**- Why I did it**
sonic-utilities will become dependent upon sonic-platform-common as of https://github.com/Azure/sonic-utilities/pull/1386.
**- How I did it**
- Add sonic-platform-common as a dependency in docker-sonic-vs.mk
- Additionally, no longer install Python 2 packages of swsssdk and sonic-py-common, as they should no longer be needed.
Changes in the new release:
1. Policy based hashing optimization
2. New attribute support for Max port headroom
3. Tunnel ECN map fixes
4. Tunnel EVPN skeleton extensions (peer attrib, maps)
5. Bridge port admin not affecting port admin (optimize port down time)
6. CRM new API for neighbors and tunnel termination entries
7. Improve FDB event for flush by bridge port (before, null bridge was reported to SONiC, now the bridge will be extracted from bridge port)
8. DHCP L2 v4+v6 traps (for ZTP use case)
9. Generic counter implementation
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- combine docker-ptf-saithrift into docker-ptf docker
- build docker-ptf under platform vs
- remove docker-ptf for other platforms
Signed-off-by: Guohan Lu <lguohan@gmail.com>
During ISSU, "mlxsw_minimal" driver still trying to access firmware, in some cases FW could return some wrong critical threshold value which will cause switch shutdown.
**- How I did it**
In order to prevent "mlxsw_minimal" driver from accessing ASIC during ISSU, SDK will raise "OFFLINE" 'udev' event
at the early beginning of such flow. When this event is received, hw-management will remove "mlxsw_minimal" driver.
There is no need to implement the opposite "ONLINE" event since this flow is ended up with "kexec".
**- How to verify it**
repeatedly perform warm reboot, make sure there is no switch shutdown occurred.
Bugs fixes:
All | Kernel | During system reload when CPU is loaded with heavy traffic, a Kernel Panic may occur.
All | Modules, Port split | FW stuck when device rebooted with locked Optical Transceivers in split mode
Spectrum-3 | PFC | On Spectrum-3 systems, slow reaction time to Rx pause packets on 40GbE ports may lead to buffer overflow on servers.
Spectrum-3 | SN4700, Port Split | On rare occasion SN4700, conducting 100G split (4x25G) in NRZ when splitter port 1 or 2 are down, ports 3 and 4 will also go down.
Enahncments:
All | Kernel | new notification on ISSU start, so other kernel drivers can disable any interface to ASIC
Signed-off-by: Kebo Liu <kebol@nvidia.com>
Check #6483
add test to make sure default route change in eth0 does not
affect the default route in the default vrf
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Fixes#6445
Because the ipmihelper.py script in the 9332 folder is slightly different than the common one (due to LGTM fixes), when the common one gets copied during build time it causes the workspace/build to become dirty.
Signed-off-by: Danny Allen <daall@microsoft.com>
- Why I did it
Initially, we used Monit to monitor critical processes in each container. If one of critical processes was not running
or crashed due to some reasons, then Monit will write an alerting message into syslog periodically. If we add a new process
in a container, the corresponding Monti configuration file will also need to update. It is a little hard for maintenance.
Currently we employed event listener of Supervisod to do this monitoring. Since processes in each container are managed by
Supervisord, we can only focus on the logic of monitoring.
- How I did it
We borrowed the event listener of Supervisord to monitor critical processes in containers. The event listener will take
following steps if it was notified one of critical processes exited unexpectedly:
The event listener will first check whether the auto-restart mechanism was enabled for this container or not. If auto-restart mechanism was enabled, event listener will kill the Supervisord process, which should cause the container to exit and subsequently get restarted.
If auto-restart mechanism was not enabled for this contianer, the event listener will enter a loop which will first sleep 1 minute and then check whether the process is running. If yes, the event listener exits. If no, an alerting message will be written into syslog.
- How to verify it
First, we need checked whether the auto-restart mechanism of a container was enabled or not by running the command show feature status. If enabled, one critical process should be selected and killed manually, then we need check whether the container will be restarted or not.
Second, we can disable the auto-restart mechanism if it was enabled at step 1 by running the commnad sudo config feature autorestart <container_name> disabled. Then one critical process should be selected and killed. After that, we will see the alerting message which will appear in the syslog every 1 minute.
- Which release branch to backport (provide reason below if selected)
201811
201911
[x ] 202006
**- Why I did it**
On the Mellanox platform, reboot cause is fetched from some certain sysfs which is created by the hw-management service. So determine-reboot-cause service shall start after hw-management, otherwise it could fail due to the related sysfs is not available yet.
**- How I did it**
Add a patch to the hw-management service to make sure determine-reboot-cause service should start after it.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
**- Why I did it**
- The thermalctld daemon on the Pmon docker requires support from the thermal manager API.
**- How I did it**
- Removed the old function for detecting a faulty fan.
- Removed the old function for detecting excess temperature.
- Implement thermal_manager APIs based on ThermalManagerBase
- Implement thermal_conditions APIs based on ThermalPolicyConditionBase
- Implement thermal_actions APIs based on ThermalPolicyActionBase
- Implement thermal_info APIs based on ThermalPolicyInfoBase
- Add thermal_policy.json
It's been reported that accton fan monitor process keeps consuming memory after few days.
The amount of memory occupied increases in linear and never leased.
Signed-off-by: roy_lee <roy_lee@edge-core.com>
1. Fixes the missing DPKG file for gbsyncd-vs package
2. Fixes the softlink issue on the Platform-common and ztp package
3. Fixes the PYTHNON_DEBS list is missing for DBG dockers.
- Improve random number generation during early Sonic initialization by providing SW updates to Linux entropy value.
- Improve handling of platform In-Band management port
This commit provides the following updates to the Nokia ixs7215 platform
1. The Marvell Armada-38x SOC requires SW assistance to improve the system
entropy value available early on in the Sonic boot sequence.
2. The Nokia ixs7215 platform does not have a dedicated Out-Of-Band (OOB) mgmt
port and thus requires additional logic to optionally support configuring
front panel port 48 as an In-Band mgmt port. This commit provides additional
logic to manage and maintain the operation of this In-Band mgmt port.
fix platform driver breakage due to python3 upgrade and fix load minigraph errors with config load_minigraph -y
**- How I did it**
added python3-smbus to the pmon docker template since the previous was python2 specific
fixed additional "ord" python2 specific code
fixed the jinja templates used by qos reload - the template logic required data to be parsed
**- How to verify it**
run "show platform XXX" commands and verify output
run "sudo config load_minigraph -y" and verify configuration
run "show interfaces XXX" and verify output
Co-authored-by: Carl Keene <keene@nokia.com>
Centec syncd have beend upgraded to buster, docker-syncd-centec-rpc do not need generate stretch based docker.
Co-authored-by: Xianghong Gu <xgu@centecnetworks.com>
In rare case can see that xcvrd failed due to "UnboundLocalError: local variable 'label_port' referenced before assignment"
Init "label_port" as None at the beginning of the function, to avoid the case that "label_port" not assigned.
Fix#119
when parallel build is enable, multiple dpkg-buildpackage
instances are running at the same time. /var/lib/dpkg is shared
by all instances and the /var/lib/dpkg/updates could be corrupted
and cause the build failure.
the fix is to use overlay fs to mount separate /var/lib/dpkg
for each dpkg-buildpackage instance so that they are not affecting
each other.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
* Enable telemetry for ARM64 by default
* [Centec]Upgrade Centec syncd docker to buster; libjemalloc2 have been installed in docker-base-buster, remove libjemalloc1 from docker-syncd-centec's Dockerfile.j2
Co-authored-by: Gu Xianghong <xgu@centecnetworks.com>
- Make PDDF code compliant with both Python 2 and Python 3
- Align code with PEP8 standards using autopep8
- Build and install both Python 2 and Python 3 PDDF packages
Starting from build (master) 176 the warm reboot on BRCM Platform started to experience syncd crash. Upon further debug by Ying it was determined that the crash was related to the following new change:
[Dynamic buffer calc] Support dynamic buffer calculation (#1338)
Ying also debugged further and found The crash was caused by buffer pool profile setting operation SAI_BUFFER_PROFILE_ATTR_SHARED_DYNAMIC_TH
A case has filed with BRCM while a potential fix was tried by Ying that seems to have addressed this issue and we are making this change available in master branch so that it will allow further feature validation/testing especially in the warm reboot area.
Once an official fix is provided by BRCM, we will then remove this in house fix and apply the official fix.
- How to verify it
Just perform warm reboot with any master code 175 or above you should see this issue or issue the following cmd will also cause the crash: "mmuconfig -p egress_lossy_profile -a 0"
- Dynamically change EEPROM driver based on media type.
- Otherwise, EEPROM INFO and DOM INFO might not be fetched properly and will result in erroneous output.
combine multiple same operation into one operation to reduce
the build steps. this is to avoid max depth exceeded issue
in the build.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Add a systemd dependency to make platform-modules service as a prerequisite for determine-reboot-cause service to ensure platform initialization is complete before determine-reboot-cause.service executes.
the control file version is 4.2.1.5-7
sonic$ sudo dpkg -i target/debs/buster/libsaibcm-dev_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm-dev_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm-dev (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm-dev (4.2.1.5-7) ...
lgh@491d842369cf:/sonic$ sudo dpkg -i target/debs/buster/libsaibcm_4.2.1.5-8_amd64.deb
(Reading database ... 175880 files and directories currently installed.)
Preparing to unpack .../libsaibcm_4.2.1.5-8_amd64.deb ...
Unpacking libsaibcm (4.2.1.5-7) over (4.2.1.5-7) ...
Setting up libsaibcm (4.2.1.5-7) ...
Processing triggers for libc-bin (2.28-10) ...
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Accton util applies lsmod to check if drivers are installed.
But lsmod may return error on startup and skip module installation.
Signed-off-by: Brandon Chuang <brandon_chuang@edge-core.com>
Features:
Spectrum-3 | Systems | Added GA-level support for SN4700 A0 system
All | Shared headroom | Added GA-level support for Shared headroom between PGs
Bugs fixes:
All | Counters | Sent traffic in certain size is wrongly increase to a smaller size counter, because port extended counter has a counter for sent traffic per packet-size range
All | Shared buffer | Configuring shared buffer on the fly may, on occasion, cause the chip to get stuck
Spectrum-2 | Modules | On occasion, link down is experienced with INPHI COLORZ PAM4 100G optic cables on SN3700 systems
- Why I did it
Make EEPROM platform APIs Python3 compliant in Nokia platform.
- How I did it
Handle bytearray type returned by read_eeprom and read_eeprom_bytes methods.
- How to verify it
Boot Nokia ixs7215 and verify PMON docker running and show platform syseeprom
Co-authored-by: Carl Keene <keene@nokia.com>
Introduce tunnel manager daemon. Start the process as part of swss container
Submodule update for swss:
9ed3026 - 2020-12-24 : [NAT] ACL Rule with DO_NOT_NAT action is getting failed. (#1502) [Akhilesh Samineni]
c39a4b1 - 2020-12-23 : Mux/IPTunnel orchagent changes (#1497) [Prince Sunny]
bc8df0e - 2020-12-23 : Add support for headroom pool watermark (#1567) [Neetha John]
**- Why I did it**
As part of migrating SONiC codebase from Python 2 to Python 3
**- How I did it**
- No longer install Python 2 in docker-base-buster or docker-config-engine-buster.
- Install Python 2 and pip2 in the following containers until we can completely eliminate it there:
- docker-platform-monitor
- docker-sonic-mgmt-framework
- docker-sonic-vs
- Pin pip2 version <21 where it is still temporarily needed, as pip version 21 will drop support for Python 2
- Also preform some other cleanup, ensuring that pip3, setuptools and wheel packages are installed in docker-base-buster, and then removing any attempts to re-install them in derived containers
