[write_standby]: Ignore non-auto interfaces
* In the event that `write_standby.py` is used to automatically switchover interfaces when linkmgrd or bgp crashes, ignore any interfaces that are not configured to auto-switch
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
[mux] Update Service Install With SONiC Target
Recent PR grouped all SONiC service into sonic.taget. The install section
of mux.service was not update and this causes delays when using config
reload as the service failed state is not being reset.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
[mux] Start Mux on Only Dual-ToR Platform
mux docker depends on the presence of mux cable hardware and is
supposed to run only Gemini ToRs. This PR change the mux feature
config in order to enable mux docker based on device configuration.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
This PR deletes local-to-buildimage linkmgrd and creates new submodule
pointing to github repo of sonic-linkmgrd.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
During warm reboot, linkmgrd would go away and so heartbeats will
be lost. This would result in standby link son peer ToR to pull the
link active. This is undesirable since we would not create tunnel
from the ToR that is being rebooted to the peer ToR. This PR
implicitly lock the state of the mux if config is not set to auto.
Also, orchagent does not initialize MUX to it hardware state, rather
it initilizes MUX to Unknown state. linkmgrd will detect this situation
and probe MUX state to correct orchagent state.
There a fix for the case when state os switched MUX is delayed. The
PR will poll the MUX for the new state. This is required to update
the state ds and hence create/tear tunnel.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Linkmgrd monitors link status, mux status, and link state. Has
the link becomes unhealthy, linkmgrd will trigger mux switchover
on a standby ToR ensuring uninterrupted service to servers/blades.
This PR is initial implementation of linkmgrd.
Also, docker-mux container hold packages related to maintaining and managing
mux cable. It currently runs linkmgrd binary that monitor and switches
the mux if needed.
This PR also introduces mux-container and starts linkmgrd as startup when
build is configured with INCLUDE_MUX=y
Edit: linkmgrd PR will follow.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Related work items: #2315, #3146150
The dhcp6relay rules file had a line overwriting a variable for
docker-dhcp-relay. Remove that line.
This line caused a limited impact where if some (many?) of the docker
containers were already built, except for dhcp-relay, and the build
failed or was interrupted, then dhcp-relay container would fail to build
because this variable was overwritten and the python3-swsscommon
wouldn't get installed into the slave container. Most builds would be
fine, though.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
This is to address an issue where it was observed that SAI operations sometime make take a very long to time complete (over 45ms). It was determined that the ALPM distributed thread was causing this issue.
The fix is to disable this debug thread that has no functional purpose.
Preliminary tests looks fine. BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the fib test cases on 7050CX3 (TD3), TD2, TH, TH2, and TH3 based platforms and
thy all passed.
Why I did it
During swss container startup, if ndppd starts up before/with vlanmgrd, ndppd will be pinned at nearly 100% CPU usage.
How I did it
Only start ndppd after vlanmgrd is running. Also, call ndppd directly instead of through bash for improved logging and to prevent orphaned processes.
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
- Why I did it
Wrong SKU configuration will lead to longer init flow.
This will affect fast-reboot feature by increasing the traffic downtime.
Since MLNX met the required downtime period with this SKU this bug found with a delay.
- How I did it
Add the required split labels for ports.
- How to verify it
Run fast-reboot with this platform using SN3800-D112C8 SKU.
These changes are included in this PR:
07e1f79 [syncd] Add workaround for warm boot new objects (#959)
50fd353 Fix the option missing in kernel config issue (#956)
e77503c [syncd] Comparison logic workaround for empty buffer profile (#906) (#941)
This is to pick up BRCM SAI 4.3.5.1-6 fixes which contains the following fixes:
1. CS00012213351 SONIC-50679: [TH, TH2] Warm-reboot from 3.5 to 4.3 fails due to null objects discovered
2. CS00012182162: SONIC-49805 TD3 MMU config profile optimization changes
3. CS00012210826:SONIC-50205/760c60fc: Should read MMU_INTFI_MMU_PORT_TO_MMU_QUEUES_FC_BKP for TH3
Preliminary tests looks fine. BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on 7050CX3 (TD3) T0 DUT and all passed:
```
fib/test_fib.py
vxlan/test_vxlan_decap.py
fdb/test_fdb.py
decap/test_decap.py
ipfwd/test_dip_sip.py
ipfwd/test_dir_bcast.py
acl/test_acl.py
vlan/test_vlan.py
platform_tests/test_reboot.py
```
Signed-off-by: Neetha John <nejo@microsoft.com>
Why I did it
Storage T0's have all vlan members as tagged
How I did it
Since currently minigraph does not have a unique way to identify if a vlan member is tagged/untagged and to ensure other scenarios are not broken, the logic used is to just update the vlan member type as 'tagged' when we determine that it is a storage backend device. This change will apply only to storage backend T0's since storage backend T1's will not have vlan member information
How to verify it
Updated the storage backend T0 testcases to check for tagged vlan members
Added testcase to check if a T1 and backend T1 device generates an empty vlan member table
Existing vlan member testcases are good enough for checking if any regression has been caused for regular T0's
Build sonic_config_engine-1.0-py3-none-any.whl successfully
#### Why I did it
Fixed an issue that changing SDK version leads to cache framework taking cached syncd RPC image rather then rebuilding syncd RPC based on new syncd with new SDK.
Investigation showed that cache framework calculates a component hash based on direct dependencies. Syncd RPC image hash consists of two parts: one is the flags of syncd RPC (platform, ENABLE_SYNCD_RPC) and syncd RPC direct dependencies makefiles. None of the syncd RPC direct dependencies are modified when SDK version changes, so hash is unchanged.
#### How I did it
To fix this issue, include the hash of dependencies into current component hash calculation, e.g.:
In calcultation of the hash ```docker-syncd-mlnx-rpc.gz-274dfed3f52f2effa9989fc-39344350436f9b06d28b470.tgz```, the hash of syncd is included: ```docker-syncd-mlnx.gz-48ee88ac54b201e0e107b15-7bbea320025177a2121e440.tgz``` in which the hash of SDK is included.
#### How to verify it
Build with cache enabled and check that changing SDK version leads to a different hash of syncd rpc image:
SDK version 4.5.1002:
```
docker-syncd-mlnx.gz-48ee88ac54b201e0e107b15-7bbea320025177a2121e440.tgz
docker-syncd-mlnx-rpc.gz-274dfed3f52f2effa9989fc-39344350436f9b06d28b470.tgz
```
SDK version 4.5.1002-005:
```
docker-syncd-mlnx.gz-18baf952e3e0eda7cda7c3c-e5668f4784390d5dffd55af.tgz
docker-syncd-mlnx-rpc.gz-4a6e59580eda110b5709449-552f76be135deaf750aeab2.tgz
```
bf7214c (HEAD -> 202012, origin/202012) [y_cable] add support for manual/standby mode in xcvrd for muxcable; fix download firmware version retrieval logic while download firmware in progress (#220)
fc6a41e (HEAD -> 202012, origin/202012) Fix typo in the simulated y_cable driver (#226)
Signed-off-by: vaibhav-dahiya <vdahiya@microsoft.com>
* [Nokia ixs7215] Platform API fixes
This commit delivers the following fixes
- Fix bug preventing access to second PSU eeprom
- Fix bug preventing updates to front panel PSU status led
- Fix SFP reset test case failure
* Fix LGTM alert
This commit more fully declares the HW capabilities of the Nokia-7215
platform. For example, support for the threshold values associated with each
thermal sensor is described. The intent here is to inform the sonic-mgmt
platform test cases of which HW features are supported.
This commit must align with PR# 4521 within the sonic-mgmt git repo which is
currently under review. Any changes to that PR will need to be reflected in
this commit.
Fix the check used to wait for interfaces to come up. The group name in
the supervisor config files has changed from isc-dhcp-relay to
dhcp-relay.
Also, in the wait script, wait 10 additional seconds after the vlans,
port channels, and any interfaces are up. This is because dhcrelay
listens on all interfaces (in addition to port channels and vlans), and
to ensure that it stays in a clean state during runtime, wait some extra
time to make sure that those interfaces are created as well.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
