Add support for Accton as9726-32d platform
This pull request is based on as9716-32d, so I reference as9716-32d to create new model: as9726-32d.
This module do not need led driver to control led, FPGA can handle it.
I also implement API2.0(sonic_platform) for this model, CPLD driver, PSU driver, Fan driver to control these HW behavior.
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
bug fix: #5914
Validated for tx_disable function of SFP+ on AS7312-54X, AS5812-54X, AS5712-54x, and AS5812-54x.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
Fix 259 alerts reported by the LGTM tool:
- 245 for Unused import
- 7 for Testing equality to None
- 5 for Duplicate key in dict literal
- 1 for Module is imported more than once
- 1 for Unused local variable
Original converting from register is wrong, it makes the fan speed much higher than it is. Change the way fan speed is calculated from CPLD.
Signed-off-by: roy_lee <roy_lee@accton.com>
HW set qsfp port to reset at default. so need SW to set to normal when boot.
1. Modify cpld driver to invert reset offset value
2. Set to normal when boot.
**- Why I did it**
The tx_disable function isn't work for the accton_ax5835-54x device.
**- How I did it**
Fix the incorrect path of the sfp node path inside the util file.
**- How to verify it**
Test with
"sudo accton_as5835_54x_util.py show"
"sudo accton_as5835_54x_util.py set sfp"
There should see correct value for module_present and module_tx_disable. And should able to set it.
Signed-off-by: kuanyu_chen <kuanyu_chen@edge-core.com>
3y Power YPEB-1200am PSU doens't support read fan_dir from pmbus register
Check with vendor this PUS type only support F2B fan direction. So add to show "F2B"
when red psu_fan_dir sysfs.
1. undefine led_classdev_register as it is defined in leds.h
2. header file location change
a. linux/i2c/pmbus.h -> linux/pmbus.h
b. linux/i2c-mux-gpio.h -> linux/platform_data/i2c-mux-gpio.h
c. linux/i2c/pca954x.h -> linux/platform_data/pca954x.h
Due to linux create hwmonN node number, N isn't fixed. So modify to use "" to let thermal.py can correct sysfs. For example, use /sys/bus/i2c/devices/55-0048/hwmon/hwmon/temp1_input to instead of /sys/bus/i2c/devices/55-0048/hwmon/hwmon4/temp1_input
AS7326-56X and AS7726-56X use the same design so both devices have the same problem.
The detailed description below takes AS7326-56X as the example to explain.
Original implementation:
- In platform/broadcom/sonic-platform-modules-accton/as7326-56x/service/as7326-platform-handle_mac.service,
it executes the script file "accton_handle_idt.sh".
- In "accton_handle_idt.sh", it modifies the content of the script file "/etc/init.d/opennsl-modules"
to insert the lines to execute "idt_init.sh" before the command to load broadcom linux kernel module "linux-kernel-bde.ko".
- The script "idt_init.sh" cannot be executed at the first boot of SONiC after installing SONiC under ONIE. This is the reason why all of the ports does not work.
New implementation:
- Let "as7326-platform-handle_mac.service" execute "idt_init.sh".
- Change the content of "as7326-platform-handle_mac.service" to define the service type as "oneshot". Add the settings to ensure "as7326-platform-handle_mac.service" is executed before "opennsl-modules.service".
By setting the service type as "oneshot", it is guaranteed that "opennsl-modules.services" is started only when the forked process to execute the script file "idt_init.sh" is terminated
Signed-off-by: charlie_chen <charlie_chen@edge-core.com>
* Change psu driver to comfort to lm-sensors.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Duplicate fan attributes with naming conforming to lm-sensors.
Replace psu drivers.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Revise cpr_4011_4mxx.c to support lm-sensors.
Signed-off-by: roy_lee <roy_lee@accton.com>
This switch has 27 fiber ports, 4x25G, 20x10G , and 3x100G ports ports.
CPU: Intel ® Atom™ Processor C3508,1.6GHz
BMC: None
MAC: Broadcom BCM88470 (Qumran AX).
MISC: Support IEEE1588v2, hot-swappable PSU, hot-swappable fan tray.
But notice here, BCM88470 is not supported for SAI now.
So the syncd container is not running so far.
Signed-off-by: roy_lee <roy_lee@accton.com>
I2c burst read may failed due to misoperation of ir3570a(A DC-to-DC converter IC).
As #2966, there are 3 more models have this symptom, as7326-56x, as7726-32x, and as9716-32d.
Also correct typo of naming on as7816-64x and as7716-32x.
Signed-off-by: roy_lee roy_lee@accton.com
What I did
Disabling i2c function of ir3570a which may failed i2c tranfer to others.
Close channel of mux after data transfered.
How I did it
Identify version of ir3570, if it's ir3570a, disable its alias i2c address.
Enable parameter of driver i2c_mux_pca954x to close channel on after every access.
How to verify it
Write 08 to offset 0xcf of systom eeprom and execute i2c block read.
It will return error.
plug-in several transceivers and run "show interfaces transceiver presence" and "sfputil show presence". You may see the different result. (But doing this requires updated xcvrd).
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5712-54x]
Verified with index from 1.
Add qsfp_event() for command "show interaface trancerver".
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as6712-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7726-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7712-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5812-54x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5712-54x]
Update port-config with 1-based index.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5812-54x]
Somehow the service may block, use type=simple to work-around.
Add syslog function for monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7716-32x]
Update port-config with 1-based index.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7816-64x]
Update port-config with 1-based index.
Implement sfputil change_event.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7326-56x]
Update port-config with 1-based index.
Implement sfputil change_event.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Remove debug code.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7312-54x]
Update port-config with 1-based index and default port speed.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add driver and util for peripherals of as7312-54xs, most are copied from as7312-54s.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add default port speed and index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Update i2c addr of psus.
Add system logging for monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct syntax of module_dirs.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Validate sfputil after tested.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct the index of eeprom mapping.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add new device accton_as5812_54x.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Rename 5812's config.bcm.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Change fan module to support lm-sensors.
Validate for thermal policy.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add bask reset and lpmode control of 6 QSFP ports.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Get currect duty of fan for comparing. Instead of by stored duty from previous iteration.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Roll back the mistakes to update mellanox submodules.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Rollback for misoperation on submodule platform/p4/SAI-P4-BM.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Change indexes of ports to start from 1, as them on the front panel.
Add low-power mode control of the transciever's eeprom, follows SFF-8436.
Signed-off-by: roy_lee <roy_lee@accton.com>
* catch signal SIGINT and SIGTERM to set all fans full-speed before end fan monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add fan_control monitor for as7816-64x.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Fix typo.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct typo and duty setting after verified.
Signed-off-by: roy_lee <roy_lee@accton.com>
[devices] add new accton platform minipack.
Add support for new platform, minipack.
It has
CPU: Broadwell DE – D1527
MAC: Tomahawk3(BCM56980).
PHY:Broadcom BCM81724, 4 pcs, Gearbox for PIM-16Q
BMC:AST2520
8 hot-swappable Port-Interface-Modules, each of them has 16*100G QSFP.
- What I did
Add device and platform files for minipack.
- How I did it
Add as SONiC Porting Guide.
- How to verify it
decode-syseeprom
sensors
psuutil
sfputil
thermal monitor
bcmsh on port status
(port LEDs may not working)
* [security kernel] Upgrade kernel from 4.9.110-3+deb9u2 to 4.9.110-3+deb9u6
short version: 4.9.0-7 to 4.9.0-8
See changelogs for security fixes:
https://tracker.debian.org/media/packages/l/linux/changelog-4.9.110-3deb9u6
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
* Update sonic-linux-kernel submodule after it was merged
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
