- SAI-1.11.0 support
- SONIC 20220531.25 OC Failure: Everflow testcases failing due to SAI orchagent crash
- SONIC 20220531.25 OC Failure: ACL IPv6 testcases.
- TPID support
Signed-off-by: rajkumar38 <rpennadamram@marvell.com>
Using timer-override.conf, we modify the fstrim.timer service.
For armhf, Nokia-7215 platform, we modify fstrim.timer to run daily
instead of weekly. This is required because the size of the SSD on
this platform is 16GB, which on average is nearly 10 times smaller than
most other sonic platforms. With smaller disk and the ever increasing
level of logging done by sonic, this change is required to prevent
the SSD from entering a read-only state due to inadequate free blocks.
Why I did it
After sonic-install install a new image, print_menu is set echo without any data. No image info between Hit any key to stop autoboot: 0 and Start USB
Board configuration detected:
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
No ethernet found.
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: Port (usbActive) : 0 Interface (usbType = 2) : USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
How I did it
The fw_setenv print_menu is missing the double quotes. That causes the value is truncated. Using double quotes to in the environment setting.
How to verify it
Install new image with this fix. And reboot the system. The following section should be shown:
Signed-off-by: mlok <marty.lok@nokia.com>
Why I did it
High CPU utilization by entropy.py
How I did it
Remove entropy script as it does not work anymore and is no longer needed for bullseye(202205).
In Buster(202012) the max available poolsize (entropy_avail) for entropy is 4096 and our entropy.py script was based on this value. With the change in kernel to bullseye on 202205 this entropy poolsize was changed to 256 which also causes our script to fail.
This script was initially added to provide SW assistance to improve the system entropy value available early on in the Sonic boot sequence on buster.
On bullseye (Linux kernel 5.10) this is no longer needed as this feature has been improved.
How to verify it
run "top" command to check CPU usage.
Why I did it
Command "sudo sfputil show error-status -hw" shows "OK (Not implemented)" in the output.
How I did it
Add a new SFP API get_error_description support in Nokia sonic-platform sfp.py module.
How to verify it
Run the new image and execute command "sudo sfputil show error-status -hw"
- Why I did it
Support syslog rate limit configuration feature
- How I did it
Remove unused rsyslog.conf from containers
Modify docker startup script to generate rsyslog.conf from template files
Add metadata/init data for syslog rate limit configuration
- How to verify it
Manual test
New sonic-mgmt regression cases
Signed-off-by: maipbui <maibui@microsoft.com>
Dependency: [https://github.com/sonic-net/sonic-buildimage/pull/12065](https://github.com/sonic-net/sonic-buildimage/pull/12065)
#### Why I did it
`subprocess.Popen()` and `subprocess.run()` is used with `shell=True`, which is very dangerous for shell injection.
`os` - not secure against maliciously constructed input and dangerous if used to evaluate dynamic content
`getstatusoutput` is dangerous because it contains `shell=True` in the implementation
#### How I did it
Replace `os` by `subprocess`, use with `shell=False`
Remove unused functions
Why I did it
Move armhf syncd docker compilation to bullseye.
How I did it
compile syncd docker for armhf platform using below commands,
NOJESSIE=1 NOSTRETCH=1 NOBUSTER=1 BLDENV=bullseye make configure PLATFORM=marvell-armhf PLATFORM_ARCH=armhf
NOJESSIE=1 NOSTRETCH=1 NOBUSTER=1 BLDENV=bullseye make target/docker-syncd-mrvl.gz
How to verify it
upgrade the syncd docker and verify ports are up.
Signed-off-by: rajkumar38 <rpennadamram@marvell.com>
* Ported Marvell armhf build on x86 for debian buster to use cross-compilation instead of qemu emulation
Current armhf Sonic build on amd64 host uses qemu emulation. Due to the
nature of the emulation it takes a very long time, about 22-24 hours to
complete the build. The change I did to reduce the building time by
porting Sonic armhf build on amd64 host for Marvell platform for debian
buster to use cross-compilation on arm64 host for armhf target. The
overall Sonic armhf building time using cross-compilation reduced to
about 6 hours.
Signed-off-by: marvell <marvell@cpss-build3.marvell.com>
* Fixed final Sonic image build with dockers inside
* Update Dockerfile.j2
Fixed qemu-user-static:x86_64-aarch64-5.0.0-2 .
* Update cross-build-arm-python-reqirements.sh
Added support for both armhf and arm64 cross-build platform using $PY_PLAT environment variable.
* Update Makefile
Added TARGET=<cross-target> for armhf/arm64 cross-compilation.
* Reviewer's @qiluo-msft requests done
Signed-off-by: marvell <marvell@cpss-build3.marvell.com>
* Added new radius/pam patch for arm64 support
* Update slave.mk
Added missing back tick.
* Added libgtest-dev: libgmock-dev: to the buster Dockerfile.j2. Fixed arm perl version to be generic
* Added missing armhf/arm64 entries in /etc/apt/sources.list
* fix libc-bin core dump issue from xumia:fix-libc-bin-install-issue commit
* Removed unnecessary 'apt-get update' from sonic-slave-buster/Dockerfile.j2
* Fixed saiarcot895 reviewer's requests
* Fixed README and replaced 'sed/awk' with patches
* Fixed ntp build to use openssl
* Unuse sonic-slave-buster/cross-build-arm-python-reqirements.sh script (put all prebuilt python packages cross-compilation/install inside Dockerfile.j2). Fixed src/snmpd/Makefile to use -j1 in all cases
* Clean armhf cross-compilation build fixes
* Ported cross-compilation armhf build to bullseye
* Additional change for bullseye
* Set CROSS_BUILD_ENVIRON default value n
* Removed python2 references
* Fixes after merge with the upstream
* Deleted unused sonic-slave-buster/cross-build-arm-python-reqirements.sh file
* Fixed 2 @saiarcot895 requests
* Fixed @saiarcot895 reviewer's requests
* Removed use of prebuilt python wheels
* Incorporated saiarcot895 CC/CXX and other simplification/generalization changes
Signed-off-by: marvell <marvell@cpss-build3.marvell.com>
* Fixed saiarcot895 reviewer's additional requests
* src/libyang/patch/debian-packaging-files.patch
* Removed --no-deps option when installing wheels. Removed unnecessary lazy_object_proxy arm python3 package instalation
Co-authored-by: marvell <marvell@cpss-build3.marvell.com>
Co-authored-by: marvell <marvell@cpss-build2.marvell.com>
Give more room for the kernel image in memory
Change-Id: I015856d173d50d94e30d8c555590efb70eb712ae
Signed-off-by: Pavan Naregundi <pnaregundi@marvell.com>
This fixes the build for armhf to be able to use '/device///installer.conf' files. Specifically, armhf needs support to be able to change the size of /var/log/ directory. It is hardcoded to 512 bytes on all armhf platforms currently. This change will allow any armhf platform to be able to use an installer.conf file to customize the installed image.
Currently, the build dockers are created as a user dockers(docker-base-stretch-<user>, etc) that are
specific to each user. But the sonic dockers (docker-database, docker-swss, etc) are
created with a fixed docker name and common to all the users.
docker-database:latest
docker-swss:latest
When multiple builds are triggered on the same build server that creates parallel building issue because
all the build jobs are trying to create the same docker with latest tag.
This happens only when sonic dockers are built using native host dockerd for sonic docker image creation.
This patch creates all sonic dockers as user sonic dockers and then, while
saving and loading the user sonic dockers, it rename the user sonic
dockers into correct sonic dockers with tag as latest.
docker-database:latest <== SAVE/LOAD ==> docker-database-<user>:tag
The user sonic docker names are derived from 'DOCKER_USERNAME and DOCKER_USERTAG' make env
variable and using Jinja template, it replaces the FROM docker name with correct user sonic docker name for
loading and saving the docker image.
Why I did it
Kernel hang in during early boot is caused due overwriting of device tree with uncompressing kernel. Added the fdt_high which gives a safe offset from kernel location.
How I did it
Setting uboot environment variable fdt_high.
How to verify it
Successful boot of bullseye kernel on Marvell Armada 380/385.
Change-Id: I3e2521780f5ecdb3bdf6cbb6542250814ca11959
Signed-off-by: Pavan Naregundi <pnaregundi@marvell.com>
Why I did it
Removing incorrect check in plt setup for fw_env config: This check was added before to compare 2 different types of disk. Now the check is redundant and check is not required as transition is complete.
2)Removing legacy_volume_label in create_partition: legacy_volume_label is not used in armhf install files. With legacy_volume_label initialized to NULL, current code will always return true for check, if demo_part exits.
How I did it
Change is about removing the redundant/incorrect code explained above.
How to verify it
uboot fw_printenv and fw_setenv is tested
onie-nos-install has be verified.
Signed-off-by: Pavan Naregundi <pnaregundi@marvell.com>
The following changes are provided to support bullseye and the latest master
branch content.
- Accommodate relocated fan and thermal sysfs entries in bullseye
- Add support for chassis and PSU HW revision
Why I did it
Fix platform issues introduced by the bullseye kernel upgrade.
How I did it
Minor fixes to Nokia ixs7215 platform code
How to verify it
Execute the following CLI commands
show platform summary
show platform fan
show platform temperature
This commit fixes/avoids the following errors encountered during the
marvell-armhf build for bullseye
- Fix Marvell prestera DMA driver build failure due to kallsyms_lookup_name()
no longer being exported by the updated bullseye kernel. This is a temporary
fix that will be replaced by a future version of the DMA driver.
- Update qemu-user-static version to align with the new glibc version included
in bullseye
- Skip systemd-sonic-generator unit tests to avoid test failures. Root cause is
still TBD
#### Why I did it
Fix the following build errors observed when building marvell-armhf for bullseye
1. Marvell Prestera DMA driver uses kernel API no longer exported
ERROR: modpost: "kallsyms_lookup_name" [/sonic/platform/marvell-armhf/prestera/mrvl-prestera/cpssEnabler/linuxNoKernelModule/drivers//mvDmaDrv.ko] undefined!
2. Old qemu-user-static version does not support semop() leading to following build failure
semop(1): encountered an error: Function not implemented
3. systemd-sonic-generator unit test failure
ssg-test.cc:217: Failure
Expected equality of these values:
find_string_in_file(str_t, target, num_asics)
Which is: false
expected_result
Which is: true
Error validating Before=single_inst.service in test.service
[ FAILED ] SsgMainTest.ssg_main_40_npu (20 ms)
[----------] 4 tests from SsgMainTest (36 ms total)
[----------] Global test environment tear-down
[==========] 10 tests from 3 test suites ran. (54 ms total)
[ PASSED ] 7 tests.
[ FAILED ] 3 tests, listed below:
[ FAILED ] SsgMainTest.ssg_main_single_npu
[ FAILED ] SsgMainTest.ssg_main_10_npu
[ FAILED ] SsgMainTest.ssg_main_40_npu
3 FAILED TESTS
- Why I did it
In case an app.ext requires a dependency syncd^1.0.0, the RPC version of syncd will not satisfy this constraint, since 1.0.0-rpc < 1.0.0. This is not correct to put 'rpc' as a prerelease identifier. Instead put 'rpc' as build metadata in the version: 1.0.0+rpc which satisfies the constraint ^1.0.0.
- How I did it
Changed the way how to version in RPC and DBG images are constructed.
- How to verify it
Install app.ext with syncd^1.0.0 dependency on a switch with RPC syncd docker.
Signed-off-by: Stepan Blyshchak <stepanb@nvidia.com>
* [Nokia ixs7215] Platform API fixes
This commit delivers the following fixes
- Fix bug preventing access to second PSU eeprom
- Fix bug preventing updates to front panel PSU status led
- Fix SFP reset test case failure
* Fix LGTM alert
* [Nokia ixs7215] Miscellaneous platform API fixes
This commit delivers the following fixes for the Nokia ixs7215 platform
- Fix bug in a fan API error path
- Add support for setting the fan drawer led
- Add support for getting/setting the front panel PSU status led
- Add support for getting the min/max observed temperature value
* [Nokia ixs7215] code review changes: temperature min/max values
This commit adds support for changing the default console baud rate configured
within the U-Boot bootloader. That default baud rate is exposed via the value
of the U-Boot 'baudrate' environment variable. This commit removes logic that
hardcoded the console baud rate to 115200 and instead ensures that the U-Boot
'baudrate' variable is always used when constructing the Linux kernel boot
arguments used when booting Sonic.
A change is also made to rc.local to ensure that the specified baud rate is set
correctly in the serial getty service.
Deliver sfputil support for sfputil show eeprom and sfputil reset along with some component test case fixes
Co-authored-by: Carl Keene <keene@nokia.com>
