjobs=4
with NCQ
READ: bw=26.1MiB/s (27.4MB/s), 26.1MiB/s-26.1MiB/s (27.4MB/s-27.4MB/s), io=3136MiB (3288MB), run=120053-120053msec
WRITE: bw=26.3MiB/s (27.6MB/s), 26.3MiB/s-26.3MiB/s (27.6MB/s-27.6MB/s), io=3161MiB (3315MB), run=120053-120053msec
without NCQ
READ: bw=22.0MiB/s (23.1MB/s), 22.0MiB/s-22.0MiB/s (23.1MB/s-23.1MB/s), io=2647MiB (2775MB), run=120069-120069msec
WRITE: bw=22.2MiB/s (23.3MB/s), 22.2MiB/s-22.2MiB/s (23.3MB/s-23.3MB/s), io=2665MiB (2795MB), run=120069-120069msec
- Why I did it
FW for Spectrum-4 ASIC not yet available
- How I did it
Remove in Mellanox fw make files to Spectrum-4 ASIC firmware binaries.
Remove from firmware upgrade scripts to be able Spectrum-4 ASIC.
- How to verify it
Run regression test
- Why I did it
Need to add the possibility to choose between dropping packets (using ACL) on ingress or egress in Dual ToR scenario
- How I did it
Add new attribute "mux_tunnel_ingress_acl" to SYSTEM_DEFAULTS table
- How to verify it
check that new attribute exists in redis:
admin@sonic:~$ redis-cli -n 4
127.0.0.1:6379[4]> HGETALL SYSTEM_DEFAULTS|mux_tunnel_ingress_acl
1."state"
2."false"
Signed-off-by: Andriy Yurkiv <ayurkiv@nvidia.com>
Fixe #12047. After the c++ implementation of the sonic-db-cli, sonic-db-cli PING command tries to initialize the global database for all instances database starting. If all instance database-config.json are not ready yet. it will crash and generate core file. PR sonic-net/sonic-swss-common#701 only fix the crash and the process abortion.
Signed-off-by: mlok <marty.lok@nokia.com>
Why I did it
Some products might experience an occasional IO failure in the communication between CPU and SSD.
Based on some research it could be attributable to some device not handling ATA NCQ (Native Command Queue).
This issue currently affect 4 products:
DCS-7170-32C*
DCS-7170-64C
DCS-7060DX4-32
DCS-7260CX3-64
How I did it
This change disable NCQ on the affected drive for a small set of products.
How to verify it
When the fix is applied, these 2 patterns can be found in the dmesg.
ata1.00: FORCE: horkage modified (noncq)
NCQ (not used)
Test results using: fio --direct=1 --rw=randrw --bs=64k --ioengine=libaio --iodepth=64 --runtime=120 --numjobs=4
with NCQ (ata1.00: 61865984 sectors, multi 1: LBA48 NCQ (depth 32), AA)
READ: bw=33.9MiB/s (35.6MB/s), 33.9MiB/s-33.9MiB/s (35.6MB/s-35.6MB/s), io=4073MiB (4270MB), run=120078-120078msec
WRITE: bw=34.1MiB/s (35.8MB/s), 34.1MiB/s-34.1MiB/s (35.8MB/s-35.8MB/s), io=4100MiB (4300MB), run=120078-120078msec
without NCQ (ata1.00: 61865984 sectors, multi 1: LBA48 NCQ (not used))
READ: bw=31.7MiB/s (33.3MB/s), 31.7MiB/s-31.7MiB/s (33.3MB/s-33.3MB/s), io=3808MiB (3993MB), run=120083-120083msec
WRITE: bw=31.9MiB/s (33.4MB/s), 31.9MiB/s-31.9MiB/s (33.4MB/s-33.4MB/s), io=3830MiB (4016MB), run=120083-120083msec
Which release branch to backport (provide reason below if selected)
Go's runtime (and dockerd inherits this) uses own DNS resolver implementation by default on Linux.
It has been observed that there are some DNS resolution issues when executing ```docker pull``` after first boot.
Consider the following script:
```
admin@r-boxer-sw01:~$ while :; do date; cat /etc/resolv.conf; ping -c 1 harbor.mellanox.com; docker pull harbor.mellanox.com/sonic/cpu-report:1.0.0 ; sleep 1; done
Fri 03 Feb 2023 10:06:22 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.99 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.989/5.989/5.989/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:57245->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:23 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.56 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.561/5.561/5.561/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:53299->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:24 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.78 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.783/5.783/5.783/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:55765->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:25 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=7.17 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 7.171/7.171/7.171/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:44877->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:26 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.66 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.656/5.656/5.656/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:54604->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:27 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=8.22 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 8.223/8.223/8.223/0.000 ms
1.0.0: Pulling from sonic/cpu-report
004f1eed87df: Downloading [===================> ] 19.3MB/50.43MB
5d6f1e8117db: Download complete
48c2faf66abe: Download complete
234b70d0479d: Downloading [=========> ] 9.363MB/51.84MB
6fa07a00e2f0: Downloading [==> ] 9.51MB/192.4MB
04a31b4508b8: Waiting
e11ae5168189: Waiting
8861a99744cb: Waiting
d59580d95305: Waiting
12b1523494c1: Waiting
d1a4b09e9dbc: Waiting
99f41c3f014f: Waiting
```
While /etc/resolv.conf has the correct content and ping (and any other utility that uses libc's DNS resolution implementation) works correctly
docker is unable to resolve the hostname and falls back to default [::1]:53. This started to happen after PR https://github.com/sonic-net/sonic-buildimage/pull/13516 has been merged.
As you can see from the log, dockerd is able to pick up the correct /etc/resolv.conf only after 5 sec since first try. This seems to be somehow related to the logic in Go's DNS resolver
https://github.com/golang/go/blob/master/src/net/dnsclient_unix.go#L385.
There have been issues like that reported in docker like:
- https://github.com/docker/cli/issues/2299
- https://github.com/docker/cli/issues/2618
- https://github.com/moby/moby/issues/22398
Since this starts to happen after inclusion of resolvconf package by
above mentioned PR and the fact I can't see any problem with that (ping,
nslookup, etc. works) the choice is made to force dockerd to use cgo
(libc) resolver.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
Signed-off-by: Zhixin Zhu zhixzhu@cisco.com
Why I did it
backplane ports cable length need to be specified.
How I did it
separated handling for the specific port name.
Why I did it
To address error sometimes seen when running sonic-mgmt test_stress_routes.py::test_announce_withdraw_route on 720DT-48S
How I did it
Update boot0 logic to set platform specific varlog size for 720DT-48S
How to verify it
Verified that /var/log size increased and error is no longer observed when running test
Why I did it
Fix some unreliability seen on emmc device with some AMD CPUs
How I did it
Added a kernel parameter to add quirks to
It depends on a sonic-linux-kernel change to work properly but will be a no-op without it.
The quirk added is SDHCI_QUIRK2_BROKEN_HS200 used to downgrade the link speed for the eMMC.
- Why I did it
Support DSCP remapping in dual ToR topo on T0 switch for SKU Mellanox-SN4600c-C64, Mellanox-SN4600c-D48C40, Mellanox-SN2700, Mellanox-SN2700-D48C8.
- How I did it
Regarding buffer settings, originally, there are two lossless PGs and queues 3, 4. In dual ToR scenario, the lossless traffic from the leaf switch to the uplink of the ToR switch can be bounced back.
To avoid PFC deadlock, we need to map the bounce-back lossless traffic to different PGs and queues. Therefore, 2 additional lossless PGs and queues are allocated on uplink ports on ToR switches.
On uplink ports, map DSCP 2/6 to TC 2/6 respectively
On downlink ports, both DSCP 2/6 are still mapped to TC 1
Buffer adjusted according to the ports information:
Mellanox-SN4600c-C64:
56 downlinks 50G + 8 uplinks 100G
Mellanox-SN4600c-D48C40, Mellanox-SN2700, Mellanox-SN2700-D48C8:
24 downlinks 50G + 8 uplinks 100G
- How to verify it
Unit test.
Signed-off-by: Stephen Sun <stephens@nvidia.com>
- Why I did it
In to-sonic and multi-asic KVM-test, pretest sometimes failed. Reason is rsyslogd process can not start in teamd container. Because rsyslog.conf is empty caused by sonic-cfggen execute failed
- How I did it
If sonic-cfggen -d execute failed, execute without -d because the template file has the default value.
- How to verify it
Build image and test it over 40 times, all passed pretest.
Signed-off-by: Chun'ang Li <chunangli@microsoft.com>
- Why I did it
Added platform specific script to be invoked during SAI failure dump. Added some generic changes to mount /var/log/sai_failure_dump as read write in the syncd docker
- How I did it
Added script in docker-syncd of mellanox and copied it to /usr/bin
- How to verify it
Manual UT and new sonic-mgmt tests
* Add support for platform topology configuration service
This service invokes the platform plugin for platform specific topology
configuration.
The path for platform plugin script is:
/usr/share/sonic/device/$PLATFORM/plugins/config-topology.sh
If the platform plugin is not available, this service does nothing.
Signed-off-by: anamehra <anamehra@cisco.com>
After upgrade to brcmsai 8.1, the sdk running environment (container) recommended with mininum memory size as below
TH4/TD4(ltsw) uses 512MB
TH3 used 300MB
Helix4/TD2/TD3/TH/TH 256 MB
Base on this requirement, adjust the default syncd share memory size and set the memory size for special ACISs in platform_env.conf file for different types of Broadcom ASICs.
How I did it
Add the platform_env.conf file if none of it for broadcom platform (base on platform_asic file)
Add the 'SYNCD_SHM_SIZE' and set the value
for ltsw(TD4/TH4) devices set to 512M at least (update the platform_env.conf)
for Td2/TH2/TH devices set to 256M
for TH3 set to 300M
verify
How to verify it
verify the image with code fix
Check with UT
Check on lab devices
On a problematic device which cannot start successfully
Run with the command
$ cat /proc/linux-kernel-bde
Broadcom Device Enumerator (linux-kernel-bde)
Module parameters:
maxpayload=128
usemsi=0
dmasize=32M
himem=(null)
himemaddr=(null)
DMA Memory (kernel): 33554432 bytes, 0 used, 33554432 free, local mmap
No devices found
$ docker rm -f syncd
syncd
$ sudo /usr/bin/syncd.sh start
Cannot get Broadcom Chip Id. Skip set SYNCD_SHM_SIZE.
Creating new syncd container with HWSKU Force10-S6000
a4862129a7fea04f00ed71a88715eac65a41cdae51c3158f9cdd7de3ccc3dd31
$ docker inspect syncd | grep -i shm
"ShmSize": 67108864,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
On Normal device
$ docker inspect syncd | grep -i shm
"ShmSize": 268435456,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e"
change the config syncd_shm.ini to b85=128m
$ docker rm -f syncd
syncd
$ sudo /usr/bin/syncd.sh start
Creating new syncd container with HWSKU Force10-S6000
3209ffc1e5a7224b99640eb9a286c4c7aa66a2e6a322be32fb7fe2113bb9524c
$ docker inspect syncd | grep -i shm
"ShmSize": 134217728,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
change the config under
/usr/share/sonic/device/x86_64-dell_s6000_s1220-r0/Force10-S6000/platform_env.conf
and run command
$ cat /usr/share/sonic/device/x86_64-dell_s6000_s1220-r0/platform_env.conf
SYNCD_SHM_SIZE=300m
$ sudo /usr/bin/syncd.sh start
Creating new syncd container with HWSKU Force10-S6000
897f6fcde1f669ad2caab7da4326079abd7e811bf73f018c6dacc24cf24bfda5
$ docker inspect syncd | grep -i shm
"ShmSize": 314572800,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
- Why I did it
fixes#12907
When the management interface IP address configuration changes from dynamic to static the DNS configuration (retrieved from the DHCP server) in /etc/resolv.conf remains uncleared. This leads to a DNS configuration pointing to the wrong nameserver. To make the behavior clear DNS configuration received from DHCP should be cleared.
- How I did it
Use resolvconf package for managing DNS configuration. It is capable of tracking the source of DNS configuration and puts the configuration retrieved from the DHCP servers into a separate file. This allows the implementation of DNS configuration cleanup retrieved from DHCP during networking reconfiguration.
- How to verify it
Ensure that the management interface has no static configuration.
Check that /etc/resolv.conf has DNS configuration.
Configure a static IP address on the management interface.
Verify that /etc/resolv.conf has no DNS configuration.
Remove the static IP address from the management interface.
Verify that /etc/resolv.conf has DNS configuration retrieved form DHCP server.
Fixes#12408
Why I did it
We are running into #12408 very frequently.
This results in no syslogs from any containers as rsyslog server could not start.
some of the sonic-mgmt scripts look for log statements and error out if log is not present.
Interfaces-config service configures the loopback interface along with other interfaces. rsyslog-config reads ip address of loopback interface and generates /etc/rsyslog.conf. When this race condition happens, lo interface ip is not yet programmed and rsyslog-config ends up writing UDP server as null in /etc/rsyslog.conf.
How I did it
rsyslog-config service is started after interfaces-config service.
How to verify it
Did multiple reboots and verified that $UDPServerAddress is valid.
Adding /usr/local/bin/storyteller to READ_ONLY_CMDS. So no write access or prompt for password is needed to run storyteller.
Tested on 202205 clusters, user who didn't request write access was able to grep log using storyteller.
sign-off: Jing Zhang zhangjing@microsoft.com
Changing the default config knob value to be True for killing radv, due to the reasons below:
Killing RADV is to prevent sending the "cease to be advertising interface" protocol packet.
RFC 4861 says this ceasing packet as "should" instead of "must", considering that it's fatal to not do this.
In active-active scenario, host side might have difficulty distinguish if the "cease to be advertising interface" is for the last interface leaving.
6.2.5. Ceasing To Be an Advertising Interface
shutting down the system.
In such cases, the router SHOULD transmit one or more (but not more
than MAX_FINAL_RTR_ADVERTISEMENTS) final multicast Router
Advertisements on the interface with a Router Lifetime field of zero.
In the case of a router becoming a host, the system SHOULD also
depart from the all-routers IP multicast group on all interfaces on
which the router supports IP multicast (whether or not they had been
advertising interfaces). In addition, the host MUST ensure that
subsequent Neighbor Advertisement messages sent from the interface
have the Router flag set to zero.
sign-off: Jing Zhang zhangjing@microsoft.com
#### Why I did it
Segfault was occuring when running memory_checker
#### How I did it
Deinit publisher immediately after publishing
#### How to verify it
Manual testing
How I did it
radv sends a good-bye packet when the service is stopped, which causes a IPv6 route update on SoC side. And this update leads to an interface bouncing and causes traffic disruption even though the ToR device might already be isolated.
This PR is to mitigate the traffic disruption issue during planned maintenance, by killing radv instead of stopping. So the cease packet won't be sent.
How to verify it
Verified on dev clusters:
Traffic disruption was no longer reproducible.
radv took the killing path
if knob was off, radv would take the stopping path
sign-off: Jing Zhang zhangjing@microsoft.com
Many of these switches have had flash upgraded beyond 2G however, in
boot0 both were assigned 2GB for legacy reasons.
Remove the hardcoding of the flash size and let boot0 autodetect the available space.
Signed-off-by: Graham Hayes <gr@ham.ie>
Signed-off-by: Graham Hayes <gr@ham.ie>
The main issue is the pip/pip3 command cannot be found when the package is being installed by apt-get.
When using the dpkg install, the searching path is PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
When using the apt-get install, the searching path is PATH=/usr/sbin:/usr/bin:/sbin:/bin
But the pip/pip3 default path is at /usr/local/bin, so dpkg works, but apt-get not work.
How I did it
Export the path /usr/local/bin for pip/pip3.
Make the deb packages can be installed by apt-get.
The console of the centec-arm64 board is ttyAMA0.The current regular expression cannot be correctly parsed.
Signed-off-by: centecqianj <qianj@centec.com>
What I did:
Fix : #13117
How I did:
During build time mask only those feature/services that are disabled explicitly. Some of the features ((eg: teamd/bgp/dhcp-relay/mux/etc..)) state is determine run-time so for those feature by default service will be up and running and then later hostcfgd will mask them if needed.
So Default behavior will be
init_cfg.json.j2 during build time make state as disabled then mask the service
init_cfg.json.j2 during build time make state as another jinja2 template render string than do no mask the service
init_cfg.json.j2 during build time make state as enabled then do not mask the service
How I verify:
Manual Verification.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
Why I did it
In the voq chassis the buffer_queue configuration needs to be applied on system_port instead of the sonic port.
This PR has the change to do this.
How I did it
Modify buffer_config.j2 to generate buffer_queue configuration on system_ports if the device is Voq Chassis
How to verify it
Verify the buffer_queue configuration is generated properly using sonic-cfggen
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
- Why I did it
The followup to #12920 PR.
If the feature compilation is disabled its configuration should not be included into init_cfg.json.
- How I did it
Update init_cfg.json.j2 template to include teamd and radv features configuration only if their compilation is enabled.
- How to verify it
The default behavior is preserved. To verify the changes compile the image without overriding INCLUDE_TEAMD and INCLUDE_ROUTER_ADVERTISER options. The generated /etc/sonic/init_cfg.json should remain with no changes. Install the image and verify that both teamd and radv containers are present and running. Verify that feature state returned by show feature status command is enabled.
Change the INCLUDE_TEAMD or INCLUDE_ROUTER_ADVERTISER value to "n". Compile and install the image. Verify that feature configuration is not included in generated /etc/sonic/init_cfg.json file. Verify that show feature status output doesn't include the feature.
- Why I did it
Remove dependency on interfaces-config.service to speed up boot, because interfaces-config.service takes a lot of time on boot.
- How I did it
Changed service files for swss, syncd.
- How to verify it
Boot and check swss/syncd start time comparing to interfaces-config
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
- Why I did it
Support syslog rate limit configuration feature
- How I did it
Remove unused rsyslog.conf from containers
Modify docker startup script to generate rsyslog.conf from template files
Add metadata/init data for syslog rate limit configuration
- How to verify it
Manual test
New sonic-mgmt regression cases
Why I did it
Ubuntu 22.04 uses cgroup2 by default, but docker.sh doesn't mount it.
As a result we get an error when trying to run docker info in chroot env:
ERROR: Cannot connect to the Docker daemon at unix:///var/run/docker.sock. Is the docker daemon running?
How I did it
mount cgroup2 in chroot if all enabled kernel cgroup controllers are currently not in use by cgroup1
So we need to mount cgroup in chroot environment on /sys/fs/cgroup.
Because inside chroot we don't know which cgroup version is used by the host we have two possible solutions:
cgroup tree for chroot is mounted by the host (it was my 1st version of this fix)
cgroup tree is mounted inside chroot based on info from /proc/cgroups (it's current version of this fix)
My 2nd version based on this code from systemd: 5c6c587ce2/src/shared/cgroup-setup.c (L35-L74)
We parse info from /proc/cgroups
Skip header line started from #
Skip controller if it's disabled (4th column = 0)
Count number of controllers with non-zero of hierarchy_id (2nd column)
If this number is not zero then we assume some of controllers are used by host system and the host system uses hybrid or legacy cgroup tree. In this case we can't use unified cgroup tree inside chroot and mount old cgroup tree (v1).
If this number is zero then we assume host system uses unified cgroup tree and we need to mount cgroup2 inside chroot.
Signed-off-by: Konstantin Vasin <k.vasin@yadro.com>
- Why I did it
This optimization is needed for DPU SONiC. DPU SONiC runs a limited set of containers and teamd and radv containers are not part of them. Unlike the other containers, there was no possibility to disable teamd and radv containers compilation.
To reduce DPU SONiC compilation time and reduce the image size this commit adds the possibility to disable their compilation.
- How I did it
Two new configuration options are added to rules/config file:
INCLUDE_TEAMD
INCLUDE_ROUTER_ADVERTISER
By default to preserve the existing behavior both options are enabled. There are two ways to override them:
To change option value to "n" in rules/config file.
To override their value using SONIC_OVERRIDE_BUILD_VARS env variable:
SONIC_OVERRIDE_BUILD_VARS="SONIC_INCLUDE_TEAMD=y SONIC_INCLUDE_ROUTER_ADVERTISER=n"
- How to verify it
The default behavior is preserved. To verify it compile the image without overriding new options. Install the image and verify that both teamd and radv containers are present and running.
To verify the new options override them with "n" value. Compile and install image. Verify that no docker containers are present. Verify that SWSS can start without errors.
Debian is shipping a systemd timer unit for logrotate, but we're also
packaging in a cron job, which means both of them will run, potentially
at the same time. Remove our cron file, and add an override to the
shipped timer file to have it be run every 10 minutes.
Fixes#12392.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan arlakshm@microsoft.com
Why I did it
Fixes#12575 and #12575
How I did it
In the PR sonic-net/sonic-platform-daemons#311 chassisd updates to CHASSIS_FABRIC_ASIC_INFO with the fabric asic info.
Updating the asic_status.py to read from the correct table.
How to verify it
test on chassis
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
Why I did it
Limiting #12804 changes to PikeZ platform only (Arista-720DT-48S). Note that this is a short term workaround for this platform until SDK investigation on SDK init failure on docker syncd restart due to DMA issues is resolved.
How I did it
Retrieve platform name from /host/machine.conf and only reload SDK kmods on Arista-720DT-48S platform.
Signed-off-by: Michael Li <michael.li@broadcom.com>
- Why I did it
There's a slowdown in bootup related to the execution of a show command during startup of swss service. show is a pretty heavy command and takes long time to execute ~2 sec.
- How I did it
I replaced show with sonic-db-cli which takes a ms to run.
- How to verify it
Boot the switch and verify swss is active.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
During docker build, host files can be passed to the docker build through
docker context files. But there is no straightforward way to transfer
the files from docker build to host.
This feature provides a tricky way to pass the cache contents from docker
build to host. It tar's the cached content and encodes them as base64 format
and passes it through a log file with a special tag as 'VCSTART and VCENT'.
Slave.mk in the host, it extracts the cache contents from the log and stores them
in the cache folder. Cache contents are encoded as base64 format for
easy passing.
<!--
Please make sure you've read and understood our contributing guidelines:
https://github.com/Azure/SONiC/blob/gh-pages/CONTRIBUTING.md
** Make sure all your commits include a signature generated with `git commit -s` **
If this is a bug fix, make sure your description includes "fixes #xxxx", or
"closes #xxxx" or "resolves #xxxx"
Please provide the following information:
-->
#### Why I did it
#### How I did it
#### How to verify it
Why I did it
There is an issue on the Arista PikeZ platform (using T3.X2: BCM56274) while running SONiC. If the 'syncd' container in SONiC is restarted, the expected behaviour is that syncd will automatically restart/recover; however it does not and always fails at create_switch due to BCM SDK kmod DMA operation cancellation getting stuck.
Sep 16 22:19:44.855125 pkz208 ERR syncd#syncd: [none] SAI_API_SWITCH:platform_process_command:428 Platform command "init soc" failed, rc = -1. Sep 16 22:19:44.855206 pkz208 INFO syncd#supervisord: syncd CMIC_CMC0_PKTDMA_CH4_DESC_COUNT_REQ:0x33#015 Sep 16 22:19:44.855264 pkz208 CRIT syncd#syncd: [none] SAI_API_SWITCH:platformInit:1909 initialization command "init soc" failed, rc = -1 (Internal error). Sep 16 22:19:44.855403 pkz208 CRIT syncd#syncd: [none] SAI_API_SWITCH:sai_driver_init:642 Error initializing driver, rc = -1. ... Sep 16 22:19:44.855891 pkz208 CRIT syncd#syncd: [none] SAI_API_SWITCH:brcm_sai_create_switch:1173 initializing SDK failed with error Operation failed (0xfffffff5).
Reloading the BCM SDK kmods allows the switch init to continue properly.
How I did it
If BCM SDK kmods are loaded, unload and load them again on syncd docker start script.
How to verify it
Steps to reproduce:
In SONiC, run 'docker ps' to see current running containers; 'syncd' should be present.
Run 'docker stop syncd'
Wait ~1 minute.
Run 'docker ps' to see that syncd is missing.
Check logs to see messages similar to the above.
Signed-off-by: Michael Li <michael.li@broadcom.com>
- Why I did it
Add support for compiling Spectrum-4 ASIC firmware to the SONiC image
Add support for Spectrum-4 ASIC firmware upgrade
- How I did it
Update Mellanox fw make files to include Spectrum-4 ASIC firmware binaries.
Update firmware upgrade scripts to be able to detect Spectrum-4 ASIC.
- How to verify it
Run regression tests
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Why I did it
The PR is to apply separated DSCP_TO_TC_MAP and TC_TO_QUEUE_MAP to uplink ports on dualtor.
The traffic with DSCP 2 and DSCP 6 from T1 is treated as lossless traffic.
DSCP TC Queue
2 2 2
6 6 6
Traffic with DSCP 2 or DSCP 6 from downlink is still treated as lossy traffic as before.
How I did it
Define DSCP_TO_TC_MAP|AZURE_UPLINK and TC_TO_QUEUE_MAP|AZURE_UPLINK.
How to verify it
Verified by UT
Verified by coping the new template to a testbed, and rendering a config_db.json
Why I did it
There were some changes in apt source code in version 2.1.9.
As a result apt used in bullseye (2.2.4) is intolerant to network issues.
This was fixed in 10631550f1 Already fixed version is used in bookworm (2.5.4)
And not yet affected version is used in buster (1.8.2.3)
How I did it
Set Acquire::Retries to 3 for sonic-slave-bullseye, docker-base-bullseye and final Debian image.
Ref: https://bugs.launchpad.net/ubuntu/+source/apt/+bug/1876035
Signed-off-by: Konstantin Vasin k.vasin@yadro.com
Why I did it
The current lazy installer relies on a filename sort for both unpack and configuration steps. When systemd services are configured [started] by multiple packages the order is by filename not by the declared package dependencies. This can cause the start order of services to differ between first-boot and subsequent boots. Declared systemd service dependencies further exacerbate the issue (e.g. blocking the first-boot script).
The current installer leaves packages un-configured if the package dependency order does not match the filename order.
This also fixes a trivial bug in [Build]: Support to use symbol links for lazy installation targets to reduce the image size #10923 where externally downloaded dependencies are duplicated across lazy package device directories.
How I did it
Changed the staging and first-boot scripts to use apt-get:
dpkg -i /host/image-$SONIC_VERSION/platform/$platform/*.deb
becomes
apt-get -y install /host/image-$SONIC_VERSION/platform/$platform/*.deb
when dependencies are detected during image staging.
How to verify it
Apt-get critical rules
Add a Depends= to the control information of a package. Grep the syslog for rc.local between images and observe the configuration order of packages change.
Added Support to runtime render bgp and teamd feature `state` and lldp `has_asic_scope` flag
Needed for SONiC on chassis.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
Co-authored-by: mlok <marty.lok@nokia.com>
Fix the issue where arp_update will not ping some of the ip's even
though they are in failed state since grep of that ip on ip neigh show
command does not do exact word match and can return multiple match.
Why I did it
nameserver and domain entries from build system fsroot gets into sonic image.
How I did it
Clear /etc/resolv.conf before building image
How to verify it
Built image with it and verified with install that /etc/resolv.conf is empty
Why I did it
Unify the Debian mirror sources
Make easy to upgrade to the next Debian release, not source url code change required.
Support to customize the Debian mirror sources during the build
Relative issue: #12523
