- Why I did it
To include latest fixes.
1. On CMIS modules, after low power configuration, the firmware waited for the module state to be ModuleReady instead of ModuleLowPower causing delays.
2. When connecting Spectrum devices with optical transceivers that support RXLOS, remote side port down might cause the switch firmware to get stuck and cause unexpected switch behavior.
3. On rare occasions, when working with port rates of 1GbE or 10GbE and congestion occurs, packets may get stuck in the chip and may cause switch to hang.
4. When ECMP has high amount of next-hops based on VLAN interfaces, in some rare cases, packets will get a wrong VLAN tag and will be dropped.
5. Using SN4600C with copper or optics loopback cables in NRZ speeds, link may raise in long link up times ( up to 70 seconds).
6. When connecting SN4600C to SN4600C after Fastboot in 50GbE No_FEC mode with a copper cable, the link up time may take ~20 seconds.
- How I did it
Updated SDK submodule and relevant makefiles with the required versions.
- How to verify it
Build an image and run tests from "soni-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
- Why I did it
Update SDK\FW version to 4.4.3326\2008.3326. This version contains:
New Features:
1. Add support for Fast Boot for SN3800
Bug Fixing:
1. In some cases, when the total number of allocations exceeds the resource limit, an error can occur due to incorrect resource release procedure. This issue is most likely to affect the following resources: flow counters, ACL actions, PBS, WJH filter, Tunnels, ECMP containers, MC (L2 &L3)
2. On Spectrum systems, when using Async Router API with IPV6, an error message in the log regarding failing to remove ECMP container may show up. This error is not functional and can be safely ignored.
3. On Spectrum-2 systems and above, when using warm boot, setting max_bridge_num to a value greater than 1968 will cause an error and potential crash.
4. Some Molex cables do not support speed after reboot
- How I did it
- How to verify it
Was verified by running regression tests that includes complete sonic-mgmt tests supported
Signed-off-by: Dror Prital <drorp@nvidia.com>
* [Mellanox] Update FW version to 2008.3218 (#8079)
Update FW version to 2008.3218, fixing the following issues:
- 50G/100G links that are operationally down before warm-reboot are not coming up after warm-reboot
- 50G/100G links with admin shut / no shut commands are not coming up after warm-reboot
New features and fixes in the new SDK/FW:
SN4600C | AN/LT support
SN2700 | AN/LT bugs fixes
WJH | FID_MISS support
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Fix the following issues:
Spectrum-2, Spectrum-3 | Port | Fix link issue when using 25 GbE rate between two ports while one is on Spectrum-2-based system and the other is on Spectrum-3-based system
All | warmboot | fail to upgrade from earlier SONiC versions with official SDK/FW 4.4.2306 (was on SONiC 201911)
All | What-Just-Happened | When enabling or disabling WJH under high traffic load to the host CPU, in very specific and low probability conditions, an error could occur, that may result in loss of data, channel failure or in extreme cases SW failure
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
- Why I did it
To pick up new features and fix from SDK/FW and SAI
SDK/FW new Feature:
All | Added support for multiple modules and cable types. For full list contact Nvidia networking support
Spectrum-3 | SN46000C | Added support for up to 5W on ports 49 to 64 .
SDK/FW bugs' fix:
All | fast reboot | fast boot failure from latest 201811 to 201911 and above
Spectrum | 10GbE/1GbE Transceiver (FTLX8574D3BCV) stopped working after firmware upgrade
Spectrum-2 | When device is rebooted with locked Optical Transceivers in split mode, the firmware may get stuck
Spectrum-2 | SN3700 | When connecting at 200GbE to Ixia K400, Ixia receives CRC errors
Spectrum-2 | SN3800 | On rare occasions packets loss may be experienced due to signal integrity issues
Spectrum-2 | When the port is a member of a LAG, after a warmboot and port toggle on the peer-side, the port remains down
Spectrum-3 | SN4700 | While using Optic cable in Split 4x1 mode in PAM4, when two first ports are toggled, the other 2 ports go down
Spectrum-3 | SN4700 | When working in 400GbE, deleting the headroom configuration (changing buffer size to zero) on the fly may cause continual packet drops
SAI
All | Counters | Update tunnel decap counter to capture VNI miss
- How I did it
Update the related version number in the make files and update the submodule pointer accordingly.
- How to verify it
Run regression test and everything works good.
To have the following fixes:
* All | Port status remains down after warm boot and flapping the port on peer side
* All | LAG HASH | IPv6 SRC_IP is not accounted in LAG hashing [
* All | ASIC driver | Kernel crash observed when driver reload is initiated before it fully loaded
* Spectrum-3 | Buffer | In lossless configuration, headroom is been evicted only when the shared buffers is free
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
Bugs fixes:
All | Kernel | During system reload when CPU is loaded with heavy traffic, a Kernel Panic may occur.
All | Modules, Port split | FW stuck when device rebooted with locked Optical Transceivers in split mode
Spectrum-3 | PFC | On Spectrum-3 systems, slow reaction time to Rx pause packets on 40GbE ports may lead to buffer overflow on servers.
Spectrum-3 | SN4700, Port Split | On rare occasion SN4700, conducting 100G split (4x25G) in NRZ when splitter port 1 or 2 are down, ports 3 and 4 will also go down.
Enahncments:
All | Kernel | new notification on ISSU start, so other kernel drivers can disable any interface to ASIC
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Update SDK 4.4.1956 and FW *.2008.1956
Bugs fixes:
1. Link | Clear operational speed when link is not active
2. Spectrum-2, SN3800 | On rare occasion, link flapping due to bad BER causes traffic loss
3. Spectrum-3 | On rare occasion, link flapping due to bad BER causes traffic loss as a result of new PAM4 link maintenance flow on Spectrum-3 devices
4. Shared Buffers | On rare occasion, modifying shared buffers on a system with split port while traffic is running may cause the firmware to get stuck
5. Spectrum-3, SN4700 | Fence may fail while running 400GbE 8x port when modifying mirror session configurations under traffic
- SN3800 vs Cisco9236 - no link copper or optics - start sending IDLE before PHY_UP for specific OPNs
Signed-off-by: Nazarii Hnydyn <nazariig@nvidia.com>
SAI:
Fix ECMP max groups logic
add set issu log level for spc2/spc3, as now issu is supported
set vlan max swid = 0 on sdk init, as only single swid is needed, for efficient resource usage
Fix traffic lost during FFB related to buffer config + optimize buffer config timing for FB
Add ACL fields BTH, IP flags
Add ACL infrastructure of different fields per ASIC type
Add port stat ether rx/tx oversize pkts
SDK/FW:
Added support for Finisar 100GbE SWDM Transceiver FTLC9152RGPL.
Spectrum-2 Added support for 10G BaseT modules
Added link LED support for SN4600C.
Counters | In SDK debug dump, the incorrect counter type appears for vtraps.
WJH | Without any traffic or events on the idle system, the CPU load is constantly above 4%
WJH | WJH filter currently cannot filter by PORT for buffer drop reason.
Spectrum | ACL, Unbind, Lazy Delete | Running Lazy Delete together with auto_unbind may cause rate condition errors. To work work with Lazy Delete use new INIT parameter "acl_manual_unbind" so that ACLs will notbe removed automatically when binding point is deleted.
Spectrum | ISSU | In ISSU mode, when querying for the number of configurable buffers, using the API sx_api_cos_port_buff_type_get with the count parameter as 0, the API returns the number for NORMAL mode instead.
Spectrum-2 | BER | BER monitor counts raw errors instead of effective errors
Spectrum-2 | BER | Connecting to ConnectX-5 adapter card with copper splitter cable MCP7H50-V001R30 in 1
Spectrum-2 | Cables | Link flaps in 200GbE with AOM Optic cable MMA1T00-VS
Spectrum-3 | Speeds, Link | When moving from a 400GbE link to a 1GbE link, packets may drop for 1msec right after link up
Spectrum-3 | Cables, Speeds | Using 400GbE with 3rd party systems is not supported
Spectrum-3 | LAG | After a while, LAG members become out of sync with one another
Spectrum-3 | VLAN, Ports | Packets with VLAN headers are sent to
Update SAI/SDK/FW and MSN4700 device files to support 8 lanes 400G
Update SAI to 1.16.3
Update SDK to 4.4.0914
Update FW to *.2007.1112
Update MSN4700 device files to support 8 lanes 400G
update FW to xx_2000_3298
update SAI to 1.16.0
update Spectrum-1 and Spectrum-2 buffer pool size according to the new SDK default config change.
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t1.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t1.j2
modified: fw.mk
modified: mlnx-sai.mk
modified: mlnx-sai/SAI-Implementation
modified: sdk-src/sx-kernel/Switch-SDK-drivers
modified: sdk.mk
signed-off by kebol@mellanox.com
Adjust the SDK makefiles so that it reflects the dependencies among libraries in SDK 4.3.2104.
This is a supplement of PR [Mellanox]Update SDK(4.3.2104), SAI-Implementation(1.15) and firmware 2162. It doesn't impact the sonic-mellanox.bin image but makes the future SDK-integration easier.
Integrating official Mellanox SDK/FW release as a pre condition for getting new Mellanox SAI release with hash changes (inner field) and 3k VXLAN scale. As well as bug fix for Spectrum LP mode and Spectrum 2 PFC WD
Signed-off-by: Mykola Faryma <mykolaf@mellanox.com>
* [submodule] update sonic-linux-kernel
* update linux kernel version
* Fix many version strings
* update mellanox components (built with new kernel)
* [mlnx] add make files for SDK WJH libs
* Update arista driver submodule (#8)
Make the debian packaging point to a newer kernel version.
* [build]: put stretch debian packages under target/debs/stretch/
* in stretch build phase, all debian packages built in that stage are placed under target/debs/stretch directory.
* for python-based debian packages, since they are really the same for jessie and stretch, they are placed under target/python-debs directory.
Signed-off-by: Guohan Lu <gulv@microsoft.com>
