Cherypick of #15685
MSFT ADO: 24274591
Why I did it
Two changes:
1 Fix a day1 issue, where check to wait until CONFIG_DB_INITIALIZED is incorrect.
There are multiple places where same incorrect logic is used.
Current logic (until [[ $($SONIC_DB_CLI CONFIG_DB GET "CONFIG_DB_INITIALIZED") ]];) will always result in pass, irrespective of the result of GET operation.
root@str2-7060cx-32s-29:~# sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED"
1
root@str2-7060cx-32s-29:~# until [[ $(sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED") ]]; do echo "entered here"; done
root@str2-7060cx-32s-29:~#
root@str2-7060cx-32s-29:~#
root@str2-7060cx-32s-29:~# sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED"
0
root@str2-7060cx-32s-29:~# until [[ $(sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED") ]]; do echo "entered here"; done
root@str2-7060cx-32s-29:~#
Fix this logic by checking for value of flag to be "1".
root@str2-7060cx-32s-29:~# until [[ $(sonic-db-cli CONFIG_DB GET "CONFIG_DB_INITIALIZED") -eq 1 ]]; do echo "entered here"; done
entered here
entered here
entered here
This gap in logic was highlighted when another fix was merged: #14933
The issue being fixed here caused warmboot-finalizer to not wait until config-db is initialized.
2 Set and unset CONFIG_DB_INITIALIZED for warm-reboot case
Currently, during warm shutdown CONFIG_DB_INITIALIZED's value is stored in redis db backup. This is restored back when the dump is loaded during warm-recovery.
So the value of CONFIG_DB_INITIALIZED does not depend on config db's state, however it remain what it was before reboot.
Fix this by setting CONFIG_DB_INITIALIZED to 0 as when the DB is loaded, and set it to 1 after db_migrator is done.
Work item tracking
Microsoft ADO (number only):
How I did it
How to verify it
Why I did it
Fix the issue where db_migrator is called before DB is loaded w/ config. This leads to db_migrator:
Not finding anything, and resumes to incorrectly migrate every missing config
This is not expected. migration should happen after the old config is loaded and only new schema changes need migration.
Since DB does not have anything when migrator is called, db_migrator fails when some APIs return None.
The reason for incorrect call is that:
database service starts db_migrator as part of startup sequence.
config-setup service loads data from old-config/minigraph. However, since it has Requires=database.service.
Hence, config-setup starts only when database service is started. And database service is started when db_migrator is completed.
Fixed by:
Check if this is first time boot by checking pending_config_migration flag.
If pending_config_migration is enabled, then do not call db_migrator as part of database service startup.
Let database service start which triggers config-setup service to start.
Now call db_migrator after when config-setup service loads old-config/minigraph
Why I did it
Support for SONIC chassis isolation using TSA and un-isolation using TSB from supervisor module
Work item tracking
Microsoft ADO (number only): 17826134
How I did it
When TSA is run on the supervisor, it triggers TSA on each of the linecards using the secure rexec infrastructure introduced in sonic-net/sonic-utilities#2701. User password is requested to allow secure login to linecards through ssh, before execution of TSA/TSB on the linecards
TSA of the chassis withdraws routes from all the external BGP neighbors on each linecard, in order to isolate the entire chassis. No route withdrawal is done from the internal BGP sessions between the linecards to prevent transient drops during internal route deletion. With these changes, complete isolation of a single linecard using TSA will not be possible (a separate CLI/script option will be introduced at a later time to achieve this)
Changes also include no-stats option with TSC for quick retrieval of the current system isolation state
This PR also reverts changes in #11403
How to verify it
These changes have a dependency on sonic-net/sonic-utilities#2701 for testing
Run TSA from supervisor module and ensure transition to Maintenance mode on each linecard
Verify that all routes are withdrawn from eBGP neighbors on all linecards
Run TSB from supervisor module and ensure transition to Normal mode on each linecard
Verify that all routes are re-advertised from eBGP neighbors on all linecards
Run TSC no-stats from supervisor and verify that just the system maintenance state is returned from all linecards
Why I did it
In upgrade scenarios, where config_db.json is not carry forwarded to new image, it could be left w/o TACACS credentials.
Added a service to trigger 5 minutes after boot and restore TACACS, if /etc/sonic/old_config/tacacs.json is present.
How I did it
By adding a service, that would fire 5 mins after boot.
This service apply tacacs if available.
How to verify it
Upgrade and watch status of tacacs.timer & tacacs.service
You may create /etc/sonic/old_config/tacacs.json, with updated credentials
(before 5mins after boot) and see that appears in config & persisted too.
Which release branch to backport (provide reason below if selected)
201911
202006
202012
Encounter error during "config-setup boot" if the updategraph is enabled.
How I did it
Correct the code inside the config-setup script.
Remove the space between the assignment operator.
How to verify it
Remove the /etc/sonic/config_db.json and reboot the device.
Originally, it will return following error after boot up.
rv: command not found
After modification, it can correctly parse the status of updategraph without error.
In scenario where upgrade gets config from minigraph, it could miss tacacs credentials as they are not in minigraph. Hence restore explicitly upon load-minigraph, if present.
- Why I did it
Upon boot, when config migration is required, the switch could load config from minigraph. The config-load from minigraph would wipe off TACACS key and disable login via TACACS, which would disable all remote user access. This change, would re-configure the TACACS if there is a saved copy available.
- How I did it
When config is loaded from minigraph, look for a TACACS credentials back up (tacacs.json) under /etc/sonic/old_config. If present, load the credentials into running config, before config-save is called.
- How to verify it
Remove /etc/sonic/config_db.json and do an image update. Upon reboot, w/o this change, you would not be able ssh in as remote user. You may login as admin and check out, "show tacacs" & "show aaa" to verify that tacacs-key is missing and login is not enabled for tacacs.
With this change applied, remove /etc/sonic/config_db.json, but save tacacs & aaa credentials as tacacs.json in /etc/sonic/. Upon reboot, you should see remote user access possible.
We are moving toward building all Python packages for SONiC as wheel packages rather than Debian packages. This will also allow us to more easily transition to Python 3.
Python files are now packaged in "sonic-utilities" Pyhton wheel. Data files are now packaged in "sonic-utilities-data" Debian package.
**- How I did it**
- Build and install sonic-utilities as a Python package
- Remove explicit installation of wheel dependencies, as these will now get installed implicitly by pip when installing sonic-utilities as a wheel
- Build and install new sonic-utilities-data package to install data files required by sonic-utilities applications
- Update all references to sonic-utilities scripts/entrypoints to either reference the new /usr/local/bin/ location or remove absolute path entirely where applicable
Submodule updates:
* src/sonic-utilities aa27dd9...2244d7b (5):
> Support building sonic-utilities as a Python wheel package instead of a Debian package (#1122)
> [consutil] Display remote device name in show command (#1120)
> [vrf] fix check state_db error when vrf moving (#1119)
> [consutil] Fix issue where the ConfigDBConnector's reference is missing (#1117)
> Update to make config load/reload backward compatible. (#1115)
* src/sonic-ztp dd025bc...911d622 (1):
> Update paths to reflect new sonic-utilities install location, /usr/local/bin/ (#19)
* [platform] Add Support For Environment Variable
This PR adds the ability to read environment file from /etc/sonic.
the file contains immutable SONiC config attributes such as platform,
hwsku, version, device_type. The aim is to minimize calls being made
into sonic-cfggen during boot time.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
* Changes to support config-setup service for multi-npu
platforms. For Multi-npu we are not supporting as of
now config initializtion and ZTP. It will support creating
config db from minigraph or using config db from previous
file system
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
* Address Review Comments.
* Address Review comments
* Address Review Comments of using pyhton based config load_minigraph/
config save/config reload from shell scripts so that we don't duplicate
code. Also while running from shell we will skip stop/start services
done by those commands.
* Updated to use python command so no code duplication.
and then we load image and reboot even if there was existing
config_db.json we will look for DHCP Service. we should disbale
update_graph in such cases. This behaviour is silimar to what we have in
201811 image.
* [MultiDB] (except ./src and ./dockers dirs): replace redis-cli with sonic-db-cli and use new DBConnector
* update comment for a potential bug
* update comment
* add TODO maker as review reqirement
* Create a SONiC configuration management service
* Perform config db migration after loading config_db.json to redis DB
* Migrate config-setup post migration hooks on image upgrade
config-setup post migration hooks help user to migrate configurations from
old image to new image. If the installed hooks are user defined they will not
be part of the newly installed image. So these hooks have to be migrated to
new image and only then they can be executing when the new image is booting.
The changes in this fix migrate config-setup post-migration hooks and ensure
that any hooks with the same filename in newly installed image are not
overwritten.
It is expected that users install new hooks as per their requirement and
not edit existing hooks. Any changes to existing hooks need to be done as
part of new image and not post bootup.
