init_interfaces meant to be sonic init interfaces configuration file.
However, it needs to be copied to the right file name to take effect.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
There was a fix to speed up initialization when networking used init.d
but it did not carry over to systemd networking.service. This fix will
apply the same change on the systemd service.
The result is much less time spent being blocked in networking.service.
* [warmboot] Load database from `redis-cli save`
Signed-off-by: Qi Luo <qiluo-msft@users.noreply.github.com>
* Add trivial statement to make bash function valid
Signed-off-by: Qi Luo <qiluo-msft@users.noreply.github.com>
* Update submodule sonic-utilities: Use 'redis-cli save' to dump database to file
Signed-off-by: Qi Luo <qiluo-msft@users.noreply.github.com>
* Move configdb-load.sh outside docker, and only run in cold
Signed-off-by: Qi Luo <qiluo-msft@users.noreply.github.com>
* Fix for more strict warm check
Signed-off-by: Qi Luo <qiluo-msft@users.noreply.github.com>
This driver should be loaded by sonic service. If kernel tries to load
it, the driver would be loaded with default parameters, which is not
right for sonic.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* Fix redis-py version
Signed-off-by: Qi Luo <qiluo-msft@users.noreply.github.com>
* Update submodule sonic-py-swsssdk: Fix redis-py version to 2.10.6
Signed-off-by: Qi Luo <qiluo-msft@users.noreply.github.com>
Clear WARM_RESTART table could cause component level warm restart to
fail due to missing WARM_RESTART state.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
- cold shutdown is used by regular service stop and/or fast reboot
- warm shutdown is used by warm restart and/or warm reboot
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
This script shall not flush all the entries in the state database
when it starts up, since there are entries maintained and written
by other processes outside this docker.
The issue we noticed was that the portchannel states are cleaned
up after teamsyncd writes the entries into the database, which
causes the IPs failed to be configured because intfmgrd considers
the portchannels are not ready yet.
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
Auto negotiating console speed could cause sonic to lock on a wrong
speed under rare conditions. The only way to come out of the wrong
speed is to issue line break or restart console service with forced
speed, or reboot sonic.
Lock down the console speed to avoid these situations.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
Remove the teamd.j2 templates used for starting the teamd. Add
teammgrd instead to manage all port channel related configuration
changes. Remove front panel port related configurations in
interfaces.j2 templates as well.
Remove teamd.sh script and use teammgrd to start all the teamd
processes. Remove all the logics in the start.sh script as well.
Update the sonic-swss submodule.
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
* Unify qos config with qos_config.j2 template
Signed-off-by: Wenda <wenni@microsoft.com>
* Change 7050 to use qos config template
Signed-off-by: Wenda <wenni@microsoft.com>
modified: device/arista/x86_64-arista_7050_qx32/Arista-7050-QX32/qos.json.j2
modified: device/arista/x86_64-arista_7050_qx32s/Arista-7050-QX-32S/qos.json.j2
* Change a7060, a7260, s6000, s6100, z9100 to use qos config template
Signed-off-by: Wenda <wenni@microsoft.com>
* Change mlnx devices to use qos config template
Signed-off-by: Wenda <wenni@microsoft.com>
modified: ../../../mellanox/x86_64-mlnx_msn2100-r0/ACS-MSN2100/qos.json.j2
modified: ../../../mellanox/x86_64-mlnx_msn2410-r0/ACS-MSN2410/qos.json.j2
modified: ../../../mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/qos.json.j2
modified: ../../../mellanox/x86_64-mlnx_msn2700-r0/Mellanox-SN2700-D48C8/qos.json.j2
* Change barefoot devices to use qos config template
Signed-off-by: Wenda <wenni@microsoft.com>
modified: barefoot/x86_64-accton_wedge100bf_32x-r0/montara/qos.json.j2
modified: barefoot/x86_64-accton_wedge100bf_65x-r0/mavericks/qos.json.j2
* Change accton as7212 to use qos config template
Signed-off-by: Wenda <wenni@microsoft.com>
modified: accton/x86_64-accton_as7212_54x-r0/AS7212-54x/qos.json.j2
* Apply PORT_QOS_MAP to active ports only
Signed-off-by: Wenda <wenni@microsoft.com>
* Update qos config test with qos_config.j2 template
Signed-off-by: Wenda <wenni@microsoft.com>
* Update sample output of qos-dell6100.json
Signed-off-by: Wenda <wenni@microsoft.com>
* Remove generating the default port name and index list, i.e., remove the generate_port_lists macro, because PORT is always defined
Signed-off-by: Wenda <wenni@microsoft.com>
* Include pfc_to_pg_map according to platform asic type obtained from
/etc/sonic/sonic_version.yml rather than specifying per hwsku
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Customize TC_TO_PRIORITY_GROUP_MAP and
PFC_PRIORITY_TO_PRIORITY_GROUP_MAP for barefoot
Signed-off-by: Wenda <wenni@microsoft.com>
* Unify PFC_PRIORITY_TO_PRIORITY_GROUP_MAP: remove "0":"0", "1":"1" as
these two pgs do not generate PFC frames.
Signed-off-by: Wenda <wenni@microsoft.com>
Update the hw-mgmt to latest release V.2.0.0060.
Update the related files according to the latest hw-mgmt.
Signed-off-by: Kevin Wang <kevinw@mellanox.com>
Flashes used for the 7050QX-32 and 7050QX-32S have a fw issue.
The best option to solve the problem is to upgrade to a newer firmware.
However this can only be done while in memory and take 10 seconds.
Adding an upgrade mechanism is possible but would need more
consideration as flashing the firmware and reformating the flash will
exceed the fast-reboot requirements.
A quick mitigation is to align the ext4 partition that we create on
these vfat based system on a 4k boundary.
Here we chose 1M instead but it's the same.
Newer version of sfdisk do this automatically but the one in SONiC
today doesn't have this behavior.
This workaround will only reduce the pace of the flash health
degradation. The only long term fix is to flash the firmware.
* Adapt to the new WARM_RESTART_TABLE table schema: change from restart_count to restore_count
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Update variable and function name to match restore_count name change
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Update swss submodule for warm restart schema change
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* [syncd] warn shutdown syncd process when warm boot is enabled
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* [warmboot] mount folder to hold warmboot temporary files
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* Fix a typo
* [swss.sh] refactor ssh service script code
- Move checks and waits to helper functions.
- Remove early returns from code stream
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* [swss.sh] Add debug log for service state changes
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* [syncd] Separate out syncd service from swss service
Still make them start/stop/restart synchronously so existing scripts
continue working.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* Remove extra 'After' in swss service and remove syncd docker warm boot code
Syncd warm boot needs more thinking, we can put it back once the work
flow has been defined and ready for coding/testing.
* [syncd] syncd start/stop/restart shouldn't affect swss state
Semi-detach syncd service state change from swss:
- swss state change still chase syncd service to follow except warm boot
- syncd state change will only affect itself.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* add missing '{'
* [updategraph] add support to use preset config instead of default minigraph
* Fix variable case
* Remove default minigraph case
* Remove default minigraphs and add default_sku files
Currently setting the next boot image is the same as setting a default
image.
With this change SWI_DEFAULT= will be considered the default image and
SWI= the next image.
When executing the boot0 SWI= will be overriden by SWI_DEFAULT= if it
exists and create in with the value of SWI= otherwise.
On overlay filesystem the name of the mountpoint will also match in the
mount command for overlayfs as upperdir=
To prevent detecting the wrong partition we now look for space before.
This ensure that we match mountpoint and not devices in df and mount
outputs.
- Move front panel ports and port channels MTU and IP configurations out of
the current /etc/network/interfaces file and store them in the configuration
database.
- The default MTU value for both front panel ports and the port channels is
9100. They are set via the minigraph or 9100 by default.
- Introduce portmgrd which will pick up the MTU configurations from the
configuration database.
- The updated intfmgrd will pick up IP address changes from the configuration
database.
- Update sonic-swss submodule
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
Previously use / to separate container name and program name.
However, in rsyslogd:
Precisely, the programname is terminated by either (whichever occurs first):
end of tag
nonprintable character
‘:’
‘[‘
‘/’
The above definition has been taken from the FreeBSD syslogd sources.
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* Fix potential blackholing/looping traffic and refresh ipv6 neighbor to avoid CPU hit
In case ipv6 global addresses were configured on L3 interfaces and used for peering,
and routing protocol was using link-local addresses on the same interfaces as prefered nexthops,
the link-local addresses could be aged out after a while due to no activities towards the link-local
addresses themselves. And when we receive new routes with the link-local nexthops, SONiC won't insert
them to the HW, and thus cause looping or blackholing traffic.
Global ipv6 addresses on L3 interfaces between switches are refreshed by BGP keeplive and other messages.
On server facing side, traffic may hit fowarding plane only, and no refresh for the ipv6 neighbor entries regularly.
This could age-out the linux kernel ipv6 neighbor entries, and HW neighbor table entries could be removed,
and thus traffic going to those neighbors would hit CPU, and cause traffic drop and temperary CPU high load.
Also, if link-local addresses were not learned, we may not get them at all later.
It is intended to fix all above issues.
Changes:
Add ndisc6 package in swss docker and use it for ipv6 ndp ping to update the neighbors' state on Vlan interfaces
Change the default ipv6 neighbor reachable timer to 30mins
Add periodical ipv6 multicast ping to ff02::11 to get/refresh link-local neighbor info.
* Fix review comments:
Add PORTCHANNEL_INTERFACE interface for ipv6 multicast ping
format issue
* Combine regular L3 interface and portchannel interface for looping
* Add ndisc6 package to vs docker
* Added new platform support DellEMC - Z92264f - 64x100
* Includes changes with Makefiles, sfputil, eeprom and default minigraph
* Led support for Z9264f platform
* Includes changes on default minigraph
* ipmitool implementation in pmon docker. platform_sensors script is inclued in pmon startup
* Fix for bash's memory-leak
Memory leak is observed during the execution of scripts that make use of bash-arrays. In scenarios where the offending script is executed on a regular basis (e.g. fancontrol), the leaking process may end up consuming most of the system resources.
In this PR i'm replacing bash in all the contexts where it executes (both host and dockers). The official patch for this issue is here: https://ftp.gnu.org/gnu/bash/bash-4.3-patches/bash43-040
* Fixing minor issue during code-merge
Signed-off-by: Rodny Molina <rmolina@linkedin.com>
* Initial commit
* Add Ingrasys S9180-32X platform dirver.
Signed-off-by: Wade He <chihen.he@gmail.com>
* Add bfn.service for init barefoot.
Signed-off-by: Wade He <chihen.he@gmail.com>
* [Barefoot Beta] Add some functions and fixed some bugs.
1. Update sensors.conf.
2. Fixed IO expander init.
3. Fixed PSU EEPROM.
4. Fixed MB EEPROM.
5. Add fancontrol and fan init.
6. Add SYS LED control (sys, fan, fan tray).
7. 2.5V compute and setup max and min.
8. Fixed typo MB eeprom delete address.
9. Remove coretemp to BMC.
10. Add active CPLD.
11. Modify SFP+ GPIO slave address.
12. Modify tmp75 Near Port 32 slave address.
Signed-off-by: Wade He <chihen.he@gmail.com>
* Add bfn script in /etc/init.d/
Signed-off-by: Wade He <chihen.he@gmail.com>
* Add bfn service in debian
Signed-off-by: Wade He <chihen.he@gmail.com>
* Fixed CPLD switch LED behavior.
Signed-off-by: Wade He <chihen.he@gmail.com>
* [Barefoot Beta] Fixed sensors and hwmon order.
1. Fixed ignore sensors Vbat.
2. Reorg hwmon order.
Signed-off-by: Wade He <chihen.he@gmail.com>
* Fixed PSU1 and PSU2 EEPROM order.
Signed-off-by: Wade He <chihen.he@gmail.com>
* initial barefoot checkin october 2017
* update refpoint
* update refpoints
* update refpoints to bf-master
* update refpoint
* update refpoint to tested version
* change to platform from asic
* update refpoint for swss
* revert core creation setting
* update refpoints
* add telnet for debug shell
* update refpoints 11/17/17
* missed change in file on previous merge
* [CPLD] Fixed blink LED issue.
* Fixed blink LED mask set error.
Signed-off-by: Wade He <chihen.he@gmail.com>
* Update bf_kdrv.c for 6.0.2.39
* Update bf kernel driver
* Add bf_fun kernel module.
* Update bf_tun for fixed build error
* merge with Azure master (12/12/17)
* update swss refpoint
* update refpoint of swss
* library dependency for stack unroll
* update refpoint to bf-master
* [DHCP relay]: Fix circuit ID and remote ID bugs (#1248)
* [DHCP relay]: Fix circuit ID and remote ID bugs
* Set circuit_id_len after setting circuit_id_len to ip->name
* [Platform] Add Psuutil and update sensors.conf for S9100-32X, S8810-32Q and S9200-64X (#1272)
* Add I2C CPLD kernel module for psuutil.
* Support psuutil script.
* Add voltage min and max threshold.
* Update sensors.conf for tmp75.
Signed-off-by: Wade He <chihen.he@gmail.com>
* Allow multi platform support - infra (more changes to follow)
* update relative path to include platform for clarity
* [Platform] Add Ingrasys S9130-32X and S9230-64X with Nephos Switch ASIC for "branch 201712" (#1274)
- What I did
Add switch ASIC vendor: Nephos
Add Nephos platforms: Ingrasys S9130-32X, Ingrasys S9230-64X
- How I did it
Add platform/nephos files
Add platform/nephos/sonic-platform-modules-ingrasys submodule
Add device/ingrasys/x86_64-ingrasys_s9130_32x-r0 files
Add device/ingrasys/x86_64-ingrasys_s9230_64x-r0 files
Add SONiC to support Nephos platform
Update Head of submodule src/sonic-sairedis to "3b817bb"
- How to verify it
To build SONiC installer image and docker images, run the following commands:
make configure PLATFORM=nephos
make target/sonic-nephos.bin
Check system and network feature is worked as well
- Description for the changelog
Add switch ASIC vendor and platforms for Nephos
- A picture of a cute animal (not mandatory but encouraged)
Signed-off-by: Sam Yang <yang.kaiyu@gmail.com>
* change source of files to github (from dropbox), update sairedis refpoint
* update refpoint of sairedis
* [centec] support CENTEC SAI 1.0 on 201712 branch and update e582-48x6q board (#1269)
* [marvel]: Marvell's updates for SONiC.201712 & SAI v1.0 (#1287)
* update sairedis (fast-boot refpoint)
* fix syncd rpc make files
* update refpoint to handle Makefile change (no functional change)
* [Marvell]: Add support for SLM5401-54x device (#1307)
* Marvell's updates for SONiC.201712 & SAI v1.0
* [Platform] Add Marvell's SLM5401-54x for branch 201712
* [Broadcom]: Update Boradcom SAI package to 3.0.3.3-3 (#1312) (#1321)
- update Arista 7050-QX32S config.bcm file
- update Accton th-as771*-32x100G.config.bcm files
* update refpoint for Makefile chnage in sairedis
* update refpoint - sairedis
* update sairedis to older refpoint till we debug clean build
* export asic platform for build
* update refpoint for makefiles
* [PLATFORM] Centec update E582 driver fan/epprom/sensor (#1332)
* Upload wnc-osw1800
* Modify for Barefoot suggest
* Revert bfn-platform.mk
* Update bfn-platform-wnc.mk
Update parameter name
* Update parameter name
* initial support for WNC platform
* change switch name to "switch"
* Delete bf modules for rel_7_0
* Add Ingrasys S9180 platform
Signed-off-by: Wade He <chihen.he@gmail.com>
* Modify bfnsdk for Ingrasys S9180 platform
Signed-off-by: Wade He <chihen.he@gmail.com>
* Resolved the conflict.
* Resolved the conflict.
* Update submodule path and url.
* Delete unused file.
* Update PSU GPIO and EEPROM for psuutil.
* Add psuutil in S9180-32X
Signed-off-by: Wade He <chihen.he@gmail.com>
* update refpoint
* update refpoint
* change contact email, update refpoint
* cleanup and update kernel modules
* updates based on review
* update refpoint
* update refpoint
* fix typo in config script to check for platforms
* remove stale file
* resolve conflicts
* cleanup diffs with Azure repo and update SDK debs
* update refpoints to Azure
* address review comments
* revert refpoint of swss-common
* porting the build fix from master
* porting build fix from master
* Minor Fix
* Minor fix
* Temp to sde deb packages url
* Update sonic - sairedis,swss & swss-common refpoints
* Update git modules url path to bfn repo
* updated paths for swss, swss-common & sairedis
* Update refpoint for sonic-swss to local bfn repo
* Update URL for downloading sde debian packages
* porting fix links of debian git server from master
* porting fix links of debian git server from master
* [Ingrasys] Add platform support for S9280-64X with Barefoot ASIC
* Update ref points for swss, swss-common and sairedis repos
* Add sonic platform scripts for bfn montara/maverick
* Call sh scripts instead of calling py scripts
* Address upstream PR Comments (#10)
* Update bf-master with azure/master
* Undo changes to some files
* Revert "Address upstream PR Comments (#10)"
This reverts commit a7fddb83ca.
* Address upstream comments (#11)
* Remove all non bfn specific changes from upstream PR
* Revert "Address upstream comments (#11)"
This reverts commit 559132103e.
* Undo non bfn changes
* Little more cleanup
* Add back code removed in merge
* export CONFIGURED_PLATFORM
* Update sairedis and swss refpoints
* Address Upstream PR comment
* change deb pkg dependency from 3.16.0-4-amd64 to 3.16.0-5-amd64
* Set default tx queue len for usb0 interface to 64
* Update sairedis refpoint
* Update swss ref point
* Add bfn buffer cfg files for montara/maverick as per new design
* Update buffer cfg templates for bfn montara
* add non zero size to buffer profile
* add macro to generate port lists
* Update buffer cfg templates for bfn mavericks
* add non zero size for buffer profiles
* add port generation macro
* Add missing psmisc package
* BGP docker seems to be missing killall utility being used by fast-reboot script. This is causing non graceful termination of BGP sessions.
Adding psmisc to resolve this issue.
* Update swss ref point
* Update swss ref point
* Update sairedis refpoint
* Update sairedis refpoint
* Update sairedis refpoint
* Update sairedis refpoint
* Update refpoint for sairedis and swss
* sairedis to azure master
* swss to latest bfn bf-master
* Update gitmodules
Update url for sairedis to azure master
* Correct typo in bfn platform script
* Update swss and sairedis ref points
* Update swss ref point
* Address Review comments
* Update swws path in gitmodules to azure master
* update swss refpoint
* update base docker j2 file -remove psmisc package (could be a concern, would cause fast reboot to not work correctly will fix in another PR)
* Fix sairedis refpoint broken in by previous merge
* Remove psmisc from docker base image
* This will break fast reboot as killall is required for killing bgp process and initiating graceful termination of BGP session.
Will fix this in a seperate PR. Need this for SONIC upstreaming
* Address upstream comments
* Remove bmc interface from interface jinja template and sample output interfaces file
* Add bmc interface at boot time to network interfaces for bfn bmc based platforms
* Remove autogen ingrasys debian files
* Revert "Remove autogen ingrasys debian files"
* Buffer and qos config template fix for bfn platforms (#21)
SWI-1509 Buffer and qos config template fix for bfn platforms
* Fix qos config files for montara & mavericks (#22)
* Reference only ppg 3,4 in qos files as no profiles are attached to 0,1 in buffer configs
* Fix vs test (#23)
* Use MAC from EEPROM for PortChannels
Signed-off-by: Andriy Moroz <c_andriym@mellanox.com>
* Use MAC from EEPROM in DEVICE_METADATA
Will affect MAC for VLAN interfaces
Signed-off-by: Andriy Moroz <c_andriym@mellanox.com>
* Get MAC via decode-syseeprom
Signed-off-by: Andriy Moroz <c_andriym@mellanox.com>
* hw-management is now a service
Signed-off-by: Andriy Moroz <c_andriym@mellanox.com>
* Add error handling for MAC fetch process
Signed-off-by: Andriy Moroz <c_andriym@mellanox.com>
* Update sensors.conf for 7050QX-32 and 7050QX-32S
These two platforms were using a previous version of a kernel driver.
The new one names the i2c buses differently.
We therefore need to rename them here.
* Fix the default minigraph for the 7050QX-32S
The interface offset is invalid which makes sonic-cfggen generate an
invalid config_db.jon in rc.local.
This config then silently makes orchagent/syncd fail.
* Use the partition on which sonic-aboot.swi is
Instead of always assuming /mnt/flash, use the partition where the image
to be installed lies.
This allow for the image to be on any partition.
* [rc.local] Move all constants and functions to top of file; Unify style; Reword messages
* Add function to process reboot cause upon boot
* Simplify retrieval of SONIC_VERSION per comments
* Change wording
* First part of skipping not used port for qos configuration
* Use active ports only to set QoS parameters for 6100
* Add a test for qos.json.j2
* Add a test for Dell S6100 buffers.json template
* Update submodulre
* [caclmgrd] Heuristically determine whether ACL is IPv4 or IPv6, use iptables/ip6tables accordingly
* Check all rules in table until we find one with a SRC_IP
* Revert "[serial watchdog] remove serial watchdog service dependency to rc.local (#1752)"
* Revert "[service] introducing serial port watchdog service (#1743)"
* [serial watchdog] remove serial watchdog service dependency to rc.local
When restarting this service in rc.local, the dependency causes an error
in syslog. Removing the dependency to mute the error log entry.
* remove lines with empty inputs
* [rc.local] refactor platform identification code to separate function
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* [rc.local] infrastructure to take action according to installer.conf
* [serial port watchdog] add service to watch serial port processes
Monitor serial port processes. Kill ones stuck for too long.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* [rc.local] start watchdog on serial port specified by installer.conf
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* [fast-reboot]: support encoded & gzipped minigraph in fast reboot
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* add acl.json and snmp.yml into fast-reboot
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* Fix tcpdmatch dependency
Issue: sonic_debian_extension.j2 uses tcpdmatch from src folder
which is result of libwrap build
Fix: added tcpd.deb to build results and extract required files
from build results
* Install libwrap0 and tcpd deb packages
cfggen generates new eth0 configuration. Need to first
clean existing configuration on eth0 before bring up
new configuration on eth0. Thus, we need to first bring
down eth0 before putting new configuration into /etc/network/
interfaces
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* SONiC system telemetry Support
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Update package name from telemetry to sonic-telemetry
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
commit 0965b33 added quote to build_version in /etc/sonic/sonic_version.yml,
e.g., sonic_version : '20170104.10'. scripts to use the $sonic_version need
to remove the quote.
Signed-off-by: Guohan Lu <gulv@microsoft.com>
- Service unit file not getting generated because I changed the docker
container name from 'router_advertiser' to 'radv', however I didn't
rename the service unit file template name to match. However,
slave.mk generates a service file for every docker based on its
container name, and since there was no matching 'radv.service.j2'
template file, this file stopped getting generated and therefore
the docker container was never getting started.
- Also add swss.service to 'Requires'
- Move all minigraph-related action from rc.local to updategraph
- updategraph service is now after database. All feature services are now after and depending on updategraph
* Support OS9 -> SONiC fast-reboot migration
* Address review comments. Update NOS mac in EEPROM and net.rules for eth0
* Address review comments. Update sonic-platform-modules-dell to fac81d...
* Fix script for POSIX compliance
Now properly differenciate the image installation and the kexec
operations. This is useful for fast-reboot operations.
Minor updates include
- better command line management
- using partition UUID in the command line
* [sonic build] Define folder macro for target folder /usr/sonic/share/templates
* [sonic-cfggen] allow templates to include from common folders
- Allow templates to include files under /usr/share/sonic/templates
- Allow templates to include files in the same folder as the root template
* [Buffer config] install the buffer configuration template
* [Arista7260cx3] Add buffer configuration for Arista7260CX3 T0 topology
- pg profile look up table is incomplete. Currently contains T0 default
values.
* [Arista7260cx3] Adding QoS configuration
* Address review comments
1. Stop generating ingress pg configuration for lossless pgs.
2. Stop putting ports into speed sets, put all ports in one set.
3. Remove ingress lossless profiles.
4. Added some tailing '-' back to remove leading spaces.
* Reduce SONiC migration partition from 8G to 1G.
* Changes to create 1G partition with ability to resize post migration.
* Remove redundant changes in varlog
* Use findfs to interpret root. Move resize in case cmdline params are reordered
- What I did
Updating SDK version from 3.16.0-4 to 3.16.0-5
- How I did it
Updating SDK version in files/build_templates/swss.service.j2
- How to verify it
Checking command "config load_minigraph" without errors
- Description for the changelog
Updating SDK version from 3.16.0-4 to 3.16.0-5 in swss.service.j2
- A picture of a cute animal (not mandatory but encouraged)
Signed-off-by: Sam Yang <yang.kaiyu@gmail.com>
* Upgrade linux-image version
* Add missing dependency of igb
* Fix mft build rule
* Add missing dependency of ixgbe
* [Broadcom]: Update OpenNSL modules to be compatible with kernel 3.16.0-5 (#3)
* [Nephos] Update SDK version to support new kernel module 3.16.0-5 (#4)
* [mellanox]: Update URL for SDK (#5)
When teamd service restarted, the port channels will be recreated.
Dhcp relay service needs to be restarted after that to listen on the
right port channels.
* Add switch ASIC vendor and platforms for Nephos
- What I did
Add switch ASIC vendor: Nephos
Add Nephos platforms: Ingrasys S9130-32X, Ingrasys S9230-64X
- How I did it
Add platform/nephos files
Add platform/nephos/sonic-platform-modules-ingrasys submodule
Add device/ingrasys/x86_64-ingrasys_s9130_32x-r0 files
Add device/ingrasys/x86_64-ingrasys_s9230_64x-r0 files
Add SONiC to support Nephos platform
- How to verify it
To build SONiC installer image and docker images, run the following commands:
make configure PLATFORM=nephos
make target/sonic-nephos.bin
Check system and network feature is worked as well
- Description for the changelog
Add switch ASIC vendor and platforms for Nephos
- A picture of a cute animal (not mandatory but encouraged)
Signed-off-by: Sam Yang <yang.kaiyu@gmail.com>
* Advance sonic-sairedis submodule to include #271 (Add Nephos ASIC)
snmp.service needs to read chassis serial number for one of its mibs.
We save this value in state DB so that it is accessible from container.
Signed-off-by: marian-pritsak <marianp@mellanox.com>
* [TACACS+]: Add configDB enforcer for TACACS+
* hostcfgd - configDB enforcer for TACACS+, listen configDB to
modify the pam configuration for Authentication in host
* Add a service script for hostcfgd
Signed-off-by: Chenchen Qi <chenchen.qcc@alibaba-inc.com>
* [TACACS+]: Generate conf file by template file
* Generate common-auth-sonic and tacplus_nss.conf by jinja2 template
Signed-off-by: Chenchen Qi <chenchen.qcc@alibaba-inc.com>
* [TACACS+]: Add support for TACACS+ Authentication
* pam_tacplus - A TACACS+ protocol client library and PAM module to
supports core TACACS+ functions for AAA.
* nss_tacplus - A NSS plugin for TACACS+ to extend function getpwnam,
make the TACACS+ authenticated user which is not found in local
could login successfully.
* Add make rules for pam_tacplus and install script
* Add a patch for pam_tacplus to disable pam-auth-update pam-tacplus
by default
* Add a patch for pam_tacplus to inlucde and build nss_tacplus
Signed-off-by: chenchen.qcc@alibaba-inc.com
* [TACACS+]: Add nss-tacplus as a separate src repo
* Separate nss-tacplus from pam-tacplus, modify tacacs.mk and
makefile, add a patch to adapt to the new user map profile.
* Use the lastest stable version for pam-tacplus, add a dependent
package in sonic-salve, add two patches to fix build error.
* Add scripts to disable tacplus by default.
* Remove hostcfgd service file
Signed-off-by: Chenchen Qi <chenchen.qcc@alibaba-inc.com>
* [TACACS+]: Fix nss-tacplus filter some valid TACACS+ username
* The NAME_REGEX for username check in plugin nss-tacplus is
the ANSI version "^[0-9a-zA-Z_-\ ]*$", but the regular expression
in /etc/adduser.conf is not defined as ANSI version. To avoid
nss-tacplus filter some valid TACACS+ username, remove username
check.
Signed-off-by: Chenchen Qi <chenchen.qcc@alibaba-inc.com>
If device MAC is added to init_cfg.json, it has to be done using
intermediate file. We cannot redirect to same file while trying to read
from it because it will be truncated first.
Signed-off-by: marian-pritsak <marianp@mellanox.com>
* [init]: save the initial switch mac to config db
Save the initial switch mac to config db DEVICE_METADATA|localhost entry.
* update sonic-swss submodule
* Add support for vlanconfd and intfconfd
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Change name to vlanmgrd and intfmgrd
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Add missing vlan_members for parse_dpg result
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Remove cfgmgr debug CLI from image
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Update swss and swss-common submodules for VLAN trunk support
Signed-off-by: Jipan Yang <jipan.yang@alibaba-inc.com>
* Bump sonic-platform-modules-arista
Improves i2c performance for xcvrs
Fix the led_plugin by ignoring unknown ports
Miscellaneous improvements
* Fix index column for Arista-7260CX3-D108C8
* Fix flash permissions for Arista platforms
The ext4 flash uses acl to properly handle permissions in EOS.
Aboot isn't built with this support and therefore can't be used
to set the flash permissions. It has to be deferred in sonic initrd.
* [Arista]: Fix the udev waiting in networking start
This change is to fix the issue in https://github.com/aristanetworks/sonic/issues/16
For the checking condition used, it is only applied to Arista switches
Signed-off-by: Boyang Yu <byu@arista.com>
* [Arista]: Correct for PR comments
Signed-off-by: Boyang Yu <byu@arista.com>
When updategraph service is enabled, a special value 'default'
from DHCP response will now initialize the system with an empty
configuration instead of existing minigraph.
A DHCP response without option 224 will remain the current behavior
of skipping graph update and use existing default minigraph.
* [build]: sonic-utilities package now depends on swsssdk; add build dependency
* Now building sonic-utilities Python package in wheel format
* Update sonic-utilities submodule
* Change output wheel name to match proper format
* Framework to plugin Organization specific scripts
* Framework to plugin Organization specific scripts
* Framework to plugin Organization specific scripts
* add getopt option to organization script
Existing dockers has paths mounted according to the HWSKU. When HWSKU
changes, these dockers need to be destroyed and recreated with the
correct paths mounted.
Modify minigraph parser output format so it fit DB schema
Modify configuration templates to fit new schema
Systemd services dependencies are modified so database starts before any configuration consumer
* [rsyslog]: Use timegenerated instead of timestamp
This is useful when rsyslog is used to put markers generated on other machines.
This way all messages will have a timestamp from a single system.
* [rsyslog] Use subseconds from local machine
moving to initramfs unifies disk allocate on different platforms.
use fallocate instead of dd to speed up the disk allocation.
By default, mkfs.ext4 has -E discard option which discards the blocks
at the mkfs time, also speed up the initialization time.
1. "make target/sonic-broadcom.raw" will create the compressed dd'able image.
2. This will also update the grub config files (device/dell/*/nos_to_sonic_grub.cfg) with the image versions.
- Force log rotation at size thresholds only (no longer also rotating logs daily), allowing for more consistent archived log size
- Eliminate remaining duplicate log messages
- Cron facility now only logs to cron.log (was also logging to syslog)
- Debug, mail, news and user log facilities only log to syslog; no longer creating separate log files for these facilities
- Cron job that calls logrotate every minute now uses the main /etc/logrotate.conf file so as to check/rotate all logs every minute, not just the logs specified in the rsyslog file. Also redirecting output of this command to /dev/null to prevent "(CRON) info (No MTA installed, discarding output)" messages in cron.log due to lack of a mail service
- Delete archive files based on remaining /var/log partition space. Note that this solution currently requires a minimum /var/log partition size of 32MB to function correctly
- Update sonic-sairedis and sonic-swss submodules to incorporate recording file name changes
- Add .screen file to .gitignore (unrelated)
* [cfggen] Support reading from and writing to configdb
* [bgp] Move bgp_admin_state to configdb, support dynamic admin state change
* [sonic-utilities] Adapt configDB for admin status, support config save and config load
* [bgp] Save admin state and set default state to shutdown
* Set default behavior to no shutdown
* Add build option SHUTDOWN_BGP_ON_START
* Script change for default admin state to be on
* Address CR comments to bgp_neighbor script
* Fix script bug
* Bump sonic-platform-modules-arista submodule
* Use sonic_sfputil plugin from the arista library
* Fix undefined variable varlog_size
* Prevent minigraph.xml to be removed from the flash
* Update DCS-7050QX-32 sensors config
If routes are inserted in main table, they wont' be overwritten
by the routes learned via BGP. Then the routes will be missing
from the ASIC.
Thus a default table is used so that control plane and data plane
routes are isolated and could be configured independently.
- Now that logrotate is a cron job that runs every minute, it was polluting syslog
- Also shrink max size of less-important logs to 50MB and rotate them daily by default
* [rc.local]: Copy saved minigraph if available.
In case of sonic-to-sonic update old image stores minigraph under /host
directory. Upon first boot this minigraph will be used by new image to
save configuration.
Signed-off-by: marian-pritsak <marianp@mellanox.com>
- rsyslog logs were being rotated regardless of whether they exceeded their maixmum size. This was due to "-f" flag passed to logrotate in cron job.
- After rotation, /var/log/syslog was never written to again. Instead, logs were written to /var/log/syslog.1. This was due to rsyslog not properly closing the file descriptor to the pre-rotated log.
- Also brought back time-related rotation via the new(er) maxsize option, which performs a boolean OR operation. If the log exceeds the maxsize OR the log hasn't been rotated in the specified, it will be rotated. Using the older size option, the time-based rotation was ignored.
- Also addresses issue #528
* Rename 'ACSFileFormat' -> 'SONiCFileFormat'
* Rename '00-acs.conf' -> '00-sonic.conf'
* Add logrotate.d and systemd-journald config files to image
* Log all SONiC process messages to /var/log/syslog; prevent duplicate logging to /var/log/messages
* Do not redirect cron and daemon logs to their own files, let them log to /var/log/syslog
* Log all teamd messages to /var/log/teamd.log; Add more SONiC program names to SONiC rules clause
* Remove duplicate code by condensing quagga programs into a list; Fix teamd log rule
* Kernel and LPR messages no longer getting duplicated to their own log files
* Now calling logrotate every minute via cron job
* Need full path to logrotate in cron job
* Add '.log' suffix to wildcards, otherwise logrotate will rotate already-rotated logs (e.g., bgpd.log.1.1.1.1.1...)
* Add microsecond granularity to syslog messages
* Don't overwrite system crontab, instead, install additional logrotate crontab file into /etc/cron.d
* Removed incomplete concept of per-process SONiC logs. We can revisit again later
* [device]: Add support for Mellanox MSN2410
MSN2410 runs on Spectrum silicon and has 56 ports:
48 25GbE and 8 100GbE
* Avoid full path within bash -c
Signed-off-by: marian-pritsak <marianp@mellanox.com>
- Do not bring up LAG member ports when LAG is not created.
This is because LAG member ports must be DOWN when joining
the teamd instances due to teamd design. Therefore, we cannot
bring up a LAG member port first and then join the port to a LAG.
Signed-off-by: Shuotian Cheng <shuche@microsoft.com>
* [build]: Include SONiC version into installer.
Signed-off-by: marian-pritsak <marianp@mellanox.com>
* Append dirty if contains local changes
Signed-off-by: marian-pritsak <marianp@mellanox.com>
* Update config
* Use correct name for kernel version field
* Update sysDescription.j2
- This change is added so that when doing ifdown/ifup to flap the
interface, it will success even when the interface is already
enslaved as a member of VLAN.
- LAG members do not have IP addresses. Thus ifconfig command is
needed.
- Do not display comments when not necessary.
Signed-off-by: Shuotian Cheng <shuche@microsoft.com>
* [base image]: Install SwSS SDK Python packages (Python 2 & 3) into base image
* Fix typo in existing variable name
* Only install Python 2 version, as Python 3 is not installed in base image
* [Aboot]:remove no need files before extract image
Signed-off-by: Sihui Han <sihan@microsoft.com>
* use and remove boot0 in the check
Signed-off-by: Sihui Han <sihan@microsoft.com>
* change the comments accordingly
Signed-off-by: Sihui Han <sihan@microsoft.com>
- This change ensures that when shuting down, opennsl-modules will
not stop until swss stops. Otherwise it will cause kernel stack
trace.
Signed-off-by: Shuotian Cheng <shuche@microsoft.com>
- Create /var/run/redis/ folder on the host
- Install Python client for Redis on the host
- Mount /var/run/redis/ as read/write from host for all dockers
- Enable accessing the database everywhere including on the host and from remote
Signed-off-by: Shuotian Cheng <shuche@microsoft.com>
When Type=simple, systemd will consider the service activated immediately
after specified in ExecStart process is started. If there is downstream
service depending on the state prepared in ExecStart, there will be race condition.
For example, issue #390. In this case, database.service calls database.sh, which
calls docker run or docker start -a to start database container. However, systemd
considers database.service successfully started at the time database.sh begins,
not after docker run finishes. As database.service is consider started, bgp.service
can be started. The redis database, which bgp service depends on, might or might not
have been started at this time point.
To fix this issue (and still keeping the functionality to monitor docker status with
systemd), we split the ExecStart process into an ExecStartPre part and an ExecStart
part. docker run is splitted into docker run -d then docker attach , while docker start
-a is splitted into docker start and then docker attach. In this way, we make sure
the downstream services are blocked until container is successfully started.
The reason is that /etc/network/interfaces file is in base image. After booting,
docker-swss is not ready and thus the empty VLAN interfaces cannot be created
when the brctl is pointing to the binary inside the swss docker.
Add the bridge-utils into the base image and add bridge_ports none to the
/etc/network/interfaces file so that after boot-up the empty VLAN interfaces
will be created to let the members to join later.
Signed-off-by: Shuotian Cheng <shuche@microsoft.com>
* [files]: Add allow-hotplug stanza to interfaces files
- start interface <interface_name> when the kernel detects
a hotplug event from the interface
ref: https://www.debian.org/doc/manuals/debian-reference/ch05.en.html
* [interfaces]: Combine vlan_interfaces and lag_interfaces file and add allow-hotplug
1. Remove vlan_interfaces and lag_interfaces file and members in teamd.j2
2. Add all interfaces to /etc/network/interfaces file
3. Add allow-hotplug stanza
4. Add up <command> to automatically add interfaces to VLAN and LAG
5. Add unique_name filter to minigraph.py to remove duplicate interface names
6. Add brctl to base image
7. Update sonic-swss submodule
Signed-off-by: Shuotian Cheng <shuche@microsoft.com>
Current implementation of swss and syncd causes a lot
of problems in terms of dependencies and synchronization.
Instead of handling them in separate services, we now
start and stop them both as a single entity.
Signed-off-by: marian-pritsak <marianp@mellanox.com>
( All device-specific files now reside under /device directory in a <vendor-name>/<platform-string>/<hardware-SKU> directory structure in repo.
* Device-specific files are now packaged into a Debian package (sonic-device-data) and are now installed to /usr/share/sonic/device/<platform-string>/<hardware-SKU>/ directory on switch.
- Add a functionality to get SNMP community from DHCP (option 224)
- Add a functionality to get minigraph from http service instead of using default minigraph
- The url for graph service is passed through DHCP option 225
- This feature is by default disabled. Modify rule/config to enable it on build time, or modify /etc/sonic/graph_service_url on run time.
- Fix a bug that getting hostname from DHCP is not working correctly
On some platforms after the initramfs init scripts have mounted the root device its
block device disapear from /dev. The union-mount script therefore can't mount the
root device over the aufs. If this case happen, issue a rescan of the devices to
repopulate the /dev filesystem.
- Refactor of the whole script for readability purpose
- Now detect the root= partition automatically
- Allow more parameters to be passed to the cmdline using
/mnt/flash/kernel-params
- /host/machine.conf file will have to be generated at a later stage
since Aboot doesn't have enough information about the platform here
* Single image
* Fix review comments
* Update syncd service. Add HW mgmt to Mellanox single image.
* Add single image template for Broadcom platform.
SKU should be provided during configure:
make configure PLATFORM=broadcom SKU=Force10-S6000
* Add single image template for Cavium platform.
SKU should be provided during configure:
make configure PLATFORM=cavium SKU=AS7512
* Add description to sonic_debian_extension.j2 file.
This commit will convert the existing file system of flash drive on Arista switches from VFAT to EXT4 in the booting of SONiC. It will take the whole flash and therefore remove the recovery partition. There is a check in the script making sure that the conversion operation will not happen on a non-Arista switch or if the existing file system is not VFAT.
