adding noTLS mode for debugging purpose
Removing config-set for port 8080. It fails to start telemetry if docker restarts in case on noTLS mode because it expects log_level config to be present as well.
- Why I did it
Initially, we used Monit to monitor critical processes in each container. If one of critical processes was not running
or crashed due to some reasons, then Monit will write an alerting message into syslog periodically. If we add a new process
in a container, the corresponding Monti configuration file will also need to update. It is a little hard for maintenance.
Currently we employed event listener of Supervisod to do this monitoring. Since processes in each container are managed by
Supervisord, we can only focus on the logic of monitoring.
- How I did it
We borrowed the event listener of Supervisord to monitor critical processes in containers. The event listener will take
following steps if it was notified one of critical processes exited unexpectedly:
The event listener will first check whether the auto-restart mechanism was enabled for this container or not. If auto-restart mechanism was enabled, event listener will kill the Supervisord process, which should cause the container to exit and subsequently get restarted.
If auto-restart mechanism was not enabled for this contianer, the event listener will enter a loop which will first sleep 1 minute and then check whether the process is running. If yes, the event listener exits. If no, an alerting message will be written into syslog.
- How to verify it
First, we need checked whether the auto-restart mechanism of a container was enabled or not by running the command show feature status. If enabled, one critical process should be selected and killed manually, then we need check whether the container will be restarted or not.
Second, we can disable the auto-restart mechanism if it was enabled at step 1 by running the commnad sudo config feature autorestart <container_name> disabled. Then one critical process should be selected and killed. After that, we will see the alerting message which will appear in the syslog every 1 minute.
- Which release branch to backport (provide reason below if selected)
201811
201911
[x ] 202006
* First cut image update for kubernetes support.
With this,
1) dockers dhcp_relay, lldp, pmon, radv, snmp, telemetry are enabled
for kube management
init_cfg.json configure set_owner as kube for these
2) Each docker's start.sh updated to call container_startup.py to register going up
As part of this call, it registers the current owner as local/kube and its version
The images are built with its version ingrained into image during build
3) Update all docker's bash script to call 'container start/stop/wait' instead of 'docker start/stop/wait'.
For all locally managed containers, it calls docker commands, hence no change for locally managed.
4) Introduced a new ctrmgrd service, that helps with transition between owners as kube & local and carry over any labels update from STATE-DB to API server
5) hostcfgd updated to handle owner change
6) Reboot scripts are updatd to tag kube running images as local, so upon reboot they run the same image.
7) Added kube_commands.py to handle all updates with Kubernetes API serrver -- dedicated for k8s interaction only.
**- Why I did it**
We were building a custom version of Supervisor because I had added patches to prevent hangs and crashes if the system clock ever rolled backward. Those changes were merged into the upstream Supervisor repo as of version 3.4.0 (http://supervisord.org/changes.html#id9), therefore, we should be able to simply install the vanilla package via pip. This will also allow us to easily move to Python 3, as Python 3 support was added in version 4.0.0.
**- How I did it**
- Remove Makefiles and patches for building supervisor package from source
- Install Python 3 supervisor package version 4.2.1 in Buster base container
- Also install Python 3 version of supervisord-dependent-startup in Buster base container
- Debian package installed binary in `/usr/bin/`, but pip package installs in `/usr/local/bin/`, so rather than update all absolute paths, I changed all references to simply call `supervisord` and let the system PATH find the executable to prevent future need for changes just in case we ever need to switch back to build a Debian package, then we won't need to modify these again.
- Install Python 2 supervisor package >= 3.4.0 in Stretch and Jessie base containers
Why/How I did:
Make sure first error syslog is triggered based on FAULT TOLERANCE condition.
Added support of repeat clause with alert action. This is used as trigger
for generation of periodic syslog error messages if error is persistent
Updated the monit conf files with repeat every x cycles for the alert action
We want to let Monit to unmonitor the processes in containers which are disabled in `FEATURE` table such that
Monit will not generate false alerting messages into the syslog.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
When stopping the swss, pmon or bgp containers, log messages like the following can be seen:
```
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,061 ERRO pool dependent-startup event buffer overflowed, discarding event 34
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,063 ERRO pool dependent-startup event buffer overflowed, discarding event 35
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,064 ERRO pool dependent-startup event buffer overflowed, discarding event 36
Aug 23 22:50:43.789760 sonic-dut INFO swss#supervisord 2020-08-23 22:50:10,066 ERRO pool dependent-startup event buffer overflowed, discarding event 37
```
This is due to the number of programs in the container managed by supervisor, all generating events at the same time. The default event queue buffer size in supervisor is 10. This patch increases that value in all containers in order to eliminate these errors. As more programs are added to the containers, we may need to further adjust these values. I increased all buffer sizes to 25 except for containers with more programs or templated supervisor.conf files which allow for a variable number of programs. In these cases I increased the buffer size to 50. One final exception is the swss container, where the buffer fills up to ~50, so I increased this buffer to 100.
Resolves https://github.com/Azure/sonic-buildimage/issues/5241
The template is referenced relative to the script path and this could
results in errors in case script is run from root. Add explicit
path to the template file name.
Also, moving telemetry_var template to template dir.
And remove double quotes from around json dict.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
sonic-cfggen call is slow and this is taking place in the SONiC
boot up process. The change uses templates to assemble all required
vars into single template file. With this change, telemetry now calls
once into sonic-cfggen.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
**- Why I did it**
Initially, the critical_processes file contains either the name of critical process or the name of group.
For example, the critical_processes file in the dhcp_relay container contains a single group name
`isc-dhcp-relay`. When testing the autorestart feature of each container, we need get all the critical
processes and test whether a container can be restarted correctly if one of its critical processes is
killed. However, it will be difficult to differentiate whether the names in the critical_processes file are
the critical processes or group names. At the same time, changing the syntax in this file will separate the individual process from the groups and also makes it clear to the user.
Right now the critical_processes file contains two different kind of entries. One is "program:xxx" which indicates a critical process. Another is "group:xxx" which indicates a group of critical processes
managed by supervisord using the name "xxx". At the same time, I also updated the logic to
parse the file critical_processes in supervisor-proc-event-listener script.
**- How to verify it**
We can first enable the autorestart feature of a specified container for example `dhcp_relay` by running the comman `sudo config container feature autorestart dhcp_relay enabled` on DUT. Then we can select a critical process from the command `docker top dhcp_relay` and use the command `sudo kill -SIGKILL <pid>` to kill that critical process. Final step is to check whether the container is restarted correctly or not.
libpython2.7, libdaemon0, libdbus-1-3, libjansson4 are common
across different containers. move them into docker-base-stretch
Signed-off-by: Guohan Lu <lguohan@gmail.com>
maintains backward compatibility to search original x509 location
when telemetry table does not have certs
Signed-off-by: Guohan Lu <lguohan@gmail.com>
When telemetry is in secure mode ,the monitor will have error log of the match string "--insecure". So I modify to be compatiable with insecure mode and secure mode.
Co-authored-by: Ubuntu <ubuntu@ip-10-5-1-21.ap-south-1.compute.internal>
* Add a monit config file for teamd container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file in teamd container
into base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for snmp container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of snmp container into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for dhcp_relay container in the dir
base_image_files.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of dhcp_relay
container into base image under /etc/monit/conf.d.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for router advertiser container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of router advertiser
contianer into base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Pmon] Add a monit config file for pmon container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Pmon] Add a copy mechanism to put the monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Add a monit config file for lldp container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Add a copy mechanism to put the monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Add a monit config file for BGP container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Add a copy mechanism to put monit config file into the base
image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Add a monit config file for the swss container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Add a copy mechanism to put monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on barefoot
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-centec] Add a monit config file for syncd container on centen
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on centen
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit conifg file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on
marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on
marvell-armhf.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on nephos.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Add a monit config file for sflow container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Add a copy mechanism to put the monit conifg file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Add a monit config file for telemetry container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Add a copy mechanism to put the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Add a monit config file for database container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Dhcprelay] Change a typo.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Dhcprelay] Change the process name in monit config file to
dhcrelay.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no desserve process in syncd container on
barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process desserve in syncd container on
cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process named desserve in syncd on centec.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process named desserve in syncd on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Should not delete the process desserve in syncd container
on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
marvell-armhf.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Radv] Change the process name to radvd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Correct a typo in monit_telemetry.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-teamd] Delete the monit config file for teamd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-teamd] Delete the mechanism to copy the monit config file into
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-dhcprelay] Delete the monit config file for dhcp_relay
container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-dhcprelay] Delete the mechanism to copy the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-radv] Delete the monit config file foe radv container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-radv] Delete the mechanism to copy the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] change the monit config file for BGP container such that
monit only generates alert if the process is not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-snmp] Change the monit config file for snmp container such that
monit only generates alret if the process is not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Change the monit config file for pmon container such that
monit only generates alert if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Change the monit config file for lldp container such that
monit only generates alerts if some processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Delete the monit config file for pmon container since some
of processes are not running depended on the type of box.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Delete the copy mechanism to copy the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Change the matching name for the process lldpd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Change the monit config file for swss container such that
monit only generates alerts if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
barefoot such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Correct a typo in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
broadcom such that monit only generates alerts if the processes are not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
cavium such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container such
that monit only generates alerts if the process is not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell-arm64 such that monit only generates alerts if the process is
not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell-armhf such that monit will generate alert if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
mellanox such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sycnd] Change the monit config file for syncd container such
that monit only generates alerts if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Change the monit config file for sflow container such
that monit only generates alerts if the process is not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Change the monit config file for telemetry container
such that monit only generates alerts if the processes are not running
for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Change the monit config file for database container
such that monit only generates alerts if the process is not running for
5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Use 4 spcess to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Use 4 spaces to replace 2 space in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-snmp] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Use 4 spaces to replace 2 spaces in monit config
file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on centec.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to repalce 2 spaces in the monit config file
on nephos.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Remove the trailing extra spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Added sonic-mgmt-framework as submodule / docker
* fix build issues
* update sonic-mgmt-framework submodule branch to master
* Merged changes 70007e6d2ba3a4c0b371cd693ccc63e0a8906e77..00d4fcfed6a759e40d7b92120ea0ee1f08300fc6
00d4fcfed6a759e40d7b92120ea0ee1f08300fc6 Modified environemnt variables
* Changes to build sonic-mgmt-framework docker
* bumped up sonic-mgmt-framework commit-id
* version bump for sonic-mgmt-framework commit-it
* bumped up sonic-mgmt-framework commit-id
* Add python packages to docker
* Build fix for docker with python packages
* added libyang as dependent package
* Allow building images on NFS-mounted clones
Prior to this change, `build_debian.sh` would generate a Debian
filesystem in `./fsroot`. This needs root permissions, and one of the
tests that is performed is whether the user can create a character
special file in the filesystem (using mknod).
On most NFS deployments, `root` is the least privileged user, and cannot
run mknod. Also, attempting to run commands like rm or mv as root would
fail due to permission errors, since the root user gets mapped to an
unprivileged user like `nobody`.
This commit changes the location of the Debian filesystem to `/fsroot`,
which is a tmpfs mount within the slave Docker. The default squashfs,
docker tarball and zip files are also created within /tmp, before being
copied back to /sonic as the regular user.
The side effect of this change is that the contents of `/fsroot` are no
longer available once the slave container exits, however they are
available within the squashfs image.
Signed-off-by: Nirenjan Krishnan <Nirenjan.Krishnan@dell.com>
* bumped up sonc-mgmt-framework commit to include PR #18
* REST Server startup script is enahnced to read the settings from
ConfigDB. Below table provides mapping of db field to command line
argument name.
============================================================
ConfigDB entry key Field name REST Server argument
============================================================
REST_SERVER|default port -port
REST_SERVER|default client_auth -client_auth
REST_SERVER|default log_level -v
DEVICE_METADATA|x509 server_crt -cert
DEVICE_METADATA|x509 server_key -key
DEVICE_METADATA|x509 ca_crt -cacert
============================================================
* Replace src/telemetry as submodule to sonic-telemetry
* Update telemetry commit HEAD
* Update sonic-telemetry commit HEAD
* libyang env path update
* Add libyang dependency to telemetry
* Add scripts to create JSON files for CLI backend
Scripts to create /var/platform/syseeprom and /var/platform/system, which are back-end
files for CLI, for system EEPROM and system information.
Signed-off-by: Howard Persh <Howard_Persh@dell.com>
* In startup script, create directory where CLI back-end files live
Signed-off-by: Howard Persh <Howard_Persh@dell.com>
* build dependency pkgs added to docker for build failure fix
* Changes to fix build issue for mgmt framework
* Fix exec path issue with telemetry
* s5232[device] PSU detecttion and default led state support
* Processing of first boot in rc.local should not have premature exit
Signed-off-by: Howard Persh <Howard_Persh@dell.com>
* docker mount options added for platform, system features
* bumped up sonic-mgmt-framework commit id to pick 23rd July 2019 changes
* Added mount options for telemetry docker to get access for system and platform info.
* Update commit for sonic-utilities
* [dell]: Corrected dport map and renamed config files for S5232F
* Fix telemetry submodule commit
* added support for sonic-cli console
* [Dell S5232F, Z9264F] Harden FPGA driver kernel module
For Dell S5232F and Z9264F platforms, be more strict when checking state
in ISR of FPGA driver, to harden against spurious interrupts.
Signed-off-by: Howard Persh <Howard_Persh@dell.com>
* update mgmt-framework submodule to 27th Aug commit.
* remove changes not related to mgmt-framework and sonic-telemetry
* Revert "Replace src/telemetry as submodule to sonic-telemetry"
This reverts commit 11c3192975.
* Revert "Replace src/telemetry as submodule to sonic-telemetry"
This reverts commit 11c3192975.
* make submodule changes and remove a change not related to PR
* more changes
* Update .gitmodules
* Update Dockerfile.j2
* Update .gitmodules
* Update .gitmodules
* Update .gitmodules
reverting experimental change
* Removed syspoll for release_1.0
Signed-off-by: Jeff Yin <29264773+jeff-yin@users.noreply.github.com>
* Update docker-sonic-mgmt-framework.mk
* Update sonic-mgmt-framework.mk
* Update sonic-mgmt-framework.mk
* Update docker-sonic-mgmt-framework.mk
* Update docker-sonic-mgmt-framework.mk
* Revert "Processing of first boot in rc.local should not have premature exit"
This reverts commit e99a91ffc2.
* Remove old telemetry directory
* Update docker-sonic-mgmt-framework.mk
* Resolving merge conflict with Azure
* Reverting the wrong merge
* Use CVL_SCHEMA_PATH instead of changing directory for telemetry startup
* Add missing export
* Add python mmh3 to slave dockerfile
* Remove sonic-mgmt-framework build dep for telemetry, fix dialout startup issues
* Provided flag to disable compiling mgmt-framework
* Update sonic-utilites point latest commit id
* Point sonic-utilities to Azure accepted SHA
* Updating mgmt framework to right sha
* Add sonic-telemetry submodule
* Update the mgmt-framework commit id
Co-authored-by: jghalam <joe.ghalam@gmail.com>
Co-authored-by: Partha Dutta <51353699+dutta-partha@users.noreply.github.com>
Co-authored-by: srideepDell <srideep_devireddy@dell.com>
Co-authored-by: nirenjan <nirenjan@users.noreply.github.com>
Co-authored-by: Sachin Holla <51310506+sachinholla@users.noreply.github.com>
Co-authored-by: Eric Seifert <seiferteric@gmail.com>
Co-authored-by: Howard Persh <hpersh@yahoo.com>
Co-authored-by: Jeff Yin <29264773+jeff-yin@users.noreply.github.com>
Co-authored-by: Arunsundar Kannan <31632515+arunsundark@users.noreply.github.com>
Co-authored-by: rvasanthm <51932293+rvasanthm@users.noreply.github.com>
Co-authored-by: Ashok Daparthi-Dell <Ashok_Daparthi@Dell.com>
Co-authored-by: anand-kumar-subramanian <51383315+anand-kumar-subramanian@users.noreply.github.com>
Put a flag for fast-reboot to the db using EXPIRE feature. Using this flag in other part of SONiC to start in Fast-reboot mode. If we reload a config, the state in the db will be removed.
* adding quotes for string comparison with special characters
* Update dockers/docker-sonic-telemetry/telemetry.sh
Co-Authored-By: Joe LeVeque <jleveque@users.noreply.github.com>
* Update dockers/docker-sonic-telemetry/telemetry.sh
Co-Authored-By: Joe LeVeque <jleveque@users.noreply.github.com>
- create a dockerfile-marcros.j2 file with all common operations
written as j2 macro
- use single dockerfile instruction for COPY and RUN commands
when possible to improve build time
- reorganize dockerfile instructions to make more cache friendly
(in case someday we will remove --no-cache to build docker images)
Signed-off-by: Stepan Blyschak <stepanb@mellanox.com>
* Upgrade database and telemetry docker to stretch build
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Remove SONIC_STRETCH_DEBS list add for redis and telemetry
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
Previously use / to separate container name and program name.
However, in rsyslogd:
Precisely, the programname is terminated by either (whichever occurs first):
end of tag
nonprintable character
‘:’
‘[‘
‘/’
The above definition has been taken from the FreeBSD syslogd sources.
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* SONiC system telemetry Support
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Update package name from telemetry to sonic-telemetry
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
