Signed-off-by: Jostar Yang jostar_yang@accton.com.tw
Why I did it
Fix led drv because CPLD SPEC is updated.
Fix i2c bus order
How I did it
Fix led drv. Set blacklist to i801 and ismt. Let accton util to modprobe i801 and ismt.
How to verify it
Test led and sensors cmd. Results are fine.
Why I did it
To fix I2C bus order to meet with HW SPEC. Let i801 use bus-0 and ismt use bus-1
How I did it
Modprobe i801 and then do ismt. So i801 will use bus-0 and ismt will use bus-1.
How to verify it
Test show cmd and sensors work well
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
AS7816 support AT or non-AT DUT. They use different pmbus i2c bus. So use "pre_pddf_init.sh" to check this case.
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
* [AS4630-54PE] Add to support PDDF
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
* Fix LGTM alerts
* Fix LGTM alerts
* Fix LGTM alerts
* Add post_device.sh to turn off stk led
* Add to support system_health
* Correct the wait and timeout mechanism for better CPU usage
* Add event.c to support port evt change
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
* [AS7726-32X] Add to support mulit PSU in PDDF
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
* Modify SN offset and include path
* Fix device_name to PSU2-EEPROM in PSU2
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Why I did it
Old fan drv will be build fail under kernel 5.10. It get below error message.
/sonic/platform/broadcom/sonic-platform-modules-accton/as7312-54xs/modules/accton_as7312_54x_fan.c:483:5: error: implicit declarat ion of function 'set_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
set_fs(KERNEL_DS);
^~~~~~
sget_fc
How I did it
These code is old design and they are not needed currently. So remove them.
Signed-off-by: Jostar Yang <jostar_yang@accton.com>
* Add intel_iommu=off to installer.conf
* This solve flooding DMAR err msg: "handling fault status reg 2"
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* remove customized at24 driver
* Use kernel 5.10.46 upstream at24 driver directly. The ADDR16 issue on
old driver has gone.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* pin I2C-0/I2C-1 bus order
* otherwise, sometimes I2C-0/I2C-1 will be assigned to the undesired one.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* fix i2c bus num for fan driver
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* backward compatible with R0A/R0B HW
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
Enable pca954x idle_disconnect to avoid possible I2C device address conflict.
How I did it
Change pca954x device_attr idle_state to -2 (MUX_IDLE_DISCONNECT).
How to verify it
Cat pca954x device_attr idle_state and confirm the value is -2.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
CPLD offset in led drv is incorrect.
#### How to verify it
echo 1 > brightness, show green on in DIAG led
echo 3 > brightness, show red on in DIAG led
echo 4 > brightness, show blue on in DIAG led
echo 5 > brightness, show green blinking in DIAG led
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
Add needed code to pddf_custom_psu.c to deal with multi PSU and get SN.
How to verify it
Plugin new PSU (3Y) and test,
```
root@sonic:/sys/bus/i2c/drivers/psu/9-0050# cat psu_serial_num
S0A000X601919000013
root@sonic:/sys/bus/i2c/drivers/psu/9-0050# cat psu_model_name
YESM1300AM
root@sonic:/home/admin# pddf_psuutil mfrinfo
PSU Status Manufacturer ID Model Serial Fan Airflow Direction
PSU1 NOT OK 3Y POWER YESM1300AM S0A000X601919000007 exhaust
PSU2 OK 3Y POWER YESM1300AM S0A000X601919000013 exhaust
```
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Add support for Accton as9726-32d platform
This pull request is based on as9716-32d, so I reference as9716-32d to create new model: as9726-32d.
This module do not need led driver to control led, FPGA can handle it.
I also implement API2.0(sonic_platform) for this model, CPLD driver, PSU driver, Fan driver to control these HW behavior.
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
bug fix: #5914
Validated for tx_disable function of SFP+ on AS7312-54X, AS5812-54X, AS5712-54x, and AS5812-54x.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
Fix 259 alerts reported by the LGTM tool:
- 245 for Unused import
- 7 for Testing equality to None
- 5 for Duplicate key in dict literal
- 1 for Module is imported more than once
- 1 for Unused local variable
Original converting from register is wrong, it makes the fan speed much higher than it is. Change the way fan speed is calculated from CPLD.
Signed-off-by: roy_lee <roy_lee@accton.com>
HW set qsfp port to reset at default. so need SW to set to normal when boot.
1. Modify cpld driver to invert reset offset value
2. Set to normal when boot.
**- Why I did it**
The tx_disable function isn't work for the accton_ax5835-54x device.
**- How I did it**
Fix the incorrect path of the sfp node path inside the util file.
**- How to verify it**
Test with
"sudo accton_as5835_54x_util.py show"
"sudo accton_as5835_54x_util.py set sfp"
There should see correct value for module_present and module_tx_disable. And should able to set it.
Signed-off-by: kuanyu_chen <kuanyu_chen@edge-core.com>
3y Power YPEB-1200am PSU doens't support read fan_dir from pmbus register
Check with vendor this PUS type only support F2B fan direction. So add to show "F2B"
when red psu_fan_dir sysfs.
1. undefine led_classdev_register as it is defined in leds.h
2. header file location change
a. linux/i2c/pmbus.h -> linux/pmbus.h
b. linux/i2c-mux-gpio.h -> linux/platform_data/i2c-mux-gpio.h
c. linux/i2c/pca954x.h -> linux/platform_data/pca954x.h
