I2c burst read may failed due to misoperation of ir3570a(A DC-to-DC converter IC).
As #2966, there are 3 more models have this symptom, as7326-56x, as7726-32x, and as9716-32d.
Also correct typo of naming on as7816-64x and as7716-32x.
Signed-off-by: roy_lee roy_lee@accton.com
What I did
Disabling i2c function of ir3570a which may failed i2c tranfer to others.
Close channel of mux after data transfered.
How I did it
Identify version of ir3570, if it's ir3570a, disable its alias i2c address.
Enable parameter of driver i2c_mux_pca954x to close channel on after every access.
How to verify it
Write 08 to offset 0xcf of systom eeprom and execute i2c block read.
It will return error.
plug-in several transceivers and run "show interfaces transceiver presence" and "sfputil show presence". You may see the different result. (But doing this requires updated xcvrd).
Signed-off-by: roy_lee <roy_lee@accton.com>
* src/sonic-utilities ee56d54...cb0e745 (11):
> sonic_utilities: Support for DOM Threshold values for EEPROM dump
(#545)
> [portstat] Fix portstat show RX_UTIL over 100% for 100G (#563)
> sonic_installer: fix read-only filesystem support for firmware
update (#565)
> Revert "show acl table command output should show binding column
correctly even with single port (#447)" (#589)
> show acl table command output should show binding column correctly
even with single port (#447)
> [config] Do no stop or restart dependent services (#582)
> sfpshow: prevent 'show int trans eeprom --dom' from crashing (#567)
> [warm-reboot] add docker upgrade --warm option and roll back support
(#559)
> [ecnconfig] Validate input WRED parameters (#579)
> [sonic-utilities] Add fstrim to reboot (#535)
> Fixing the expected neighbor command due to change in output format
under sonic-buildimage/pull/3036 (#584)
- What I did
Move the enabling of Systemd services from sonic_debian_extension to a new systemd generator
- How I did it
Create a new systemd generator to manually create symlinks to enable systemd services
Add rules/Makefile to build generator
Add services to be enabled to /etc/sonic/generated_services.conf to be read by the generator at boot time
Signed-off-by: Lawrence Lee <t-lale@microsoft.com>
* [Mellanox]refractor the sfp event change notification logic for new platform api
remove the standalong daemon which is in charge of polling sfp change event through sdk interface
and move the polling stuff to the event in the chassis daemon.
* rephase some comment
* fix typo in sfp_event.sfp_event.initialize
ARM Architecture support in SONIC
make configure platform=[ASIC_VENDOR_ARCH] PLATFORM_ARCH=[ARM_ARCH]
SONIC_ARCH: default amd64
armhf - arm32bit
arm64 - arm64bit
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
This commit adds support for New feature management VRF using L3mdev. Added
commands to enable/disable management VRF. Config vrf add mgmt will enable
management VRF, enslave the eth0 device to the master device mgmt and restart
interfaces-configs in mgmt-vrf context.
management interface (eth0) can be configured using config interface eth0 ip
add command and removed using config interface eth0 ip remove command.
Requirement and design are covered in mgmt vrf design document. Currently show
command displays linux command output; will update show command display in next
PR after concluding what would be the output for the show commands. Added
metric for default routes in dhcp and static, any changes for metric will be
addressed subsequently after discussing.
Signed-off-by: Harish Venkatraman <harish_venkatraman@dell.com>
Added Reboot Reason for S6000 in platform 2.0
Fixed issue in process-reboot-cause
Added package uninstall code in platform de-init code for z9100, s6100
- How I did it
-> Added support for S6000 Reboot Reason
-> Added platform.py for all platforms
-> Verified show reboot-cause command with the code changes. Added UT logs with show reboot-cause
-> Modified process-reboot-cause service to start after pmon.service. In S6000, we have to wait for nvram to be loaded.
-> If reboot-cause service starts before pmon.service, show reboot-cause is showing incorrect reason.
-> Bug fix in process-reboot-cause file
- import sonic_platform
+ import sonic_platform.platform
* [as5712-54x]
Verified with index from 1.
Add qsfp_event() for command "show interaface trancerver".
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as6712-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7726-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7712-32x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5812-54x]
Add default port speed.
Verified with index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5712-54x]
Update port-config with 1-based index.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as5812-54x]
Somehow the service may block, use type=simple to work-around.
Add syslog function for monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7716-32x]
Update port-config with 1-based index.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7816-64x]
Update port-config with 1-based index.
Implement sfputil change_event.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7326-56x]
Update port-config with 1-based index.
Implement sfputil change_event.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Remove debug code.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [as7312-54x]
Update port-config with 1-based index and default port speed.
Signed-off-by: roy_lee <roy_lee@accton.com>
* [warm reboot] save configuration after warm reboot
After warm reboot, save a copy of in memory database to config_db.json,
upgrade procedure might have removed config_db.json to force new image
to reload minigraph. However, reload minigraph is skipped during warm
reboot. Missing config_db.json would cause device to fault in next
non-upgrading cold/fast reboot.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
* Update finalize-warmboot.sh
The following commit addresses the graceful unmounting of file
system and graceful shutdown of dockers before calling a
cold reboot which will cause a power cycle of SSD. This ensures
orderly shutdown and no corruption of files systems because
of the power cycle to SSD.
This commit will use the existing systemd-reboot service scripts
and override the configuration to do cold reboot for S6100 and
Z9100.
Unit tested the fix and graceful shutdown of file system and
dockers are done with cold reboot.
Signed-off-by: Harish Venkatraman <harish_venkatraman@dell.com>
* support new platform api, thermal and psu part
for psu, all APIs are supported.
for thermal, we support
get_temperature,
get_high_threshold
for the thermal sensors of cpu core, cpu pack, psu and sfp module
and get_temperature for the ambient thermal sensors around the asic, port, fan, comex and board.
* 1. address review comments
2. improve the handling of PSU inserting/removal
3. tolerance diverse psu thermal sensor file name conventions
* 1. adjust thermal code according to the latest version of hw-management
2. check power_good_status rather than whether file existing ahead of reading voltage, current and power of PSU
* Upgrade ifupdown2 to version 1.2.8
Required by ZTP to support ZTP over IPv6 transport
Signed-off-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com>
swss:
[vxlanorch]: Allow ipv6 src ip for Vxlan tunnel creation (#896)
[aclorch]: Allow DTEL drop actions in DTEL flow watchlist (#915)
Fix typo in orchagent_restart_check from fasle to false. (#923)
[sonic-swss]: Fix for FPM accept call failure in ARM arch (#925)
Add retryCount option for orchagent_restart_check program. (#833)
[vlan] Add pytest cases to validate nonexistent vlan behavior. (#874)
[intfsorch] Wait for interface prior to prefix (#796)
Set timer only when interval changes. Not in each firing of the timer. (#945)
[test]: Fix set interface in configuration database (#956)
[copporch]: Fix polymorphic type error (#946)
[AclOrch]: Fix the acl mirror counter doubled by inactive mirror and active again (#952)
[MirrorOrch]: Init the next hop ip with 0 instead of default constructor (#953)
[portsorch]: Add reference count of port (#962)
[mock_test]: Move mock tests into a separate folder to separate them from vs tests (#950)
remove crm acl_counters when acl_table removed (#918)
[aclorch]: Fix matching MIRROR_DSCP throws unnecessary errors (#966)
[policerorch]: Fix return code comparison error (#968)
[gitignore]: Add swss-dbg related files (#967)
[vxlanmgrd]: Fix for vxlanmgrd cannot correctly work after config reload (#934)
[vxlanorch]: Add extra info into NOTICE logs (#891)
[test]: Add a neighbor entry with BCAST MAC and verify its ignored (#955)
[copporch]: Fix copporch in DEL command (#972)
[orchagent]: Fix crash during orchagent process exit (#974)
[vnetorch]: Fix VNET orchagents order for warm-reboot flow (#958)
[test]: Skip unstable test test_vnet_orch_1 (#976)
[intfsorch]: Fix rif flex counter removal error (#975)
Update tests README.md file
[aclorch]: Change CFG_ACL_TABLE_NAME to CFG_ACL_TABLE_TABLE_NAME (#978)
[test]: Skip test_watermark.py::TestWatermark::test_lua_plugins (#981)
[teamsyncd]: Add information for LAG membership changes (#982)
common:
Add an assert to logger, which will log a message and abort. (#286)
[test]: Add IpAddress::isZero() unit test (#289)
do not abort when read timerfd return 0 and errno = 0 (#291)
Add BGP_STATE_TABLE in stateDB (#273)
[IpAddress]: add mcast scope on address and isFullMask method on prefix (#285)
Add ignore Wshadow pragma to json.hpp (#292)
[executor]: Fix Executor does not get correct priority saved in m_selectable (#290)
[schema]: Remove duplicate STATE_MIRROR_SESSION_TABLE_NAME (#294)
timerfd:read failure - Record in logs as error. (#295)
[schema]: Change CFG_ACL_TABLE_NAME to CFG_ACL_TABLE_TABLE_NAME (#296)
[schema]: Add PASS_THROUGH_ROUTE_TABLE to config and application db (#297)
sairedis:
ARM32 bit fixes, for 64bit printf format specifier (#468)
Reduce the timeout (GET_RESPONSE_TIMEOUT) from 6 minutes to 1 minute. (#472)
Fixed config_syncd_barefoot function (#474)
[syncd_init_common.sh] fix fast reboot backwards compatibility (#480)
Add default bridge id for bridge port id of type PORT in virtual switch (#473)
Fix a bug in parsing kernel argument of fast-reboot (#482)
Add TimerWatchdog for monitoring long execution apis (#469)
Add specific comparison logic for tunnel map (#475)
[vslib] add ACL action capabilities support (#481)
Per buffer pool watermark polling mode (#485)
Add specific comparison logic for ACL counter (#484)
Process flex counters requests in separate thread (#483)
Make sairedis/syncd synchronous (#476)
Fixed conditional operator. (#487)
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
* [devices]: Add a new supported device DellEMC s5232f
* Switch Vendor: DellEMC
* Switch SKU: s5232F
* ASIC Vendor: Broadcom
* Swich ASIC: Trident3
* Port Configuration: 32x100G
* SONiC Image: sonic-broadcom.bin
* LED support for s5232f
* Changes Include ipmitool implementation for platform_sensors script is inclued in pmon startup
* Added 100G,25G,10G configruation ( 100G is default).
* s5232[device] PSU detecttion and default led state support
* Add driver and util for peripherals of as7312-54xs, most are copied from as7312-54s.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Add default port speed and index from 1.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Update i2c addr of psus.
Add system logging for monitor.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct syntax of module_dirs.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Validate sfputil after tested.
Signed-off-by: roy_lee <roy_lee@accton.com>
* Correct the index of eeprom mapping.
Signed-off-by: roy_lee <roy_lee@accton.com>
Without quote, the command will ignore the version and
regard the ">" as a file redirection symbol and redirect
all the output to a file named the version range.
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
* Subscribe to both ConfigDB and AppDB
to get notifications to apply LLDP port config
* the operstate file is not consistent
Removing this since it is not serving any purpose
* Remove check for PortInitDone and PortConfigDone
This is not prteset in Config DB
* Remove checking State DB for port creation
* Check for key to be present before fetching it
* Addressing review comments
Integrating official Mellanox SDK/FW release as a pre condition for getting new Mellanox SAI release with hash changes (inner field) and 3k VXLAN scale. As well as bug fix for Spectrum LP mode and Spectrum 2 PFC WD
Signed-off-by: Mykola Faryma <mykolaf@mellanox.com>
