Why I did it
serial-getty service exited in Dell S6100 device randomly.
How I did it
Added serial-getty to monit services.
How to verify it
Stop serial-getty in ssh session and check whether the service restarts or not.
Why I did it
To monitor the SSD health condition in DellEMC S6100 platform post upgrade.
A daemon is introduced to monitor the SSD every one hour.
To check for SSD status at boot time and at the time of cold-reboot.
All these changes are supported only for newer SSD firmware.
Porting changes from 201911 branch
Added a platform_reboot_pre_check script to prevent cold-reboot based on SSD status.
Depends on Azure/sonic-utilities#1557
Why I did it
The S6000 devices, the cold reboot is abrupt and it is likely to cause issues which will cause the device to land into EFI shell. Hence the platform reboot will happen after graceful unmount of all the filesystems as in S6100.
How I did it
Moved the platform_reboot to platform_reboot_override and hooked it to the systemd shutdown services as in S6100.
Fixed the "/host unmount failed" issue as well in 201811.
How to verify it
Issue "reboot" command to verify if the reboot is happening gracefully.
#### Why I did it
- The iSMT SMBUS I2c bus number conflicts in different kernel versions.
#### How I did it
- Add I2cbus number detector for iSMT bus
- Replace iSMT bus number in fancontrol config
when parallel build is enabled, both docker-fpm-frr and docker-syncd-brcm
is built at the same time, docker-fpm-frr requires swss which requires to
install libsaivs-dev. docker-syncd-brcm requires syncd package which requires
to install libsaibcm-dev.
since libsaivs-dev and libsaibcm-dev install the sai header in the same
location, these two packages cannot be installed at the same time. Therefore,
we need to serialize the build between these two packages. Simply uninstall
the conflict package is not enough to solve this issue. The correct solution
is to have one package wait for another package to be uninstalled.
For example, if syncd is built first, then it will install libsaibcm-dev.
Meanwhile, if the swss build job starts and tries to install libsaivs-dev,
it will first try to query if libsaibcm-dev is installed or not. if it is
installed, then it will wait until libsaibcm-dev is uninstalled. After syncd
job is finished, it will uninstall libsaibcm-dev and swss build job will be
unblocked.
To solve this issue, _UNINSTALLS is introduced to uninstall a package that
is no longer needed and to allow blocked job to continue.
Signed-off-by: Guohan Lu <lguohan@gmail.com>
backport c4b5b002c3
make swss build depends only on libsairedis instead of syncd. This allows to build swss without depending
on vendor sai library.
Currently, libsairedis build also buils syncd which requires vendor SAI lib. This makes difficult to build
swss docker in buster while still keeping syncd docker in stretch, as swss requires libsairedis which also
build syncd and requires vendor to provide SAI for buster. As swss docker does not really contain syncd
binary, so it is not necessary to build syncd for swss docker.
[submodule]: update sonic-sairedis
* 9a66890 2020-06-28 | [build]: add option to build without syncd (HEAD -> 201811, origin/201811) [Guohan Lu]
Signed-off-by: Guohan Lu <lguohan@gmail.com>
Haliburton needed watchdog daemon to monitor the basic health of a machine. If something goes wrong, such as a crashing program overloading the CPU, or no more free memory on the system, watchdog can safely reboot the machine,
During platform deinitialization, dell_ich is not removed properly and when we do initialize s6100 platform, ICH driver sysfs attributes are not attached. Because of this, get_transceiver_change_event returns error and this leads xcvrd to crash.
* [platform/cel-dx010]: add gpio init for fan direction
* [platform/cel-dx010]: remove invalid code on fancontrol service
* [platform/cel-dx010]: modify fancontrol service permission
* [platform/cel-dx010]: install fancontrol in pmon
If a device had a master or 201911 image then installed a 201811 image, it could result in a prefdl that was not properly processed by 201811 Arista code.
This is a commit that was on 201911 and master branch.
Co-authored-by: Zhi Yuan Carl Zhao <zyzhao@arista.com>
Fix the method get_transceiver_change_event to abide by the function description, return True status and use timeout in milliseconds.
Co-authored-by: Zhi Yuan Carl Zhao <zyzhao@arista.com>
Update fancontrol service for Seastone-DX010/E1031 device to support hysteresis temperature threshold and difference config for each unit fan direction type (B2F/F2B); follow master branch
- Broadcom SAI 3.5 GA code drop on 20200608.
Changes:
- CS9533198
- CS10283709
- CS00009716645
- CS00010389861
- CS00010406122
- CS00010503275
- Addressed a few memory leak issues.
- Addressed an array memory allocation issue.
- Addressed assert during SER handling.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
Since the syncd process running on different platforms will have the different full path names, we
change the full path name of process syncd in the monit config file such that it will be universal and is not for a specific vendor.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for teamd container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file in teamd container
into base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for snmp container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of snmp container into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for dhcp_relay container in the dir
base_image_files.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of dhcp_relay
container into base image under /etc/monit/conf.d.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a monit config file for router advertiser container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* Add a copy mechanism to put the monit config file of router advertiser
contianer into base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Pmon] Add a monit config file for pmon container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Pmon] Add a copy mechanism to put the monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Add a monit config file for lldp container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Add a copy mechanism to put the monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Add a monit config file for BGP container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Add a copy mechanism to put monit config file into the base
image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Add a monit config file for the swss container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Add a copy mechanism to put monit config file into the
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on barefoot
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-centec] Add a monit config file for syncd container on centen
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on centen
platform.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit conifg file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on
marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image on marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on
marvell-armhf.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a monit config file for syncd container on nephos.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Add a monit config file for sflow container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Add a copy mechanism to put the monit conifg file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Add a monit config file for telemetry container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Add a copy mechanism to put the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Add a monit config file for database container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Add a copy mechanism to put the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Dhcprelay] Change a typo.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Dhcprelay] Change the process name in monit config file to
dhcrelay.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no desserve process in syncd container on
barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process desserve in syncd container on
cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process named desserve in syncd on centec.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] There is no process named desserve in syncd on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Should not delete the process desserve in syncd container
on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
marvell-arm64.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
marvell-armhf.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Delete the process dsserve in syncd container on
mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-Radv] Change the process name to radvd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Correct a typo in monit_telemetry.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-teamd] Delete the monit config file for teamd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-teamd] Delete the mechanism to copy the monit config file into
base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-dhcprelay] Delete the monit config file for dhcp_relay
container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-dhcprelay] Delete the mechanism to copy the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-radv] Delete the monit config file foe radv container.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-radv] Delete the mechanism to copy the monit config file into
the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] change the monit config file for BGP container such that
monit only generates alert if the process is not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-snmp] Change the monit config file for snmp container such that
monit only generates alret if the process is not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Change the monit config file for pmon container such that
monit only generates alert if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Change the monit config file for lldp container such that
monit only generates alerts if some processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Delete the monit config file for pmon container since some
of processes are not running depended on the type of box.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-pmon] Delete the copy mechanism to copy the monit config file
into the base image.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Change the matching name for the process lldpd.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Change the monit config file for swss container such that
monit only generates alerts if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
barefoot such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Correct a typo in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
broadcom such that monit only generates alerts if the processes are not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
cavium such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container such
that monit only generates alerts if the process is not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell-arm64 such that monit only generates alerts if the process is
not running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
marvell-armhf such that monit will generate alert if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Change the monit config file for syncd container on
mellanox such that monit only generates alerts if the process is not
running for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sycnd] Change the monit config file for syncd container such
that monit only generates alerts if the processes are not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Change the monit config file for sflow container such
that monit only generates alerts if the process is not running for 5
minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Change the monit config file for telemetry container
such that monit only generates alerts if the processes are not running
for 5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Change the monit config file for database container
such that monit only generates alerts if the process is not running for
5 minutes.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-database] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Use 4 spcess to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-lldp] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-swss] Use 4 spaces to replace 2 space in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-sflow] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-snmp] Use 4 spaces to replace 2 spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-telemetry] Use 4 spaces to replace 2 spaces in monit config
file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on barefoot.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on broadcom.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on cavium.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on centec.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on marvell.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to replace 2 spaces in the monit config file
on mellanox.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-syncd] Use 4 spaces to repalce 2 spaces in the monit config file
on nephos.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
* [Docker-bgp] Remove the trailing extra spaces in monit config file.
Signed-off-by: Yong Zhao <yozhao@microsoft.com>
- What I did
Added Daemon to Log LPC bus degradation in Intel C2000 processor. Intel Rangeley C2000 processors with revision less than or equal to 2 have issue where LPC bus degrades over time in some processors. To identify the problem and to notify the issue, a daemon has been added which will log on encountering the issue.
- How I did it
Added a daemon which validates the CPLD scratch(0x102) and SMF scratch(0x202) registers by writing and reading values on regular polling intervals (300 seconds). If there is a discrepancy between read and write, a critical log will be thrown.
- How to verify it
The infra is verify by simulating the issue where between write and read, the value in register is modified and the log appearance is checked.
- Description for the changelog
Added Daemon to identify LPC bus degradation issue and notify using syslog in Dell S6100 and Z9100 platforms. This daemon will only run on processors with revision less than or equal to 2.
Rely on platform= and sid= on the command line to detect the platform rather than the eeprom
The platform will now properly initialize even if the system eeprom died or is unreachable.
Add support for the 7260CX3-64E
This is a variant of the 7260CX3-64 with no real difference for software.
* Remove the divide by 4 operation to the under the hood SAI
This is to avoid the need and thus the confusion for application program to know
the mmu internal architecture
This change must have support from SAI change to reach the correct
config
Signed-off-by: Wenda <wenni@microsoft.com>
* Relegate the divide by 4 operation to the under the hood SAI for egress
lossless pool
Extend to 7060 and 6100
Signed-off-by: Wenda <wenni@microsoft.com>
* Add more TH/TH2 hwskus
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Update config test
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Add TH2 ingress lossy profile
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* Move the divide by 4 operation to SAI internal
Signed-off-by: Wenda Ni <wenni@microsoft.com>
* [bcm SAI] Upgrade Broadcom SAI to version 3.5.3.1-15
- Broadcom SAI 3.5 GA release 20190924.
Signed-off-by: Ying Xie <ying.xie@microsoft.com>
- Improve smbus reliability for all platforms
- Delay processing of the reboot cause to reduce critical path
- Add support of get_change_event for PSUs
