- Why I did it
To include latest SDK fixes:
1. On CMIS modules, after low power configuration, the firmware waited for the module state to be ModuleReady instead of ModuleLowPower causing delays.
2. When connecting SN4600C, 100GbE port with CWDM4 module (Gen 3.0), link up time is 30 seconds.
and to include SAI fixes \ changes:
1. Reduce verbosity for resource check vendor data not found
2. Fix metadata validation, check default value on conditions check
3. Add 100MB, 10MB to 2201 system
4. L3 VXLAN overlay ECMP
5. VXLAN srcport API implementation
6. Fix scheduler profile null (default values) when set on sub group scheduler group
7. Fix ACL binding restoration when port leaves a LAG
8. Fix route logic for set next hop/action and reference counter for ECMP overlay
- How I did it
1. Updated SDK/FW submodule and relevant makefiles with the required versions.
2. Update SAI submodule and relevant makefile with the required version.
- How to verify it
Build an image and run tests from "sonic-mgmt".
- Why I did it
To include latest fixes.
SAI
1. Reclaim buffers for port which is admin down
2. Support for Spectrum-4 os Nvidia ASIC simulation
3. Support for SN2201
4. Fix host interface table entry, one channel per trap (fix sflow double registration)
5. 2 new queue counters - ecn marked packets + shared current occupancy
6. Fix storm policer unknown unicast
7. Add key/value for accuflow counters
8. Add MAC move
9. Add mirror congestion mode attribute
SDK
1. Under various circumstances, Ethernet ports falsely showed that InfiniBand cables were connected.
2. In SN4600C, at times, the link up time in both DAC and optics cables may, in the worst case, take up to 15 seconds.
3. Using SN4600C with copper or optics loopback cables in NRZ speeds, link may raise in long link up times
4. When ECMP has high amount of next-hops based on VLAN interfaces, in some rare cases, packets will get a wrong VLAN tag and will be dropped.
5. When connecting Spectrum devices with optical transceivers that support RXLOS, remote side port down might cause the switch firmware to get stuck and cause unexpected switch behavior.
6. Aggregation event is missing for WJH L2 drop reason 'Unicast egress port list is empty'.
7. Tying the SCL and SDA of the optical modules to 3.3V causes errors.
8. On SN4600, there was a delay of more than 10 seconds from the time a data packet is sent from CPU until it is transmitted through one of the switch ports.
9. While using SN4600C system with Finisar FTLC1157RGPL 100GbE CWDM4 modules, intermittent link flaps across multiple ports may be observed.
10. In Spectrum-2 and Spectrum-3 systems, link did not work in auto-negotiation when connected to Marvell PHY. KR mechanism has been enhanced to integrate with Marvell PHY.
11. The tunnel counter counts the drop packets now for Spectrum-2 and Spectrum-3 and consistent with Spectrum behavior and count the ECN dropped packets as well.
12. When connecting SN3800 to Cisco-9000, fast-linkup flow will fail and will rise in the normal flow.
13. Race condition in WJH library: when multiple threads load the LAG shared memory concurrently, the program may crash.
14. Add WJH L2 drop reason 'Unicast egress port list is empty' as a new drop reason.
15. Fixed a memory leak in sx_api_port_sflow_statistics_get API.
16. During initialization flow, the command interface that is used by the minimal driver and SDK caused the collision in the firmware since the same buffer is used in the firmware for the two interfaces.
17. Fix route issue on Kernel 5.10
- How I did it
Updated SDK/SAI submodule and relevant makefiles with the required versions.
- How to verify it
Build an image and run tests from "sonic-mgmt".
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
- Why I did it
Advance to new Nvidia SAI release with the following changes:
New features:
- Align with new SDK/FW version 4.5.1006 and above and in parallel to existing used SDK/FW bundle
- Implement timestamp and egress_queue_index hostif packet attributes.
Bugs fixes:
- Fix compilation issues with gcc10
- Fix return code for buffer overflow for query enum values and query statistics capabilities
- Reduce verbosity of print in case packet ingress on invalid port
- Fix mirror Qos settings
- How I did it
Updated SAI version and submodule pointer
- How to verify it
Run regression tests from sonic-mgmt
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
- Why I did it
Advance to Mellanox SAI ver 1.19.2 to pick up dynamic Policy Based Hashing support.
For this version above the static Policy Based Hashing is no longer supported.
For detailed release notes check https://github.com/Mellanox/SAI-Implementation/blob/sonic2111/release%20notes.txt
- How I did it
Updated SAI-Implementation submodule
- How to verify it
1. make configure PLATFORM=mellanox
2. make target/sonic-mellanox.bin
Run full regression as well as new dynamic PBH tests
Signed-off-by: Nazarii Hnydyn <nazariig@nvidia.com>
- Why I did it
Update SAI version to 1.19.1. The following was changed:
1. Update license
2. Do not remove and re-apply the same SDK mirror session on LAG
3. FEC fix to support all speeds
4. Improve PG counters performance
5. Fix number of switch priorities for port mirroring
Signed-off-by: Dror Prital <drorp@nvidia.com>
- Why I did it
* For SAI - Advance to adopt the following fixes:
1. Better handle not implement object type for resource availability
2. Fix ext dump when saidump is triggered from 2nd process (saidump utility) other than main adapter host (syncd in SONiC)
* For SDK\FW:
- Changes and new features:
1. Added support in SN4600C systems for new module Finisar ET7402-CWDM4 (100G CWDM4 QSFP28 1310nm SM 2KM).
2. Added support for new module MMS1W50-HM (2km transceiver FR4) for 200GbE
3. Improved performance of "per-port-buffer" counters
4. Added support for Kernel 5.10
- Bugs fixes:
On rare occasions (0.5%), in SN4600C systems, when using 100GbE NRZ mode and Fastboot flow, the link up time may take up to 10 seconds
Signed-off-by: Dror Prital <drorp@nvidia.com>
Split and bulk counter bug fixes:
- Init port auto neg to default on static (SAI XML) port split for 2nd+ port
- Fix port stats SAI_PORT_STAT_WRED_DROPPED_PACKETS, SAI_PORT_STAT_ECN_MARKED_PACKETS, SAI_PORT_STAT_ETHER_TX_OVERSIZE_PKTS
- Hide error message when reading not implemented port stat
Signed-off-by: Shlomi Bitton <shlomibi@nvidia.com>
Why I did it
* For SAI - Upgrade to Version 1.19.0
- Add support for VxLAN encap TTL uniform model on SPC2/3
- Add ACL entry actions set VRF, set do no learn, add VLAN ID, add VLAN priority
- Add ACL field has VLAN tag
- Bulk counters (improve port statistics performance)
- Create async dump extra as part of debug generate dump
- Create irisc dump on severe health event
- Support 0 port systems (modify get switch mac to work accordingly)
- Set interface vlan up state for ping tool in SONiC
- Support attributes SAI_PORT_ATTR_QOS_SCHEDULER_PROFILE_ID, SAI_PORT_ATTR_QOS_INGRESS_BUFFER_PROFILE_LIST,
SAI_PORT_ATTR_QOS_EGRESS_BUFFER_PROFILE_LIST, SAI_PORT_ATTR_POLICER_ID as part of port create Git stats
* For SDK\FW - Upgrade to Version SDK 4.4.3106, FW 2008_3110
Added Features:
- Increased ACL table
- Enhanced PSAMPLE support
- Added support for Finisar SR4 module in SN3700 systems
- Added support for Python 3.0 in examples.
Fix bugs:
- On LR4 transceivers 00YD278, the firmware incorrectly identified the transceiver
- Reduce memory consumption for virtual LAG
- Fixed PSAMPLE listeners cleanup on SDK drivers unloading.
- On Spectrum-2 and Spectrum-3 systems, slow reaction time to Rx pause packets may lead to buffer overflow on servers.
- BER may be experienced when using 5m DAC cables between SN4700 and SN2700 in 100GbE speed.
- On very rare occasion, when connecting DR4 PAM4 transceiver to 100GbE DR1 NRZ, low BER may be experienced.
- Unexpected packet drops on the port ingress buffer may be experienced when working in 400GbE mode.
Note: When performing ISSU from an older version, this fix won't be applied. For fix to apply, a non-ISSU reset is required.
- Fix SN3800 specific warm boot scenario: Disable interface, Warm Boot, Enable Interface --> link will remain down.
Signed-off-by: Dror Prital <drorp@nvidia.com>
Changes in the new release:
Fix 10G and 50G speeds in SAI XML to support all interface types
Enable SMAC=DMAC and SMAC MC in tunnel debug counter
Add tunnel statistics
Add isolation group API implementation
Fix ACL ANY debug counter to correctly track ACL drops
Add VXLAN source port hard coded range, controlled by K/V
FW dump me now feature
Add mlxtrace to saidump
Speed lane setting and AN control
Implement query stats API
VNI miss part of tunnel decal drop reason
Align with SAI API v1.8.1
Signed-off-by: Dror Prital <drorp@nvidia.com>
- Why I did it
To pick up new features and fix from SDK/FW and SAI
SDK/FW new Feature:
All | Added support for multiple modules and cable types. For full list contact Nvidia networking support
Spectrum-3 | SN46000C | Added support for up to 5W on ports 49 to 64 .
SDK/FW bugs' fix:
All | fast reboot | fast boot failure from latest 201811 to 201911 and above
Spectrum | 10GbE/1GbE Transceiver (FTLX8574D3BCV) stopped working after firmware upgrade
Spectrum-2 | When device is rebooted with locked Optical Transceivers in split mode, the firmware may get stuck
Spectrum-2 | SN3700 | When connecting at 200GbE to Ixia K400, Ixia receives CRC errors
Spectrum-2 | SN3800 | On rare occasions packets loss may be experienced due to signal integrity issues
Spectrum-2 | When the port is a member of a LAG, after a warmboot and port toggle on the peer-side, the port remains down
Spectrum-3 | SN4700 | While using Optic cable in Split 4x1 mode in PAM4, when two first ports are toggled, the other 2 ports go down
Spectrum-3 | SN4700 | When working in 400GbE, deleting the headroom configuration (changing buffer size to zero) on the fly may cause continual packet drops
SAI
All | sFlow | Use hardcoded value 1 as netlink group number ax expected by hsflowd
- How I did it
Update the related version number in the make files and update the submodule pointer accordingly.
- How to verify it
Run regression test and everything works good.
Open ACL Outer VLAN ID for egress for ports part of VLAN RIF
- Why I did it
Open ACL Outer VLAN ID for egress for ports part of VLAN RIF
- How I did it
Updated SAI submodule pointer
- How to verify it
Build an image, deploy and check all is up and running.
Verify ACL sonic-mgmt test is passing
Signed-off-by: Volodymyr Samotiy <volodymyrs@nvidia.com>
Include SAI bug fixes:
- Apply device MAC on port host interface when port is removed from LAG.
- [Shared Headroom]: fixed watermark handling for SHP flow
- Decrease verbosity of policer unbind message when no policer is attached
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
**Why I did it**
Disable SDK extended dump due to issue found
**How I did it**
Update SAI submodule
**How to verify it**
Verify the SDK extended dump is not called.
Signed-off-by: Eran Dahan <erand@nvidia.com>
Changes in the new release:
1. Policy based hashing optimization
2. New attribute support for Max port headroom
3. Tunnel ECN map fixes
4. Tunnel EVPN skeleton extensions (peer attrib, maps)
5. Bridge port admin not affecting port admin (optimize port down time)
6. CRM new API for neighbors and tunnel termination entries
7. Improve FDB event for flush by bridge port (before, null bridge was reported to SONiC, now the bridge will be extracted from bridge port)
8. DHCP L2 v4+v6 traps (for ZTP use case)
9. Generic counter implementation
Signed-off-by: Kebo Liu <kebol@nvidia.com>
* [Mellanox] Update SAI to 1.18.0
* [Mellanox] Update SDK to 4.4.2112
* Updated Mellanox SAI to 1.18.0.2
* Updated bcmsai debians to use SAI 1.7.1
* Updated Mellanox to use SAI 1.7.1
* Updated submodule sonic-sairedis using SAI 1.7.1
Co-authored-by: Vineet Mittal <vmittalmittal@microsoft.com>
Co-authored-by: Nazarii Hnydyn <nazariig@nvidia.com>
Example of syslog message from Mellanox SAI:
"Oct 7 15:39:11.482315 arc-switch1025 INFO syncd#supervisord: syncd Oct 07 15:39:11 NOTICE SAI_BUFFER: mlnx_sai_buffer.c[3893]- mlnx_clear_buffer_pool_stats: Clear pool stats pool id:1"
There is a log INFO from supervisord which actually printed NOTICE and
date again. This confusion happens becuase if SAI is not built to log
to syslog it will log everything to stdout with format "[date] [level]
[message]" so supervisord sends it to syslog with level INFO.
New logs look like:
"Oct 7 15:40:21.488055 arc-switch1025 NOTICE syncd#SDK [SAI_BUFFER]: mlnx_sai_buffer.c[3893]- mlnx_clear_buffer_pool_stats: Clear pool stats pool id:17"
Signed-off-by: Stepan Blyschak <stepanb@nvidia.com>
1. Upgrade SAI headers to v1.6.3
2. Fix traffic lost during FFB related to buffer config + optimize buffer config timing for FB
3. Add ACL fields BTH, IP flags
4. Add ACL infrastructure of different fields per ASIC type
* Update sonic-sairedis (sairedis with SAI 1.6 headers)
* Update SAIBCM to 3.7.4.2, which is built upon SAI1.6 headers
* missed updating BRCM_SAI variable, fixed it
* Update SAIBCM to 3.7.4.2, updated link to libsaibcm
* [Mellanox] Update SAI (release:v1.16.3; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* Update sonic-sairedis pointer to include SAI1.6 headers
* [Mellanox] Update SDK to 4.4.0914 and FW to xx.2007.1112 to match SAI 1.16.3 (API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* ensure the veth link is up in docker VS container
* ensure the veth link is up in docker VS container
* [Mellanox] Update SAI (release:v1.16.3.2; API:v1.6)
Signed-off-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
* use 'config interface startup' instead of using ifconfig command, also undid the previous change'
Co-authored-by: Volodymyr Samotiy <volodymyrs@mellanox.com>
Update SAI/SDK/FW and MSN4700 device files to support 8 lanes 400G
Update SAI to 1.16.3
Update SDK to 4.4.0914
Update FW to *.2007.1112
Update MSN4700 device files to support 8 lanes 400G
update FW to xx_2000_3298
update SAI to 1.16.0
update Spectrum-1 and Spectrum-2 buffer pool size according to the new SDK default config change.
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn2700-r0/ACS-MSN2700/buffers_defaults_t1.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t0.j2
modified: ../../device/mellanox/x86_64-mlnx_msn3700-r0/ACS-MSN3700/buffers_defaults_t1.j2
modified: fw.mk
modified: mlnx-sai.mk
modified: mlnx-sai/SAI-Implementation
modified: sdk-src/sx-kernel/Switch-SDK-drivers
modified: sdk.mk
signed-off by kebol@mellanox.com
* [submodule] update sonic-linux-kernel
* update linux kernel version
* Fix many version strings
* update mellanox components (built with new kernel)
* [mlnx] add make files for SDK WJH libs
* Update arista driver submodule (#8)
Make the debian packaging point to a newer kernel version.
* Build improvements
Fix dependencies
Add configuration options
Automatically build sonic-slave
* Set default number of jobs to 1
* Auto generate target/debs directory
Signed-off-by: marian-pritsak <marianp@mellanox.com>
* Automatically remove sonic-slave container after exit
* Silence clean-logs
* Add SONIC_CLEAN_TARGETS to clean
* Use second expansion for clean dependencies
* Avoid creating empty log files
Remove log file on flush instead of writing empty string
* Put dpkg install inside lock
Use same lock as debian install targets do to avoid
race condition in dpkg installation
* Remove redirect to log from docker save
* Add .platform dependency to all and clean targets
* Remove header and footer from clean targets
* Disable messages for SONIC_CLEAN_TARGETS
* Exit with error if dpkg-buildpackage fails
* Set new location for debs in build_debian.sh
* Add recipe for docker-database
* Update redis version to 3.2.4
* Add support for p4 platform
* Add recipe for snmpd
* Add slave targets to phony and make all target default
* Remove build.sh from thrift
* Add versioning to team, nl, hiredis and initramfs
* Change sonic-slave to support snmpd build from sources
* Remove src/tenjin
* Add recipe for lldpd
* Add recipe for mpdecimal
* Remove hiredis directory on rebuild
* Add recipe for Mellanox hw management
* Remove generic image from all targets for Mellanox
* Add support for python wheels
* Add lldp and snmp dockers
* Sync docker-database to include libjemalloc
* Fix asyncsnmp variable name
* Change default build configuration
Redirect output to log files by default
Set number of jobs to nproc value
Do not print dependencies
Fix logging to print log of failed job into console
* Use docker inspect to check if sonic-slave image exists
* Use config in slave.mk directly
* Disable color output by default
* Remove sswsdk dependency from lldp and snmp dockers
* Fix comment in py wheels install targets
* Add dependency between two versions of sswsdk
* Add containers to mellanox platform
lldp, snmp and database containers
* Add recipe for team docker
* Add team docker to mellanox platform
* Encrypt password passed to build_debian.sh
* Update mellanox SAI version
Make version and revision setting only in main recipe
* Fix error handling in makefiles
As makefiles use .ONESHELL we should add -e
option to shell options in order to exit after any command fails
* Add recipe for platform monitor image
* Add platfotm monitor to mellanox targets
* Ignore submodules when building base image
