To make the peer switch hostname easily accessible from config DB. Add peer_switch field to DEVICE_METADATA table
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
The HLD about MACsec feature is at :
https://github.com/Azure/SONiC/blob/master/doc/macsec/MACsec_hld.md
- How to verify it
This PR doesn't set MACsec container automatically start, You should manually start the container by docker run docker-macsec
wpa_supplicant binary can be found at MACsec container.
This PR depends on the PR, WPA_SUPPLICANT, and The MACsec container will be set as automatically start by later PR.
Signed-off-by: zegan <zegan@microsoft.com>
* Enable telemetry for ARM64 by default
* [Centec]Upgrade Centec syncd docker to buster; libjemalloc2 have been installed in docker-base-buster, remove libjemalloc1 from docker-syncd-centec's Dockerfile.j2
Co-authored-by: Gu Xianghong <xgu@centecnetworks.com>
* Use 20 and 30 route-map entries instead of 2 and 3 for TSA
* Added support for dynamic "Allow list" default action.
Co-authored-by: Pavel Shirshov <pavel.contrib@gmail.com>
**- Why I did it**
This PR aims to monitor the running status of each container. Currently the auto-restart feature was enabled. If a critical process exited unexpected, the container will be restarted. If the container was restarted 3 times during 20 minutes, then it will not run anymore unless we cleared the flag using the command `sudo systemctl reset-failed <container_name>` manually.
**- How I did it**
We will employ Monit to monitor a script. This script will generate the expected running container list and compare it with the current running containers. If there are containers which were expected to run but were not running, then an alerting message will be written into syslog.
**- How to verify it**
I tested this feature on a lab device `str-a7050-acs-3` which has single ASIC and `str2-n3164-acs-3` which has a Multi-ASIC. First I manually stopped a container by running the command `sudo systemctl stop <container_name>`, then I checked whether there was an alerting message in the syslog.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
In scenario where upgrade gets config from minigraph, it could miss tacacs credentials as they are not in minigraph. Hence restore explicitly upon load-minigraph, if present.
- Why I did it
Upon boot, when config migration is required, the switch could load config from minigraph. The config-load from minigraph would wipe off TACACS key and disable login via TACACS, which would disable all remote user access. This change, would re-configure the TACACS if there is a saved copy available.
- How I did it
When config is loaded from minigraph, look for a TACACS credentials back up (tacacs.json) under /etc/sonic/old_config. If present, load the credentials into running config, before config-save is called.
- How to verify it
Remove /etc/sonic/config_db.json and do an image update. Upon reboot, w/o this change, you would not be able ssh in as remote user. You may login as admin and check out, "show tacacs" & "show aaa" to verify that tacacs-key is missing and login is not enabled for tacacs.
With this change applied, remove /etc/sonic/config_db.json, but save tacacs & aaa credentials as tacacs.json in /etc/sonic/. Upon reboot, you should see remote user access possible.
- Make PDDF code compliant with both Python 2 and Python 3
- Align code with PEP8 standards using autopep8
- Build and install both Python 2 and Python 3 PDDF packages
Pass universal_newlines=True parameter to subprocess.Popen(); no longer use .encode('utf-8') on resulting stdout.
This was missed in #5886
Note: I would prefer to use text=True instead of universal_newlines=True, as the former is an alias only available in Python 3 and is more understandable than the latter. However, Even though the setup.py file for this package only specifies Python 3, the LGTM tool finds other Python 2 code in the repo and validates the code as Python 2 code and alerts that text=True is an invalid parameter. Will stick with universal_newlines=True for now. Once all Python code in the repo has been converted to Python 3, I will change all universal_newlines=True to text=True.
Starting from build (master) 176 the warm reboot on BRCM Platform started to experience syncd crash. Upon further debug by Ying it was determined that the crash was related to the following new change:
[Dynamic buffer calc] Support dynamic buffer calculation (#1338)
Ying also debugged further and found The crash was caused by buffer pool profile setting operation SAI_BUFFER_PROFILE_ATTR_SHARED_DYNAMIC_TH
A case has filed with BRCM while a potential fix was tried by Ying that seems to have addressed this issue and we are making this change available in master branch so that it will allow further feature validation/testing especially in the warm reboot area.
Once an official fix is provided by BRCM, we will then remove this in house fix and apply the official fix.
- How to verify it
Just perform warm reboot with any master code 175 or above you should see this issue or issue the following cmd will also cause the crash: "mmuconfig -p egress_lossy_profile -a 0"
src/sonic-platform-common 9935fca...8664efc (2):
Make sonic_sfp Python2 and Python3 compatible (#157)
[sffbase.py] Fix to make Python 3-compatible (#156)
src/sonic-platform-daemons e6c786b...81318f7 (1):
[psud] Fix issue where PSU Fan info is not updated in State DB (#137)
Fixes#6341
- Dynamically change EEPROM driver based on media type.
- Otherwise, EEPROM INFO and DOM INFO might not be fetched properly and will result in erroneous output.
To incldue following changes:
- [ci]: add build for arm64 and armhf (#757)
- Use template hgetall, because we will tune the return types of library functions (#759)
- [syncd] Fix bulk multi attrs for same key db update (#761)
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
Enable the notify mode of rsyslogd imfile module used for supervisord
logs in docker container.
Setup the mode="inotify" when loading imfile, made sure we are are getting
supervisord logs in host immediately.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
**- Why I did it**
I'm updating the jinja2 template to support getting SNMP information from the redis configdb.
I'm using the format approved here:
https://github.com/Azure/SONiC/pull/718
This will pave the way for us to decrement using the snmp.yml in the future.
Right now we will still be using both the snmp.yml and configdb to get variable information in order to create the snmpd.conf via the sonic-cfggen tool.
**- How I did it**
I first updated the SNMP Schema in PR #718 to get that approved as a standardized format.
Then I verified I could add snmp configs to the configdb using this standard schema. Once the configs were added to the configdb then I updated the snmpd.conf.j2 file to support the updates via the configdb while still using the variables in the snmp.yml file in parallel. This way we will have backward compatibility until we can fully migrate to the configdb only.
By updating the snmpd.conf.j2 template and running the sonic-cfggen tool the snmpd.conf gets generated with using the values in both the configdb and snmp.yml file.
Co-authored-by: trvanduy <trvanduy@microsoft.com>
- Why I did it - Reboot cause prints "Non-Hardware (N/A)" instead of showing the software reboot cause.
The issue is mishandling of hardware reboot cause in determine-reboot-cause script.
- How I did it
Fixed the handling for Non Hardware reboot cause. Ignore if Non-Hardware is present in the hardware_reboot_cause output. Added some code refactoring for simplicity.
- How to verify it - With fix, the hardware reboot cause is ignored (if it is non hw):
The details are as follows:
1. 0010-Ported-fix-for-length-exceeded-from-lldp-community.patch
Patch taken from 78243478dc
lib: remove limit on system description length
The limit was introduced in 9c49ced while fixing a memory leak.
The state data is used to ensure we don't interleave operations. We
need to handle the case where the value is truncated because it is
larger than the allocated size.
Fix issue https://github.com/lldpd/lldpd/issues/408
2. 0011-fix-med-location-len.patch
Patch taken from 5c3479463a
lib: fix LLDP-MED location parsing in liblldpctl
Some bounds were not checked correctly when parsing LLDP-MED civic
location fields. This triggers out-of-bound reads (no write) in
lldpcli, ultimately leading to a crash.
Fix https://github.com/lldpd/lldpd/pull/420
Signed-off-by: sudhanshukumar22 <sudhanshu.kumar@broadcom.com>
combine multiple same operation into one operation to reduce
the build steps. this is to avoid max depth exceeded issue
in the build.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Add a systemd dependency to make platform-modules service as a prerequisite for determine-reboot-cause service to ensure platform initialization is complete before determine-reboot-cause.service executes.
In the emulated armhf environment, the function readdir()returns NULL on a ext4 file system directory. When running the libyang1 test cases, it will require to load the plugins from the files (such as metadata.so), because the readdir() is failing, the plugins can’t be loaded in the emulated armhf environment, so it causes libyang1 test error. This error is a combination of the following reasons.
• Emulation of a 32-bit target from a 64-bit host –> qemu from x86_64 to armhf
• Glibc version > 2.27 – Debian buster is using glibc 2.28
- How I did it
Enabled large file support by setting _FILE_OFFSET_BITS=64 for libyang1.
Signed-off-by: Sabareesh Kumar Anandan <sanandan@marvell.com>
build frr dbg image force to install frr in the build process
which breaks the current build and is uneccessary.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
the control file version is 4.2.1.5-7
sonic$ sudo dpkg -i target/debs/buster/libsaibcm-dev_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm-dev_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm-dev (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm-dev (4.2.1.5-7) ...
lgh@491d842369cf:/sonic$ sudo dpkg -i target/debs/buster/libsaibcm_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm (4.2.1.5-7) ...
Processing triggers for libc-bin (2.28-10) ...
Signed-off-by: Guohan Lu <lguohan@gmail.com>
frr build requires libyang 1.0.184 which conflicts with
libyang 1.0.73. Solution here is to compile frr and libyang 1.0.184
first, and then uninstall libyang 1.0.184 after frr build.
Then, compile libyang 1.0.73 and all packages depend on it later.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
in case conflicting packages have same name but different version,
the install step needs to wait till package with the conflicting
version is uninstalled
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
Features:
Spectrum-3 | Systems | Added GA-level support for SN4700 A0 system
All | Shared headroom | Added GA-level support for Shared headroom between PGs
Bugs fixes:
All | Counters | Sent traffic in certain size is wrongly increase to a smaller size counter, because port extended counter has a counter for sent traffic per packet-size range
All | Shared buffer | Configuring shared buffer on the fly may, on occasion, cause the chip to get stuck
Spectrum-2 | Modules | On occasion, link down is experienced with INPHI COLORZ PAM4 100G optic cables on SN3700 systems
Including commits in sonic-swss-common repo:
b423b9c Add support for hexists call (#432) [Tony Titus]
0982996 Remove extension of tableNameSeparatorMap (#430) [Qi Luo]
d16cc76 [build]: add azure pipeline build badge (#429) [lguohan]
f2aaf55 Set up CI with Azure Pipelines (#428) [lguohan]
What: Modify unit test to not call any platform dependent api in test_find_hardware_reboot_cause.
- Why I did it
MELLANOX build is failing for the recent PRs. The errors are due to platform library being invoked in a unit test for determine-reboot-cause script.
Verified by running unit tests and a successful Mellanox build.
Co-authored-by: Vaibhav Hemant Dixit <vadixit@microsoft.com>
Why I did it
To support FG_ECMP scenarios
- How I did it
Modified minigraph parser to parse ECMP fields in the case they are present in minigraph
- How to verify it
Loaded ensuing config_db file on a DUT to verify the fields are parsed and configure device correctly
