Why I did it
The docker storage driver vfs is not a good option for build, it uses the “deep copy” when building a new layer, leads to lower performance and more space used on disk than other storage drivers.
A better docker storage driver is the default one overlay2, it is a modern union filesystem.
- Why I did it
Recent change to delay PMON service in case of fast/warm reboot introduce an issue when restarting only SWSS service after fast/warm reboot for Nvidia platform.
Since the timer is triggered only when the system boot, in a scenario when the system is after a fast/warm reboot and the user restart SWSS service, as part of syncd.sh script, PMON service will stop but the timer will not start again.
- How I did it
On syncd.sh script, in case of fast/warm indication, check if pmon.timer is running.
If it is running it means we are at the first boot and continue normally.
If it is not running, meaning the service was restarted, start the timer to keep the system behavior consistent.
- How to verify it
Run fast/warm reboot.
service swss restart.
Observe PMON service starting.
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
Why I did it
Recently the nightly testing pipeline found that the autorestart test case was failed when it was run against master image. The reason is Restart= field in each container's systemd configuration file was set to Restart=no even the value of auto_restart field in FEATURE table of CONFIG_DB is enabled.
This issue introduced by #10168 can be reproduced by the following steps:
Issues the config command to disable the auto-restart feature of a container
Runs command config reload or config reload minigraph to enable auto-restart of the container
Checks Restart= field in the container's systemd config file mentioned in step 1 by running the command
sudo systemctl cat <container_name>.service
Initially this PR (#10168) wants to revert the changes proposed by this: #8861. However, it did not fully revert all the changes.
How I did it
When hostcfgd started or was restarted, the Restart= field in each container's systemd configuration file should be initialized according to the value of auto_restart field in FEATURE table of CONFIG_DB.
How to verify it
I verified this change by running auto-restart test case against newly built master image and also ran the unittest:
The following commits are pushed
1f112b8 (HEAD -> 202205, origin/202205) [sonic-ycabled] fix grpc logic for timeout,cli HWSTATUS value retrival logic for active-active cable (#264)
Signed-off-by: vaibhav-dahiya vdahiya@microsoft.com
This fixes the build for armhf to be able to use '/device///installer.conf' files. Specifically, armhf needs support to be able to change the size of /var/log/ directory. It is hardcoded to 512 bytes on all armhf platforms currently. This change will allow any armhf platform to be able to use an installer.conf file to customize the installed image.
* [Tunnel PFC] Tests for adding property 'sai_remap_prio_on_tnl_egress'
Add tests for adding property 'sai_remap_prio_on_tnl_egress', this
property should only be added in dual tor environment.
Test done:
Run test test_j2files.py
Co-authored-by: richardyu <richardyu@contoso.com>
Why I did it
Make reset didn't clean-up all fsroot folders.
How I did it
Remove all fsroot folders used during build.
How to verify it
Run local build and local make reset:
sudo mkdir fsroot-test
sudo touch fsroot-test/foo
make reset
(Without this change, make reset cannot remove fsroot-foo, with the change, the repo become clean after make reset.)
Signed-off-by: Ying Xie ying.xie@microsoft.com
- Why I did it
1. SN2201 sai profile needs to be updated according to the latest hardware.
2. In the reboot script, need to use the common symbol link of the power_cycle sysfs instead of directly accessing it due to SN2201 sysfs is different than other platforms.
3. echo 1 > $SYSFS_PWR_CYCLE will trigger the reboot immediately, the following sleep 3 and echo 0 > $SYSFS_PWR_CYCLE will never be executed, can be removed.
- How I did it
1. Replace the SN2201 sai profile with the latest one.
2. In the platform_reboot script, replace the direct sysfs path with the symbol link path.
3. Remove the redundant code from platform_reboot
- How to verify it
Perform reboot on all the Nvidia platforms, and check all can be rebooted successfully.
Signed-off-by: Kebo Liu <kebol@nvidia.com>
- Why I did it
"import sonic_platform" takes about 600ms ~ 1000ms, it is kind of slow. After this optimization, the time is about 100ms. The benefit is that those CLIs which does not need the slow import sentence would be faster than before.
- How I did it
Find slow import and call them when need.
- How to verify it
Measure the import time.
Why I did it
Some PR test are timing out on T1-lag kvm test.
How I did it
Increase the timeout to 5 hours.
How to verify it
Test on this PR.
Signed-off-by: Ying Xie ying.xie@microsoft.com
* [Tunnel PFC] Add property for tunnel PFC
Replace the config.bcm file with j2 template file
- Add 'sai_remap_prio_on_tnl_egress=1' property when device metadata local
- Host subtype is 'dualtor'
- Change sai.profile foe the new config.bcm.j2
Including change:
* 7ff8f75 2022-06-03 | Revert "[portsorch]: Prevent LAG member configuration when port has active ACL binding (#2165)" (#2306) (HEAD -> 202205, github/202205) [bingwang-ms]
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
#### Why I did it
No logs currently exist for sonic-save-X containers which makes it difficult to debug.
#### How I did it
Altered Makefile.work to create logs in the sonic-slave-X folder while still displaying the log to the screen to prevent interfering with any existing tooling.
#### How to verify it
Do `make configure` and verify that logs show up in `sonic-slave-buster/` and `sonic-slave-bullseye/`
#### Description for the changelog
Add logging for slave container builds
#### A picture of a cute animal (not mandatory but encouraged)
TBD
* When reloading config after crashes, VTEP interfaces are sometimes not created since the tunnel still exists in the STATE_DB.
* Adding VXLAN_TUNNEL_TABLE to the list of tables to be cleaned in swss.sh fixes the problem.
Currently, the build with ASAN_ENABLE=y reuses the packages built with
ASAN_ENABLE=n (and vice versa). To address this issue, ASAN_ENABLE is added to DEP_FLAGS for asan-enabled packages (docker-syncd-mlnx, syncd, docker-orchagent, swss).
- Why I did it
To make dpkg cache use/rebuild the packages for ASAN_ENABLE=y/n.
- How I did it
Added ASAN_ENABLE to the DEP_FLAGS for asan-enabled packages.
- How to verify it
Built with ASAN_ENABLE=y/n and checked the .flags .log files.
Signed-off-by: Yakiv Huryk <yhuryk@nvidia.com>
This is to improve the readability of ASAN reports. The debug package adds function names and source code references to the backtrace (currently, there are only binary addresses of functions)
Another way to address this issue is to build the image with "INSTALL_DEBUG_TOOLS=y". The downside of this approach is that the image size and compilation time are unnecessarily big. Also, the idea is to make the "ENABLE_ASAN" self-sufficient, which would not be the case for this approach.
- Why I did it
To improve the readability of asan logs.
- How I did it
Added SYNCD_DBG and SWSS_DBG to corresponding docker images for ASAN_ENABLE=y build
- How to verify it
Add artificial memory leak
Build with ASAN_ENABLE=y
Test the image and check the ASAN report
Signed-off-by: Yakiv Huryk <yhuryk@nvidia.com>
* Removed unused default_config.json
* Remove asic.conf file from HW SKUs directories as they are not used by upstream code
* Enable dynamic PCI ID identification on Otterlake2
Co-authored-by: Maxime Lorrillere <mlorrillere@arista.com>
Why I did it
Fix the target directory not empty issue when publishing artifacts.
Some of the artifacts are published to $(Build.ArtifactStagingDirectory)/target/ before source code checked out.
