#### Why I did it
Recently, the reserved buffer of admin-down ports is going to be reclaimed.
However, the way to do this differs among vendors.
We need to find a way to pass vendor information to swss docker.
#### How I did it
Fetch the ASIC vendor information when the docker is created and pass it to the docker as environment variable `ASIC_VENDOR`.
Why I did it
The time gap between last config load & db-listen seem to have increased.
Any config updates that occurred in this gap gets missed by db-listen.
This could miss updating /etc/pam.d/common-auth-sonic
How I did it
Add a one shot timer, just before db-listen. The timer will fire after the subscribe is done
When the timer fires, reload tacacs & aaa
In upgrade scenarios, where config_db.json is not carry forwarded to new image, it could be left w/o TACACS credentials.
Added a service to trigger 5 minutes after boot and restore TACACS, if /etc/sonic/old_config/tacacs.json is present.
How I did it
By adding a service, that would fire 5 mins after boot.
This service apply tacacs if available.
How to verify it
Upgrade and watch status of tacacs.timer & tacacs.service
You may create /etc/sonic/old_config/tacacs.json, with updated credentials
(before 5mins after boot) and see that appears in config & persisted too.
Encounter error during "config-setup boot" if the updategraph is enabled.
How I did it
Correct the code inside the config-setup script.
Remove the space between the assignment operator.
How to verify it
Remove the /etc/sonic/config_db.json and reboot the device.
Originally, it will return following error after boot up.
rv: command not found
After modification, it can correctly parse the status of updategraph without error.
* Support readonly vtysh for sudoers (#7383)
Why I did it
Support readonly version of the command vtysh
How I did it
Check if the command starting with "show", and verify only contains single command in script.
* Fix the type issue in rvtysh
This PR aims to monitor the memory usage of streaming telemetry container and restart streaming telemetry container if memory usage is larger than the pre-defined threshold.
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
The service file generate_monit_config.service is used to generate the Monit configuration file from template. I also should install this service file and enable it.
How I did it
I appended this service file name at the end of /etc/sonic/generated_services.conf.
How to verify it
I verified this on the device str2-7260cx3-acs-1.
Which release branch to backport (provide reason below if selected)
201811
[x ] 201911
202006
202012
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
This PR aims to monitor the critical processes in PMon container by Monit in 201911 branch.
How I did it
I created a template configuration file of Monit and it will be rendered to generate Monit configuration file of PMon container
by a service generate_monit_config.service.
How to verify it
I verified this on a Mellanox device str-msn2700-03 and an Arista device str-a7050-acs-1.
Which release branch to backport (provide reason below if selected)
201811
[x ] 201911
202006
202012
Signed-off-by: Yong Zhao yozhao@microsoft.com
Why I did it
This PR aims to monitor critical processes in router advertiser and dhcp_relay containers by Monit.
How I did it
Router advertiser container only ran on T0 device and the T0 device should have at least one VLAN interface
which was configured an IPv6 address. At the same time, router advertiser container will not run on devices of which
the deployment type is 8.
As such, I created a service which will dynamically generate Monit configuration file of router advertiser from a
template.
Similarly Monit configuration file of dhcp_relay was also generated from a template since the number of dhcrelay process in dhcp_relay container is depended on number of VLANs.
How to verify it
I verified this implementation on a DuT.
To run VNET route consistency check periodically.
For any failure, the monit will raise alert based on return code.
The tool will log required details.
This PR is cherry-pick of master
https://github.com/Azure/sonic-buildimage/pull/6920
Why I did it
Add support for BGP Monitors on multi asic SONiC platforms.
How I did it
On multi ASIC SONiC platforms, BGP monitor session will be established from Backend ASIC.
To achieve this following changes are done
Add BGP monitor configuration on the backend ASIC.
The BGP monitor configuration is present in the DPG of the device in minigraph.xml of multi-ASIC device, so this configuration will be added to the config_db of the host, when the minigraph is loaded.
To add configuration for this in the Backend ASIC, a new class MultiAsicBgpMonCfg is added to the hostcfgd service to update the config_db of the backend ASIC when the BGP_MONITOR table of the host config_db is updated.
This way incremental BGP_MONITOR configuration can also be handled.
Changes to establish BGP session with bgp monitor.
Add route in host main routing table to go to one of pre-define backend asic
Add IP table rule on front asic to mark the BGP packets with destination as IPv4 Loopback.
Add IP rule in front asic namespace to match mark BGP packet and lookup default table
Program the default route in FrontEnd asic name space docker default table as part of start.sh of the BGP container.
It need to be done as part of start.sh otherwise FRR default route will get over-written.
How to verify it
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
Co-authored-by: Arvind <arlakshm@microsoft.com>
To run VNET route consistency check periodically.
For any failure, the monit will raise alert based on return code.
The tool will log required details.
The Portchannels were not getting cleaned up as the cleanup activity was taking more than 10 secs which is default docker timeout after which a SIGKILL will be send.
Fix Issue #6537
Update topology script to retrieve hwsku from minigraph
if hwsku information is not available in config_db.
Fix clean up of interfaces in msft_multi_asic_vs hwsku
topology script.
- Why I did it
When bringing up multi-asic VS switch, topology service is started during boot up.
Topology service starts a shell script which runs the topology script present in /usr/share/sonic/device// directory. To invoke hwsku specific script, the topology script tries to retrieve hwsku information from config_db.
During initial boot up config_db might not be populated. In order to start topology service before config_db is updated,
update topology script to get hwsku information from minigraph.xml if it is available.
This will be helpful to bring up multi-asic VS testbed by loading minigraph and starting topology service.
- How I did it
Update topology.sh script to retrieve hwsku information from minigraph.xml.
Fix clean up function on msft_multi_asic_vs toplogy script.
- How to verify it
single-asic VS - no change; topology service is only enabled for multi-asic VS.
multi-asic VS - Bring up multi-asic VS image, copy minigraph to vs image, start topology service. Topology service should be successful.
to test clean up function fix, start topology service - make sure interfaces are created and moved to the right namespaces.
stop topology service - make sure namespace do not have any interface and all front end interfaces are present in default namespace.
What I did:-
For multi-asic platforms added iptable v4 rule to communicate on docker bridge ip
For multi-asic platforms extend iptable v4 rule for iptable v6 also
For multi-asic program made all internal rules applicable for all protocols (not filter based on tcp/udp). This is done to be consistent same as local host rule
For multi-asic platforms made nat rule (to forward traffic from namespace to host) generic for all protocols and also use Source IP if present for matching
This PR is port of #6845 for 201911
show ip interfaces is enhanced recently to support multi ASIC platforms in this Azure/sonic-utilities#1437. The ipintutil script as to run as sudo user, to get the ip interface from each namespace.
Add this script to the sudoer file so that show ip interface command is available for user with read-only permissions
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
Install pyroute2 for sonic-utilities. This change is needed for Azure/sonic-utilities#1437
[multi_asic][vs]: Add dependency in teamd service to start after topology service.
- Why I did it
In multi-asic VS, topology service is run after database service to set up the internal asic topology.
swss and syncd have a dependency to start after topology service is run so that the interfaces are moved to right namespace and created in the right namespace. In case of multi-asic vs, during the initial boot up, when there is no configuration added, teamd service starts and swss/syncd do not start as topology service does not start. Upon loading configuration using config_db or minigraph, swss and sycnd start up , but teamd is not restarted as swss is not stopped and started. This causes teamd to be in a bad state and requires a reload of config.
- How I did it
Add dependency in teamd service to start after topology service is completed.
- How to verify it
No change in single asic vs or platform.
No change in multi-asic regular image.
Change only in multi-asic VS. Bring up a multi-asic VS image without any configration, teamd service will fail to start due to dependency failure. Load minigraph, start topology service, load configuration, ensure all services come up.
Signed-off-by: SuvarnaMeenakshi <sumeenak@microsoft.com>
When large number of port channels (more than 64) is configured, a config reload command might ends with not all port channel configured and up. Further debug shows that unloading the port channels on the ASIC driver take a lot of time.
With the change, deleting all port channels before the syncd restart will free resources better and the ASIC driver will unload all netdev fast and the operation will execute properly.
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
- Why I did it
The command sudo ip netns identify <pid> is used in function get_current_namespace
to check in the cli command is running in host context or within a namespace.
This function is used for every CLI command and command sudo ip netns identify <pid> needs to be added in sudoer files to allow users with RO access to run show cli commands
This problem is not there on single asic platforms.
- How I did it
Add ip netns identify [0-9]* to sudoers file.
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan arlakshm@microsoft.com
- Why I did it
This PR has the changes to support having different swss.rec and sairedis.rec for each asic.
The logrotate script is updated as well
- How I did it
Update the orchagent.sh script to use the logfile name options in these PRs(Azure/sonic-swss#1546 and Azure/sonic-sairedis#747)
In multi asic platforms the record files will be different for each asic, with the format swss.asic{x}.rec and sairedis.asic{x}.rec
Update the logrotate script for multiasic platform .
Following changes were done for ebtables:
- Support for Multi-asic platforms. Ebtable filters are installed in namespace for multi-asic and not host. On Single asic installed on host.
- For Multi-asic platforms we don't want to install on host otherwise Namespace-to-Namespace communication does not happens since ARP Request are not forwarded.
- Updated to use text file to restore ebtables rules then the binary format. Rules are restore as part of Database docker init instead of rc.local
- Removed the ebtable service files for buster as not needed as filters are restored/installed as part of database docker init.
All the binaries are pre-installed with ebtables* binary are same as ebatbles-legacy-*
Signed-off-by: Abhishek Dosi <abdosi@microsoft.com>
Issue: Binary ebtables config file is CPU arch dependent
Fix: Load the text config during firsttime boot and
Generate the binary persistent atomic file
Signed-off-by: Antony Rheneus <arheneus@marvell.com>
In scenario where upgrade gets config from minigraph, it could miss tacacs credentials as they are not in minigraph. Hence restore explicitly upon load-minigraph, if present.
- Why I did it
Upon boot, when config migration is required, the switch could load config from minigraph. The config-load from minigraph would wipe off TACACS key and disable login via TACACS, which would disable all remote user access. This change, would re-configure the TACACS if there is a saved copy available.
- How I did it
When config is loaded from minigraph, look for a TACACS credentials back up (tacacs.json) under /etc/sonic/old_config. If present, load the credentials into running config, before config-save is called.
- How to verify it
Remove /etc/sonic/config_db.json and do an image update. Upon reboot, w/o this change, you would not be able ssh in as remote user. You may login as admin and check out, "show tacacs" & "show aaa" to verify that tacacs-key is missing and login is not enabled for tacacs.
With this change applied, remove /etc/sonic/config_db.json, but save tacacs & aaa credentials as tacacs.json in /etc/sonic/. Upon reboot, you should see remote user access possible.
- Why I did it
Move frr logs from syslog from the directory /var/log/quagga/.log to /var/log/frr/log
- How I did it
Updated the rsyslog config files.
- How to verify it
Verified the logs come into the file zebra.log and bgpd.log in the DIR /var/log/frr/log
Calls to sonic-cfggen is CPU expensive. This PR reduces calls to
sonic-cfggen to one call during startup when running interfaces-
config.
singed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
This PR limited the number of calls to sonic-cfggen to one call
per iteration instead of current 3 calls per iteration.
The PR also installs jq on host for future scripts if needed.
signed-off-by: Tamer Ahmed <tamer.ahmed@microsoft.com>
To limit IO and space usage on the flash device the boot0 script makes sure the SWI is in memory.
Because SONiC maps /tmp on the flash, some logic is required to make sure of it.
However it is possible for some provisioning mechanism to already download the swi in a memory file system.
This was not properly handled by the boot0 script.
It now properly detect if the image is on a tmpfs or a ramfs and keep it there if that is the case.
- How I did it
Check the filesystem on which the SWI pointed by swipath lies.
If this filesystem is a ramfs or a tmpfs the move_swi_to_tmpfs becomes a no-op.
Made sure the cleanup logic would not behave unexpectedly.
- How to verify it
In SONiC:
Download the swi under /tmp and makes sure it gets moved to /tmp/tmp-swi which gets mounted for that purpose.
Make sure /tmp/tmp-swi gets unmounted once the install process is done.
Create a new mountpoint under /ram using either ramfs or tmpfs and download the swi there.
Install the swi using sonic-installer and makes sure the image doesn't get moved by looking at the logs.
- Why I did it
The change is done to make sure the system initialization is done before the hostcfgd sets the feature states.
- How I did it
This is port of the PR #6232.
Since the systemctl version in 201911 doesn't support "--wait".
Added a function to check the output of systemctl is-system-running every second, till the command system is done booting up.
For now this change is only applicable to multi asic platforms based on the testing this change will be extended to all platforms in the future PR.
Signed-off-by: Arvindsrinivasan Lakshmi Narasimhan <arlakshm@microsoft.com>
Fixes#5663
- Why I did it
It's currently possible for the SNMP timer to conflict with config reload (specifically if the timer triggers while config reload is stopping the SWSS service). config reload triggers SWSS to shutdown, which causes SNMP to shutdown, which conflicts with the SNMP timer causing SNMP to startup. See the linked issue for more details.
- How I did it
Including the After ordering dependency forces the SNMP timer to wait until SWSS finishes stopping, preventing the conflict. If there is an ordering dependency between two units (e.g. one unit is ordered After another), if one unit is shutting down while the other is starting up, the shutdown will always be ordered before the startup. In this case, that means that the SNMP timer is forced to wait for the SWSS shutdown to complete. Only then can the SNMP timer proceed. See here for more details.
It's important to note that the After dependency will not cause SWSS to be started when the SNMP timer fires (assuming that SWSS has not yet been started). The existing Requisite dependency in the SNMP service will also not cause SWSS to be started, instead it will cause the SNMP service to fail if SWSS is not active.
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
In order to install a SONiC image on top of a NVMe SSD disc properly with ONIE we must configure it properly on the installer.sh script.
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
Added new flag value 'always_enabled' for the state and auto-restart field of feature table
init_cfg.json is updated to initialize state field of database/swss/syncd/teamd feature and auto-restart field of database feature
as always_enabled
Once the state/auto-restart value is initialized as "always_enabled" it is immutable and cannot be change via feature config commands. (config feature..) PR#Azure/sonic-utilities#1271
hostcfgd will not take any action if state field value is 'always_enabled'
Since we have always_enabled field for auto-restart updated supervisor-proc-exit-listener
not to have special check for database and always rely on value from Feature table.
When forced mgmt routes are present, the issue fixed as part of #5754 is not complete.
Added a preference(priority) field to forced mgmt route ip rules
* Add explicit default state into the constants.yml
* Enable/disable only peer-groups, available in the config
* Retrieve updates from frr before using configuration
Co-authored-by: Pavel Shirshov <pavel.contrib@gmail.com>
* Remove 'backend' from device type strings so that backend devices ('BackEndToRRouter' and 'BackEndLeafRouter') are given the same cable lengths as regular device types.
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
Treat devices that are ToRRouters (ToRRouters and BackEndToRRouters) the same when rendering templates
Except for BackEndToRRouters belonging to a storage cluster, since these devices have extra sub-interfaces created
Treat devices that are LeafRouters (LeafRouters and BackEndLeafRouters) the same when rendering templates
Signed-off-by: Lawrence Lee <lawlee@microsoft.com>
To make Control plane ACLs handle case insensitive ACL rules. Currently, it handles only upper case ACL rules.
Co-authored-by: Madhan Babu <madhan@arc-build-server.mtr.labs.mlnx>
