Why I did it
Fix some of vulnerability issue relative python packages #14269
Pillow: [CVE-2021-27921]
Wheel: [CVE-2022-40898]
lxml: [CVE-2022-2309]
How I did it
How to verify it
Why I did it
SONiC currently does not identify 'EdgeZoneAggregator' neighbor. As a result, the buffer profile attached to those interfaces uses the default cable length which could cause ingress packet drops due to insufficient headroom. Hence, there is a need to update the buffer templates to identify such neighbors and assign the same cable length as used by the T1.
How I did it
Modified the buffer template to identify EdgeZoneAggregator as a neighbor device type and assign it the same cable length as a T1/leaf router.
How to verify it
Unit tests pass, and manually checked on a 7260 to see the changes take effect.
Signed-off-by: dojha <devojha@microsoft.com>
Why I did it
This PR addresses the issue mentioned above by loading the acl config as a service on a storage backend device
How I did it
The new acl service is a oneshot service which will start after swss and does some retries to ensure that the SWITCH_CAPABILITY info is present before attempting to load the acl rules. The service is also bound to sonic targets which ensures that it gets restarted during minigraph reload and config reload
How to verify it
Build an image with the following changes and did the following tests
Verified that acl is loaded successfully on a storage backend device after a switch boot up
Verified that acl is loaded successfully on a storage backend ToR after minigraph load and config reload
Verified that acl is not loaded if the device is not a storage backend ToR or the device does not have a DATAACL table
Signed-off-by: Neetha John <nejo@microsoft.com>
- Why I did it
Need to add the possibility to choose between dropping packets (using ACL) on ingress or egress in Dual ToR scenario
- How I did it
Add new attribute "mux_tunnel_ingress_acl" to SYSTEM_DEFAULTS table
- How to verify it
check that new attribute exists in redis:
admin@sonic:~$ redis-cli -n 4
127.0.0.1:6379[4]> HGETALL SYSTEM_DEFAULTS|mux_tunnel_ingress_acl
1."state"
2."false"
Signed-off-by: Andriy Yurkiv <ayurkiv@nvidia.com>
Why I did it
Fix similar issue seen on #13739 but only for DCS-7050CX3-32S
How I did it
Add a kernel parameter to tell libata to disable NCQ
How to verify it
The message ata2.00: FORCE: horkage modified (noncq) should appear on the dmesg.
Test results using: fio --direct=1 --rw=randrw --bs=64k --ioengine=libaio --iodepth=64 --runtime=120 --numjobs=4
with NCQ
READ: bw=26.1MiB/s (27.4MB/s), 26.1MiB/s-26.1MiB/s (27.4MB/s-27.4MB/s), io=3136MiB (3288MB), run=120053-120053msec
WRITE: bw=26.3MiB/s (27.6MB/s), 26.3MiB/s-26.3MiB/s (27.6MB/s-27.6MB/s), io=3161MiB (3315MB), run=120053-120053msec
without NCQ
READ: bw=22.0MiB/s (23.1MB/s), 22.0MiB/s-22.0MiB/s (23.1MB/s-23.1MB/s), io=2647MiB (2775MB), run=120069-120069msec
WRITE: bw=22.2MiB/s (23.3MB/s), 22.2MiB/s-22.2MiB/s (23.3MB/s-23.3MB/s), io=2665MiB (2795MB), run=120069-120069msec
Fixes#13568
Upgrade from old image always requires squashfs mount to get the next image FW binary. This can be avoided if we put FW binary under platform directory which is easily accessible after installation:
admin@r-spider-05:~$ ls /host/image-fw-new-loc.0-dirty-20230208.193534/platform/fw-SPC.mfa
/host/image-fw-new-loc.0-dirty-20230208.193534/platform/fw-SPC.mfa
admin@r-spider-05:~$ ls -al /tmp/image-fw-new-loc.0-dirty-20230208.193534-fs/etc/mlnx/fw-SPC.mfa
lrwxrwxrwx 1 root root 66 Feb 8 17:57 /tmp/image-fw-new-loc.0-dirty-20230208.193534-fs/etc/mlnx/fw-SPC.mfa -> /host/image-fw-new-loc.0-dirty-20230208.193534/platform/fw-SPC.mfa
- Why I did it
202211 and above uses different squashfs compression type that 201911 kernel can not handle. Therefore, we avoid mounting squashfs altogether with this change.
- How I did it
Place FW binary under /host/image-/platform/mlnx/, soft links in /etc/mlnx are created to avoid breaking existing scripts/automation.
/etc/mlnx/fw-SPCX.mfa is a soft link always pointing to the FW that should be used in current image
mlnx-fw-upgrade.sh is updated to prefer /host/image-/platform/mlnx location and fallback to /etc/mlnx in squashfs in case new location does not exist. This is necessary to do image downgrade.
- How to verify it
Upgrade from 201911 to master
master to 201911 downgrade
master -> master reboot
ONIE -> master boot (First FW burn)
Which release branch to backport (provide reason below if selected)
#### Why I did it
Following the PR https://github.com/sonic-net/sonic-swss-common/pull/739 increasing netlink buffer size in linux kernel
As error is seen in fdbsyncd with netlink reports "out of memory on reading a netlink socket" It is seen when kernel is sending 10k remote mac to fdbsyncd.
#### How I did it
Increase the buffer size of the netlink buffer from 3MB to 16MB
#### How to verify it
Verified with 10k remote mac, and restarting the fdbsyncd process. So that kernel send the bridge fdb dump to the fdbsyncd.
Verified that the netlink buffer error is not reported in the sys log.
Go's runtime (and dockerd inherits this) uses own DNS resolver implementation by default on Linux.
It has been observed that there are some DNS resolution issues when executing ```docker pull``` after first boot.
Consider the following script:
```
admin@r-boxer-sw01:~$ while :; do date; cat /etc/resolv.conf; ping -c 1 harbor.mellanox.com; docker pull harbor.mellanox.com/sonic/cpu-report:1.0.0 ; sleep 1; done
Fri 03 Feb 2023 10:06:22 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.99 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.989/5.989/5.989/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:57245->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:23 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.56 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.561/5.561/5.561/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:53299->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:24 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.78 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.783/5.783/5.783/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:55765->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:25 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=7.17 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 7.171/7.171/7.171/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:44877->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:26 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=5.66 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 5.656/5.656/5.656/0.000 ms
Error response from daemon: Get "https://harbor.mellanox.com/v2/": dial tcp: lookup harbor.mellanox.com on [::1]:53: read udp [::1]:54604->[::1]:53: read: connection refused
Fri 03 Feb 2023 10:06:27 AM UTC
nameserver 10.211.0.124
nameserver 10.211.0.121
nameserver 10.7.77.135
search mtr.labs.mlnx labs.mlnx mlnx lab.mtl.com mtl.com
PING harbor.mellanox.com (10.7.1.117) 56(84) bytes of data.
64 bytes from harbor.mtl.labs.mlnx (10.7.1.117): icmp_seq=1 ttl=53 time=8.22 ms
--- harbor.mellanox.com ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 8.223/8.223/8.223/0.000 ms
1.0.0: Pulling from sonic/cpu-report
004f1eed87df: Downloading [===================> ] 19.3MB/50.43MB
5d6f1e8117db: Download complete
48c2faf66abe: Download complete
234b70d0479d: Downloading [=========> ] 9.363MB/51.84MB
6fa07a00e2f0: Downloading [==> ] 9.51MB/192.4MB
04a31b4508b8: Waiting
e11ae5168189: Waiting
8861a99744cb: Waiting
d59580d95305: Waiting
12b1523494c1: Waiting
d1a4b09e9dbc: Waiting
99f41c3f014f: Waiting
```
While /etc/resolv.conf has the correct content and ping (and any other utility that uses libc's DNS resolution implementation) works correctly
docker is unable to resolve the hostname and falls back to default [::1]:53. This started to happen after PR https://github.com/sonic-net/sonic-buildimage/pull/13516 has been merged.
As you can see from the log, dockerd is able to pick up the correct /etc/resolv.conf only after 5 sec since first try. This seems to be somehow related to the logic in Go's DNS resolver
https://github.com/golang/go/blob/master/src/net/dnsclient_unix.go#L385.
There have been issues like that reported in docker like:
- https://github.com/docker/cli/issues/2299
- https://github.com/docker/cli/issues/2618
- https://github.com/moby/moby/issues/22398
Since this starts to happen after inclusion of resolvconf package by
above mentioned PR and the fact I can't see any problem with that (ping,
nslookup, etc. works) the choice is made to force dockerd to use cgo
(libc) resolver.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
- Why I did it
Added platform specific script to be invoked during SAI failure dump. Added some generic changes to mount /var/log/sai_failure_dump as read write in the syncd docker
- How I did it
Added script in docker-syncd of mellanox and copied it to /usr/bin
- How to verify it
Manual UT and new sonic-mgmt tests
Why I did it
Fix some unreliability seen on emmc device with some AMD CPUs
How I did it
Added a kernel parameter to add quirks to
It depends on a sonic-linux-kernel change to work properly but will be a no-op without it.
The quirk added is SDHCI_QUIRK2_BROKEN_HS200 used to downgrade the link speed for the eMMC.
Why I did it
To address error sometimes seen when running sonic-mgmt test_stress_routes.py::test_announce_withdraw_route on 720DT-48S
How I did it
Update boot0 logic to set platform specific varlog size for 720DT-48S
How to verify it
Verified that /var/log size increased and error is no longer observed when running test
- Why I did it
In to-sonic and multi-asic KVM-test, pretest sometimes failed. Reason is rsyslogd process can not start in teamd container. Because rsyslog.conf is empty caused by sonic-cfggen execute failed
- How I did it
If sonic-cfggen -d execute failed, execute without -d because the template file has the default value.
- How to verify it
Build image and test it over 40 times, all passed pretest.
Signed-off-by: Chun'ang Li <chunangli@microsoft.com>
- Why I did it
fixes#12907
When the management interface IP address configuration changes from dynamic to static the DNS configuration (retrieved from the DHCP server) in /etc/resolv.conf remains uncleared. This leads to a DNS configuration pointing to the wrong nameserver. To make the behavior clear DNS configuration received from DHCP should be cleared.
- How I did it
Use resolvconf package for managing DNS configuration. It is capable of tracking the source of DNS configuration and puts the configuration retrieved from the DHCP servers into a separate file. This allows the implementation of DNS configuration cleanup retrieved from DHCP during networking reconfiguration.
- How to verify it
Ensure that the management interface has no static configuration.
Check that /etc/resolv.conf has DNS configuration.
Configure a static IP address on the management interface.
Verify that /etc/resolv.conf has no DNS configuration.
Remove the static IP address from the management interface.
Verify that /etc/resolv.conf has DNS configuration retrieved form DHCP server.
After upgrade to brcmsai 8.1, the sdk running environment (container) recommended with mininum memory size as below
TH4/TD4(ltsw) uses 512MB
TH3 used 300MB
Helix4/TD2/TD3/TH/TH 256 MB
Base on this requirement, adjust the default syncd share memory size and set the memory size for special ACISs in platform_env.conf file for different types of Broadcom ASICs.
How I did it
Add the platform_env.conf file if none of it for broadcom platform (base on platform_asic file)
Add the 'SYNCD_SHM_SIZE' and set the value
for ltsw(TD4/TH4) devices set to 512M at least (update the platform_env.conf)
for Td2/TH2/TH devices set to 256M
for TH3 set to 300M
verify
How to verify it
verify the image with code fix
Check with UT
Check on lab devices
On a problematic device which cannot start successfully
Run with the command
$ cat /proc/linux-kernel-bde
Broadcom Device Enumerator (linux-kernel-bde)
Module parameters:
maxpayload=128
usemsi=0
dmasize=32M
himem=(null)
himemaddr=(null)
DMA Memory (kernel): 33554432 bytes, 0 used, 33554432 free, local mmap
No devices found
$ docker rm -f syncd
syncd
$ sudo /usr/bin/syncd.sh start
Cannot get Broadcom Chip Id. Skip set SYNCD_SHM_SIZE.
Creating new syncd container with HWSKU Force10-S6000
a4862129a7fea04f00ed71a88715eac65a41cdae51c3158f9cdd7de3ccc3dd31
$ docker inspect syncd | grep -i shm
"ShmSize": 67108864,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
On Normal device
$ docker inspect syncd | grep -i shm
"ShmSize": 268435456,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e"
change the config syncd_shm.ini to b85=128m
$ docker rm -f syncd
syncd
$ sudo /usr/bin/syncd.sh start
Creating new syncd container with HWSKU Force10-S6000
3209ffc1e5a7224b99640eb9a286c4c7aa66a2e6a322be32fb7fe2113bb9524c
$ docker inspect syncd | grep -i shm
"ShmSize": 134217728,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
change the config under
/usr/share/sonic/device/x86_64-dell_s6000_s1220-r0/Force10-S6000/platform_env.conf
and run command
$ cat /usr/share/sonic/device/x86_64-dell_s6000_s1220-r0/platform_env.conf
SYNCD_SHM_SIZE=300m
$ sudo /usr/bin/syncd.sh start
Creating new syncd container with HWSKU Force10-S6000
897f6fcde1f669ad2caab7da4326079abd7e811bf73f018c6dacc24cf24bfda5
$ docker inspect syncd | grep -i shm
"ShmSize": 314572800,
"Tag": "fix_8.1_shm_issue.67873427-9f7ca60a0e",
Signed-off-by: richardyu-ms <richard.yu@microsoft.com>
Changing the default config knob value to be True for killing radv, due to the reasons below:
Killing RADV is to prevent sending the "cease to be advertising interface" protocol packet.
RFC 4861 says this ceasing packet as "should" instead of "must", considering that it's fatal to not do this.
In active-active scenario, host side might have difficulty distinguish if the "cease to be advertising interface" is for the last interface leaving.
6.2.5. Ceasing To Be an Advertising Interface
shutting down the system.
In such cases, the router SHOULD transmit one or more (but not more
than MAX_FINAL_RTR_ADVERTISEMENTS) final multicast Router
Advertisements on the interface with a Router Lifetime field of zero.
In the case of a router becoming a host, the system SHOULD also
depart from the all-routers IP multicast group on all interfaces on
which the router supports IP multicast (whether or not they had been
advertising interfaces). In addition, the host MUST ensure that
subsequent Neighbor Advertisement messages sent from the interface
have the Router flag set to zero.
sign-off: Jing Zhang zhangjing@microsoft.com
During docker build, host files can be passed to the docker build through
docker context files. But there is no straightforward way to transfer
the files from docker build to host.
This feature provides a tricky way to pass the cache contents from docker
build to host. It tar's the cached content and encodes them as base64 format
and passes it through a log file with a special tag as 'VCSTART and VCENT'.
Slave.mk in the host, it extracts the cache contents from the log and stores them
in the cache folder. Cache contents are encoded as base64 format for
easy passing.
<!--
Please make sure you've read and understood our contributing guidelines:
https://github.com/Azure/SONiC/blob/gh-pages/CONTRIBUTING.md
** Make sure all your commits include a signature generated with `git commit -s` **
If this is a bug fix, make sure your description includes "fixes #xxxx", or
"closes #xxxx" or "resolves #xxxx"
Please provide the following information:
-->
#### Why I did it
#### How I did it
#### How to verify it
* [Security] Upgrade the openssl version to 1.1.1n-0+deb11u4+fips (#13737)
Why I did it
[Security] Upgrade the openssl version to 1.1.1n-0+deb11u4+fips
f6df7303d8 Update expired certs.
84540b59c1 CVE-2022-2068
f763d8a93e Prepare 1.1.1n-0+deb11u2
576562cebe CVE-2022-1292
How I did it
Upgrade the OpenSSL version
* [Security] Upgrade OpenSSL version for armhf
Adding /usr/local/bin/storyteller to READ_ONLY_CMDS. So no write access or prompt for password is needed to run storyteller.
Tested on 202205 clusters, user who didn't request write access was able to grep log using storyteller.
sign-off: Jing Zhang zhangjing@microsoft.com
- Why I did it
This optimization is needed for DPU SONiC. DPU SONiC runs a limited set of containers and teamd and radv containers are not part of them. Unlike the other containers, there was no possibility to disable teamd and radv containers compilation.
To reduce DPU SONiC compilation time and reduce the image size this commit adds the possibility to disable their compilation.
- How I did it
Two new configuration options are added to rules/config file:
INCLUDE_TEAMD
INCLUDE_ROUTER_ADVERTISER
By default to preserve the existing behavior both options are enabled. There are two ways to override them:
To change option value to "n" in rules/config file.
To override their value using SONIC_OVERRIDE_BUILD_VARS env variable:
SONIC_OVERRIDE_BUILD_VARS="SONIC_INCLUDE_TEAMD=y SONIC_INCLUDE_ROUTER_ADVERTISER=n"
- How to verify it
The default behavior is preserved. To verify it compile the image without overriding new options. Install the image and verify that both teamd and radv containers are present and running.
To verify the new options override them with "n" value. Compile and install image. Verify that no docker containers are present. Verify that SWSS can start without errors.
Debian is shipping a systemd timer unit for logrotate, but we're also
packaging in a cron job, which means both of them will run, potentially
at the same time. Remove our cron file, and add an override to the
shipped timer file to have it be run every 10 minutes.
Fixes#12392.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
#### Why I did it
Segfault was occuring when running memory_checker
#### How I did it
Deinit publisher immediately after publishing
#### How to verify it
Manual testing
Backport of https://github.com/sonic-net/sonic-buildimage/pull/12490 into 202211
- Why I did it
Support syslog rate limit configuration feature
- How I did it
Remove unused rsyslog.conf from containers
Modify docker startup script to generate rsyslog.conf from template files
Add metadata/init data for syslog rate limit configuration
- How to verify it
Manual test
New sonic-mgmt regression cases
