* [updategraph] add support to use preset config instead of default minigraph
* Fix variable case
* Remove default minigraph case
* Remove default minigraphs and add default_sku files
for ecn on/off operations, which are conducted at per queue all interfaces granularity.
TODO:
Ideally, we should have ECN/WRED profile applied at per interface per queue
granularity, and we should do it for all hwskus under the device
directory, not just 7050.
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Update sensors.conf for 7050QX-32 and 7050QX-32S
These two platforms were using a previous version of a kernel driver.
The new one names the i2c buses differently.
We therefore need to rename them here.
* Fix the default minigraph for the 7050QX-32S
The interface offset is invalid which makes sonic-cfggen generate an
invalid config_db.jon in rc.local.
This config then silently makes orchagent/syncd fail.
* Use the partition on which sonic-aboot.swi is
Instead of always assuming /mnt/flash, use the partition where the image
to be installed lies.
This allow for the image to be on any partition.
Move the ingress lossless profile from buffers.json.j2 to pg_profile_lookup.ini
Move pool and the rest of the profile from buffers.json.j2 to
buffers_defaults_t1.j2
Add port speed info in port_config.ini
Make buffers_default_t1.j2 the default profile in buffers.json.j2
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* First part of skipping not used port for qos configuration
* Use active ports only to set QoS parameters for 6100
* Add a test for qos.json.j2
* Add a test for Dell S6100 buffers.json template
* Update submodulre
* Add Broadcom config files for Arista-7050-QX32 and Arista-7050-Q16S64 SKUs under respective directories
* Remove 'serdes_firmware_mode_xe=0x1' line from Arista 7050 Broadcom config files
* [test] Adding Broadcom configuration file test
In order to allow SONiC community to check in Broadcom configuration
file directly under device folder. We need to add this test to make
sure the contents of the configuration is compliant with Broadcom
specifications.
* Invoke test from Debian package builder
* Use $() syntax
* Remove the debug echo statement
* Reduce xoff size for in-flight packets of lossless traffic
Signed-off-by: Wenda <wenni@microsoft.com>
* Must explicitly specify min buffer size per queue to be zero
Signed-off-by: Wenda <wenni@microsoft.com>
* Improve memory utilization through more sharing at the ingress on A7050-QX-32S
Signed-off-by: Wenda <wenni@microsoft.com>
* Apply buffers config changes on A7050-QX-32S to A7050-QX32
Signed-off-by: Wenda <wenni@microsoft.com>
* Apply buffers config changes on A7050-QX-32S to S6000
* Add qos.json for Arista-7050-QX-32S
This file is a modification from the one in the swss docker, and is applied in the base image
Signed-off-by: Wenda <wenni@microsoft.com>
* Prepare buffers.json.j2 alongside with qos.json to allow qos config to take
effect on a7050-QX-32S
Signed-off-by: Wenda <wenni@microsoft.com>
* [sonic build] Define folder macro for target folder /usr/sonic/share/templates
* [sonic-cfggen] allow templates to include from common folders
- Allow templates to include files under /usr/share/sonic/templates
- Allow templates to include files in the same folder as the root template
* [Buffer config] install the buffer configuration template
* [Arista7260cx3] Add buffer configuration for Arista7260CX3 T0 topology
- pg profile look up table is incomplete. Currently contains T0 default
values.
* [Arista7260cx3] Adding QoS configuration
* Address review comments
1. Stop generating ingress pg configuration for lossless pgs.
2. Stop putting ports into speed sets, put all ports in one set.
3. Remove ingress lossless profiles.
4. Added some tailing '-' back to remove leading spaces.
