AS7816 support AT or non-AT DUT. They use different pmbus i2c bus. So use "pre_pddf_init.sh" to check this case.
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
* [AS4630-54PE] Add to support PDDF
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
* Fix LGTM alerts
* Fix LGTM alerts
* Fix LGTM alerts
* Add post_device.sh to turn off stk led
* Add to support system_health
* Correct the wait and timeout mechanism for better CPU usage
* Add event.c to support port evt change
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Add support for Accton as9726-32d platform
This pull request is based on as9716-32d, so I reference as9716-32d to create new model: as9726-32d.
This module do not need led driver to control led, FPGA can handle it.
I also implement API2.0(sonic_platform) for this model, CPLD driver, PSU driver, Fan driver to control these HW behavior.
This switch has 27 fiber ports, 4x25G, 20x10G , and 3x100G ports ports.
CPU: Intel ® Atom™ Processor C3508,1.6GHz
BMC: None
MAC: Broadcom BCM88470 (Qumran AX).
MISC: Support IEEE1588v2, hot-swappable PSU, hot-swappable fan tray.
But notice here, BCM88470 is not supported for SAI now.
So the syncd container is not running so far.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add driver and util for peripherals of as7312-54xs, most are copied from as7312-54s.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add default port speed and index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Update i2c addr of psus.
Add system logging for monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct syntax of module_dirs.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Validate sfputil after tested.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct the index of eeprom mapping.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add new device accton_as5812_54x.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Rename 5812's config.bcm.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Change fan module to support lm-sensors.
Validate for thermal policy.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add bask reset and lpmode control of 6 QSFP ports.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Get currect duty of fan for comparing. Instead of by stored duty from previous iteration.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Roll back the mistakes to update mellanox submodules.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Rollback for misoperation on submodule platform/p4/SAI-P4-BM.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Change indexes of ports to start from 1, as them on the front panel.
Add low-power mode control of the transciever's eeprom, follows SFF-8436.
Signed-off-by: roy_lee <roy_lee@accton.com>
[devices] add new accton platform minipack.
Add support for new platform, minipack.
It has
CPU: Broadwell DE – D1527
MAC: Tomahawk3(BCM56980).
PHY:Broadcom BCM81724, 4 pcs, Gearbox for PIM-16Q
BMC:AST2520
8 hot-swappable Port-Interface-Modules, each of them has 16*100G QSFP.
- What I did
Add device and platform files for minipack.
- How I did it
Add as SONiC Porting Guide.
- How to verify it
decode-syseeprom
sensors
psuutil
sfputil
thermal monitor
bcmsh on port status
(port LEDs may not working)
* Remove exsiting sonic-platform-modules-accton and apply submodule adding on this folder.
* Remove redundant commnet
* Remove folder platform/broadcom/sonic-platform-modules-accton.
* Add this dir for submodule.
