What I did:
Updated Jinja Template to enable BGP Graceful Restart based on device role. By default it will be enable only if the device role type is TorRouter.
Why I did:-
By default FRR is configured in Graceful Helper mode. Graceful Restart is needed on T0/TorRouter only since the device can go for warm-reboot. For T1/LeafRouter it need to be in Helper mode only
resolves#8979 and #9055
How I did it
Remove the file static.conf.j2,which adds the default route on eth0 from frr docker
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
In the multi asic platforms all the ASIC are advertising the same IPv6 /64 network from Loopback4096.
Therefore, the IPv6 loopback address of backend asic is not learnt on the frontend asic.
Change this to advertise the Loopback4096 address as /128
Why I did it
It was observed that on a multi-asic DUT bootup, the BGP internal sessions between ASIC's was taking more time to get ESTABLISHED than external BGP sessions. The internal sessions was coming up almost exactly 120 secs later.
In multi-asic platform the bgp dockers ( which is per ASIC ) on switch start are bring brought up around the same time and they try to make the bgp sessions with neighbors (in peer ASIC's) which may be not be completely up. This results in BGP connect fail and the retry happens after 120sec which is the default Connect Retry Timer
How I did it
Add the command to set the bgp neighboring session retry timer to 10sec for internal bgp neighbors.
1. Made the command next-hop-self force only applicable on back-end asic bgp. This is done so that BGPL iBGP session running on backend can send e-BGP learn nexthop. Back end asic FRR is able to recursively resolve the eBGP nexthop in its routing table since it knows about all the connected routes advertise from front end asic.
2. Made all front-end asic bgp use global loopback ip (Loopback0) as router id and back end asic bgp use Loopbacl4096 as ruter-id and originator id for Route-Reflector. This is done so that routes learnt by external peer do not see Loopback4096 as router id in show ip bgp <route-prerfix> output.
3. To handle above change need to pass Loopback4096 from BGP manager for jinja2 template generation. This was missing and this change/fix is needed for this also https://github.com/Azure/sonic-buildimage/blob/master/dockers/docker-fpm-frr/frr/bgpd/templates/dynamic/instance.conf.j2#L27
4. Enhancement to add mult_asic specific bgpd template generation unit test cases.
Enable BBR config allowas-in 1 for internal peers
Why I did:
To advertise BBR routes learnt via e-BGP peer in one asic/namespace to another iBGP asic/namespace via Route Reflector.
* Use 20 and 30 route-map entries instead of 2 and 3 for TSA
* Added support for dynamic "Allow list" default action.
Co-authored-by: Pavel Shirshov <pavel.contrib@gmail.com>
Calls to sonic-cfggen is CPU expensive. This PR reduces calls to
sonic-cfggen to two calls during startup when starting frr service.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Fixed TSA bugs:
1. TSA didn't advertise Loopback ipv6 address
2. TSA and TSB changed BGP dynamic and BGP monitors sessions
**- How to verify it**
Build an image and run on your DUT.
```
admin@str-s6100-acs-1:~$ TSA
System Mode: Normal -> Maintenance
admin@str-s6100-acs-1:~$ vtysh -c 'show bgp ipv4 neighbors 10.0.0.1 advertised-routes'
BGP table version is 6, local router ID is 10.1.0.32, vrf id 0
Default local pref 100, local AS 64601
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 10.1.0.32/32 0.0.0.0 0 32768 i
Total number of prefixes 1
admin@str-s6100-acs-1:~$ vtysh -c 'show bgp ipv6 neighbors fc00::a advertised-routes'
BGP table version is 6, local router ID is 10.1.0.32, vrf id 0
Default local pref 100, local AS 64601
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> fc00:1::/64 :: 0 32768 i
Total number of prefixes 1
admin@str-s6100-acs-1:~$ TSB
System Mode: Maintenance -> Normal
```
Co-authored-by: Pavel Shirshov <pavel.contrib@gmail.com>
- Why I did it
Update the routine is_bgp_session_internal() by checking the BGP_INTERNAL_NEIGHBOR table.
Additionally to address the review comment #5520 (comment)
Add timer settings as will in the internal session templates and keep it minimal as these sessions which will always be up.
Updates to the internal tests data + add all of it to template tests.
- How I did it
Updated the APIs and the template files.
- How to verify it
Verified the internal BGP sessions are displayed correctly with show commands with this API is_bgp_session_internal()
* Initial commit for BGP internal neighbor table support.
> Add new template named "internal" for the internal BGP sessions
> Add a new table in database "BGP_INTERNAL_NEIGHBOR"
> The internal BGP sessions will be stored in this new table "BGP_INTERNAL_NEIGHBOR"
* Changes in template generation tests with the introduction of internal neighbor template files.
**- Why I did it**
To introduce dynamic support of BBR functionality into bgpcfgd.
BBR is adding `neighbor PEER_GROUP allowas-in 1' for all BGP peer-groups which points to T0
Now we can add and remove this configuration based on CONFIG_DB entry
**- How I did it**
I introduced a new CONFIG_DB entry:
- table name: "BGP_BBR"
- key value: "all". Currently only "all" is supported, which means that all peer-groups which points to T0s will be updated
- data value: a dictionary: {"status": "status_value"}, where status_value could be either "enabled" or "disabled"
Initially, when bgpcfgd starts, it reads initial BBR status values from the [constants.yml](https://github.com/Azure/sonic-buildimage/pull/5626/files#diff-e6f2fe13a6c276dc2f3b27a5bef79886f9c103194be4fcb28ce57375edf2c23cR34). Then you can control BBR status by changing "BGP_BBR" table in the CONFIG_DB (see examples below).
bgpcfgd knows what peer-groups to change fron [constants.yml](https://github.com/Azure/sonic-buildimage/pull/5626/files#diff-e6f2fe13a6c276dc2f3b27a5bef79886f9c103194be4fcb28ce57375edf2c23cR39). The dictionary contains peer-group names as keys, and a list of address-families as values. So when bgpcfgd got a request to change the BBR state, it changes the state only for peer-groups listed in the constants.yml dictionary (and only for address families from the peer-group value).
**- How to verify it**
Initially, when we start SONiC FRR has BBR enabled for PEER_V4 and PEER_V6:
```
admin@str-s6100-acs-1:~$ vtysh -c 'show run' | egrep 'PEER_V.? allowas'
neighbor PEER_V4 allowas-in 1
neighbor PEER_V6 allowas-in 1
```
Then we apply following configuration to the db:
```
admin@str-s6100-acs-1:~$ cat disable.json
{
"BGP_BBR": {
"all": {
"status": "disabled"
}
}
}
admin@str-s6100-acs-1:~$ sonic-cfggen -j disable.json -w
```
The log output are:
```
Oct 14 18:40:22.450322 str-s6100-acs-1 DEBUG bgp#bgpcfgd: Received message : '('all', 'SET', (('status', 'disabled'),))'
Oct 14 18:40:22.450620 str-s6100-acs-1 DEBUG bgp#bgpcfgd: execute command '['vtysh', '-f', '/tmp/tmpmWTiuq']'.
Oct 14 18:40:22.681084 str-s6100-acs-1 DEBUG bgp#bgpcfgd: execute command '['vtysh', '-c', 'clear bgp peer-group PEER_V4 soft in']'.
Oct 14 18:40:22.904626 str-s6100-acs-1 DEBUG bgp#bgpcfgd: execute command '['vtysh', '-c', 'clear bgp peer-group PEER_V6 soft in']'.
```
Check FRR configuraiton and see that no allowas parameters are there:
```
admin@str-s6100-acs-1:~$ vtysh -c 'show run' | egrep 'PEER_V.? allowas'
admin@str-s6100-acs-1:~$
```
Then we apply enabling configuration back:
```
admin@str-s6100-acs-1:~$ cat enable.json
{
"BGP_BBR": {
"all": {
"status": "enabled"
}
}
}
admin@str-s6100-acs-1:~$ sonic-cfggen -j enable.json -w
```
The log output:
```
Oct 14 18:40:41.074720 str-s6100-acs-1 DEBUG bgp#bgpcfgd: Received message : '('all', 'SET', (('status', 'enabled'),))'
Oct 14 18:40:41.074720 str-s6100-acs-1 DEBUG bgp#bgpcfgd: execute command '['vtysh', '-f', '/tmp/tmpDD6SKv']'.
Oct 14 18:40:41.587257 str-s6100-acs-1 DEBUG bgp#bgpcfgd: execute command '['vtysh', '-c', 'clear bgp peer-group PEER_V4 soft in']'.
Oct 14 18:40:42.042967 str-s6100-acs-1 DEBUG bgp#bgpcfgd: execute command '['vtysh', '-c', 'clear bgp peer-group PEER_V6 soft in']'.
```
Check FRR configuraiton and see that the BBR configuration is back:
```
admin@str-s6100-acs-1:~$ vtysh -c 'show run' | egrep 'PEER_V.? allowas'
neighbor PEER_V4 allowas-in 1
neighbor PEER_V6 allowas-in 1
```
*** The test coverage ***
Below is the test coverage
```
---------- coverage: platform linux2, python 2.7.12-final-0 ----------
Name Stmts Miss Cover
----------------------------------------------------
bgpcfgd/__init__.py 0 0 100%
bgpcfgd/__main__.py 3 3 0%
bgpcfgd/config.py 78 41 47%
bgpcfgd/directory.py 63 34 46%
bgpcfgd/log.py 15 3 80%
bgpcfgd/main.py 51 51 0%
bgpcfgd/manager.py 41 23 44%
bgpcfgd/managers_allow_list.py 385 21 95%
bgpcfgd/managers_bbr.py 76 0 100%
bgpcfgd/managers_bgp.py 193 193 0%
bgpcfgd/managers_db.py 9 9 0%
bgpcfgd/managers_intf.py 33 33 0%
bgpcfgd/managers_setsrc.py 45 45 0%
bgpcfgd/runner.py 39 39 0%
bgpcfgd/template.py 64 11 83%
bgpcfgd/utils.py 32 24 25%
bgpcfgd/vars.py 1 0 100%
----------------------------------------------------
TOTAL 1128 530 53%
```
**- Which release branch to backport (provide reason below if selected)**
- [ ] 201811
- [x] 201911
- [x] 202006
**- Why I did it**
FRR introduced [next hop tracking](http://docs.frrouting.org/projects/dev-guide/en/latest/next-hop-tracking.html) functionality.
That functionality requires resolving BGP neighbors before setting BGP connection (or explicit ebgp-multihop command). Sometimes (BGP MONITORS) our neighbors are not directly connected and sessions are IBGP. In this case current configuration prevents FRR to establish BGP connections. Reason would be "waiting for NHT". To fix that we need either add static routes for each not-directly connected ibgp neighbor, or enable command `ip nht resolve-via-default`
**- How I did it**
Put `ip nht resolve-via-default` into the config
**- How to verify it**
Build an image. Enable BGP_MONITOR entry and check that entry is Established or Connecting in FRR
Co-authored-by: Pavel Shirshov <pavel.contrib@gmail.com>
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
implements a new feature: "BGP Allow list."
This feature allows us to control which IP prefixes are going to be advertised via ebgp from the routes received from EBGP neighbors.
implements a new feature: "BGP Allow list."
This feature allows us to control which IP prefixes are going to be advertised via ebgp from the routes received from EBGP neighbors.
Resubmitting the changes for (#4825) with fixes for sonic-bgpcdgd test failures
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
* Adding new BGP peer groups PEER_V4_INT and PEER_V6_INT. The internal BGP sessions
will be added to this peer group while the external BGP sessions will be added
to the exising PEER_V4 and PEER_V6 peer group.
* Check for "ASIC" keyword in the hostname to identify the internal neighbors.
- change the references to 'type' field to 'sub_role'
- change the references to 'InternalFrontend' and 'InternalBackend' to 'FrontEnd' and 'BackEnd' respectively
- add a statement to reflect route-reflector for backend asics
- add a change to set "next-hop-self force" configuration for internal BGP session in multi asic platform.
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
The one big bgp configuration template was splitted into chunks.
Currently we have three types of bgp neighbor peers:
general bgp peers. They are represented by CONFIG_DB::BGP_NEIGHBOR table entries
dynamic bgp peers. They are represented by CONFIG_DB::BGP_PEER_RANGE table entries
monitors bgp peers. They are represented by CONFIG_DB::BGP_MONITORS table entries
This PR introduces three templates for each peer type:
bgp policies: represent policieas that will be applied to the bgp peer-group (ip prefix-lists, route-maps, etc)
bgp peer-group: represent bgp peer group which has common configuration for the bgp peer type and uses bgp routing policy from the previous item
bgp peer-group instance: represent bgp configuration, which will be used to instatiate a bgp peer-group for the bgp peer-type. Usually this one is simple, consist of the referral to the bgp peer-group, bgp peer description and bgp peer ip address.
This PR redefined constant.yml file. Now this file has a setting for to use or don't use bgp_neighbor metadata. This file has more parameters for now, which are not used. They will be used in the next iteration of bgpcfgd.
Currently all tests have been disabled. I'm going to create next PR with the tests right after this PR is merged.
I'm going to introduce better bgpcfgd in a short time. It will include support of dynamic changes for the templates.
FIX:: #4231
