Why I did it
fstrim has dependency on pmon docker.
How I did it
start fstrim timer after sonic.target.
How to verify it
local test and PR test.
Signed-off-by: Ying Xie ying.xie@microsoft.com
The Lodoga platform also matched crow which was hardcoding the flash
size to 3700. This change enables autodetect on Clearlake which in turns
allows autodetect for Lodoga.
The threshold was bumped from 3700 to 4000 because size computation can
differ slightly and report slightly above 3700.
Lodoga actually has a 8GB storage device.
LodogaSsd variant has a 30GB SSD drive.
However, in boot0 both were mishandled and assigned 4GB for legacy reasons.
Remove the hardcoding of the flash size and let boot0 autodetect the available space.
This commit adds support for changing the default console baud rate configured
within the U-Boot bootloader. That default baud rate is exposed via the value
of the U-Boot 'baudrate' environment variable. This commit removes logic that
hardcoded the console baud rate to 115200 and instead ensures that the U-Boot
'baudrate' variable is always used when constructing the Linux kernel boot
arguments used when booting Sonic.
A change is also made to rc.local to ensure that the specified baud rate is set
correctly in the serial getty service.
*To run VNET route consistency check periodically.
*For any failure, the monit will raise alert based on return code.
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
Enable fib_multipath_use_neigh for v4
https://www.kernel.org/doc/Documentation/networking/ip-sysctl.txt
Why I did:
This is helpful if the neighbor are not directly connected then Kernel forward to unreachable neighbor option. With this option forwarding using neighbor state to be valid.
#### Why I did it
Use a predefined variable to get vendor information when the swss docker container is created
#### How I did it
Use `{{ sonic_asic_platform }}` instead of `$SONIC_CFGGEN -y /etc/sonic/sonic_version.yml -v asic_type`
#### How to verify it
Manually test.
Master/202012 image size grew quite a bit. 3.7G harddrive can no longer hold one image and safely upgrade to another image. Every bit of harddrive space is precious to save now.
Also sh syntax seemingly changed, [ condition ] && action was a legit syntax in 201911 branch but it is an error when condition not met with 202012 or later images. Change the syntax to if statement to avoid the issue.
Signed-off-by: Ying Xie ying.xie@microsoft.com
Fix#7968
Issue is detected on SONiC.20201231.11
In test_static_route.py::test_static_route_ecmp static routes are configured, but neighbors are not resolved after config reload even after 10 minutes.
It looks like the arp_update script is starting to ping when Vlan1000 is not fully configured.
When issue is reproduced, stuck ping6 process is observed in swss container :
USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND
root 180 0.1 0.0 6296 1272 pts/0 S 17:03 0:03 ping6 -I Vlan1000 -n -q -i 0 -c 1 -W 0 ff02::1
And when arp_update script successfully resolves neighbors, we observe sleep 300 instead of ping process
In version 3.0.0, If a broadcast address is specified in
/etc/network/interfaces, then when ifup is run, it will fail with an
error saying `'str' object has no attribute 'packed'`. This appears to
be because it expects all attributes for an interface to be "packable"
into a compact binary representation. However, it doesn't actually
convert the broadcast address into an IPNetwork object (other addresses
are handled).
Therefore, convert the broadcast address it reads in from a str to an
IPNetwork object.
Also explicitly specify the scope of the loopback address in
/etc/network/interfaces as host scope. Otherwise, it will get added as
global scope by default. As part of this, use JSON to parse ip's output
instead of text, for robustness.
Signed-off-by: Saikrishna Arcot <sarcot@microsoft.com>
Use DOCKER_HOST. Every client including docker command and python docker API uses this environment variable to connect to dockerd.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
the branch refers the branch name that the commit is in,
for example master, 202012, 201911, ...
In case there is no branch, the name will be HEAD.
release is encoded in /etc/sonic/sonic_release file.
the file is only available for a release branch.
It is not available in master branch.
example for master branch
```
build_version: 'master.602-6efc0a88'
debian_version: '10.7'
kernel_version: '4.19.0-9-2-amd64'
asic_type: vs
commit_id: '6efc0a88'
branch: 'master'
release: 'none'
build_date: Tue Dec 29 06:54:02 UTC 2020
build_number: 602
built_by: johnar@jenkins-worker-23
```
example for 202012 release branch
```
build_version: '202012.602-6efc0a88'
debian_version: '10.7'
kernel_version: '4.19.0-9-2-amd64'
asic_type: vs
commit_id: '6efc0a88'
branch: '202012'
release: '202012'
build_date: Tue Dec 29 06:54:02 UTC 2020
build_number: 602
built_by: johnar@jenkins-worker-23
```
Signed-off-by: Guohan Lu <lguohan@gmail.com>
#### Why I did it
* `arp_update` fails to ping those neighbors over vlan sub interfaces.
#### How I did it
* modify `arp_update_vars.j2` to get vlan sub interfaces with ipv6 addresses assigned.
* modify `arp_update` to send ipv6 pings over those retrieved vlan sub interfaces.
Signed-off-by: Longxiang Lyu <lolv@microsoft.com>
This change is to add a gbsyncd container to accommodate the syncd process and the SAI libraries for the Credo gearbox chips.
How I did it
This container works similar to the existing Broadcom syncd container. Its main difference is that the SAI-related dynamic libraries are replaced by the ones for Credo gearbox chips, and the container only reacts to SAI events for the gearbox chips. The SAI libraries will be provided by the package libsai-credo_1.0_amd64.deb.
For the image build, the added container will be built and included in the Broadcom platform image, after $(LIBSAI_CREDO)_URL = is replaced to the correct value. For now, as $(LIBSAI_CREDO)_URL is empty, the container build is skipped in the image build.
After the container is included in the image, in the runtime, the container will begin with checking the existence of /usr/share/sonic/hwsku/gearbox_config.json; if that file is not provided, the container will exit by itself. Therefore, for platforms unrelated to the Credo chips, as long as they are not providing the file, they will not be affected by this change.
This PR creates a directory firmware on the HOST with the path /usr/share/sonic/firmware, as well as this is
mounted on PMON container with the same path /usr/share/sonic/firmware. This is required for firmware
upgrade support for muxcable as currently by design all Y-Cable API's are called by xcvrd. As such if CLI has
to transfer a file to PMON we need to mount a directory from host to PMON just for getting the firmware files.
Hence we require this change.
Signed-off-by: vaibhav-dahiya <vdahiya@microsoft.com>
Changes to allow starting per asic services like swss and syncd only if the platform vendor codedetects the asic is detected and notified. The systemd services ordering we want is database->database@->pmon->swss@->syncd@->teamd@->lldp@
There is also a requirement that management, telemetry, snmp dockers can start even if all asic services are not up.
Why I did it
For VOQ chassis, the fabric cards will have 1-N asics. Also, there could be multiple removable fabric cards. On the supervisor, swss and syncd containers need to be started only if the fabric-card is in Online state and respective asics are detected by the kernel. Using systemd, the dependent services can be in inactive state.
How I did it
Introduce a mechanism where all ASIC dependent service wait on its state to be published via PMON to REDIS. Once the subscription is received, the service proceeds to create respective dockers.
For fixed platforms, systemd is unchanged i.e. the service bring up and docker creation happens in the start()/ExecStartPre routine of the .sh scripts.
For VOQ chassis platform on supervisor, the service bringup skips docker creation in the start() routine, but does it in the wait()/ExecStart routine of the .sh scrips.
Management dockers are decoupled from ASIC docker creation.
- Why I did it
Make DHCP relay docker an extension. DHCP relay now carries dhcp relay commands CLI plugin and has a complete manifest.
It is installed as extension if INCLUDE_DHCP_REALY is set to y.
DEPENDS on #5939
- How I did it
Modify DHCP relay docker makefile and dockerfile. Make changes to sonic_debian_extension.j2 to install sonic packages.
I moved DHCP related CLI tests from sonic-utilities to DHCP relay docker.
This PR introduces a way to write a plugin as part of docker image and run the tests from cli-plugin-tests directory under docker directory.
The test result is available in target/docker-dhcp-relay.gz.log:
[ REASON ] : target/docker-dhcp-relay.gz does not exist NON-EXISTENT PREREQUISITES: docker-start target/docker-config-engine-buster.gz-load target/python-wheels/sonic_utilities-1.2-py3-none-any.whl-in
stall target/debs/buster/python3-swsscommon_1.0.0_amd64.deb-install
[ FLAGS FILE ] : []
[ FLAGS DEPENDS ] : []
[ FLAGS DIFF ] : []
============================= test session starts ==============================
platform linux -- Python 3.7.3, pytest-3.10.1, py-1.7.0, pluggy-0.8.0 -- /usr/bin/python3
cachedir: .pytest_cache
rootdir: /sonic/dockers/docker-dhcp-relay/cli-plugin-tests, inifile:
plugins: cov-2.6.0
collecting ... collected 10 items
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_plugin_registration PASSED [ 10%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_nonexist_vlanid PASSED [ 20%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_invalid_vlanid PASSED [ 30%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_invalid_ip PASSED [ 40%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_dhcp_relay_with_exist_ip PASSED [ 50%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_add_del_dhcp_relay_dest PASSED [ 60%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_remove_nonexist_dhcp_relay_dest PASSED [ 70%]
test_config_dhcp_relay.py::TestConfigVlanDhcpRelay::test_config_vlan_remove_dhcp_relay_dest_with_nonexist_vlanid PASSED [ 80%]
test_show_dhcp_relay.py::TestVlanDhcpRelay::test_plugin_registration PASSED [ 90%]
test_show_dhcp_relay.py::TestVlanDhcpRelay::test_dhcp_relay_column_output PASSED [100%]
=============================== warnings summary ===============================
/usr/local/lib/python3.7/dist-packages/tabulate.py:7
/usr/local/lib/python3.7/dist-packages/tabulate.py:7: DeprecationWarning: Using or importing the ABCs from 'collections' instead of from 'collections.abc' is deprecated, and in 3.8 it will stop working
from collections import namedtuple, Iterable
-- Docs: https://docs.pytest.org/en/latest/warnings.html
==================== 10 passed, 1 warnings in 0.35 seconds =====================
#### Why I did it
I made this change to support warm/fast reboot for SONiC extension packages as per HLD Azure/SONiC#682.
#### How I did it
I extended manifest.json.j2 with new warm/fast reboot related fields and also extended sonic_debian_extension.j2 script template to generate the shutdown order files for warm and fast reboot.
After https://github.com/Azure/sonic-buildimage/pull/7598 the packages.json generation is broken. This change fixes it make the whole build fail in case generation failed.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
- Why I did it
Currently dhcp packets are disabled by the COPP manager for non ToRRouter type switches.
Even if the feature is enabled, DHCP packets wont hook to the CPU since the COPP manager will not trap this packets.
This change is to disable dhcp_relay by default for non ToRRouter switches from init_cfg.json.
With this approach, if the user want to enable the feature for non ToRRouter switches, manual enablement is required by the 'feature' configuration.
This is to keep the current approach for MSFT production issue with dhcp relay for non ToRRouter switched and allow the user to decide if to use it or not.
- How I did it
Configure dhcp_relay 'disabled' by default on init_cfg.json for non ToRRouter switches.
Remove the exclusion of dhcp packets on copp_cfg.json
- How to verify it
Enable dhcp_relay feature on a non ToRRouter switch.
Unit-tests modified so the default values on mocked CONFIG DB in 'test_vectors.py' for dhcp_relay will be 'disabled'.
This is by the change for 'init_cfg.json.j2'.
For ToRRouter the state will change from 'disabled' to 'enabled'.
Another test case added for a 'ToR' switch type, this is to test the state is 'enabled' if the user configured it to be so.
dash doesn't support += operation to append to a variable's value. Use KDUMP_CMDLINE_APPEND="${KDUMP_CMDLINE_APPEND} " instead
The below error message is seen when a reboot is issued.
[ 342.439096] kdump-tools[13655]: /etc/init.d/kdump-tools: 117: /etc/default/kdump-tools: KDUMP_CMDLINE_APPEND+= panic=10 debug hpet=disable pcie_port=compat pci=nommconf sonic_platform=x86_64-accton_as7326_56x-r0: not found
The voq system lag id boundary is set in redis-chassis. Changes include
setting this from database-chassis container. This fixes a timing issue
in finding datbase_config.json file from redis directory which is
created from database container. Since database container usually
starts after database-chassis container the existence of this file is
unreliable while running the command. Running the command under
database-chassis container makes sure that the database_config.json form
redis-chassis directory is guaranteed to be available and hence fixes the
timing issue.
Signed-off-by: vedganes <vedavinayagam.ganesan@nokia.com>
Signed-off-by: Stepan Blyschak stepanb@mellanox.com
Why I did it
To support building DHCP relay as extension and installing it during build time.
How I did it
Created infrastructure. Users need to define their packages in rules/sonic-packages.mk
How to verify it
Together with #6531
Before this change, a process running inside every SONiC container dealt with FEATURE table 'auto_restart' field and depending on the value decided whether a container has to be killed or not.
If killed service auto restart mechanism restarts the container.
This change moves the logic from container to the host daemon - hostcfgd.
The 'auto_restart' handling is kept in supervisor-proc-exit-listener but now it is not required for container that wants to support auto restart feature.
hostcfgd refactoring - move feature handling in another class.
override systemd service Restart= setting from hostcfgd.
remove default systemd Restart=always.
Signed-off-by: Stepan Blyshchak stepanb@nvidia.com
- Why I did it
Remove the need to deal with container orchestration logic from the container itself. Leave this logic to the orchestrator - host OS.
- How I did it
hostcfgd configures 'Restart=' value for systemd service.
- How to verify it
root@r-tigon-11:/home/admin# sudo config feature autorestart lldp enabled
root@r-tigon-11:/home/admin# show feature status | grep lldp
lldp enabled enabled
root@r-tigon-11:/home/admin# docker exec -it lldp pkill -9 lldpd
root@r-tigon-11:/home/admin# docker ps -a | grep lldp
65058396277c docker-lldp:latest "/usr/bin/docker-lld…" 2 days ago Exited (0) 20 seconds ago lldp
root@r-tigon-11:/home/admin# docker ps -a | grep lldp
65058396277c docker-lldp:latest "/usr/bin/docker-lld…" 2 days ago Up 5 seconds lldp
root@r-tigon-11:/home/admin# sudo config feature autorestart lldp disabled
root@r-tigon-11:/home/admin# docker exec -it lldp pkill -9 lldpd
root@r-tigon-11:/home/admin# docker ps -a | grep lldp
65058396277c docker-lldp:latest "/usr/bin/docker-lld…" 2 days ago Up 35 seconds lldp
root@r-tigon-11:/home/admin# docker ps -a | grep lldp
65058396277c docker-lldp:latest "/usr/bin/docker-lld…" 2 days ago Exited (0) 3 seconds ago lldp
root@r-tigon-11:/home/admin# docker ps -a | grep lldp
65058396277c docker-lldp:latest "/usr/bin/docker-lld…" 2 days ago Exited (0) 39 seconds ago lldp
root@r-tigon-11:/home/admin#
#### Why I did it
- To build flashrom properly with dependency tracking.
#### How I did it
- Moved flashrom code from platform/broadcom/sonic-platform-modules-dell/tools directory to src/flashrom directory.
- At the end, flashrom_0.9.7_amd64.deb package is build which will be installed in the devices.
- Currently flashrom builds only for Dell S6100 platforms.
Introduce new sonic-buildimage images for Broadcom DNX ASIC family.
sonic-broadcom-dnx.bin
sonic-aboot-broadcom-dnx.swi
How I did it
NO CHANGE to existing make commands
make init; make configure PLATFORM=broadcom; make target/sonic-aboot-broadcom.swi; make target/sonic-broadcom.bin
The difference now is that it will result in new broadcom images for DNX asic family as well.
sonic-broadcom.bin, sonic-broadcom-dnx.bin
sonic-aboot-broadcom.swi, sonic-aboot-broadcom-dnx.swi
Note: This PR also adds support for Broadcom SAI 5.0 (based on 1.8 SAI ) for DNX based platform + changes in platform x86_64-arista_7280cr3_32p4 bcm config files and platform_env.conf files
#### Why I did it
Following the discussion in another PR https://github.com/Azure/sonic-buildimage/pull/7708#discussion_r642933510 , since there will be multi subfolders under **/var/log/mellanox**, so we agreed to only mount this folder and the subfolders will be created afterward on demand.
#### How I did it
during the syncd docker creation, only mount folder **/var/log/mellanox**
#### How to verify it
build an Mellanox image and verify the related folder on the host and docker side.
#### Why I did it
Create a target for delayed service timers. Few services in sonic have delayed to speed up the bring up of the system and essential services. However there is no way to track when they start. This will be a problem when executing config reload as config reload expects all services to be up. Hence grouped all the timers that trigger the delayed services under one target so that they could be tracked in 'config reload' command
#### How I did it
Created delay.target service and add created dependency on the delayed targets.
Why I did it
Support multiple pcie configuration file and change the pcie status table name
This is to match with below two PRs.
Azure/sonic-platform-common#195Azure/sonic-platform-daemons#189
How I did it
Check pcie configuration file with wild card and change the device status table name
How to verify it
Restart with changes and see if the pcie check works as expected.
Why I did it
The SONiC switches get their docker images from local repo, populated during install with container images pre-built into SONiC FW. With the introduction of kubernetes, new docker images available in remote repo could be deployed. This requires dockerd to be able to pull images from remote repo.
Depending on the Switch network domain & config, it may or may not be able to reach the remote repo. In the case where remote repo is unreachable, we could potentially make Kubernetes server to also act as http-proxy.
How I did it
When admin explicitly enables, the kubernetes-server could be configured as docker-proxy. But any update to docker-proxy has to be via service-conf file environment variable, implying a "service restart docker" is required. But restart of dockerd is vey expensive, as it would restarts all dockers, including database docker.
To avoid dockerd restart, pre-configure an http_proxy using an unused IP. When k8s server is enabled to act as http-proxy, an IP table entry would be created to direct all traffic to the configured-unused-proxy-ip to the kubernetes-master IP. This way any update to Kubernetes master config would be just manipulating IPTables, which will be transparent to all modules, until dockerd needs to download from remote repo.
How to verify it
Configure a switch such that image repo is unreachable
Pre-configure dockerd with http_proxy.conf using an unused IP (e.g. 172.16.1.1)
Update ctrmgrd.service to invoke ctrmgrd.py with "-p" option.
Configure a k8s server, and deploy an image for feature with set_owner="kube"
Check if switch could successfully download the image or not.
Why I did it
This PR adds changes in sonic-config-engine to consume configuration data in SONiC Yang schema and generate config_db entries
How I did it
Add a new file sonic_yang_cfg_generator .
This file has the functions to
parse yang data json and convert them in config_db json format.
Validate the converted config_db entries to make sure all the dependencies and constraints are met.
Add a new option -Y to the sonic-cfggen command for this purpose
Add unit tests
This capability is support only in sonic-config-engine Python3 package only
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
Currently we leveraged the Supervisor to monitor the running status of critical processes in each container and it is more reliable and flexible than doing the monitoring by Monit. So we removed the functionality of monitoring the critical processes by Monit.
How I did it
I removed the script process_checker and corresponding Monit configuration entries of critical processes.
How to verify it
I verified this on the device str-7260cx3-acs-1.
Why I did it
In upgrade scenarios, where config_db.json is not carry forwarded to new image, it could be left w/o TACACS credentials.
Added a service to trigger 5 minutes after boot and restore TACACS, if /etc/sonic/old_config/tacacs.json is present.
How I did it
By adding a service, that would fire 5 mins after boot.
This service apply tacacs if available.
How to verify it
Upgrade and watch status of tacacs.timer & tacacs.service
You may create /etc/sonic/old_config/tacacs.json, with updated credentials
(before 5mins after boot) and see that appears in config & persisted too.
Which release branch to backport (provide reason below if selected)
201911
202006
202012
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
This PR aims to monitor the memory usage of streaming telemetry container and restart streaming telemetry container if memory usage is larger than the pre-defined threshold.
How I did it
I borrowed the system tool Monit to run a script memory_checker which will periodically check the memory usage of streaming telemetry container. If the memory usage of telemetry container is larger than the pre-defined threshold for 10 times during 20 cycles, then an alerting message will be written into syslog and at the same time Monit will run the script restart_service to restart the streaming telemetry container.
How to verify it
I verified this implementation on device str-7260cx3-acs-1.
- Why I did it
To give SONiC Application Extension developers an environment to run and develop their apps.
- How I did it
Created sonic-sdk and sonic-sdk-buildenv dockers and their dbg versions.
- How to verify it
Build:
$ make -f slave target/sonic-sdk.gz target/sonic-sdk-buildenv.gz
#### Why I did it
If a process limits using nodes by mempolicy/cpusets, and those nodes become memory exhaustion status, one process may be killed by oom-killer.
No panic occurs in this case, because other node's memory may be free.
This means system total status may be not fatal yet.
#### How I did it
Remove 'vm.panic_on_oom=1' kernel flag from 'vmcore-sysctl.conf '
Why I did it
Currently, there is a bug in the ntp.conf jinja2 template where it will ignore the src_intf directive in CONFIG_DB if there are multiple IP addresses associated with an interface. This code change fixes that bug and allows the template to select the correct source interface for NTP.
How I did it
I did this by modifying the macro in ntp.conf.j2 which determines if there is an ip address associated with an interface to set a state variable when it detects a valid interface entry in CONFIG_DB instead of outputting "true" directly (which could result in multiple "trues" outputted for interfaces with multiple valid IP addresses).
How to verify it
Add two ipv4 addresses to an interface in SONiC
Add the following configuration to config_db.json
{
"NTP": {
"global": {
"src_intf": "Ethernet1"
}
}
}
Replace Ethernet1 with the interface name of the one you assigned the IP addresses to.
Run sudo config reload -y
Open /etc/ntp.conf and verify that the following line exists
...
interface listen Ethernet1
...
The interface specified should be the one set in the previous steps.
Description for the changelog
[ntp] Fix ntp.conf template to allow setting of source port in CONFIG_DB
Map priority 0 to TC 1 and priority 1 to TC 0
Send traffic on priority 0 and 1 and verified that it gets mapped correctly in hw
Signed-off-by: Neetha John <nejo@microsoft.com>
Why I did it
start pcie-check.service after config-setup.service since pcie_util depends on device_info which is available with config db metadata.
How I did it
Add config-setup.service as a dependency of pcie-check.service
How to verify it
Upon reboot, check if the pcie-check.sh throws the platform api error which is dependent on DEVICE_METADATA
Why I did it
Finding running containers through "docker ps" breaks when kubernetes deploys container, as the names are mangled.
How I did it
The data is is available from FEATURE table, which takes care of kubernetes deployment too.
How to verify it
Deploy a feature via kubernetes and don't expect error from container_check.
Signed-off-by: Stepan Blyschak stepanb@nvidia.com
This PR is part of SONiC Application Extension
Depends on #5938
- Why I did it
To provide an infrastructure change in order to support SONiC Application Extension feature.
- How I did it
Label every installable SONiC Docker with a minimal required manifest and auto-generate packages.json file based on
installed SONiC images.
- How to verify it
Build an image, execute the following command:
admin@sonic:~$ docker inspect docker-snmp:1.0.0 | jq '.[0].Config.Labels["com.azure.sonic.manifest"]' -r | jq
Cat /var/lib/sonic-package-manager/packages.json file to verify all dockers are listed there.
Why I did it
Support readonly version of the command vtysh
How I did it
Check if the command starting with "show", and verify only contains single command in script.
Fix#7364
99-default.link - was always in SONiC, but previous systemd (<247) had an issue and it did not work due to issue systemd/systemd#3374. Now systemd 247 works.
However, such policy overrides teamd provided mac address which causes teamd netdev to use a random mac
address. Therefore, needs to be disabled.
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
#### Why I did it
To build flashrom properly with dependency tracking.
#### How I did it
Moved flashrom code from platform/broadcom/sonic-platform-modules-dell/tools directory to src/flashrom directory.
At the end, flashrom_0.9.7_amd64.deb package is build which will be installed in the devices.
Why I did it
Recent systemd upgrade from #7228 requires an extra cmdline parameter for dockerd to start properly.
Updating boot0 was missed as part of the systemd upgrade change.
How I did it
Just added the missing cmdline parameter in files/Aboot/boot0.j2
This change fixes#7372
How to verify it
Boot the image and dockerd should start normally.
Encounter error during "config-setup boot" if the updategraph is enabled.
How I did it
Correct the code inside the config-setup script.
Remove the space between the assignment operator.
How to verify it
Remove the /etc/sonic/config_db.json and reboot the device.
Originally, it will return following error after boot up.
rv: command not found
After modification, it can correctly parse the status of updategraph without error.
- Support compile sonic arm image on arm server. If arm image compiling is executed on arm server instead of using qemu mode on x86 server, compile time can be saved significantly.
- Add kernel argument systemd.unified_cgroup_hierarchy=0 for upgrade systemd to version 247, according to #7228
- rename multiarch docker to sonic-slave-${distro}-march-${arch}
Co-authored-by: Xianghong Gu <xgu@centecnetworks.com>
Co-authored-by: Shi Lei <shil@centecnetworks.com>
This commit has following changes:
* Add templates and code to support VoQ chassis iBGP peers
* Add support to convert a new VoQChassisInternal element in the
BGPSession element of the minigraph to a new BGP_VOQ_CHASSIS_NEIGHBOR
table in CONFIG_DB.
* Add a new set of "voq_chassis" templates to docker-fpm-frr
* Add a new BGP peer manager to bgpcfgd to add neighbors from the
BGP_VOQ_CHASSIS_NEIGHBOR table using the voq_chassis templates.
* Add a test case for minigraph.py, making sure the VoQChassisInternal
element creates a BGP_VOQ_CHASSIS_NEIGHBOR entry, but not if its
value is "false".
* Add a set of test cases for the new voq_chassis templates in
sonic-bgpcfgd tests.
Note that the templates expect the new
"bgp bestpath peer-type multipath-relax" bgpd configuration to be
available.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
Since we introduced a new value always_disabled for the state field in FEATURE table, the expected running container list
should exclude the always_diabled containers. This bug was found by nightly test and posted at here: issue. This PR fixes#7210.
How I did it
I added a logic condition to decide whether the value of state field of a container was always_disabled or not.
How to verify it
I verified this on the device str-dx010-acs-1.
Which release branch to backport (provide reason below if selected)
201811
201911
202006
[ x] 202012
Signed-off-by: vedganes <vedavinayagam.ganesan@nokia.com>
Changes for setting platfrom specific lag id boundary id in the chassis
app db. The platfrom specific lag id boundaries are supplied via
chassisdb.conf. The lag_id_start and lag_id_end boundary values sourced
from this file are set in chassis app db which will be used by lag id
allocator to allocate unique lag id in atomic fashion
- Why I did it
I made the docker_img_ctl.j2 applicable for more dockers (including application extensions dockers) by adding an option not to mount tmpfs on /tmp/ and /var/tmp/. In some applications /tmp/ is a different docker volume which can't be tmpfs.
Also, I added and ability to pass REPO[:TAG]|[@digest]/IMAGE_ID instead of just REPO name.
- How I did it
Modified docker_img_ctl.j2 and docker makefiles.
- How to verify it
Run it on the switch.
- Why I did it
To allow SONiC Package Migration during SONiC-2-SONiC upgrade we need to start docker daemon in chroot-ed environment in new SONiC filesystem.
Later this script will be used to start dockerd in chroot environment on SONiC
- How I did it
Install a docker service script into /usr/lib/docker/ in SONiC filesystem.
- How to verify it
Install SONiC image on the switch, mount squashfs to some directory, mount overlay rw layer over squashfs, mount procfs and sysfs, mount docker library. Start the docker using:
root@sonic:~$ /usr/lib/docker/docker.sh start
Signed-off-by: Stepan Blyshchak <stepanb@nvidia.com>
Features may be enabled/disabled for the same topology based on run-time
configuration. This PR adds the ability to enable/disable feature based
on config db data.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
Why I did it
We skip install of CNI plugin, as we don't need. But this leaves node in "not ready" state, upon joining master.
To fix, we copy this dummy .conf file in /etc/cni/net.d
How I did it
Keep this file in /usr/share/sonic/templates and copy to /etc/cni/net.d upon joining k8s master.
How to verify it
Upon configuring master-IP and enable join, watch node join and move to ready state.
You may verify using kubectl get nodes command
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
In the configuration of rsyslog, duplicate messages will be suppressed and reported in the format of message repeated n times.
Due to this behavior, if a critical process in a container exited unexpectedly, the alerting message will be written into syslog once
and not be written into syslog anymore until the second critical process exited. This PR aims to differentiate these alerting messages such that they will not be suppressed by rsyslogd and can appear in the syslog periodically.
How I did it
This PR adds a counter into the alerting message and shows how many minutes a critical process was not running.
How to verify it
I verified and test this implementation on a physical DUT.
SONiC Package Manager will require to auto-generate the start script using that template. For that, we need this template to be recorded in SONiC filesystem.
Signed-off-by: Stepan Blyshchak <stepanb@nvidia.com>
- Why I did it
Group all SONiC services together and able to manage them together. Will be used in config reload command as much simpler and generic way to restart services.
- How I did it
Add services to sonic.target
- How to verify it
Together with Azure/sonic-utilities#1199
config reload -y
Signed-off-by: Stepan Blyshchak <stepanb@nvidia.com>
show ip interfaces is enhanced recently to support multi ASIC platforms in this PR- https://github.com/Azure/sonic-utilities/pull/1396 .
The ipintutil script as to run as sudo user, to get the ip interface from each namespace.
Add this script to the sudoer file so that show ip interface command is available for user with read-only permissions
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
- Why I did it
The pcie configuration file location is under plugin directory not under platform directory.
#6437
- How I did it
Move all pcie.yaml configuration file from plugin to platform directory.
Remove unnecessary timer to start pcie-check.service
Move pcie-check.service to sonic-host-services
- How to verify it
Verify on the device
- Add support for `DCS-7050SX3-48YC8` and `DCS-7050SX3-48C8` platform
- Add support for more variants of `DCS-7280CR3-32[PD]4`
- Add Supervisor to Linecard consutil support
- Complete Watchdog platform API support
- Fix some PSU behavior on `DCS-7050QX-32` and `DCS-7060CX-32S`
- Fix SEU management on `DCS-7060CX-32S`
- Allow kernel modules to build up to linux 5.10
- Rename led color `orange` to `amber`
- Miscellaneous fixes
Update topology script to retrieve hwsku from minigraph
if hwsku information is not available in config_db.
Fix clean up of interfaces in msft_multi_asic_vs hwsku
topology script.
- Why I did it
When bringing up multi-asic VS switch, topology service is started during boot up.
Topology service starts a shell script which runs the topology script present in /usr/share/sonic/device// directory. To invoke hwsku specific script, the topology script tries to retrieve hwsku information from config_db.
During initial boot up config_db might not be populated. In order to start topology service before config_db is updated,
update topology script to get hwsku information from minigraph.xml if it is available.
This will be helpful to bring up multi-asic VS testbed by loading minigraph and starting topology service.
- How I did it
Update topology.sh script to retrieve hwsku information from minigraph.xml.
Fix clean up function on msft_multi_asic_vs toplogy script.
- How to verify it
single-asic VS - no change; topology service is only enabled for multi-asic VS.
multi-asic VS - Bring up multi-asic VS image, copy minigraph to vs image, start topology service. Topology service should be successful.
to test clean up function fix, start topology service - make sure interfaces are created and moved to the right namespaces.
stop topology service - make sure namespace do not have any interface and all front end interfaces are present in default namespace.
- What I did
All SWSS dependent services should stop before SWSS service to avoid future possible issues.
For example 'teamd' service will stop before to allow the driver unload netdev gracefully.
This is to stop all LAG's before restarting syncd service when running 'config reload' command.
- How I did it
Change the order of dependent services of SWSS.
- How to verify it
Run 'config reload' command.
Previously the operation failed when a large number of PortChannel configured on the system.
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
* Add *MUX_CABLE_TABLE* to set of tables to clear on SWSS start, which
will clear HW_MUX_CABLE_TABLE and MUX_CABLE_TABLE
* Order swss to start before pmon to ensure that DBs are cleared before
xcvrd (running inside pmon) starts and re-populates the tables
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
Fix marvell-armhf build break
The azure-storage package depends on the cryptography package. Newer
versions of cryptography require the rust compiler, the correct version
for which is not readily available in buster. Hence we pre-install an
older version here to satisfy the azure-storage dependency.
Note: This is not a problem for other architectures as pre-built versions
of cryptography are available for those. This sequence can be removed
after upgrading to debian bullseye.
**- Why I did it**
To support FW upgrade on init.
**- How I did it**
Change timeout value
**- How to verify it**
I manually changed ASIC and Gearbox FW followed by hard reset in order for FW upgrade to take place on init.
Signed-off-by: liora <liora@nvidia.com>
- Why I did it
To move ‘sonic-host-service’ which is currently built as a separate package to ‘sonic-host-services' package.
- How I did it
- Moved 'sonic-host-server' to 'src/sonic-host-services' and included it as part of the python3 wheel.
- Other files were moved to 'src/sonic-host-services-data' and included as part of the deb package.
- Changed build option ‘INCLUDE_HOST_SERVICE’ to ‘ENABLE_HOST_SERVICE_ON_START’ for enabling sonic-hostservice at boot-up by default.
[multi_asic][vs]: Add dependency in teamd service to start after topology service.
- Why I did it
In multi-asic VS, topology service is run after database service to set up the internal asic topology.
swss and syncd have a dependency to start after topology service is run so that the interfaces are moved to right namespace and created in the right namespace. In case of multi-asic vs, during the initial boot up, when there is no configuration added, teamd service starts and swss/syncd do not start as topology service does not start. Upon loading configuration using config_db or minigraph, swss and sycnd start up , but teamd is not restarted as swss is not stopped and started. This causes teamd to be in a bad state and requires a reload of config.
- How I did it
Add dependency in teamd service to start after topology service is completed.
- How to verify it
No change in single asic vs or platform.
No change in multi-asic regular image.
Change only in multi-asic VS. Bring up a multi-asic VS image without any configration, teamd service will fail to start due to dependency failure. Load minigraph, start topology service, load configuration, ensure all services come up.
Signed-off-by: SuvarnaMeenakshi <sumeenak@microsoft.com>
- Why I did it
As of Azure/sonic-utilities#1297, subcommands of pcieutil have changed to remove the redundant pcie- prefix. This PR adapts calling applications (pcie-check) to the new syntax.
Resolves#6676
- How I did it
Remove pcie- prefix from pcieutil subcommands in calling applications
Also add pcieutil * to sudoers file, as pcieutil requires elevated permissions
A few issues where discovered with crashkernel on Arista platforms.
1) platforms using `docker_inram=on` would end up OOM in kdump environment.
This happens because the same initramfs is used by SONiC and the crashkernel.
With `docker_inram=on` the `dockerfs.tar.gz` is extracted in a `tmpfs` created for the occasion.
Since `dockerfs.tar.gz` weights more than 1.5G, it doesn't fit into the kdump environment and ends up OOM.
This OOM event can in turn trigger a panic.
2) Arista platforms with `secureboot` enabled would fail to load the crashkernel because the kernel parameter would be discarded on boot.
This happens because the `boot0` in secureboot mode is strict about kernel parameter injection.
3) The secureboot path allowlist would remove kernel crash reports.
4) The kdump service would fail on Arista products since `/boot/` is empty in `secureboot`
**- How I did it**
1) To prevent an OOM event in the crashkernel the fix is to avoid the codepaths in `union-mount` that create tmpfs and populate them. Some more codepath specific to Arista devices are also skipped to make the kdump process faster.
This relies on detecting that the initramfs is starting in a kdump environment and skipping some initialization.
The `/usr/sbin/kdump-config` tool appends a few kernel cmdline arguments when loading the crashkernel.
The most unique one is `systemd.unit=kdump-tools.service` which is used in a few initramfs hooks to set `in_kdump`.
2) To allow `kdump` to work in `secureboot` environment the cmdline generation in boot0 was slightly modified.
The codepath to load kernel parameters changed by SONiC is now running for booting in secure mode.
It was altered to prevent an append only behavior which would grow the `kernel-cmdline` at every reboot.
This ever growing behavior would lead `kexec` to fail to load the kernel due to a too long cmdline.
3) To get the kernel crash under /var/crash this path has to be added to `allowlist_paths`
4) The `/host/image-XXX/boot` folder is now populated in `secureboot` mode but not used.
**- How to verify it**
Regular boot:
- enable kdump
- enable docker_inram=on via kernel-params
- reboot
- generate a crash `echo c > /proc/sysrq-trigger`
- before: witness OOM events on the console
- after: crash kernel works and crash available under /var/crash
Secure boot:
- enable kdump
- reboot
- generate a crash `echo c > /proc/sysrq-trigger`
- before: witness no kdump
- after: crash kernel works and crash available under /var/crash
Co-authored-by: Boyang Yu <byu@arista.com>
fixesAzure/sonic-utilities#1389
With the recent changes in sudoer files. The show commands fails for the read-only users.
The problem here is the 'docker ps' is failing in the function [get_routing_stack()](8a1109ed30/show/main.py (L54)) therefore all the CLI commands are failing.
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
- Why I did it
The command sudo ip netns identify <pid> is used in function get_current_namespace
to check in the cli command is running in host context or within a namespace.
This function is used for every CLI command and command sudo ip netns identify <pid> needs to be added in sudoer files to allow users with RO access to run show cli commands
This problem is not there on single asic platforms.
- How I did it
Add ip netns identify [0-9]* to sudoers file.
Following changes were done for ebtables:
- Support for Multi-asic platforms. Ebtable filters are installed in namespace for multi-asic and not host. On Single asic installed on host.
- For Multi-asic platforms we don't want to install on host otherwise Namespace-to-Namespace communication does not happens since ARP Request are not forwarded.
- Updated to use text file to restore ebtables rules then the binary format. Rules are restore as part of Database docker init instead of rc.local
- Removed the ebtable service files for buster as not needed as filters are restored/installed as part of database docker init.
All the binaries are pre-installed with ebtables* binary are same as ebatbles-legacy-*
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
The Portchannels were not getting cleaned up as the cleanup activity was taking more than 10 secs which is default docker timeout after which a SIGKILL will be send.
Fixes#6199
To check if it works out for this issue in 201911 ? #6503
This issue is significantly seen in master branch compared to 201911 because the Portchannel cleanup takes more time in master. Test on a DUT with 8 Port Channels.
master
admin@str-s6000-acs-8:~$ time sudo systemctl stop teamd
real 0m15.599s
user 0m0.061s
sys 0m0.038s
Sonic 201911.v58
admin@str-s6000-acs-8:~$ time sudo systemctl stop teamd
real 0m5.541s
user 0m0.020s
sys 0m0.028s
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan arlakshm@microsoft.com
- Why I did it
This PR has the changes to support having different swss.rec and sairedis.rec for each asic.
The logrotate script is updated as well
- How I did it
Update the orchagent.sh script to use the logfile name options in these PRs(Azure/sonic-swss#1546 and Azure/sonic-sairedis#747)
In multi asic platforms the record files will be different for each asic, with the format swss.asic{x}.rec and sairedis.asic{x}.rec
Update the logrotate script for multiasic platform .
- Why I did it
Initially, we used Monit to monitor critical processes in each container. If one of critical processes was not running
or crashed due to some reasons, then Monit will write an alerting message into syslog periodically. If we add a new process
in a container, the corresponding Monti configuration file will also need to update. It is a little hard for maintenance.
Currently we employed event listener of Supervisod to do this monitoring. Since processes in each container are managed by
Supervisord, we can only focus on the logic of monitoring.
- How I did it
We borrowed the event listener of Supervisord to monitor critical processes in containers. The event listener will take
following steps if it was notified one of critical processes exited unexpectedly:
The event listener will first check whether the auto-restart mechanism was enabled for this container or not. If auto-restart mechanism was enabled, event listener will kill the Supervisord process, which should cause the container to exit and subsequently get restarted.
If auto-restart mechanism was not enabled for this contianer, the event listener will enter a loop which will first sleep 1 minute and then check whether the process is running. If yes, the event listener exits. If no, an alerting message will be written into syslog.
- How to verify it
First, we need checked whether the auto-restart mechanism of a container was enabled or not by running the command show feature status. If enabled, one critical process should be selected and killed manually, then we need check whether the container will be restarted or not.
Second, we can disable the auto-restart mechanism if it was enabled at step 1 by running the commnad sudo config feature autorestart <container_name> disabled. Then one critical process should be selected and killed. After that, we will see the alerting message which will appear in the syslog every 1 minute.
- Which release branch to backport (provide reason below if selected)
201811
201911
[x ] 202006
