* Add intel_iommu=off to installer.conf
* This solve flooding DMAR err msg: "handling fault status reg 2"
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* remove customized at24 driver
* Use kernel 5.10.46 upstream at24 driver directly. The ADDR16 issue on
old driver has gone.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* pin I2C-0/I2C-1 bus order
* otherwise, sometimes I2C-0/I2C-1 will be assigned to the undesired one.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* fix i2c bus num for fan driver
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
* backward compatible with R0A/R0B HW
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
Enable pca954x idle_disconnect to avoid possible I2C device address conflict.
How I did it
Change pca954x device_attr idle_state to -2 (MUX_IDLE_DISCONNECT).
How to verify it
Cat pca954x device_attr idle_state and confirm the value is -2.
Signed-off-by: Sean Wu <sean_wu@edge-core.com>
CPLD offset in led drv is incorrect.
#### How to verify it
echo 1 > brightness, show green on in DIAG led
echo 3 > brightness, show red on in DIAG led
echo 4 > brightness, show blue on in DIAG led
echo 5 > brightness, show green blinking in DIAG led
Signed-off-by: Jostar Yang <jostar_yang@accton.com.tw>
Add needed code to pddf_custom_psu.c to deal with multi PSU and get SN.
How to verify it
Plugin new PSU (3Y) and test,
```
root@sonic:/sys/bus/i2c/drivers/psu/9-0050# cat psu_serial_num
S0A000X601919000013
root@sonic:/sys/bus/i2c/drivers/psu/9-0050# cat psu_model_name
YESM1300AM
root@sonic:/home/admin# pddf_psuutil mfrinfo
PSU Status Manufacturer ID Model Serial Fan Airflow Direction
PSU1 NOT OK 3Y POWER YESM1300AM S0A000X601919000007 exhaust
PSU2 OK 3Y POWER YESM1300AM S0A000X601919000013 exhaust
```
Co-authored-by: Jostar Yang <jostar_yang@accton.com.tw>
Add support for Accton as9726-32d platform
This pull request is based on as9716-32d, so I reference as9716-32d to create new model: as9726-32d.
This module do not need led driver to control led, FPGA can handle it.
I also implement API2.0(sonic_platform) for this model, CPLD driver, PSU driver, Fan driver to control these HW behavior.
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
bug fix: #5914
Validated for tx_disable function of SFP+ on AS7312-54X, AS5812-54X, AS5712-54x, and AS5812-54x.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
Fix 259 alerts reported by the LGTM tool:
- 245 for Unused import
- 7 for Testing equality to None
- 5 for Duplicate key in dict literal
- 1 for Module is imported more than once
- 1 for Unused local variable
Original converting from register is wrong, it makes the fan speed much higher than it is. Change the way fan speed is calculated from CPLD.
Signed-off-by: roy_lee <roy_lee@accton.com>
HW set qsfp port to reset at default. so need SW to set to normal when boot.
1. Modify cpld driver to invert reset offset value
2. Set to normal when boot.
**- Why I did it**
The tx_disable function isn't work for the accton_ax5835-54x device.
**- How I did it**
Fix the incorrect path of the sfp node path inside the util file.
**- How to verify it**
Test with
"sudo accton_as5835_54x_util.py show"
"sudo accton_as5835_54x_util.py set sfp"
There should see correct value for module_present and module_tx_disable. And should able to set it.
Signed-off-by: kuanyu_chen <kuanyu_chen@edge-core.com>
3y Power YPEB-1200am PSU doens't support read fan_dir from pmbus register
Check with vendor this PUS type only support F2B fan direction. So add to show "F2B"
when red psu_fan_dir sysfs.
1. undefine led_classdev_register as it is defined in leds.h
2. header file location change
a. linux/i2c/pmbus.h -> linux/pmbus.h
b. linux/i2c-mux-gpio.h -> linux/platform_data/i2c-mux-gpio.h
c. linux/i2c/pca954x.h -> linux/platform_data/pca954x.h
Due to linux create hwmonN node number, N isn't fixed. So modify to use "" to let thermal.py can correct sysfs. For example, use /sys/bus/i2c/devices/55-0048/hwmon/hwmon/temp1_input to instead of /sys/bus/i2c/devices/55-0048/hwmon/hwmon4/temp1_input
AS7326-56X and AS7726-56X use the same design so both devices have the same problem.
The detailed description below takes AS7326-56X as the example to explain.
Original implementation:
- In platform/broadcom/sonic-platform-modules-accton/as7326-56x/service/as7326-platform-handle_mac.service,
it executes the script file "accton_handle_idt.sh".
- In "accton_handle_idt.sh", it modifies the content of the script file "/etc/init.d/opennsl-modules"
to insert the lines to execute "idt_init.sh" before the command to load broadcom linux kernel module "linux-kernel-bde.ko".
- The script "idt_init.sh" cannot be executed at the first boot of SONiC after installing SONiC under ONIE. This is the reason why all of the ports does not work.
New implementation:
- Let "as7326-platform-handle_mac.service" execute "idt_init.sh".
- Change the content of "as7326-platform-handle_mac.service" to define the service type as "oneshot". Add the settings to ensure "as7326-platform-handle_mac.service" is executed before "opennsl-modules.service".
By setting the service type as "oneshot", it is guaranteed that "opennsl-modules.services" is started only when the forked process to execute the script file "idt_init.sh" is terminated
Signed-off-by: charlie_chen <charlie_chen@edge-core.com>
