Why I did it
Cherry pick changes in #9197 to 202012 branch
Add bgpcfgd support to advertise routes.
How I did it
Make bgpcfgd subscribe to the ADVERTISE_NETWORK table in STATE_DB and configure route advertisement accordingly.
How to verify it
Added unit tests in bgpcfgd and verify on KVM about route advertisement.
Why I did it
Eliminate benign firsttime boot error reported when running on platforms that do not support kdump.
How I did it
Change rc.local to check for presence of the file /etc/default/kdump-tools before referencing it.
How to verify it
Install a new image on an armhf or arm64 platform and check for a failed reference to /etc/default/kdump-tools on firsttime boot.
- Consolidate the two [Service] sections by moving the ExecStartPre line for mark_dhcp_packet.py to the first section and removing the second.
- Make the mark_dhcp_packet.py file executable
- Also clean up mark_dhcp_packet.py
- Remove unused imports
- Fix spacing and line lengths to conform to PEP8
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
- Why I did it
This is to update the common sonic-buildimage infra for reclaiming buffer.
- How I did it
Render zero_profiles.j2 to zero_profiles.json for vendors that support reclaiming buffer
The zero profiles will be referenced in PR [Reclaim buffer] Reclaim unused buffers by applying zero buffer profiles #8768 on Mellanox platforms and there will be test cases to verify the behavior there.
Rendering is done here for passing azure pipeline.
Load zero_profiles.json when the dynamic buffer manager starts
Generate inactive port list to reclaim buffer
Signed-off-by: Stephen Sun <stephens@nvidia.com>
1. CS00012211718 [4.3] Pfcwd getting continuously triggered/restored when pause frames are sent continuously to both queues of a port (TD2/Th/Th2/TD3) MSFT Default
Preliminary tests look fine. BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on 7050CX3 (TD3) T0 DUT and all passed:
```
fib/test_fib.py
vxlan/test_vxlan_decap.py
fdb/test_fdb.py
decap/test_decap.py
ipfwd/test_dip_sip.py
ipfwd/test_dir_bcast.py
acl/test_acl.py
vlan/test_vlan.py
platform_tests/test_reboot.py
```
- add a new service "mark_dhcp_packet" to mux container
- apply packet marks on a per-interface basis in ebtables
- write packet marks to "DHCP_PACKET_MARK" table in state_db
This is to pick up BRCM SAI 4.3.5.1-7 fixes which contains the following fixes:
1. CS00012209390: SONIC-50037, Used SAI_SWITCH_ATTR_QOS_DSCP_TO_TC_MAP as a default decap map for IPinIP tunnels.
2. CS00012212995: SONIC-50948 SAI_API_QUEUE:_brcm_sai_cosq_stat_get:1353 egress Min limit get failed with error Invalid parameter
3. SONIC-51583: Fixed acl group member creation failure with priority of -1
4. CS00012215744:SONIC-51395 [TH, TH2] WB 3.5 to 4.3 fails at APPLY_VIEW while setting SAI_PORT_ATTR_EGRESS_ACL
5. SONIC-51638: SDK-249337 ERROR: AddressSanitizer: heap-buffer-overflow in _tlv_print_array
Preliminary tests look fine. BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on 7050CX3 (TD3) T0 DUT and all passed:
```
fib/test_fib.py
vxlan/test_vxlan_decap.py
fdb/test_fdb.py
decap/test_decap.py
ipfwd/test_dip_sip.py
ipfwd/test_dir_bcast.py
acl/test_acl.py
vlan/test_vlan.py
platform_tests/test_reboot.py
```
[write_standby]: Ignore non-auto interfaces
* In the event that `write_standby.py` is used to automatically switchover interfaces when linkmgrd or bgp crashes, ignore any interfaces that are not configured to auto-switch
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
[mux] Update Service Install With SONiC Target
Recent PR grouped all SONiC service into sonic.taget. The install section
of mux.service was not update and this causes delays when using config
reload as the service failed state is not being reset.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
[mux] Start Mux on Only Dual-ToR Platform
mux docker depends on the presence of mux cable hardware and is
supposed to run only Gemini ToRs. This PR change the mux feature
config in order to enable mux docker based on device configuration.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Linkmgrd monitors link status, mux status, and link state. Has
the link becomes unhealthy, linkmgrd will trigger mux switchover
on a standby ToR ensuring uninterrupted service to servers/blades.
This PR is initial implementation of linkmgrd.
Also, docker-mux container hold packages related to maintaining and managing
mux cable. It currently runs linkmgrd binary that monitor and switches
the mux if needed.
This PR also introduces mux-container and starts linkmgrd as startup when
build is configured with INCLUDE_MUX=y
Edit: linkmgrd PR will follow.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Related work items: #2315, #3146150
This is to pick up BRCM SAI 4.3.5.1-6 fixes which contains the following fixes:
1. CS00012213351 SONIC-50679: [TH, TH2] Warm-reboot from 3.5 to 4.3 fails due to null objects discovered
2. CS00012182162: SONIC-49805 TD3 MMU config profile optimization changes
3. CS00012210826:SONIC-50205/760c60fc: Should read MMU_INTFI_MMU_PORT_TO_MMU_QUEUES_FC_BKP for TH3
Preliminary tests looks fine. BGP neighbors were all up with proper routes programmed
interfaces are all up
Manually ran the following test cases on 7050CX3 (TD3) T0 DUT and all passed:
```
fib/test_fib.py
vxlan/test_vxlan_decap.py
fdb/test_fdb.py
decap/test_decap.py
ipfwd/test_dip_sip.py
ipfwd/test_dir_bcast.py
acl/test_acl.py
vlan/test_vlan.py
platform_tests/test_reboot.py
```
copp-config service needs to be started after sonic.target so that it could
render the copp-config with the latest information.
It also needs to be restarted when config reload or load_minigraph is invoked.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
As a part of warmboot, redis database is dumped:
c97fe546e5/scripts/fast-reboot (L269)
However, this dump file is deleted, after it is loaded back into db post reboot.
The DB dump can be useful for debugging purpose, hence taking a backup of it can be useful.
Instead of deleting the dump, rename and keep the dump.
Added logrotate file for wtmp and btmp to override default conf and set size cap as 100K as done in
PR: #865. For buster this is control by separate file wtmp and btmp.
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
