Multi-asic Docker instances are created behind Docker's default bridge
which doesn't allow talking to other Docker instances that are in the
host network (like database-chassis).
On linecards, we configure midplane interfaces to let per-asic docker
containers talk to CHASSIS_DB on the supervisor through internal chassis
network.
On the supervisor we don't need to use chassis internal network, but we
still need a similar setup in order to allow fabric containers to talk
to database-chassis
With this PR in, you flap BGP and use events_tool to see the published events.
With telemetry PR #111 in and corresponding submodule update done in buildimage, one could run gnmi_cli to capture BGP flap events.
*Preventing ebtables rules to be applied on KVM image. The ebtables rules in SONiC are added to prevent ARP as well as L2 forwarding to be blocked in linux kernel since the hardware will take care of the actual L2 forward. However this is not the case with KVM where linux needs to forward even L2 packets
What/Why I did:
Issue1: By setting up of ipvlan interface in interface-config.sh we are not tolerant to failures. Reason being interface-config.service is one-shot and do not have restart capability.
Scenario: For example if let's say database service goes in fail state then interface-services also gets failed because of dependency check but later database service gets restart but interface service will remain in stuck state and the ipvlan interface nevers get created.
Solution: Moved all the logic in database service from interface-config service which looks more align logically also since the namespace is created here and all the network setting (sysctl) are happening here.With this if database starts we recreate the interface.
Issue 2: Use of IPVLAN vs MACVLAN
Currently we are using ipvlan mode. However above failure scenario is not handle correctly by ipvlan mode. Once the ipvlan interface is created and ip address assign to it and if we restart interface-config or database (new PR) service Linux Kernel gives error "Error: Address already assigned to an ipvlan device." based on this:https://github.com/torvalds/linux/blob/master/drivers/net/ipvlan/ipvlan_main.c#L978Reason being if we do not do cleanup of ip address assignment (need to be unique for IPVLAN) it remains in Kernel Database and never goes to free pool even though namespace is deleted.
Solution: Considering this hard dependency of unique ip macvlan mode is better for us and since everything is managed by Linux Kernel and no dependency for on user configured IP address.
Issue3: Namespace database Service do not check reachability to Supervisor Redis Chassis Server.
Currently there is no explicit check as we never do Redis PING from namespace to Supervisor Redis Chassis Server. With this check it's possible we will start database and all other docker even though there is no connectivity and will hit the error/failure late in cycle
Solution: Added explicit PING from namespace that will check this reachability.
Issue 4:flushdb give exception when trying to accces Chassis Server DB over Unix Sokcet.
Solution: Handle gracefully via try..except and log the message.
Why I did it
To support address sanitizer for Mellanox syncd
How I did it
/var/log/asan is mapped for syncd container (the same as for swss)
container stop() has a timeout (60s) for syncd (the same as for swss)
This is so libasan has enough time to generate a report.
added ASAN's log path to Mellanox syncd supervisord.conf
added "asan: yes" to sonic_version.yml
How to verify it
Added artificial memory leaks
Compiled with ENABLE_ASAN=y
Installed the image on DUT
Rebooted the DUT
Verified that /var/log/asan/syncd-asan.log contains the leaks
Signed-off-by: Yakiv Huryk <yhuryk@nvidia.com>
Why I did it
In the bringup of tomahawk4/trident4, we realized that such chips need a larger size of /dev/shm in syncd container, so we added the option --shm-size to the docker create for syncd. The default value for shm-size is 64m; after this change, people can add SYNCD_SHM_SIZE=128m to platform_env.conf to change it to 128m.
How to verify it
We verified that after this change, 1) on existing platforms without platform_env.conf, the size of /dev/shm in syncd container (df -h | grep shm) is still the default 64M; 2) after we add SYNCD_SHM_SIZE=128m to platform_env.conf, /dev/shm in syncd becomes 128M.
Implement infrastructure that allows enabling address sanitizer
for docker containers. Enable address sanitizer for SWSS container.
- Why I did it
To add a possibility to compile SONiC applications with address sanitizer (ASAN).
ASAN is a memory error detector for C/C++. It finds:
1. Use after free (dangling pointer dereference)
2. Heap buffer overflow
3. Stack buffer overflow
4. Global buffer overflow
5. Use after return
6. Use after the scope
7. Initialization order bugs
8. Memory leaks
- How I did it
By adding new ENABLE_ASAN configuration option.
- How to verify it
By default ASAN is disabled and the SONiC image is not affected.
When ASAN is enabled it inspects all allocation, deallocation, and memory usage that the application does in run time. To verify whether the application has memory errors tests that trigger memory usage of the application should be run. Ideally, the whole regression tests should be run. Memory leaks reports will be placed in /var/log/asan/ directory of SONiC host OS.
Signed-off-by: Oleksandr Ivantsiv <oivantsiv@nvidia.com>
Why I did it
database.sh failed to create the database for namespace in multiasic platform.
The latest code Docker version 20.10.x, command "docker create" no longer takes optional "NET=" with empty value. Syntax error show with current docker create command in database.sh. Issue #9503
How I did it
Modify the docker_image_ctl.j2 to set default network setting NET="bridge" instead of empty for namespace database.
Why I did it
Fix for issue #8389
How I did it
The /etc/rsyslog.conf is empty file which cause the FATAL of the process rsyslogd in the global instance database container. The function updateSyslogConf() should only generate the rsyslog.conf for containers in the namespace. it should not do it for the containers in the global instance. Instead, default rsyslog.conf should be used. Especially for database container, updateSyslogConf() is called before the database container is created. The result cause the sonic-cfggen failed to generate the rsyslog.conf.Why I did it
Fix for issue #8389
How I did it
The /etc/rsyslog.conf is empty file which cause the FATAL of the process rsyslogd in the global instance database container. The function updateSyslogConf() should only generate the rsyslog.conf for containers in the namespace. it should not do it for the containers in the global instance. Instead, default rsyslog.conf should be used. Especially for database container, updateSyslogConf() is called before the database container is created. The result cause the sonic-cfggen failed to generate the rsyslog.conf.
Signed-off-by: mlok <marty.lok@nokia.com>
- Why I did it
This is to update the common sonic-buildimage infra for reclaiming buffer.
- How I did it
Render zero_profiles.j2 to zero_profiles.json for vendors that support reclaiming buffer
The zero profiles will be referenced in PR [Reclaim buffer] Reclaim unused buffers by applying zero buffer profiles #8768 on Mellanox platforms and there will be test cases to verify the behavior there.
Rendering is done here for passing azure pipeline.
Load zero_profiles.json when the dynamic buffer manager starts
Generate inactive port list to reclaim buffer
Signed-off-by: Stephen Sun <stephens@nvidia.com>
The common startup script used for SONiC containers is calling an inline
python command that uses Python 2 syntax, and thus errors out when run
with Python 3. Make this work with Python 3.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
As a part of warmboot, redis database is dumped:
c97fe546e5/scripts/fast-reboot (L269)
However, this dump file is deleted, after it is loaded back into db post reboot.
The DB dump can be useful for debugging purpose, hence taking a backup of it can be useful.
Instead of deleting the dump, rename and keep the dump.
#### Why I did it
Use a predefined variable to get vendor information when the swss docker container is created
#### How I did it
Use `{{ sonic_asic_platform }}` instead of `$SONIC_CFGGEN -y /etc/sonic/sonic_version.yml -v asic_type`
#### How to verify it
Manually test.
This PR creates a directory firmware on the HOST with the path /usr/share/sonic/firmware, as well as this is
mounted on PMON container with the same path /usr/share/sonic/firmware. This is required for firmware
upgrade support for muxcable as currently by design all Y-Cable API's are called by xcvrd. As such if CLI has
to transfer a file to PMON we need to mount a directory from host to PMON just for getting the firmware files.
Hence we require this change.
Signed-off-by: vaibhav-dahiya <vdahiya@microsoft.com>
The voq system lag id boundary is set in redis-chassis. Changes include
setting this from database-chassis container. This fixes a timing issue
in finding datbase_config.json file from redis directory which is
created from database container. Since database container usually
starts after database-chassis container the existence of this file is
unreliable while running the command. Running the command under
database-chassis container makes sure that the database_config.json form
redis-chassis directory is guaranteed to be available and hence fixes the
timing issue.
Signed-off-by: vedganes <vedavinayagam.ganesan@nokia.com>
#### Why I did it
Following the discussion in another PR https://github.com/Azure/sonic-buildimage/pull/7708#discussion_r642933510 , since there will be multi subfolders under **/var/log/mellanox**, so we agreed to only mount this folder and the subfolders will be created afterward on demand.
#### How I did it
during the syncd docker creation, only mount folder **/var/log/mellanox**
#### How to verify it
build an Mellanox image and verify the related folder on the host and docker side.
Signed-off-by: vedganes <vedavinayagam.ganesan@nokia.com>
Changes for setting platfrom specific lag id boundary id in the chassis
app db. The platfrom specific lag id boundaries are supplied via
chassisdb.conf. The lag_id_start and lag_id_end boundary values sourced
from this file are set in chassis app db which will be used by lag id
allocator to allocate unique lag id in atomic fashion
- Why I did it
I made the docker_img_ctl.j2 applicable for more dockers (including application extensions dockers) by adding an option not to mount tmpfs on /tmp/ and /var/tmp/. In some applications /tmp/ is a different docker volume which can't be tmpfs.
Also, I added and ability to pass REPO[:TAG]|[@digest]/IMAGE_ID instead of just REPO name.
- How I did it
Modified docker_img_ctl.j2 and docker makefiles.
- How to verify it
Run it on the switch.
Following changes were done for ebtables:
- Support for Multi-asic platforms. Ebtable filters are installed in namespace for multi-asic and not host. On Single asic installed on host.
- For Multi-asic platforms we don't want to install on host otherwise Namespace-to-Namespace communication does not happens since ARP Request are not forwarded.
- Updated to use text file to restore ebtables rules then the binary format. Rules are restore as part of Database docker init instead of rc.local
- Removed the ebtable service files for buster as not needed as filters are restored/installed as part of database docker init.
All the binaries are pre-installed with ebtables* binary are same as ebatbles-legacy-*
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
The Portchannels were not getting cleaned up as the cleanup activity was taking more than 10 secs which is default docker timeout after which a SIGKILL will be send.
Fixes#6199
To check if it works out for this issue in 201911 ? #6503
This issue is significantly seen in master branch compared to 201911 because the Portchannel cleanup takes more time in master. Test on a DUT with 8 Port Channels.
master
admin@str-s6000-acs-8:~$ time sudo systemctl stop teamd
real 0m15.599s
user 0m0.061s
sys 0m0.038s
Sonic 201911.v58
admin@str-s6000-acs-8:~$ time sudo systemctl stop teamd
real 0m5.541s
user 0m0.020s
sys 0m0.028s
* First cut image update for kubernetes support.
With this,
1) dockers dhcp_relay, lldp, pmon, radv, snmp, telemetry are enabled
for kube management
init_cfg.json configure set_owner as kube for these
2) Each docker's start.sh updated to call container_startup.py to register going up
As part of this call, it registers the current owner as local/kube and its version
The images are built with its version ingrained into image during build
3) Update all docker's bash script to call 'container start/stop/wait' instead of 'docker start/stop/wait'.
For all locally managed containers, it calls docker commands, hence no change for locally managed.
4) Introduced a new ctrmgrd service, that helps with transition between owners as kube & local and carry over any labels update from STATE-DB to API server
5) hostcfgd updated to handle owner change
6) Reboot scripts are updatd to tag kube running images as local, so upon reboot they run the same image.
7) Added kube_commands.py to handle all updates with Kubernetes API serrver -- dedicated for k8s interaction only.
**- Why I did it**
To support dynamic buffer calculation.
This PR also depends on the following PRs for sub modules
- [sonic-swss: [buffermgr/bufferorch] Support dynamic buffer calculation #1338](https://github.com/Azure/sonic-swss/pull/1338)
- [sonic-swss-common: Dynamic buffer calculation #361](https://github.com/Azure/sonic-swss-common/pull/361)
- [sonic-utilities: Support dynamic buffer calculation #973](https://github.com/Azure/sonic-utilities/pull/973)
**- How I did it**
1. Introduce field `buffer_model` in `DEVICE_METADATA|localhost` to represent which buffer model is running in the system currently:
- `dynamic` for the dynamic buffer calculation model
- `traditional` for the traditional model in which the `pg_profile_lookup.ini` is used
2. Add the tables required for the feature:
- ASIC_TABLE in platform/\<vendor\>/asic_table.j2
- PERIPHERAL_TABLE in platform/\<vendor\>/peripheral_table.j2
- PORT_PERIPHERAL_TABLE on a per-platform basis in device/\<vendor\>/\<platform\>/port_peripheral_config.j2 for each platform with gearbox installed.
- DEFAULT_LOSSLESS_BUFFER_PARAMETER and LOSSLESS_TRAFFIC_PATTERN in files/build_templates/buffers_config.j2
- Add lossless PGs (3-4) for each port in files/build_templates/buffers_config.j2
3. Copy the newly introduced j2 files into the image and rendering them when the system starts
4. Update the CLI options for buffermgrd so that it can start with dynamic mode
5. Fetches the ASIC vendor name in orchagent:
- fetch the vendor name when creates the docker and pass it as a docker environment variable
- `buffermgrd` can use this passed-in variable
6. Clear buffer related tables from STATE_DB when swss docker starts
7. Update the src/sonic-config-engine/tests/sample_output/buffers-dell6100.json according to the buffer_config.j2
8. Remove buffer pool sizes for ingress pools and egress_lossy_pool
Update the buffer settings for dynamic buffer calculation
The service crash when the platform boots due to missing waits.
/usr/bin/database.sh tries to operate on a missing socket and fails.
We now wait for the chassis database to be ready the same way we do database.
API getMount() API was not updated to handle multi-asic platforms
Updated API getMount() to return abspath() for Docker Mount Point
and use that one for mount point comparison
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
use correct chassisdb.conf path while bringing up chassis_db service on VoQ modular switch.chassis_db service on VoQ modular switch.
resolves#5631
Signed-off-by: Honggang Xu <hxu@arista.com>
bring up chassisdb service on sonic switch according to the design in
Distributed Forwarding in VoQ Arch HLD
Signed-off-by: Honggang Xu <hxu@arista.com>
**- Why I did it**
To bring up new ChassisDB service in sonic as designed in ['Distributed forwarding in a VOQ architecture HLD' ](90c1289eaf/doc/chassis/architecture.md).
**- How I did it**
Implement the section 2.3.1 Global DB Organization of the VOQ architecture HLD.
**- How to verify it**
ChassisDB service won't start without chassisdb.conf file on the existing platforms.
ChassisDB service is accessible with global.conf file in the distributed arichitecture.
Signed-off-by: Honggang Xu <hxu@arista.com>
* [Multi-Asic] Forward SNMP requests destined to loopback IP, and coming in through the front panel interface
present in the network namespace, to SNMP agent running in the linux host.
* Updates based on comments
* Further updates in docker_image_ctl.j2 and caclmgrd
* Change the variable for net config file.
* Updated the comments in the code.
* No need to clean up the exising NAT rules if present, which could be created by some other process.
* Delete our rule first and add it back, to take care of caclmgrd restart.
Another benefit is that we delete only our rules, rather than earlier approach of "iptables -F" which cleans up all rules.
* Keeping the original logic to clean the NAT entries, to revist when NAT feature added in namespace.
* Missing updates to log_info call.
We are moving toward building all Python packages for SONiC as wheel packages rather than Debian packages. This will also allow us to more easily transition to Python 3.
Python files are now packaged in "sonic-utilities" Pyhton wheel. Data files are now packaged in "sonic-utilities-data" Debian package.
**- How I did it**
- Build and install sonic-utilities as a Python package
- Remove explicit installation of wheel dependencies, as these will now get installed implicitly by pip when installing sonic-utilities as a wheel
- Build and install new sonic-utilities-data package to install data files required by sonic-utilities applications
- Update all references to sonic-utilities scripts/entrypoints to either reference the new /usr/local/bin/ location or remove absolute path entirely where applicable
Submodule updates:
* src/sonic-utilities aa27dd9...2244d7b (5):
> Support building sonic-utilities as a Python wheel package instead of a Debian package (#1122)
> [consutil] Display remote device name in show command (#1120)
> [vrf] fix check state_db error when vrf moving (#1119)
> [consutil] Fix issue where the ConfigDBConnector's reference is missing (#1117)
> Update to make config load/reload backward compatible. (#1115)
* src/sonic-ztp dd025bc...911d622 (1):
> Update paths to reflect new sonic-utilities install location, /usr/local/bin/ (#19)
sonic-cfggen is now using Unix Domain Socket for Redis DB. The socket
is created using root account. Subsequently, services that are started
as admin fails to start. This PR creates redis group and add admin
user to redis group. It also grants read/write access on redis.sock
for redis group members.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
startup when doing redis PING since database_config.json getting
generated from jinja2 template is still not ready.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
* [platform] Add Support For Environment Variable
This PR adds the ability to read environment file from /etc/sonic.
the file contains immutable SONiC config attributes such as platform,
hwsku, version, device_type. The aim is to minimize calls being made
into sonic-cfggen during boot time.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
This PR has changes to support accessing the bcmsh and bcmcmd utilities on multi ASIC devices
Changes done
- move the link of /var/run/sswsyncd from docker-syncd-brcm.mk to docker_image_ctl.j2
- update the bcmsh and bcmcmd scripts to take -n [ASIC_ID] as an argument on multi ASIC platforms
* [sonic-buildimage] Changes to make network specific sysctl
common for both host and docker namespace (in multi-npu).
This change is triggered with issue found in multi-npu platforms
where in docker namespace
net.ipv6.conf.all.forwarding was 0 (should be 1) because of
which RS/RA message were triggered and link-local router were learnt.
Beside this there were some other sysctl.net.ipv6* params whose value
in docker namespace is not same as host namespace.
So to make we are always in sync in host and docker namespace
created common file that list all sysctl.net.* params and used
both by host and docker namespace. Any change will get applied
to both namespace.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
* Address Review Comments and made sure to invoke augtool
only one and do string concatenation of all set commands
* Address Review Comments.
Add changes for syslog support for containers running in namespaces on multi ASIC platforms.
On Multi ASIC platforms
Rsyslog service is only running on the host. There is no rsyslog service running in each namespace.
On multi ASIC platforms the rsyslog service on the host will be listening on the docker0 ip address instead of loopback address.
The rsyslog.conf on the containers is modified to have omfwd target ip to be docker0 ipaddress instead of loopback ip
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
* Changes to make default route programming
correct in multi-asic platform where frr is not running
in host namespace. Change is to set correct administrative distance.
Also make NAMESPACE* enviroment variable available for all dockers
so that it can be used when needed.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
* Fix review comments
* Review comment to check to add default route
only if default route exist and delete is successful.
* Multi DB with namespace support, Introducing the database_global.json file
for supporting accessing DB's in other namespaces for service running in
linux host
* Updates based on comments
* Adding the j2 templates for database_config and database_global files.
* Updating to retrieve the redis DIR's to be mounted from database_global.json file.
* Additional check to see if asic.conf file exists before sourcing it.
* Updates based on PR comments discussion.
* Review comments update
* Updates to the argument "-n" for namespace used in both context of parsing minigraph and multi DB access.
* Update with the attribute "persistence_for_warm_boot" that was added to database_config.json file earlier.
* Removing the database_config.json file to avioid confusion in future.
We use the database_config.json.j2 file to generate database_config.json files dynamically.
* Update the comments for sudo usage in docker_image_ctrl.j2
* Update with the new logic in PING PONG tests using sonic-db-cli. With this we wait till the
PONG response is received when redis server is up.
* Similar changes in swss and syncd scripts for the PING tests with sonic-db-cli
* Updated with a missing , in the database_config.json.j2 file, Do pip install of j2cli in docker-base-buster.
