Co-authored-by: Zhi Yuan (Carl) Zhao <zyzhao@arista.com>
Why I did it
Arista 7060 platform has a rare and unreproduceable PCIe timeout that could possibly be solved with increasing the switch PCIe timeout value. To do this we'll call a script for this platform to increase the PCIe timeout on boot-up.
No issues would be expected from the setpci command. From the PCIe spec:
"Software is permitted to change the value in this field at any
time. For Requests already pending when the Completion
Timeout Value is changed, hardware is permitted to use either
the new or the old value for the outstanding Requests, and is
permitted to base the start time for each Request either on when
this value was changed or on when each request was issued. "
How I did it
Add "platform-init" support in swss docker similar to how "hwsku-init" is called, only this would be for any device belonging to a platform. Then the script would reside in device data folder.
Additionally, add pciutils dependency to docker-orchagent so it can run the setpci commands.
How to verify it
On bootup of an Arista 7060, can execute:
lspci -vv -s 01:00.0 | grep -i "devctl2"
In order to check that the timeout has changed.
- Create a script in the orchagent docker container which listens for these encapsulated packets which are trapped to CPU (indicating that they cannot be routed/no neighbor info exists for the inner packet). When such a packet is received, the script will issue a ping command to the packet's inner destination IP to start the neighbor learning process.
- This script is also resilient to portchannel status changes (i.e. interface going up or down). An interface going down does not affect traffic sniffing on interfaces which are still up. When an interface comes back up, we restart the sniffer to start capturing traffic on that interface again.
**- Why I did it**
As part of migrating SONiC codebase from Python 2 to Python 3
**- How I did it**
- No longer install Python 2 in docker-base-buster or docker-config-engine-buster.
- Install Python 2 and pip2 in the following containers until we can completely eliminate it there:
- docker-platform-monitor
- docker-sonic-mgmt-framework
- docker-sonic-vs
- Pin pip2 version <21 where it is still temporarily needed, as pip version 21 will drop support for Python 2
- Also preform some other cleanup, ensuring that pip3, setuptools and wheel packages are installed in docker-base-buster, and then removing any attempts to re-install them in derived containers
Install the necessary python3 dependent packages to convert restore_neighbor.py
to support python3 as python2 is EOL. See: Azure/sonic-swss#1542
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
**- Why I did it**
To support dynamic buffer calculation.
This PR also depends on the following PRs for sub modules
- [sonic-swss: [buffermgr/bufferorch] Support dynamic buffer calculation #1338](https://github.com/Azure/sonic-swss/pull/1338)
- [sonic-swss-common: Dynamic buffer calculation #361](https://github.com/Azure/sonic-swss-common/pull/361)
- [sonic-utilities: Support dynamic buffer calculation #973](https://github.com/Azure/sonic-utilities/pull/973)
**- How I did it**
1. Introduce field `buffer_model` in `DEVICE_METADATA|localhost` to represent which buffer model is running in the system currently:
- `dynamic` for the dynamic buffer calculation model
- `traditional` for the traditional model in which the `pg_profile_lookup.ini` is used
2. Add the tables required for the feature:
- ASIC_TABLE in platform/\<vendor\>/asic_table.j2
- PERIPHERAL_TABLE in platform/\<vendor\>/peripheral_table.j2
- PORT_PERIPHERAL_TABLE on a per-platform basis in device/\<vendor\>/\<platform\>/port_peripheral_config.j2 for each platform with gearbox installed.
- DEFAULT_LOSSLESS_BUFFER_PARAMETER and LOSSLESS_TRAFFIC_PATTERN in files/build_templates/buffers_config.j2
- Add lossless PGs (3-4) for each port in files/build_templates/buffers_config.j2
3. Copy the newly introduced j2 files into the image and rendering them when the system starts
4. Update the CLI options for buffermgrd so that it can start with dynamic mode
5. Fetches the ASIC vendor name in orchagent:
- fetch the vendor name when creates the docker and pass it as a docker environment variable
- `buffermgrd` can use this passed-in variable
6. Clear buffer related tables from STATE_DB when swss docker starts
7. Update the src/sonic-config-engine/tests/sample_output/buffers-dell6100.json according to the buffer_config.j2
8. Remove buffer pool sizes for ingress pools and egress_lossy_pool
Update the buffer settings for dynamic buffer calculation
As part of the transition from Python 2 to Python 3, we are installing both pip2 and pip3 in the slave and config-engine containers. This PR replaces calls to `pip` in these containers with an explicit call to `pip2` to ensure the proper version of pip is executed, no matter which version of pip is aliased to `pip`, as we no longer rely on that alias.
Also some other pip-related cleanup
* Install ndppd during image build, and copy config files to image
* Configure proxy settings based on config DB at container start
* Pipe ndppd output to logger inside container to log output in syslog
This PR limited the number of calls to sonic-cfggen to one call
per iteration instead of current 3 calls per iteration.
The PR also installs jq on host for future scripts if needed.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
also update submodule
* 01f810f 2020-07-02 | fix compiling issue for gcc8.3 (#1339) [lguohan]
* 9b13120 2020-07-03 | Fix in script to avoid orchagent crash when port down followed by fdb delete (#1340) [rupesh-k]
* 9b01844 2020-07-01 | [qosorch] Update QoS scheduler params for shaping features (#1296) [Michael Li]
* 86b5e99 2020-07-02 | [mirrororch] Port Mirroring implementation (#1314) [rupesh-k]
* c05601c 2020-06-24 | [portsyncd]: add debug message if a port cannot be found in port able (#1328) [lguohan]
* a0b6412 2020-06-23 | COPP_DEL_fix: DEL for one trap group from SONIC is resetting all the trap IDs (#1273) [SinghMinu]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
libpython2.7, libdaemon0, libdbus-1-3, libjansson4 are common
across different containers. move them into docker-base-stretch
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* Changes in sonic-buildimage for the NAT feature
- Docker for NAT
- installing the required tools iptables and conntrack for nat
Signed-off-by: kiran.kella@broadcom.com
* Add redis-tools dependencies in the docker nat compilation
* Addressed review comments
* add natsyncd to warm-boot finalizer list
* addressed review comments
* using swsscommon.DBConnector instead of swsssdk.SonicV2Connector
* Enable NAT application in docker-sonic-vs
Put a flag for fast-reboot to the db using EXPIRE feature. Using this flag in other part of SONiC to start in Fast-reboot mode. If we reload a config, the state in the db will be removed.
ARM Architecture support in SONIC
make configure platform=[ASIC_VENDOR_ARCH] PLATFORM_ARCH=[ARM_ARCH]
SONIC_ARCH: default amd64
armhf - arm32bit
arm64 - arm64bit
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
- create a dockerfile-marcros.j2 file with all common operations
written as j2 macro
- use single dockerfile instruction for COPY and RUN commands
when possible to improve build time
- reorganize dockerfile instructions to make more cache friendly
(in case someday we will remove --no-cache to build docker images)
Signed-off-by: Stepan Blyschak <stepanb@mellanox.com>
* [service] Restart SwSS Docker container if orchagent exits unexpectedly
* Configure systemd to stop restarting swss if it attempts to restart more than 3 times in 20 minutes
* Move supervisor-proc-exit-listener script
* [docker-dhcp-relay] Enhance wait_for_intf.sh.j2 to utilize STATEDB
* Ensure dependent services stop/start/restart with SwSS
* Change 'StartLimitInterval' to 'StartLimitIntervalSec', as Stretch installs systemd 232 (>= v230)
* Also update journald.conf options
* Remove 'PartOf' option from unit files
* Add '$(SUPERVISOR_PROC_EXIT_LISTENER_SCRIPT)' to new shared docker-orchagent makefile
* Make supervisor-proc-exit-listener script read from 'critical_processes' file inside container
* Update critical_processes file for swss container
* Restore neighbor table to kernel during system warm-reboot
Added a service: "restore_neighbors" to restore neighbor table into
kernel during system warm reboot. The service is started by supervisord
in swss docker when the docker is started.
In case system warm reboot is enabled, it will try to restore the neighbor
table from appDB into kernel through netlink API calls and update the neighbor
table by sending arp/ns requests to all neighbor entries, then it sets the
stateDB flag for neighsyncd to continue the reconciliation process.
-- Added tcpdump python-scapy debian package into orchagent and vs dockers.
-- Added python module: pyroute2 netifaces into orchagent and vc dockers.
-- Workarounded tcpdump issue in the vs docker
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
* Move the restore_neighbors.py to sonic-swss submodule
Made changes to makefiles accordingly
Make dockerfile.j2 changes and supervisord config changes
Add python monotonic lib for time access
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
* Added PYTHON_SWSSCOMMON as swss runtime dependency
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
Previously use / to separate container name and program name.
However, in rsyslogd:
Precisely, the programname is terminated by either (whichever occurs first):
end of tag
nonprintable character
‘:’
‘[‘
‘/’
The above definition has been taken from the FreeBSD syslogd sources.
Signed-off-by: Guohan Lu <gulv@microsoft.com>
* Fix potential blackholing/looping traffic and refresh ipv6 neighbor to avoid CPU hit
In case ipv6 global addresses were configured on L3 interfaces and used for peering,
and routing protocol was using link-local addresses on the same interfaces as prefered nexthops,
the link-local addresses could be aged out after a while due to no activities towards the link-local
addresses themselves. And when we receive new routes with the link-local nexthops, SONiC won't insert
them to the HW, and thus cause looping or blackholing traffic.
Global ipv6 addresses on L3 interfaces between switches are refreshed by BGP keeplive and other messages.
On server facing side, traffic may hit fowarding plane only, and no refresh for the ipv6 neighbor entries regularly.
This could age-out the linux kernel ipv6 neighbor entries, and HW neighbor table entries could be removed,
and thus traffic going to those neighbors would hit CPU, and cause traffic drop and temperary CPU high load.
Also, if link-local addresses were not learned, we may not get them at all later.
It is intended to fix all above issues.
Changes:
Add ndisc6 package in swss docker and use it for ipv6 ndp ping to update the neighbors' state on Vlan interfaces
Change the default ipv6 neighbor reachable timer to 30mins
Add periodical ipv6 multicast ping to ff02::11 to get/refresh link-local neighbor info.
* Fix review comments:
Add PORTCHANNEL_INTERFACE interface for ipv6 multicast ping
format issue
* Combine regular L3 interface and portchannel interface for looping
* Add ndisc6 package to vs docker
Set the ECMP/LAG hash seed to 10 when the switch is a ToR, 20 when the switch
is a Leaf, 0 otherwise.
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
This field contains all neighbor devices information using the device
hostname as the key and having lo_addr, mgmt_addr, hwsku, type as the
attributes.
Move the file msn27xx.32ports.buffers.json.j2 from sonic-swss repository to
this repository so that we could add unit test for this file.
Unit test is added for platform ACS-MSN2700.
Signed-off-by: Shu0T1an ChenG <shuche@microsoft.com>
- Consolidate config.sh and start.sh scripts into one script (start.sh)
- Solve issue #435 - All dockers now run supervisord as their ENTRYPOINT
- All stdout/stderr output from processes managed by supervisord is now sent to syslog instead of their own files
- Supervisord log messages are now also sent to syslog
- Removed unused smartmontools package from docker-platform-monitor
[swss]: Generate config files for Everflow and IPinIP from minigraph
- Add Everflow DST IP to minigraph file
- Extend minigraph.py to support Everflow
- Add templates file for Everflow and IPinIP configuration
- Add config.sh for swss docker to generate config files
The reason is that /etc/network/interfaces file is in base image. After booting,
docker-swss is not ready and thus the empty VLAN interfaces cannot be created
when the brctl is pointing to the binary inside the swss docker.
Add the bridge-utils into the base image and add bridge_ports none to the
/etc/network/interfaces file so that after boot-up the empty VLAN interfaces
will be created to let the members to join later.
Signed-off-by: Shuotian Cheng <shuche@microsoft.com>
* [docker-config-engine]: introduce docker sonic config engine
sonic config engine provide the sonic configure engine for all sonic
dockers that rely on the engine to generate runtime configuration.
