In order to make the sai update easier, change the URL pattern to a more unified format, which can be update automated latter.
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
Why I did it
1.57.x SDK based incremental drop that addresses a few egress ACL and drop counter failures. Hostname, vtysh, and incorrect queue watermark issue are addressed too.
How I did it
Update cisco-8000 submodule to v0.2.3
How to verify it
Which release branch to backport (provide reason below if selected)
- Why I did it
ethtool is not able to read certain pages(eg. page 11h) of CMIS cables.
SDK provides a set of sysfs to expose the transceiver EEPROM, now we migrate from using ethtool to read these sysfs for transceiver EEPROM reading.
- How I did it
replace ethtool with accessing the SDK sysfs for cable EEPROM reading.
Adjust the offset according to the SDK sysfs memory map.
- How to verify it
run sonic-mgmt sfp-related regression test case.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- Why I did it
Update SDK/FW version - 4.5.3186/2010_3186 in order to have the following changes:
New functionality:
1. Added support for 6.5W (Class 8) in ports 49-50, 53-54, 57-58, and 61-62 on SN4600 system
Fix the following issues:
1. On very rare occasion (~1/100K), during I2C transaction with MMS1V50-WM and MMS1V90-WR modules on SN4700 system, the module may send unexpected stop which violate the I2C specification, possibly affecting the link up flow
2. When running 1GbE speeds on SN4600 system, the port remained active while peer side was closed
3. While toggling the cable with ‘sfputil lpmode on/off’, error msg like “ERR pmon#xcvrd: Receive PMPE error event on module 1: status {X} error type {y}” could be received
4. When toggling many ports of the Spectrum devices while raising 10GbE link up and link maintenance is enabled, the switch may get stuck and may need to be rebooted
5. When trying to reconfigure the Flex Parser header and Flex transition parameters after ISSU, the switch will returned an error even if the configuration was identical to that done before performing the ISSU
6. While moving from lossless to lossy mode while shared headroom was used, reduction of the shared headroom can only be done prior to pool type change and when shared headroom is not utilized
7. SLL configuration is missing in SDK dump
8. If TTL_CMD_COPY is used in Encap direction for a packet with no TTL, then the value passed in the ttl data structure will be used if non-zero (default 255 if zero)
9. PCI calibration changes from a static to a dynamic mechanism
10. Layer 4 port information is not initialized for BFD packet event. To address the issue, remote peer UDP port information was added in BFD packet event
11. SDK returned error when FEC mode is set on twisted pair, when FEC was set to None
- How I did it
Update pointer for the SDK/FW
- How to verify it
Run regression tests
Signed-off-by: dprital <drorp@nvidia.com>
Why I did it
Change the path of sonic submodules that point to "Azure" to point to "sonic-net"
How I did it
Replace "Azure" with "sonic-net" on all relevant paths of sonic submodules
Pick up fix for CS00012263713 (mirrored packet with extra VLAN Tag) BRCM SAI 4.3.7.1-1
Preliminary tests look fine. BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on 7050CX3 (TD3) T0 DUT and all passed:
fib/test_fib.py
acl/test_acl.py
arp/test_neighbor_mac_noptf.py
fdb/test_fdb.py
decap/test_decap.py
pc/test_lag_2.py
pc/test_po_cleanup.py
pc/test_po_update.py
everflow/test_everflow_ipv6.py
everflow/test_everflow_testbed.py
route/test_default_route.py
ipfwd/test_dip_sip.py
copp/test_copp.py
crm/test_crm.py
Update SDK/FW version - 4.5.2320/2010_2320 in order to have the following fixes:
• Spectrum-3 | PCI calibration changes from a static to a dynamic mechanism.
• [VxLAN] TTL was set to 0 for non IP traffic (such as ARP)
Pick upfollowing fixes and update BRCM SAI to 4.3.7.0:
CS00012208537: Add back previous commit 54c5bc4848eb748
CS00012253061,SONIC-63280: WB from 3.5 to 4.3, followed by WB to 4.3
CS00012207978: SDK-296517, time spent for SAI operations
CS00012245601,SONIC-62898: Egress ACL Counted ad Interface TX drops
Update pcbb with Fixes for CS00012243699
Upgrade on pcbb with Fixes for KB0025353, CS00012221689, CS00012221688, KB0025391, CS00012230519
commit of "CS00012221688:PFC frames egressing, PFC storm happens simultaneously on 2 ports" is purposely skipped to be picked up later due to SWSS dependency not ready.
Why I did it
How I did it
How to verify it
Tested build target, successful
Manually run these tests after installing sai binary within image 20201231.73 on 7050CX3 (TD3) T0 DUT, all passed.
vxlan/test_vxlan_decap.py
fdb/test_fdb.py
pfcwd/test_pfcwd_all_port_storm.py
acl/null_route/test_null_route_helper.py
acl/test_acl.py
vlan/test_vlan.py
platform_tests/test_reboot.py
Signed-off-by: zitingguo-ms <zitingguo@microsoft.com>
- Why I did it
Update SAI version - 1.22.0.0
Update SDK/FW version - 4.5.2318/2010_2318
SAI Changes:
1. Port FEC fix for multiple speeds
2. Next hop group optimized bulk API
3. Support BFD remote-disc exchange in negotiation stage
4. Reduce verbosity of shared database already exists print
SDK/FW Fixes:
1. Cr space timeout on Hold and Release GW - at warmboot
2. SPC-1 Port in stuck PHY_UP after peer side rebooted
3. memory leak in sx_api_router_ecmp_update_set
- How I did it
Update pointer for the new SAI and SDK/FW
- How to verify it
Run regression tests
- Why I did it
New changes in this new HW-MGMT package:
1. hw-mgmt: chassis events: Fix voltmon address conflict on connecting
2. hw-mgmt: topology: Add COMEX BRDWL respin support
a. Removed A2D sensor from all COMEX BRDWL boards
b. Add COMEX BRDWL boards with register defined (config3)
- How I did it
Advance the hw-mgmt repo pointer and update the hw-mgmt version number
- How to verify it
Run platform-related regression test cases on the new testbed.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- Why I did it
This is for the eventual support of multiple architectures for the mellanox platform.
- How I did it
Change the location of the binaries in Switch-SDK-drivers so that the path specifies the target architecture in addition to the target distribution that the debians are built for.
This is the most straightforward way to separate binaries built against different architectures and selectively target them for installation in the mellanox SONiC image.
- How to verify it
Build SONiC for mellanox and verify it compiles successfully.
Why I did it
- To reduce rc.local script execution time.
- Time consumption of rc.local script is around 22 seconds in S6100.
How I did it
- Moving platform-modules-s6100.service and s6100-lpc-monitor.service asynchronous to rc.local script.
How to verify it
- Load the image with the changes and the time consumption of rc.local script reduced from 22 seconds(approx.) to 14 seconds(approx.) during warm-/fast-reboot upgrades.
- sonic-mgmt test results.
This fixes the build for armhf to be able to use '/device///installer.conf' files. Specifically, armhf needs support to be able to change the size of /var/log/ directory. It is hardcoded to 512 bytes on all armhf platforms currently. This change will allow any armhf platform to be able to use an installer.conf file to customize the installed image.
Important fixes since 202012-v0.97:
V0.102:
Hwsku changes to Cisco-8102-C64
Fix for watermark clear issue
V0.101:
Fix for dhcp_relay test issue
V0.100:
Fix for container_autorestart test issue
V0.99:
Fix for everflow test issue
Fix for pfcwd test issue
Fix for copp test issue
V0.98:
Fix for qos_sai test issue
RDMA enhancements dev complete and content included in this drop (flow based VoQ, ECN, Alpha)
Signed-off-by: Kevin Wang <shengkaiwang@microsoft.com>
Support Tunnel PFC/pcbb feature on Broadcom platform.
How to verify it
Tested build target, successful
make target/docker-syncd-brcm.gz
manual run those tests after installing sai binary within image 20201231.67 on 7050CX3 (TD3) T0 DUT, all passed
fib/test_fib.py
vxlan/test_vxlan_decap.py
fdb/test_fdb.py
decap/test_decap.py
pfcwd/test_pfcwd_all_port_storm.py
acl/null_route/test_null_route_helper.py
acl/test_acl.py
vlan/test_vlan.py
platform_tests/test_reboot.py
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
Why I did it
To remove the ipmihelper.py in S5248f directory to prevent the image label being marked 'dirty', due to the file being replaced by the ipmihelper.py in common folder during build.
How I did it
Remove ipmihelper.py in S5248f directory.
How to verify it
Build a broadcom image and verify that the tracked files are not modified.
Which release branch to backport (provide reason below if selected)
201811
201911
202006
202012
202106
202111
Description for the changelog
DellEMC S5248f : Remove duplicate ipmihelper.py
Link to config_db schema for YANG module changes
A picture of a cute animal (not mandatory but encouraged)
- Why I did it
To include latest fixes:
1. Warmboot | When trying to reconfigure the Flex Parser header and Flex transition parameters after ISSU, the switch will returned an error even if the configuration was identical to that done before performing the ISSU.
2. Link Up | When toggling many ports of the Spectrum devices while raising 10GbE link up and link maintenance is enabled, the switch may get stuck and may need to be rebooted.
3. Shared buffer | While moving from lossless to lossy while shared headroom was used, reduction of the shared headroom can only be done prior to pool type change and when shared headroom is not utilized.
- How I did it
Updated SAI & SDK submodules along with the relevant Makefiles
- How to verify it
Build an image and run tests from "sonic-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
* [Mellanox] Update SDK/FW to 4.5.1500/2010.1500 and SAI version to 1.21.0.1
Signed-off-by: Sudharsan Dhamal Gopalarathnam <sudharsand@nvidia.com>
* Updating Switch-SDK-drivers submodule pointer
* Updating SAI version
Incorrect high-threshold and critical-high-threshold values are displayed for
some of the temperature sensors. This commit fixes that.
Co-authored-by: Qi Luo <qiluo-msft@users.noreply.github.com>
Co-authored-by: Jing Kan <jika@microsoft.com>
Why I did it
Kernel hang in during early boot is caused due overwriting of device tree with uncompressing kernel. Added the fdt_high which gives a safe offset from kernel location.
How I did it
Setting uboot environment variable fdt_high.
How to verify it
Successful boot of bullseye kernel on Marvell Armada 380/385.
Change-Id: I3e2521780f5ecdb3bdf6cbb6542250814ca11959
Signed-off-by: Pavan Naregundi <pnaregundi@marvell.com>
