* sdk debs are now downloaded as Spectrum-SDK-Drivers-SONiC-Bins release
* sx kernel is downloaded as zip from Spectrum-SDK-Drivers
Signed-off-by: Yakiv Huryk <yhuryk@nvidia.com>
Why I did it
Platform cases test_tx_disable, test_tx_disable_channel, test_power_override failed in dx010.
How I did it
Add i2c access algorithm for CPLD i2c adapters.
How to verify it
Verify it with platform_tests/api/test_sfp.py::TestSfpApi test cases.
- Why I did it
Advance hw-mgmt service to V.7.0020.4100
Add missing thermal sensors that are supported by hw-mgmt package
Delay system health service before hw-mgmt has started on Mellanox platform in order to avoid reading some sensors before ready.
Depends on sonic-net/sonic-linux-kernel#305
- How I did it
1. Update hw mgmt version
2. Add missing sensors
3. Delay service
- How to verify it
Regression test.
Signed-off-by: Stephen Sun <stephens@nvidia.com>
Why I did it
Code drop with incremental fixes for Cisco 8808 and Cisco 8101-32FH-O platforms
Support for ordered ECMP capability
Support for BFD Serviceability CLI
Support for VxLAN Serviceability CLI
Support for 200G Fabric port speed for Fabric Card 8808-FC0 and Line Card 88-LC0-36FH-M/88-LC0-36FH-MO
PFC support for Q200 ASIC based line cards
Support for Single-TOR and Dual-TOR on Cisco 8102-64H-O Platform
How I did it
update cisco 8000 tag
How to verify it
Fixes#13568
Backport of #13837
Upgrade from old image always requires squashfs mount to get the next image FW binary. This can be avoided if we put FW binary under platform directory which is easily accessible after installation:
admin@r-spider-05:~$ ls /host/image-fw-new-loc.0-dirty-20230208.193534/platform/fw-SPC.mfa
/host/image-fw-new-loc.0-dirty-20230208.193534/platform/fw-SPC.mfa
admin@r-spider-05:~$ ls -al /tmp/image-fw-new-loc.0-dirty-20230208.193534-fs/etc/mlnx/fw-SPC.mfa
lrwxrwxrwx 1 root root 66 Feb 8 17:57 /tmp/image-fw-new-loc.0-dirty-20230208.193534-fs/etc/mlnx/fw-SPC.mfa -> /host/image-fw-new-loc.0-dirty-20230208.193534/platform/fw-SPC.mfa
- Why I did it
202211 and above uses different squashfs compression type that 201911 kernel can not handle. Therefore, we avoid mounting squashfs altogether with this change.
- How I did it
Place FW binary under /host/image-/platform/mlnx/, soft links in /etc/mlnx are created to avoid breaking existing scripts/automation.
/etc/mlnx/fw-SPCX.mfa is a soft link always pointing to the FW that should be used in current image
mlnx-fw-upgrade.sh is updated to prefer /host/image-/platform/mlnx location and fallback to /etc/mlnx in squashfs in case new location does not exist. This is necessary to do image downgrade.
- How to verify it
Upgrade from 201911 to 202205
202205 to 201911 downgrade
202205 -> 202205 reboot
ONIE -> 202205 boot (First FW burn)
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
- Why I did it
sfp_event.py gets a PMPE message when a cable event is available. In PMPE message, there is no label port available. Current sfp_event.py is using sx_api_port_device_get to get 64 logical ports attributes, and find the label port from those 64 attributes. However, if there are more than 64 ports, sfp_event.py might not be able to find the label port and drop the PMPE message.
- How I did it
Don't use hardcoded 64, get logical port number instead.
- How to verify it
Manual test
Co-authored-by: Junchao-Mellanox <57339448+Junchao-Mellanox@users.noreply.github.com>
add SEU reporting on chassis
fix fallback logic for Clearlake eeprom identification
fix fan speed reporting for a specific model
move pcie timeout configuration for Upperlake in platform code (deprecates hwsku-init)
* Why I did it
Enable Test sai api on bfn container with a lightweight container(saiserver).
[SAI-PTF][mlnx]Enable saiserver test container on mlnx container
How I did it
enable saiserver container on mlnx platform.
add docker-saiserver-mlnx.mk for building saiserver container
in platform/barefoot/docker-saiserver-mlnx, add necessary files that needs in saiserver container
How to verify it
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
Why I did it
Command "sudo sfputil show error-status -hw" shows "OK (Not implemented)" in the output.
How I did it
Add a new SFP API get_error_description support in Nokia sonic-platform sfp.py module.
How to verify it
Run the new image and execute command "sudo sfputil show error-status -hw"
Co-authored-by: Pavan-Nokia <120486223+Pavan-Nokia@users.noreply.github.com>
Why I did it
High CPU utilization by entropy.py
How I did it
Remove entropy script as it does not work anymore and is no longer needed for bullseye(202205).
In Buster(202012) the max available poolsize (entropy_avail) for entropy is 4096 and our entropy.py script was based on this value. With the change in kernel to bullseye on 202205 this entropy poolsize was changed to 256 which also causes our script to fail.
This script was initially added to provide SW assistance to improve the system entropy value available early on in the Sonic boot sequence on buster.
On bullseye (Linux kernel 5.10) this is no longer needed as this feature has been improved.
How to verify it
run "top" command to check CPU usage.
Co-authored-by: Pavan-Nokia <120486223+Pavan-Nokia@users.noreply.github.com>
- Why I did it
Added platform specific script to be invoked during SAI failure dump. Added some generic changes to mount /var/log/sai_failure_dump as read write in the syncd docker
- How I did it
Added script in docker-syncd of mellanox and copied it to /usr/bin
- How to verify it
Manual UT and new sonic-mgmt tests
Co-authored-by: Sudharsan Dhamal Gopalarathnam <dgsudharsan@users.noreply.github.com>
* Enable marvell-armhf saiserver docker
Signed-off-by: zitingguo-ms <zitingguo@microsoft.com>
* fix libsaithriift build env
Signed-off-by: zitingguo-ms <zitingguo@microsoft.com>
* fix thrift 014 dependent issue in armhf
* fix build env
Signed-off-by: zitingguo-ms <zitingguo@microsoft.com>
* [sai_ptf]fix thrift armhf build
in armhf buidl failed as no python command
how
add a checker for different python command, python/python3 and base on result use the right command
verify
container build
* [Thrift_014[armhf]]Fix libboost_unit_test_framework.a not found during build
Why
error happen build thirft in armhf
How
fix this issue, add a soft link for the dependent file
Verify
Build pipeline
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
* add metadata dependence
Signed-off-by: zitingguo-ms <zitingguo@microsoft.com>
* change build pipeline
Signed-off-by: zitingguo-ms <zitingguo@microsoft.com>
---------
Signed-off-by: zitingguo-ms <zitingguo@microsoft.com>
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
Co-authored-by: richardyu-ms <richard.yu@microsoft.com>
Why I did it
To pick up the below DNX fixes:
CS00012275689: DSCP->TC and TC->QUEUE mappings are not happening for packets received on LAG ports (SONIC-69367)
CS00012277618: Crash in _brcm_sai_dnx_irpp_port_core_get (SONIC-70001)
How I did it
Updated SAI branch with the above fixes
How to verify it
Ran basic sonic-mgmt tests with the SAI debian on XGS and DNX platforms
Why I did it
[Seastone] Enhancement fix for PR12200 syseeprom issue.
How I did it
Enhance the fix through replace the hardcoded devnum to bash variable
How to verify it
show platform syseeprom or decode-syseeprom
Co-authored-by: Ikki Zhu <79439153+qnos@users.noreply.github.com>
add module reboot APIs for chassis
add supervisor module on linecard (fixes show chassis module midplane-status)
improve RTC update mechanism and sync every 10 mins
fix sbtsi temp sensor presence/thresholds
fix Mineral status leds
remove thermal object on xcvrs
misc fixes
- Why I did it
To include latest fixes and new functionality
SAI
1. Temporary WA for query enum capabilities for tunnel peer mode, to not return P2P
2. sai debug dump returns while last extra dump is running
3. open inner SRC and DST IP for ECMP / LAG general hash objects
4. tunnel peer mode returns hard coded
5. tunnel decap dscp mode
6. support default tunnel src ip
7. failure to add a port to a LAG in VLANs configured with flood_ctrl
8. Add P2P peer mode for IP in IP tunnels
9. Add per port IP counters
10. Clean up VXLAN srcport static (XML) functionality, as only dynamic (API) is in use
11. Fix enum capabilities of native hash fields
12. sai_acl_db_group_ptr usage
13. Clean QoS config of the LAG when all members was removed (bug
SDK/FW
1. Fixed bug in recovery mechanism in case of I2C error when trying to access the XSFP module.
2. On the NVIDIA Spectrum-2 switch, when receiving a packet with Symbol Errors on ports that are configured to cut-thought mode, a pipeline might get stuck.
3. On the Spectrum-2 and Spectrum-3 switch, if you enable ECN marking and the port is in split mode, traffic sent to the port under congestion (for example, when connecting two ports with a total speed of 50GbE to a single 25GbE port) is not marked.
4. Modifying existing entry/Adding new one when switch is at its maximum capacity (full by maximum allowed entries from any type such as routes, FDB, and so forth), will fail with an error.
5. When many ports are active (e.g., 70 ports up), and the configuration of shared buffer is applied on the fly, occasionally, the firmware might get stuck.
6. When a system has more than 256 ACL rules, on rare occasion, removing/adding rules may cause some ACL rules not to work.
7. On SN2201 system, on RJ45 port, the link might appear in 'down' state even if it operations properly.
8. Layer 4 port information is not initialized for BFD packet event. To address the issue, remote peer UDP port information was added in BFD packet event.
9. When setting LAG as a SPAN analyzer, the distributor mode of the LAG members was not taken into account. It may happen that the LAG member with distributor mode disabled will be set as a SPAN analyzer port.
- How I did it
Updated SDK/SAI submodule and relevant makefiles with the required versions.
- How to verify it
Build an image and run tests from "sonic-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
Why I did it
To bring in the following fixes:
Revert temporary fix added to disable SA equal DA drops
CS00012273013 - [7.1][J2, J2c+] Disable SA Equals DA trap on DNX
CS00012274222 - How to block the voq for given destination port for a flow from a remote mod-id
CS00012275381 - SAI_INGRESS_PRIORITY_GROUP_STAT_PACKETS is incremented for port's PG's even if there are no traffic sent to that PG
CS00012274433 - Local Fault and Remote Fault are not polled by linkscan thread
How I did it
Merged above fixes to SAI code
How to verify it
Validated by running the basic sanity tests on XGS and DNX chassis platforms including
fib/test_fib.py
decap/test_decap.py
drop_counters/test_drop_counters.py
arp/test_arpall.py
- Why I did it
To include latest fixes and new functionality
* SAI
1. Temporary WA for query enum capabilities for tunnel peer mode, to not return P2P
2. sai debug dump returns while last extra dump is running
3. open inner SRC and DST IP for ECMP / LAG general hash objects
4. tunnel peer mode returns hard coded
5. tunnel decap dscp mode
6. support default tunnel src ip
7. failure to add a port to a LAG in VLANs configured with flood_ctrl
8. Add P2P peer mode for IP in IP tunnels
9. Add per port IP counters
10. Clean up VXLAN srcport static (XML) functionality, as only dynamic (API) is in use
11. Fix enum capabilities of native hash fields
12. sai_acl_db_group_ptr usage
13. Clean QoS config of the LAG when all members was removed (bug
* SDK/FW
1. Fixed bug in recovery mechanism in case of I2C error when trying to access the XSFP module.
2. On the NVIDIA Spectrum-2 switch, when receiving a packet with Symbol Errors on ports that are configured to cut-thought mode, a pipeline might get stuck.
3. On the Spectrum-2 and Spectrum-3 switch, if you enable ECN marking and the port is in split mode, traffic sent to the port under congestion (for example, when connecting two ports with a total speed of 50GbE to a single 25GbE port) is not marked.
5. Modifying existing entry/Adding new one when switch is at its maximum capacity (full by maximum allowed entries from any type such as routes, FDB, and so forth), will fail with an error.
6. When many ports are active (e.g., 70 ports up), and the configuration of shared buffer is applied on the fly, occasionally, the firmware might get stuck.
7. When a system has more than 256 ACL rules, on rare occasion, removing/adding rules may cause some ACL rules not to work.
8. On SN2201 system, on RJ45 port, the link might appear in 'down' state even if it operations properly.
9. Layer 4 port information is not initialized for BFD packet event. To address the issue, remote peer UDP port information was added in BFD packet event.
10. When setting LAG as a SPAN analyzer, the distributor mode of the LAG members was not taken into account. It may happen that the LAG member with distributor mode disabled will be set as a SPAN analyzer port.
- How I did it
Updated SDK/SAI submodule and relevant makefiles with the required versions.
- How to verify it
Build an image and run tests from "sonic-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
Why I did it
why
In order to apply different config across different platform, and use the code with a unified format, reuse syncd init script to init saiserver.
How I did it
how
Reuse syncd init script
How to verify it
Test
Test in DUT s6000 and dx010 with sonic 202205
Why I did it
Advance SAI Redis head pointer
How I did it
changes:
sonic-net/sonic-sairedis@cf679e7sonic-net/sonic-sairedis@8d6688e
[202205][Submodule][SAI]Advance SAI head pointer sonic-sairedis#1185 sonic-net/sonic-sairedis@66f2961
remove parameter --skip_error, which removed from [202205][Submodule][SAI]Advance SAI head pointer sonic-sairedis#1185
How to verify it
local image build
This PR is to backport #13100 to the 202205 branch since can not be cleanly cherry-picked.
Following code to judge whether a process is running inside a docker could get stuck on the simx platform
subprocess.Popen(["docker", "--version"],
stdout=subprocess.PIPE,
stderr=subprocess.STDOUT,
universal_newlines=True)
When it gets stuck, the config-chassisdb service can not be successfully started, thus the system can not be booted up.
root@sonic:/# service config-chassisdb status
config-chassisdb.service - Config chassis_db
Loaded: loaded (/lib/systemd/system/config-chassisdb.service; enabled; vendor preset: enabled)
Active: activating (start) since Thu 2022-12-15 09:23:02 UTC; 29min ago
Main PID: 571 (config-chassisd)
Tasks: 14 (limit: 9501)
Memory: 132.4M
CGroup: /system.slice/config-chassisdb.service
├─571 /bin/bash /usr/bin/config-chassisdb
├─575 /usr/bin/python3 /usr/local/bin/sonic-cfggen -H -v DEVICE_METADATA.localhost.platform
├─602 /bin/sh -c sudo decode-syseeprom -m
├─603 sudo decode-syseeprom -m
├─607 /usr/bin/python3 /usr/local/bin/decode-syseeprom -m
├─616 /bin/sh -c docker --version 2>/dev/null
└─617 docker --version
- How I did it
Use an alternative way to implement this function and issue can be avoided:
docker_env_file = '/.dockerenv'
return os.path.exists(docker_env_file) is False
- How to verify it
run regression on real hardware and simx platform.
Why I did it
In order to prevent the sonic-mgmt/tests/platform_tests/sfp/test_sfputil.py test failing on the log analyzer step.
The mentioned test is performing the sfputil reset EthernetX for every interface on the SONiC switch, this action will flap the SFP device status (INSTERTED -> REMOVED -> INSTERTED).
The SONiC XCVRD daemon will catch this SFP device status change (because it is monitoring the presence status of the cable).
To judge the cable presence status, currently, we are still leveraging to read the first bytes of the EEPROM, and the EEPROM could be not ready at some moment and the SONiC XCVRD daemon will print the error log to Syslog:
ERR pmon#xcvrd: Error! Unable to read data for 'xx' port, page 'xx' offset 128, rc = 1, err msg: Sending access register
How I did it
Change logging severity from ERR to WARNING
Signed-off-by: Vadym Hlushko <vadymh@nvidia.com>
Why I did it
To bring the following fixes:
Applied customer patch for limited port breakout support in rel_ocp_sai_7_1.
Revert "Merged PR 7224850: SAI7.1_DNX: Temp workaround for Nexthop Group Scale Issue(CS00012251649)".
backport SONIC-67662 to SAI7.1:JR2C ECMP partition for NHgroup members.
How I did it
Updated SAI code with the fixes above.
How to verify it
Run the SONiC and SAI test with the SAI pipeline.
Why I did it
Update Marvell armhf sai debian version. Includes supports for,
Autoneg
Everflow
How to verify it
Compile and load SONiC armhf bin
Signed-off-by: rajkumar38 <rpennadamram@marvell.com>
Why I did it
smartctl tool is available only in PMON docker. Hence, the tool may be not accessible incase PMON docker goes down.
Using iSMART_64 tool to fetch the SSD firmware version and device model information.
How I did it
Replacing smartctl with iSMART_64.
1d53bf4 Skip platform NDK health check two times in watchdog.sh
d68297c Added code to shutdown the channel after the grpc call also fixed the show fp-status command
0769efe Impelemented the module API to return the correct eeprom info for fabric card.
171569c Remove explicit logger identifier for transceiver module operations; use inherited id
6c4d651 Corrected the log messages for firmware install
Signed-off-by: mlok <marty.lok@nokia.com>
Why I did it
enable sai-ptf logger in sai_adapter to log all the sai api invcations
How I did it
add build parameter to enable the sai-ptf logger when build sai PRC
How to verify it
local build test
test the generated sai_adapter
test with pipeline
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
